Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Jet Surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

NO formation by N 2 /O 2 plasma catalysis: The impact of surface reactions, gas-phase reactions, and mass transport

Pathways and timescales relevant to facilitate plasma-assisted N 2 -O 2 reactions are assessed by measuring the consumption of plasma-derived N and the formation of NO in the gas phase and over Ag catalytic surfaces. These measurements are enabled by a setup that enables N 2 activation in an atmospheric pressure RF plasma jet, enables O 2 addition in the plasma afterglow, facilitates reactions over an Ag wire catalyst, and allows species density quantification by molecular beam mass spectrometry. Gas-phase reactions consume N but do not form NO with high selectivity. The presence of the non-porous Ag wire catalyst increases the rate of N conversion to NO, though mass transfer processes, not surface reactions, dictate the rate of N consumption. When O 2 concentrations and the ratio of the surface area of the catalyst to the void volume of the reactor are high (3–5 mol% O 2 , 10900 m –1 ), N conversion to NO reaches 100 % selectivity. When both N 2 and O 2 are fed through the plasma jet, gas-phase NO production increases 10×, although plasma and gas-phase processes do not exclusively produce NO. Above a threshold NO density, N cannot diffuse to the catalyst surface faster than it is consumed in the gas phase by reactions with NO. Furthermore, the use of heterogeneous catalysts to enhance plasma-driven N x O y formation and control N x O y product selectivity is limited to cases where diffusive transport of N from the gas phase to the catalyst surface is faster than consumption of N from gas-phase reactions with NO.

Engineering↗
DOE OSTI2023

OH density, flux and loss probability measurements in a room temperature atmospheric pressure surface discharge by microscopic laser induced fluorescence

Many applications involving atmospheric pressure plasma-substrate interactions are enabled by the large fluxes of short-lived reactive species such as OH radicals to the substrate, nonetheless, the accurate measurement of radical densities and fluxes at substrates at atmospheric pressure has received little attention to date, particularly for surface ionization waves. We report the measurement of the OH density distribution in a surface discharge on a fused silica (quartz) substrate generated by an impinging atmospheric pressure plasma jet in dry and humid helium. The OH density is measured by microscopic laser induced fluorescence with a spatial resolution of 10 µm in the direction perpendicular to the quartz substrate. The measured OH diffusive flux varied for the investigated experimental conditions by almost three orders of magnitude and had a maximum value of 1.7 × 10 15 cm -2 s -1 . The corresponding surface loss probability of OH on the quartz surface was determined to be ~0.01. The high spatial resolution was required to accurately resolve the near surface gradient of OH radicals.

plasma-surface interactions↗
DOE OSTI2026

Seasonal variation of the surface cross-shelf exchange in the northern South China Sea: a Lagrangian perspective

Previous studies on cross-shelf exchange, predominantly adopted an Eulerian perspective, struggled to identify water sources and pathways. Using a high-resolution regional ocean modeling system (ROMS) and Lagrangian particle tracking, this study systematically investigates the seasonal variation and dynamics of surface cross-shelf exchange in the northern South China Sea (NSCS) from a Lagrangian perspective. Based on daily released 30-day drifter trajectories we identify the key pathways, source regions for surface cross-shelf exchange, revealing pronounced seasonal variability. Results show the surface cross-shelf exchange generally following monsoon-driven Ekman transport. However, local dynamics, especially topographic modulation, can outweigh the expected Ekman-driven transport, producing surface exchange patterns opposite to that predicted from the prevailing winds. Topographic effects vary across different scales. In the coastal waters of western Guangdong during winter, despite downwelling-favorable winds, the modulation of alongshore currents by island topography induces an eastward pressure gradient. This gradient, through geostrophic balance, drives offshore flows opposite to wind-driven Ekman onshore transport. Furthermore, the eastern widened shelf exhibits a distinct seasonal variation of cross-shelf exchange, with strong offshore transport (opposite to the direction of Ekman transport) in winter and exceedingly weak exchange in summer. Analysis of the underlying mechanisms reveals that this winter offshore transport is primarily attributed to geostrophic flows driven by surface pressure gradient that is jointly modulated by the Kuroshio intrusion and local widened shelf topography, and enhanced by cumulative submesoscale processes. In summer, a persistent and strong along-isobath jet acts as a dynamic barrier, effectively suppressing the exchange. These findings highlight the important role of topography in regulating surface material transport, and have important implications for predicting the advection and dispersion of plankton or oil spills over the continental shelf influenced by monsoon.

