Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LUBRICATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Analysis of a spacecraft instrument ball bearing assembly lubricated by a perfluoroalkylether

An analysis of a spacecraft instrument ball bearing assembly, subjected to a scanning life test, was performed to determine the possible case of rotational problems involving these units aboard several satellites. The analysis indicated an ineffective transfer of a fluorinated liquid lubricant from a phenolic retainer to the bearing balls. Part of the analysis led to a novel HPLC separation method employing a fluorinated mobile phase in conjunction with silica based size exclusion columns.

Morales, W.↗
NASA NTRS1985

Analysis of DRIRU bearings and lubricant from solar max repair mission

The Solar Maximum Repair Mission (SMRM) by the shuttle astronauts in April 1984, returned to Earth the Delta Redundant Inertial Reference Unit 2 (DRIRU 2) from the Solar Maximum satellite. The DRIRU 2 included three gyroscopes. The gyroscope, S/N 094, in position 2 was disassembled by Teledyne Systems personnel of Northridge, California, and the bearings were returned to Goddard Space Flight Center for examination. The Solar Max Satellite was in orbit for 4 years with the bearings running continuously at 6000 rpm. The ball bearings, had sufficient remaining lubrication and had runs successfully for over the last 4 years. As a result of these findings, the bearings should have lasted their predicted life of 5 years with no problems.

Uber, J. M.↗
NASA NTRS1987

Carbide-fluoride-silver self-lubricating composite

A self-lubricating, friction and wear reducing composite material is described for use over a wide temperature spectrum from cryogenic temperature to about 900 C in a chemically reactive environment comprising silver, barium fluoride/calcium fluoride eutectic, and metal bonded chromium carbide.

Sliney, Harold E.↗
NASA NTRS1987

Composition optimization of chromium carbide based solid lubricant coatings for foil gas bearings at temperatures to 650 C

A test program to determine the optimum composition of chromium carbide based solid lubricant coatings for compliant gas bearings is described. The friction and wear properties of the coatings are evaluated using a foil gas bearing test apparatus. The various coatings were prepared by powder blending, then plasma sprayed onto Inconel 718 test journals and diamond ground to the desired coating thickness and surface finish. The journals were operated against preoxidized nickel-chromium alloy foils. The test bearings were subjected to repeated start/stop cycles under a 14 kPa (2 psi) bearing unit load. The bearings were tested for 9000 start/stop cycles or until the specimen wear reached a predetermined failure level. In general, the addition of silver and eutectic to the chromium carbide base stock significantly reduced foil wear and increased journal coating wear. The optimum coating composition, PS212 (70 wt% metal bonded Cr3C2, 15 wt% Ag, 15% BaF2/CaF2 eutectic), reduced foil wear by a factor of two and displayed coating wear well within acceptable limits. The load capacity of the bearing using the plasma-sprayed coating prior to and after a run-in period was ascertained and compared to polished Inconel 718 specimens.

Dellacorte, Christopher↗
NASA NTRS1987

Composition optimization of self-lubricating chromium-carbide-based composite coatings for use to 760 C

This paper describes new compositions of self-lubricating coatings that contain chromium carbide. A bonded chromium carbide was used as the base stock because of the known excellent wear resistance and the chemical stability of chromium carbide. Additives were silver and barium fluoride/calcium fluoride eutectic. The coating constituents were treated as a ternary system consisting of: (1) the bonded carbide base material, (2) silver, and (3) the eutectic. A study to determine the optimum amounts of each constituent was performed. The various compositions were prepared by powder blending. The blended powders were then plasma sprayed onto superalloy substrates and diamond ground to the desired coating thickness. Friction and wear studies were performed at temperatures from 25 to 760 C in helium and hydrogen. A variety of counterface materials were evaluated with the objective of discovering a satisfactory metal/coating sliding combination for potential applications such as piston ring/cylinder liner couples for Stirling engines.

Dellacorte, Chris↗
NASA NTRS1988

Transfer Lubrication For Cryogenic Bearings

Report presents evaluation of bronze-filled polytetrafluoroethylene (PTFE), known as Salox M, as cage material for ball bearings in high-pressure turbopumps for liquid oxygen. Material evaluated as potentially longer-lived replacement for glass-filled PTFE, known as Armalon. Cage transfers PTFE to balls to form solid lubricant film. However, glass fibers in glass-filled material tend to interfere with transfer. Two cage-design concepts developed; one involves metal-reinforced cage of bronze-filled PTFE; other calls for bronze-filled PTFE inserts in metal structure.

Barber, S. A.↗
NASA NTRS1988

Lubrication And Wear Of Hot Ceramics

Report presents results of experiments on tribological properties of ceramics. Describes friction and wear characteristics of some ceramics under consideration for use in gas turbines, diesel engines, and Stirling engines. Discusses formulation of composite plasma-sprayed ceramics containing solid lubricant additives, and data for carbide- and oxide-based composite coatings for use at temperatures up to at least 900 degree C.

Sliney, H. E.↗
NASA NTRS1988

On the performance of finite journal bearings lubricated with micropolar fluids

A study of the performance parameters for a journal bearing of finite length lubricated with micropolar fluids is undertaken. Results indicate that a significantly higher load carrying capacity than the Newtonian fluids may result depending on the size of material characteristic length and the coupling number. It is also shown that although the frictional force associated with micropolar fluid is in general higher than that of a Newtonian fluid, the friction coefficient of micropolar fluids tends to be lower than that of the Newtonian.

