Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Load shaping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

A thermoluminescence study of experimentally shock-loaded oligoclase and bytownite

The thermoluminescence (TL) properties of a terrestrial oligoclase and a bytownite shock-loaded to pressures of 10.5-45 GPa are measured. Glow curves and TL sensitivity levels for the oligoclase and bytownite samples are presented and analyzed; it is detected that shock causes a decrease in the TL sensitivity and changes the shape of the glow curve. The causes of the decrease in TL sensitivity and peak temperature and width variations are examined. Shock-induced disordering of the Al, Si chain, and ordinary chondrite shocks are studied.

Hartmetz, Christopher P.↗
NASA NTRS1989

Composite laminate free-edge reinforcement with U-shaped caps. I - Stress analysis. II - Theoretical-experimental correlation

The present generalized plane-strain FEM analysis for the prediction of interlaminar normal stress reduction when a U-shaped cap is bonded to the edge of a composite laminate gives attention to the highly variable transverse stresses near the free edge, cap length and thickness, and a gap under the cap due to the manufacturing process. The load-transfer mechanism between cap and laminate is found to be strain-compatibility, rather than shear lag. In the second part of this work, the three-dimensional composite material failure criteria are used in a progressive laminate failure analysis to predict failure loads of laminates with different edge-cap designs; symmetric 11-layer graphite-epoxy laminates with a one-layer cap of kevlar-epoxy are shown to carry 130-140 percent greater loading than uncapped laminates, under static tensile and tension-tension fatigue loading.

Howard, W. E.↗
NASA NTRS1992

Investigation of three-dimensional flow field in a turbine including rotor/stator interaction. I - Design development and performance of the research facility

A description of the Axial Flow Turbine Research Facility (AFTRF) installed at the Turbomachinery Laboratory of the Pennsylvania State University is presented in this paper. The facility diameter is 91.66 cm (3 feet) and the hub-to-tip ratio of the blading is 0.73. The flow path consists of turbulence generating grid, 23 nozzle vane and 29 rotor blades followed by outlet guide vanes. The blading design, carried out by General Electric Company personnel, embody modern HP turbine design philosophy, loading and flow coefficient, reaction, aspect ratio, and blade turning angles; all within the current aircraft engine design turbine practice. State-of-the-art quasi-3D blade design techniques were used to design the vane and the blade shapes. The vanes and blades are heavily instrumented with fast response pressure, shear stress, and velocity probes and have provision for flow visualization and laser Doppler anemometer measurement. Furthermore, provision has been made for detailed nozzle wake, rotor wake and boundary layer surveys. A 150 channel slip ring unit is used for transmitting the rotor data to a stationary instrumentation system. All the design objectives have been met.

Lakshminarayana, B.↗
NASA NTRS1994

The Influence of Finite-size Sources in Acousto-ultrasonics

This work explores the effects that the finite normal axisymmetric traction loading of an infinite isotropic plate has on wave propagation in acousto-ultrasonics (AU), in which guided waves are created using two normal incidence transducers. Although the work also addresses the effects of the transducer pressure distribution and pulse shape, this thesis concentrates on two main questions: how does the transducer's diameter control the phase velocity and frequency spectrum of the response, and how does the plate thickness relate to the plate's excitability? The mathematics of the time-harmonic solution and the physical principles and the practical considerations for AU wave generation are explained. Transient sources are modeled by the linear superposition of the time-harmonic solutions found using the Hankel transform and they are then compared to experimental data to provide insight into the relation between the size of the transducer and the preferred phase velocity.

Pavlakovic, Brian N.↗
NASA NTRS2017

Shape Memory Alloys (SMAs) for Non-Pneumatic Tires

Conventional mobility elements, such as pneumatic tires, suffer from a number of issues related to reliability. Two of the more prevalent problems are the high likelihood of single point failure owing to puncture (i.e. flat tire), and loss of efficiency due to reduction in tire pressure over time. In order to overcome these limitations, alternative compliant tire designs not requiring pneumatics have been developed. However, although current designs have significantly reduced the aforementioned issues, they tend to have their own set of limitations. First, non-pneumatic tires designed for high load applications often have restricted envelopment capability, making their performance less than optimal, especially on uneven terrain. Second, tires designed with larger envelopment capability tend to suffer from large amounts of plasticity (permanent deformation) or failure (rupture). Both of these limitations are the direct result of the choice of material being used for the design; conventional metals undergo plastic deformation at low strain while elastomer based designs are often too rigid for the localized deformations needed for high envelopment. Recent advancements at the NASA Glenn research center in a unique class of metals know as shape memory alloys (SMAs) has opened the design space for non-pneumatic compliant tire technologies allowing designs to incorporate orders of magnitude more deformation without damage. The work presented herein highlights the advantages of using SMAs as compared to conventional metals. Additionally, the development of a unique SMA compliant tire design capable of carrying up to 8.9 kN (2000 lbf) with reversible, local deformations on the order of the side wall height will be presented.