Hao, Dongliang↗
DOE OSTI2021

Atomic oxygen density determination in the effluent of the COST reference source using in situ effective lifetime measurements in the presence of a liquid interface

Abstract Spatially resolved, absolute densities of atomic oxygen are measured for several helium-based admixtures in the effluent of the COST Reference Microplasma Jet using two-photon absorption laser induced fluorescence (TALIF). Admixtures investigated include a helium-only admixture, four helium/oxygen admixtures (0.1 % , 0.5 % , 0.6 % , and 1.0 % oxygen), and a helium/water admixture (2500 ppm water), chosen to coincide with previously published characterizations of plasma-treated liquid. The atomic oxygen TALIF signal is calibrated for density using the noble gas xenon, which possesses a very similar two-photon excitation and fluorescence scheme. Measurements are conducted for the jet operating in ambient air with both an open effluent and a liquid surface present, allowing for comparison with liquid phase measurements conducted under similar conditions. The presence of a water surface does not appear to alter the background chemistry in the effluent but reduces O densities close to the liquid interface when compared to a similar distance from the nozzle in an open effluent case. This may be the result of a reduction in flow velocity caused by the liquid obstructing the gas flow. Additionally, measurements near the liquid surface revealed a region of atomic oxygen well outside of where the core of the effluent impinges on the liquid. This is likely relevant for applications as it considerably expands the surface area subject to O absorption. Critically, in situ measurements of the effective lifetimes of the laser-excited 3p 3 P J state of atomic oxygen were recorded in the effluent by employing a picosecond (ps) laser and a nanosecond (ns) ICCD. By experimentally determining the contribution from collisional quenching via the in situ effective lifetime measurements, significant improvements in the accuracy of the atomic oxygen density calibration were made, with differences of approximately 30 % from existing methods of estimating quenching rates at atmospheric pressure. Finally, spatially resolved atomic oxygen densities allow for an investigation of O formation and extinction pathways in the effluent and a comparison between admixtures.

laser diagnostics↗
NASA NTRSDate not supplied

Study of Graphite Ablation at Arc-Jet Conditions using Finite-Rate and Equilibrium Chemistry Models

Moving at hypersonic speeds through the atmosphere generates immense amount of heat that triggers thermo-chemical non-equilibrium effects in the flow approaching the vehicle and leads to surface chemical reactions that cause ablation and consume the material mass. This complex behavior and interaction of the aerothermal environment with a graphite surface is com- putationally modeled in the present work using a fully-coupled simulation between flow solver CHAMPS NBS-Cart and material response solver KATS-MR. In this study, we account for the thermo-chemical non-equilibrium effects occurring in the flow and use an 11-species air-carbon re- action model to simulate the ablation of the material. The reactions at the surface such oxidation, nitridation and recombination are modeled with a newly developed air-carbon reaction model. The coupled simulation is applied to study two experimental cases performed at IHF arc-jet facility at NASA Ames research center. The obtained results are compared against the measured data of surface recession, as well as surface and in-depth temperatures. Additionally, uncoupled sim- ulations, performed with equilibrium chemistry at the wall, point out the substantial differences between the coupled and uncoupled solutions, leading to higher deviation of the predicted temper- atures. Overall, we show excellent agreement between the coupled simulation predictions and the experimental data in all measured quantities.