Khonsari, M. M.↗
NASA NTRS1988

On the torque and wear behavior of selected thin film MOS2 lubricated gimbal bearings

During the thermal vacuum test phase of the GOES 7 spacecraft, the primary scan mirror system exhibited unacceptably high drive friction. The observed friction was found to correlate with small misalignments in the mirror structure and unavoidable loads induced by the vehicle spin. An intensive effort to understand and document the performance of the scan mirror bearing system under these loads is described. This effort involved calculation of the bearing loads and expected friction torque, comparison of the computed values to test data, and verification of the lubrication system performance and limitations under external loads. The study culminated in a successful system launch in February of 1987. The system has operated as predicted since that time.

Bohner, John J.↗
NASA NTRS1987

A model for the influence of pressure on the bulk modulus and the influence of temperature on the solidification pressure for liquid lubricants

Two pressure chambers, for compression experiments with liquids from zero to 2.2 GPa pressure, are described. The experimentally measured compressions are then compared to theoretical values given by an isothermal model of equation of state recently introduced for solids. The model describes the pressure and bulk modulus as a function of compression for different types of lubricants with a very high accuracy up to the pressure limit of the high pressure chamber used (2.2 GPa). In addition the influence of temperature on static solidification pressure was found to be a simple function of the thermal expansion of the fluid.

Jacobson, Bo O.↗
NASA NTRS1988

Parched elasto hydrodynamic lubrication film thickness measurement in an instrument ball bearing

Parched Elasto Hydrodynamic Lubricant (PEHL) film thickness in a large instrument ball bearing is measured by electrical capacitance across its ball set. Correlation is shown between changes in film thickness and changes in Basic Speed Ratio (BSR) measured at the same time. BSR is confirmed as a sensitive, non-intrusive measure of transients in film thickness in a real bearing.

Kingsbury, E.↗
NASA NTRS1989

The role of thermal and lubricant boundary layers in the transient thermal analysis of spur gears

An improved convection heat-transfer model has been developed for the prediction of the transient tooth surface temperature of spur gears. The dissipative quality of the lubricating fluid is shown to be limited to the capacity extent of the thermal boundary layer. This phenomenon can be of significance in the determination of the thermal limit of gears accelerating to the point where gear scoring occurs. Steady-state temperature prediction is improved considerably through the use of a variable integration time step that substantially reduces computer time. Computer-generated plots of temperature contours enable the user to animate the propagation of the thermal wave as the gears come into and out of contact, thus contributing to better understanding of this complex problem. This model has a much better capability at predicting gear-tooth temperatures than previous models.

El-Bayoumy, L. E.↗
NASA NTRS1989

Acidic attack of perfluorinated alkyl ether lubricant molecules by metal oxide surfaces

The reactions of linear perfluoropolyalkylether (PFAE) lubricants with alpha-Fe2O3 and Fe2O3-based solid superacids were studied. The reaction with alpha-Fe2O3 proceeds in two stages. The first stage is an initial slow catalytic decomposition of the fluid. This reaction releases reactive gaseous products which attach the metal oxide and convert it to FeF3. The second stage is a more rapid decomposition of the fluid, effected by the surface FeF3. A study of the inital breakdown step was performed using alpha-Fe2O3, alpha-Fe2O3 preconverted to FeF3, and sulfate-promoted alpha-Fe2O3 superacids. The results indicate that the breakdown reaction involves acidic attack at fluorine atoms on acetal carbons in the linear PFAE. Possible approaches to combat the problem are outlined.

Zehe, Michael J.↗
NASA NTRS1989

On the performance of finite journal bearings lubricated with micropolar fluids

A study of the performance parameters for a journal bearing of finite length lubricated with micropolar fluids is undertaken. Results indicate that a significantly higher load carrying capacity than the Newtonian fluids may result depending on the size of material characteristics length and the coupling number. It is also shown that although the frictional force associated with micropolar fluid is, in general, higher than that of a Newtonian fluid, the friction coefficient of micropolar fluids tends to be lower than that of the Newtonian.

Khonsari, M. M.↗
NASA NTRS1990

Making Self-Lubricating Parts By Powder Metallurgy

Compositions and parameters of powder-metallurgical fabrication processes determined for new class of low-friction, low-wear, self-lubricating materials. Used in oxidizing or reducing atmospheres in bearings and seals, at temperatures from below 25 degrees C to as high as 900 degrees C. Thick parts made with minimal waste.

Sliney, Harold E.↗
NASA NTRS1990

On the numerical solution of the dynamically loaded hydrodynamic lubrication of the point contact problem

The transient analysis of hydrodynamic lubrication of a point-contact is presented. A body-fitted coordinate system is introduced to transform the physical domain to a rectangular computational domain, enabling the use of the Newton-Raphson method for determining pressures and locating the cavitation boundary, where the Reynolds boundary condition is specified. In order to obtain the transient solution, an explicit Euler method is used to effect a time march. The transient dynamic load is a sinusoidal function of time with frequency, fractional loading, and mean load as parameters. Results include the variation of the minimum film thickness and phase-lag with time as functions of excitation frequency. The results are compared with the analytic solution to the transient step bearing problem with the same dynamic loading function. The similarities of the results suggest an approximate model of the point contact minimum film thickness solution.

Lim, Sang G.↗