Padula, Santo↗
DOE OSTI2023

A simple, validated approach for design of two-dimensional periodic particle patterns via acoustophoresis

Two-dimensional patterning of microparticles enables a wide range of functional materials, including patterned energy storage electrodes, flexible electronics, and sensor arrays. Particle patterning via acoustics offers an attractive path to generate a wide variety of 2D periodic patterns that introduce tailorable hierarchical porosity, useful for controlling surface area, transport distances, and other properties. This method is most effective with micron scale particles and patterns of tens to hundreds of microns. To enable systematic exploration of the broad design space for such patterns, this work develops a model of 2D and 3D assembly of particles at high loadings and validates the obtained patterns against both experiments and more computationally intensive modeling techniques. Using this simple model, connections are mapped between input parameters (like actuation conditions, particle volume fraction, material properties) and output geometrical features (like void size and shape, pattern connectivity, and surface area) so that they can be tailored to given applications. The utility of this simple model is illustrated by predicting and then experimentally demonstrating new hierarchical patterns resulting from multiple waves of different frequencies interacting. These multiscale patterns offer the potential to lift the limits on surface area, diffusion distances, and other features.

42 ENGINEERING↗
DOE OSTI2020

FY20 Status Report on Creep Rupture Testing to Support the Development of Alloy 709 Code Case

This report provides an update on the status of the creep rupture testing on the first commercial heat of Alloy 709 in support of the Alloy 709 Code Case development. A creep test laboratory has been set up at ANL that comprises of 15 indirectly loaded test frames capable of testing ASTM-size specimens of the commercial heat of Alloy 709. The systems are equipped with high temperature furnaces capable of operation up to 1000°C in an air environment. During FY18, uniaxial ASTM-sized creep specimens were fabricated from 9 Alloy 709 plates that were processed by AOD, ESR, and ESR-homogenized routes and subsequently solution annealed at 1050, 1100, and 1150°C, and creep-rupture tests were performed at 330MPa and 600°C. The test results led to the down selection of the ESR-1100°C condition to support the code case. In FY19, 15 creep-rupture tests of the ESR-1100°C material, requiring the use of Type K thermocouples, were initiated to support the 100,000-hour Code Case. 8 tests were completed in FY19. In FY20, 6 tests were completed at the time of writing this report. In addition, 1 more test were loaded in FY20, using Type S thermocouples, and was completed. This report presents the data from the completed tests in FY20 and also the microstructural characterization of the fractured specimens. The creep data enabled the preliminary analysis of the creep behavior of this material. The characterization showed that in brittle fractures, the pores were narrow and thin, and elongated in the direction perpendicular to the loading direction, while in ductile fractures, the pores were much rounder. Dense precipitates were observed in all the samples, the size of which grew with test temperature. Some of the precipitates could be identified to be M23C6 based on their cuboid shape.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1985

Development of a Global 3-D magnetohydrodynamic computational model for solar wind-cometary and planetary studies

The development of a global, 3-D magnetohydrodynamic computational model is described. This model is used to quantitatively describe the detailed continuum field and plasma interaction process of the solar wind with cometary and planetary magneto/ionopause shapes. The present solar wind/terrestrial planet interaction (Level 1) model (which is based on an axisymmetric gas dynamic plus frozen field approximation to the full MHD equations) is extended to a full 3-D gas dynamic (Level 2) approximation. A mass loading capability in the Level 1 interaction model is implemented.

Stahara, S. S.↗
NASA NTRS1984

Galileo spacecraft modal test and evaluation of testing techniques

The structural configuration, modal test requirements and pre-test activities involved in modeling the expected dynamic environment and responses of the Galileo spacecraft are discussed. The probe will be Shuttle-launched in 1986 and will gather data on the Jupiter system. Loads analysis for the 5300 lb spacecraft were performed with the NASTRAN code, and covered 10,000 static degrees of freedom and 1600 mass degrees of freedom. A modal analysis will be used to verify the predictions for natural frequencies, mode shapes, orthogonality checks, residual mass, modal damping and forces, and generalized forces. Verification of the validity of considering only 70 natural modes in the numerical simulation is being performed by examining the forcing functions of the analysis. The analysis led to requirements that 162 channels of accelerometer data and 118 channels of strain gage data be recorded during shaker tests to reveal areas where design changes will be needed to eliminate vibration peaks.