EDL↗
NASA NTRS2010

Integration of Advanced Concepts and Vehicles Into the Next Generation Air Transportation System: Introduction, Key Messages, and Vehicle Attributes - Volume 1

Raytheon, in partnership with NASA, is leading the way in ensuring that the future air transportation continues to be a key driver of economic growth and stability and that this system provides an environmentally friendly, safe, and effective means of moving people and goods. A Raytheon-led team of industry and academic experts, under NASA contract NNA08BA47C, looked at the potential issues and impact of introducing four new classes of advanced aircraft into the next generation air transportation system -- known as NextGen. The study will help determine where NASA should further invest in research to support the safe introduction of these new air vehicles. Small uncrewed or unmanned aerial systems (SUAS), super heavy transports (SHT) including hybrid wing body versions (HWB), very light jets (VLJ), and supersonic business jets (SSBJ) are the four classes of aircraft that we studied. Understanding each vehicle's business purpose and strategy is critical to assessing the feasibility of new aircraft operations and their impact on NextGen's architecture. The Raytheon team used scenarios created by aviation experts that depict vehicles in year 2025 operations along with scripts or use cases to understand the issues presented by these new types of vehicles. The information was then mapped into the Joint Planning and Development Office's (JPDO s) Enterprise Architecture to show how the vehicles will fit into NextGen's Concept of Operations. The team also identified significant changes to the JPDO's Integrated Work Plan (IWP) to optimize the NextGen vision for these vehicles. Using a proven enterprise architecture approach and the JPDO s Joint Planning Environment (JPE) web site helped make the leap from architecture to planning efficient, manageable and achievable. Very Light Jets flying into busy hub airports -- Supersonic Business Jets needing to climb and descend rapidly to achieve the necessary altitude Super-heavy cargo planes requiring the shortest common flight path -- are just a few of the potential new operations in the future National Airspace System. To assess the impact of these new scenarios on overall national airspace operations, the Raytheon team used the capabilities of a suite of tools such as NASA's Airspace Concepts Evaluation System (ACES), the Flight Optimization System (FLOPS), FAA's Aviation Environmental Design Tool (AEDT), Intelligent Automations Kinematic Trajectory Generator (KTG) and the Aviation Safety Risk Model (ASRM). Detailed metroplex modeling, surface delay models for super heavy transports, prioritized routing and corridors for supersonics business jets, and VLJ demand models are some of the models developed by the Raytheon team to study the effect of operating these new vehicles in the future NAS. Using this suite of models, several trade studies were conducted to evaluate these effects in terms of delays, equity in access, safety, and the environment. Looking at the impact of each vehicle, a number of critical issues were identified. The Raytheon team concluded that strict compliance to NextGen's 4-dimensional trajectory (4DT) management will be required to accommodate these vehicles unique operations and increased number of flights in the future air space system. The next section provides a discussion of this and the other key findings from our study.

Zellweger, Andres↗
NASA NTRS1998

Computational Analysis of Shock Layer Emission Measurements in an Arc-Jet Facility

This paper reports computational analysis of radiation emission experiments in a high enthalpy arc-jet wind tunnel at NASA Ames Research Center. Recently, as part of ongoing arc-jet characterization work, spectroscopic radiation emission experiments have been conducted at the 20 MW NASA Ames arc-jet facility. The emission measurements were obtained from the arc-jet freestream and from a shock layer formed in front of flatfaced models. Analysis of these data is expected to provide valuable information about the thermodynamic state of the gas in the arc-jet freestream and in the shock layer as well as thermochemical equilibration processes behind the shock in arc-jet flows. Knowledge of the thermodynamic state of the gas in arc-jet test flows and especially within the shock layer is essential to interpret the heat transfer measurements such as in surface catalysis experiments. The present work is a continuation of previous work and focuses on analysis of the emission data obtained at relatively low-pressure conditions for which the arc-jet shock layer is expected to be in thermal and chemical nonequilibrium. Building blocks of the present computational analysis are: (1) simulation of nonequilibrium expanding flow in the converging-diverging conical nozzle and supersonic jet; (2) simulation of nonequilibrium shock layer formed in front of the flat-faced cylinder model; and (3) prediction of line-of-sight radiation from the computed flowfield. For computations of the nonequilibrium flow in the conical nozzle and shock layer, multi-temperature nonequilibrium codes with the axisymmetric formulation are used. For computations of line-of-sight radiation. a nonequilibrium radiation code (NEQAIR) is used to predict emission spectra from the computed flowfield. Computed line-of-sight averaged flow properties such as vibrational and rotational temperatures, species number densities within the shock layer will be compared with those deduced from the experimental spectra. Detailed comparisons of computational and experimental spectra will also be presented.

Gokcen, Tahir↗
NASA NTRS1987

Raman spectra of adsorbed layers on space shuttle and AOTV thermal protection system surface

Surfaces of interest to space vehicle heat shield design were struck by a 2 W argon ion laser line while subjected to supersonic arc jet flow conditions. Emission spectra were taken at 90 deg to the angle of laser incidence on the test object. Results showed possible weak Raman shifts which could not be directly tied to any particular parameter such as surface temperature or gas composition. The investigation must be considered exploratory in terms of findings. Many undesirable effects were found and corrected as the project progressed. For instance, initial spectra settings led to ghosts which were eliminated by closing the intermediate of filter slit of the Spex from 8 to 3 mm. Further, under certain conditions, plasma lines from the laser were observed. Several materials were also investigated at room temperature for Raman shifts. Results showed Raman shifts for RCC and TEOS coated materials. The HRSI materials showed only weak Raman shifts, however, substantial efforts were made in studying these materials. Baseline materials showed the technique to be sound. The original goal was to find a Raman shift for the High-temperature Reusable Surface Insulation (HRSI) Reaction Cured borosilicate Glass (RCG) coated material and tie the amplitude of this peak to Arc jet conditions. Weak Raman shifts may be present, however, time limitations prevented confirmation.

Willey, Ronald J.↗
DOE OSTI2020

Downward jetting of a dynamic Leidenfrost drop

Jetting is a universal phenomenon frequently observed in nature and industries, for instance in rain drop impact, inkjet printing, spray cooling, fuel atomization, etc. In drop impact on a superheated surface, we observe the formation of a vapor cavity beneath the dynamic Leidenfrost drop and a consecutive downward ejection of a jet into the cavity, using ultrafast x-ray phase contrast imaging. We reveal that the cavity is induced mostly by the retraction of the drop and the jetting is caused by the convergence of capillary waves along the liquid-cavity interface. We find a jetting criterion based on the viscous damping of capillary waves: [OhWe 2 ] ≤ 66 ± 10. These results can provide important insight that leads to understanding and modeling of jets in nature.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS2010

Bubble Departure from Metal-Graphite Composite Surfaces and Its Effects on Pool Boiling Heat Transfer

The formation and growth processes of a bubble in the vicinity of graphite micro-fiber tips on metal-graphite composite boiling surfaces and their effects on boiling behavior are investigated. It is discovered that a large number of micro bubbles are formed first at the micro scratches and cavities on the metal matrix in pool boiling. By virtue of the non-wetting property of graphite, once the growing micro bubbles touch the graphite tips, the micro bubbles are sucked by the tips and merged into larger micro bubbles sitting on the end of the tips. The micro bubbles grow rapidly and coalesce to form macro bubbles, each spanning several tips. The necking process of a detaching macro bubble is analyzed. It is revealed that a liquid jet is produced by sudden break-off of the bubble throat. The composite surfaces not only have higher temperatures in micro- and macrolayers but also make higher frequency of the bubble departure, which increase the average heat fluxes in both the bubble growth stage and in the bubble departure period. Based on these analyses, the enhancement mechanism of pool boiling heat transfer on composite surfaces is clearly revealed.