Chen, J.-C.↗
NASA NTRS1999

Design and Performance of Tropical Rainfall Measuring Mission (TRMM) Super NiCd Batteries

The Tropical Rainfall Measuring Mission (TRMM) is a joint mission between NASA and the National Space Development Agency (NASDA) of Japan. The observatory is designed to monitor and study tropical rainfall and the associated release of energy that helps to power the global atmospheric circulation shaping both weather and climate around the globe. The spacecraft was launched from Japan on November 27,1997 via the NASDA H-2 launch vehicle. The TRMM Power Subsystem is a Peak Power Tracking system that can support the maximum TRMM load of 815 watts at the end of its three year life. The Power Subsystem consists of two 50 Ampere Hour Super NiCd batteries, Gallium Arsenide Solar Array and the Power System Electronics. This paper describes the TRMM Power Subsystem, battery design, cell and battery ground test performance, and in-orbit battery operations and performance.

Ahmad, Anisa J.↗
NASA NTRS2004

Parametric Studies of Square Solar Sails Using Finite Element Analysis

Parametric studies are performed on two generic square solar sail designs to identify parameters of interest. The studies are performed on systems-level models of full-scale solar sails, and include geometric nonlinearity and inertia relief, and use a Newton-Raphson scheme to apply sail pre-tensioning and solar pressure. Computational strategies and difficulties encountered during the analyses are also addressed. The purpose of this paper is not to compare the benefits of one sail design over the other. Instead, the results of the parametric studies may be used to identify general response trends, and areas of potential nonlinear structural interactions for future studies. The effects of sail size, sail membrane pre-stress, sail membrane thickness, and boom stiffness on the sail membrane and boom deformations, boom loads, and vibration frequencies are studied. Over the range of parameters studied, the maximum sail deflection and boom deformations are a nonlinear function of the sail properties. In general, the vibration frequencies and modes are closely spaced. For some vibration mode shapes, local deformation patterns that dominate the response are identified. These localized patterns are attributed to the presence of negative stresses in the sail membrane that are artifacts of the assumption of ignoring the effects of wrinkling in the modeling process, and are not believed to be physically meaningful. Over the range of parameters studied, several regions of potential nonlinear modal interaction are identified.

Sleight, David W.↗
NASA NTRS2009

Resilient Flexible Pressure-Activated Seal

A resilient, flexible, pressure-activated, high-temperature seal is adapted to be interposed between high and low pressure regions to provide sealing between opposing surfaces of adjacent relatively movable structures. The seal comprises at least one C-shaped sheet element. The C-shaped element design enables the seal to be pressure-activated to provide a radially outward biasing force, responsive to a seal-activating pressure differential acting across the seal thereby increasing resiliency. A centrally-located, resilient core structure provides load bearing and insulating properties. In an exemplary embodiment where at least two seal elements are used, each layer has a cutout slot pattern and the remaining strip material pattern. The slots provide flexibility to the seal, enabling the seal to be manually contoured to seal around corners and curves. The strip material of each layer covers the slots in each adjacent layer to minimize leakage through the slots. Attached barrier strips can block interface leakage between the seal and the opposing surfaces.

Steinetz, Bruce M.↗
NASA NTRS2011

Characterization of the as Manufactured Variability in a CVI SiC/SiC Woven Composite

The microstructure of a 2D woven ceramic matrix composite displays significant variability and irregularity. For example, a chemical vapor infiltrated (CVI) SiC/SiC composite exhibits significant amount of porosity arranged in irregular patterns. Furthermore, the fiber tows within a ply frequently have irregular shape and spacing, and the stacked plies are often misaligned and irregularly nested within each other. The goal of an ongoing project at NASA Glenn is to investigate the effects of the complex microstructure and its variability on the properties and the durability of the material. One key requirement for this effort is the development of methods to characterize the distribution in as-fabricated ceramic matrix composite (CMC) microstructures with the objective of correlating microstructural distribution parameters with mechanical performance. An initial task in this effort was to perform quantitative image analysis of polished cross sections of CVI SiC/SiC composite specimens. This analysis provided sample distributions of various microstructural composite features, including: inter-tow pore sizes and shapes, transverse sectioned tow sizes and shapes, and within ply tow spacing. This information can then be used to quantify the effect of extreme values of these features on the local stress state with the goal of determining the likelihood of matrix cracking at a given external load.