Chao, David F.↗
NASA NTRS2004

Analysis of Upper Air, Ground and Remote Sensing Data For the ATLAS Field Campaign in San Juan, Puerto Rico

The Atlas San Juan Mission was conducted in February 2004 with the main objectives of observing the Urban Heat Island of San Juan, providing high resolution data of the land use for El Yunque Rain Forest and for calibrating remote sensors. The mission was coordinated with NASA staff members at Marshall, Stennis, Goddard, and Glenn. The Airborne Thermal and Land Applications Sensor (ATLAS) from NASA/Stennis, that operates in the visual and IR bands, was used as the main sensor and was flown over Puerto Rico in a Lear 23 jet plane. To support the data gathering effort by the ATLAS sensor, remote sensing observations and upper air soundings were conducted along with the deployment of a number of ground based weather stations and temperature sensors. This presentation focuses in the analysis of this complementary data for the Atlas San Juan Mission. Upper air data show that during the days of the mission the Caribbean mid and high atmospheres were relatively dry and highly stable reflecting positive surface lifted index, a necessary condition to conduct this suborbital campaign. Surface wind patterns at levels below 850mb were dominated by the easterly trades, while the jet stream at the edge of the troposphere dominated the westerly wind at levels above 500mb. The jet stream remained at high latitudes reducing the possibility of fronts. In consequence, only 8.4 mm of precipitation were reported during the entire mission. Observation of soundings located about 150 km apart reflected minimum variations of the boundary layer across the island for levels below 850 meters and a uniform atmosphere for higher levels. The weather stations and the temperature sensors were placed at strategic locations to observe variations across the urban and rural landscapes. Time series plot of the stations' data show that heavily urbanized commercial areas have higher air temperatures than urban and suburban residential areas, and much higher temperatures than rural areas. Temperature differences [dT(U-R)] were obtained by subtracting the values of several stations from a reference urban station, located in the commercial area of San Juan. These time series show that the UHI peaks during the morning between 10:00am and noon to an average of 4.5 C, a temporal pattern not previously observed in similar studies for continental cities. It is also observed a high variability of the UHI with the precipitation patterns even for short events. These results may be a reflection of a large land use density by low level buildings with an apparent absence of significant heat storage effects in the urban areas, and the importance of the surrounding soil and vegetation moisture in controlling the urban tropical climate. The ATLAS data was used to determine albedo and surface temperature patterns on a 10m scale for the study area. These data were used to calibrate the spatial distribution of the surface temperature when using remote sensing images from MODIS (Moderate Resolution Imaging Spectroradiometer). Surface temperatures were estimated using the land surface temperature product MOD11_L2 distributed by the Land Process Distributed Active Archive Center (LP DAAC). These results show the maximum, minimum and average temperatures in San Juan and in the entire Island at a resolution of 1 km. The information retrieved from MODIS for land surface temperatures reflected similar temporal and spatial variations as the weather stations and ATLAS measurements with a highest absolute offset of about 5 C due to the differences between surface and air temperatures.

Gonzalez, J. E.↗
NASA NTRS2005

Analysis of Upper Air, Ground and Remote Sensing Data for the ATLAS Field Campaign in San Juan, Puerto Rico

The Atlas San Juan Mission was conducted in February 2004 with the main objectives of observing the Urban Heat Island of San Juan, providing high resolution data of the land use for El Yunque Rain Forest and for calibrating remote sensors. The mission was coordinated with NASA staff members at Marsha& Stennis, Goddard, and Glenn. The Airborne Thermal and Land Applications Sensor (ATLAS) from NASA/Stennis, that operates in the visual and IR bands, was used as the main sensor and was flown over Puerto Rico in a Lear 23 jet plane. To support the data gathering effort by the ATLAS sensor, remote sensing observations and upper air soundings were conducted along with the deployment of a number of ground based weather stations and temperature sensors. This presentation focuses in the analysis of this complementary data for the Atlas San Juan Mission. Upper air data show that during the days of the mission the Caribbean mid and high atmospheres were relatively dry and highly stable reflecting positive surface lifted index, a necessary condition to conduct this suborbital campaign. Surface wind patterns at levels below 850mb were dominated by the easterly trades, while the jet stream at the edge of the troposphere dominated the westerly wind at levels above 500mb. The jet stream remained at high latitudes reducing the possibility of fronts. In consequence, only 8.4 mm of precipitation were reported during the entire mission. Observation of soundings located about 150 km apart reflected minimum variations of the boundary layer across the Island for levels below 850 meters and a uniform atmosphere for higher levels. The weather stations and the temperature sensors were placed at strategic locations to observe variations across the urban and rural landscapes. Time series plot of the stations' data show that heavily urbanized commercial areas have higher air temperatures than urban and suburban residential areas, and much higher temperatures than rural areas. Temperature differences [dT(U-R)] were obtained by subtracting the values of several stations h m a reference urban station, located m the commercial area of San Juan. These time series show that the UHI peaks during the morning between 10:00am and noon to an average of 4.5 C, a temporal pattern not previously observed in similar studies for continental cities. It is also observed a high variability of the UHI with the precipitation patterns even for short events. These results may be a reflection of a large land use density by low level buildings with an apparent absence of significant heat storage effects in the urban areas, and the importance of the surrounding soil and vegetation moisture in controlling the urban tropical climate. The ATLAS data was used to determine albedo and surface temperature patterns on a 10m scale for the study area. These data were used to calibrate the spatial distribution of the surface temperature when using remote sensing images from MODIS (Moderate Resolution Imaging Spectradiometer). Surface temperatures were estimated using the land surface temperature product MODII-L2 distributed by the Land Process Distributed Active Archive Center(LP DAAC). These results show the maximum, minimum and average temperatures in San Juan and in the entire Island at a resolution of 1 km. The information retrieved from MODIS for land surface temperatures reflected similar temporal and spatial variations as the weather stations and ATLAS measurements with a highest absolute offset of about 5 C due to the differences between surface and air temperatures.

Gonzalez, Jorge E.↗
NASA NTRS1984

Flow structure within a heated rectangular jet ejector

Preliminary results of an experimental study of the flow field structure within a rectangular jet ejector are presented. The tests determined the effect of primary jet heating and ejector duct width on the flow field at a fixed jet exit Mach number of 0.3. For comparison the rectangular jet without the presence of the ejector shroud was also studied. Measurements of the mean velocity field, total temperature field, and ejector shroud surface pressure distribution, along with schlieren flow visualization, were made. It was found that: the ejector did not enhance centerline temperature decay in comparison to the free jet; the presence of the ejector shroud significantly reduced jet growth; and, the ejector centerline velocity/temperature decay was not sensitive to duct width variations.

Mclachlan, B. G.↗
DOE OSTI2025

Investigation of N 2 /O 2 plasma interaction with Pt-catalyst: effect of metastable adsorbates on product hysteresis

The coupling of catalysts and atmospheric-pressure plasma has the potential to improve the efficiency of certain catalytic reactions. Understanding the changes that the catalyst surface undergoes during exposure to plasma is key to improving plasma–catalytic performance. In this work, long term exposure of Pt–Al 2 O 3 powder catalyst to an Ar/N 2 /O 2 non-equilibrium atmospheric-pressure plasma-jet was investigated. Products produced by the interaction were analyzed downstream with Fourier-transform infrared spectroscopy while surface species were analyzed operandi with diffuse reflectance infrared Fourier transform spectroscopy. During exposure, the catalyst temperature was ramped cyclically between 100 °C and 350 °C to understand how substrate temperature affects the plasma–catalyst interaction. Long-lasting changes were revealed to take place on the catalyst surface during plasma exposure. At low temperatures, Pt–O and Pt–NO accumulate on the surface which react at elevated temperatures to form NO 2 . NO 2 initially appears to spill on to the Al 2 O 3 support as nitrites and nitrates instead of desorbing. Stable surface conditions are only achieved after prolonged plasma exposure, when nitrate sites on the Al 2 O 3 support are filled. By changing the catalyst temperature at various rates, the impact of total plasma species flux to the surface was analyzed. It was found that decreasing the heating rate increased the hysteresis in the pattern of NO 2 formation during thermal cycling. The variation with temperature demonstrates that plasma exposure results in a buildup of surface NO x and oxygen species which react or desorb at high temperatures. The observed changes are discussed from the generic viewpoint that a non-equilibrium plasma interacting with a catalyst at low temperature introduces metastable steady-state surface conditions. Upon heating above a threshold temperature, the introduced surface modifications can change either due to thermal effects, or, for a plasma environment, by additional interaction with the incident plasma species flux. The surface/material changes take place in a highly predictable fashion and after sufficient time above the threshold temperature reach a steady-state condition that is different from the transient behavior that is observed during initial heating. During cooling the plasma-surface interaction exhibits a different behavior than during heating, and this results in hysteresis of diverse observables. The metastability/hysteresis description appears quite generic and analogous to hysteresis behavior seen for different systems. Furthermore, it is expected to be useful for understanding the consequences of plasma–catalyst surface interactions for various systems.