Bonacuse, Peter J.↗
DOE OSTI2022

Bayesian-based response expansion and uncertainty quantification using sparse measurement sets

Systems subjected to dynamic loads often require monitoring of their vibrational response, but limitations on the total number and placement of the measurement sensors can hinder the data-collection process. Here, we present an indirect approach to estimate a system’s full-field dynamic response, including all uninstrumented locations, using response measurements from sensors sparsely located on the system. This approach relies on Bayesian inference that utilizes a system model to estimate the full-field response and quantify the uncertainty in these estimates. By casting the estimation problem in the frequency domain, this approach utilizes the modal frequency response functions as a natural, frequency-dependent weighting scheme for the system mode shapes to perform the expansion. This frequency-dependent weighting scheme enables an accurate expansion, even with highly correlated mode shapes that may arise from spatial aliasing due to the limited number of sensors, provided these correlated modes do not have natural frequencies that are closely spaced. Furthermore, the inherent regularization mechanism that arises in this Bayesian-based procedure enables the utilization of the full set of system mode shapes for the expansion, rather than any reduced subset. This approach can produce estimates when considering a single realization of the measured responses, and with some modification, it can also produce estimates for power spectral density matrices measured from many realizations of the responses from statistically stationary random processes. A simply supported beam provides an initial numerical validation, and a cylindrical test article excited by acoustic loads in a reverberation chamber provides experimental validation.

42 ENGINEERING↗
NASA NTRS2016

Applications of Displacement Transfer Functions to Deformed Shape Predictions of the G-III Swept-Wing Structure

In support of the Adaptive Compliant Trailing Edge [ACTE] project at the NASA Armstrong Flight Research Center, displacement transfer functions were applied to the swept wing of a Gulfstream G-III airplane (Gulfstream Aerospace Corporation, Savannah, Georgia) to obtain deformed shape predictions. Four strainsensing lines (two on the lower surface, two on the upper surface) were used to calculate the deformed shape of the G III wing under bending and torsion. There being an insufficient number of surface strain sensors, the existing G III wing box finite element model was used to generate simulated surface strains for input to the displacement transfer functions. The resulting predicted deflections have good correlation with the finite-element generated deflections as well as the measured deflections from the ground load calibration test. The convergence study showed that the displacement prediction error at the G III wing tip can be reduced by increasing the number of strain stations (for each strain-sensing line) down to a minimum error of l.6 percent at 17 strain stations; using more than 17 strain stations yielded no benefit because the error slightly increased to 1.9% when 32 strain stations were used.

displacement theory↗
DOE OSTI2021

Effect of plasticity on the experimental characterization of the creep property of a cement paste: Spherical vs. conical microindentation

Microindentation is today a powerful tool for rapidly characterizing the elastic modulus and the logarithmic basic creep of a cement paste. However, a theoretical work proved that a microindentation test with a sharp indenter shape involves stress concentration and delayed plasticity which can cause an overestimation of the estimated creep property. This work aims at experimentally investigating the effect of the shape indenter on the identification of the visco-elastic property of a cement paste by microindentation. First, several microindentation grids were carried out on a cement paste with both a Berkovich indenter and a spherical indenter at different penetration depths or load levels for load control (creep) tests or displacement control (relaxation) tests, respectively. As for a visco-elastic material the duality principle between creep and relaxation holds, a numerical method was developed for predicting the relaxation response from the assumed logarithmic creep compliance. The present results show that only spherical microindentation satisfy the duality principle for which creep and relaxation response can be predicted by a unique logarithmic creep compliance function. Finally, spherical microindentation creep tests at low load as well as spherical microindentation relaxation tests provide a greater indentation modulus M and contact creep modulus C{sub v} as likely less affected by possible plasticity effects.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High-Energy X-Ray Diffraction Microscopy in Materials Science

High-energy diffraction microscopy (HEDM) is an implementation of three-dimensional X-ray diffraction microscopy. HEDM yields maps of internal crystal orientation fields, strain states, grain shapes and locations as well as intragranular orientation distributions, and grain boundary character. Because it is nondestructive in hard materials, notably metals and ceramics, HEDM has been used to study responses of these materials to external fields including high temperature and mechanical loading. Currently available sources and detectors lead to a spatial resolution of ~1 μm and an orientation resolution of <0.1°. With the penetration characteristic of high energies ( E ≥ 50 keV), sample cross-section dimensions of ~1 mm can be studied in materials containing elements across much of the Periodic Table. This review describes hardware and software associated with HEDM as well as examples of applications. Overall, these applications include studies of grain growth, recrystallization, texture development, orientation gradients, deformation twinning, annealing twinning, plastic deformation, and additive manufacturing. We also describe relationships to other X-ray-based methods as well as prospects for further development.

36 MATERIALS SCIENCE↗