36 MATERIALS SCIENCE↗
NASA NTRS2004

Durability of Environmental Barrier Coatings in a Water Vapor/Oxygen Environment

Silicon carbide (Sic) and silicon nitride (Si3N4) show potential for application in the hot sections of advanced jet engines. The oxidation behavior of these materials has been studied in great detail. In a pure oxygen environment, a silica (SiO2) layer forms on the surface and provides protection from further oxidation. Initial oxidation is rapid, but slows as silica layer grows; this is known as parabolic oxidation. When exposed to model fuel-lean combustion applications (standard in jet engines), wherein the partial pressure of water vapor is approximately 0.5 atm., these materials exhibit different characteristics. In such an environment, the primary oxidant to form silica is water vapor. At the same time, water vapor reacts with the surface oxide to form gaseous silicon hydroxide (Si(OH)4). The simultaneous formation of both silica and Si(OH)4 -the latter which is lost to the atmosphere- the material continues to recede. Recession rates for uncoated Sic and Si3N4 are unacceptably high, for use in jet engines, - on the order of 1mm/4000h. External coatings have been developed that protect Si-based materials from water vapor attack. One such coating consists of a Ba(0.75)Sr(0.25)Al2Si2O8 (BSAS) topcoat, a mullite/BSAS intermediate layer and a Si bond coat. The key function of the topcoat is to protect the Si-base material from water vapor; therefore it must be fairly stable in water vapor (recession rate of about 1mm/40,000h) and remain crack free. Although BSAS is much more resistant to water vapor attack than pure silica, it exhibits a linear weight loss in 50% H2O - 50% O2 at 1500 C. The objective of my research is to determine the oxidation behavior of a number of alternate hot-pressed monolithic top coat candidates. Potential coatings were exposed at 1500 C to a 50% H2O - 50% O2 gas mixture flowing at 4.4 cm/s . These included rare- earth silicates, barium-strontium aluminosilicates. When weight changes were measured with a continuously recording microbalance, linear weight loss was observed. BSAS materials have a fairly high volatility at this temperature, but rare-earth mono-silicate compounds were significantly more stable.

Holchin, John E.↗
NASA NTRSDate not supplied

Material Response Analysis of PICA-NuSil at the Hypersonic Materials Environmental Test System

Phenolic impregnated carbon ablator (PICA) is a thermal protection system (TPS) that gained heritage during the Stardust mission and is the baseline TPS material for expeditions to Mars (e.g., Mars Science Laboratory and Mars 2020).1 PICA is friable; therefore, a polysiloxane resin (NuSil CV-1144-0) is deposited onto the surface of flight hardware before assembly, test, and launch operations (ATLO) to mitigate particle shedding. Furthermore, the Mars Science Laboratory (MSL) and Mars 2020 heatshields were instrumented with an array of thermocouple plugs (MEDLI Integrated Sensor Plugs or MISP) designed to measure the in-depth thermal response of PICA during flight. Post-flight analysis of MISP data suggests that recession was lower than predicted, and NuSil is suspected as a reasonable cause. NuSil primarily consists of a copolymer blend of dimethyl and diphenyl-substituted polysiloxane resin. Four decades of research in the field of polymer-derived ceramics demonstrate that polysiloxane resins form oxidation-resistant silicon oxycarbide materials at pyrolysis temperatures as low as 800 °C. -2 Furthermore, silicon oxycarbide materials exhibit excellent thermal stability at relatively high-temperatures (< 1200 °C) but eventually decompose via carbothermal reduction. -3 Therefore, it is reasonable to suggest that NuSil forms an oxidation-resistant thermal barrier coating on the TPS surface and influences the material response during atmospheric entry. Evidence for this notion was observed during prior arc-jet testing at both the Aerodynamic Heating Facility (AHF) and the Panel Test Facility (PTF) at the NASA Ames Research Center. Articles of PICA were subjected to testing in airflow, and a temperature discontinuity was recorded at the surface of coupons coated with NuSil. A glassy coating was observed to form at the surface in shear flow configurations (wedge and panel) under moderate heat fluxes. Furthermore, state-of-the-art material response models have yet to account for the underlying physics and chemistry of the temperature discontinuity. To this end, a pathfinder test campaign was executed at the Hypersonic Materials Environmental Test System (HyMETS) to enhance the fundamental understanding of PICA-NuSil ablation phenomena and provide a preliminary data set to aid in the development of material response models.

PICA↗
NASA NTRS1992

Assessment of Potential Aerodynamic Benefits from Spanwise Blowing at the Wing Tip

A comprehensive set of experimental and analytical investigations have been conducted to assess the potential aerodynamic benefits from spanwise blowing at the tip of a moderate aspect ratio, swept wing. An analytical model has been developed to simulate a jet exhausting from the wing tip. An experimental study of a subsonic jet exhausting from the wing tip was conducted to investigate the effect of spanwise blowing from the tip on the aerodynamic characteristics of a moderate aspect ratio, swept wing. Wing force and moment data and surface pressure data were measured at Mach numbers up to 0.72. Results indicate that small amounts of blowing from small jets increase the lift curve slope a small amount, but have no effect on drag. Larger amounts of blowing from longer jets blowing increases lift near the tip and reduce drag at low Mach numbers. These benefits decrease with increasing Mach number, and vanish at Mach 0.5. A Navier-Stokes solver with modified boundary conditions at the tip was used to extrapolate the results to a Mach number of 0.72. With current technology and conventional wing shapes, spanwise blowing at the wing tip does not appear to be a practical means of reducing drag of moderate aspect ratio wings at high subsonic Mach numbers.

Mineck, Raymond Edward↗
NASA NTRS2002

Laminar Soot Processes (LSP)

This is the final report of a research program considering the structure and the soot surface reaction properties of laminar nonpremixed (diffusion) flames. The study was limited to ground-based measurements of buoyant laminar jet diffusion flames at pressures of 0.1-1.0 atm. The motivation for the research is that soot formation in flames is a major unresolved problem of combustion science that influences the pollutant emissions, durability and performance of power and propulsion systems, as well as the potential for developing computational combustion. The investigation was divided into two phases considering the structure of laminar soot-containing diffusion flames and the soot surface reaction properties (soot surface growth and oxidation) of these flames, in turn. The first phase of the research addressed flame and soot structure properties of buoyant laminar jet diffusion flames at various pressures. The measurements showed that H, OH and O radical concentrations were generally in superequilibrium concentrations at atmospheric pressure but tended toward subequilibrium concentrations as pressures decreased. The measurements indicated that the original fuel decomposed into more robust compounds at elevated temperatures, such as acetylene (unless the original fuel was acetylene) and H, which are the major reactants for soot surface growth, and that the main effect of the parent fuel on soot surface growth involved its yield of acetylene and H for present test conditions. The second phase of the research addressed soot surface reaction properties, e.g., soot surface growth and surface oxidation. It was found that soot surface growth rates in both laminar premixed and diffusion flames were in good agreement, that these rates were relatively independent of fuel type, and that these rates could be correlated by the Hydrogen-Abstraction/Carbon-Addition (HACA) mechanisms of Colket and Hall (1994), Frenklach et al. (1990,1994), and Kazakov et al. (1995). It was also found that soot surface oxidation rates were relatively independent of fuel type, were not correlated with O2, CO2, H2O and O collision rates but were correlated with the collision rates of OH with a collision efficiency of 0.14, in agreement with the early measurements in premixed flames of Neoh et al. (1980), after allowing for oxidation by O2 via the classical rate expression of Nagle and Strickland-Constable (1962).

Dai, Z.↗