Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ISOTHERMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Hydrocarbon Effect on a Fe-zeolite Urea-SCR Catalyst: An Experimental and Modeling Study

Synergies between various catalytic converters such as SCR and DPF are vital to the success of an integrated aftertreatment system for simultaneous NOx and particulate matter control in diesel engines. Several issues such as hydrocarbon poisoning, thermal aging and other coupled aftertreatment dynamics need to be addressed to develop an effective emission control system. This paper reports an experimental and modeling study to understand the effect of hydrocarbons on a Fe-zeolite urea-SCR bench reactor. Several bench-reactor tests to understand the inhibition of NOx oxidation, to characterize hydrocarbon storage and to investigate the impact of hydrocarbons on SCR reactions were conducted. Toluene was chosen as a representative hydrocarbon in diesel exhaust and various tests using toluene reveal its inhibition of NO oxidation at low temperatures and its oxidation to CO and CO2 at high temperatures. Surface isotherm tests were conducted to characterize the adsorption-desorption equilibrium of toluene through Langmuir isotherms. Using the rate parameters, a toluene storage model was developed and validated in simulation. With toluene in the stream, controlled SCR tests were run on the reactor and performance metrics such as NOx conversion and NH3 slip were compared to a set of previously run tests with no toluene in the stream. Tests indicate a significant effect of toluene on NOx and NH3 conversion efficiencies even at temperatures greater than 300oC. A kinetic model to address the toluene inhibition during NO oxidation reaction was developed and is reported in the paper. This work is significant especially in an integrated DPF-SCR aftertreatment scenario where the SCR catalyst on the filter substrate is exposed to un-burnt diesel hydrocarbons during active regeneration of the particulate filter.

33 ADVANCED PROPULSION SYSTEMS↗

A trust-region algorithm for the optimization of PSA processes using reduced-order modeling

The last few decades have seen a considerable increase in the applications of adsorptive gas separation technologies, such as pressure swing adsorption (PSA); the applications range from bulk separations to trace contaminant removal. PSA processes are based on solid-gas equilibrium and operate under periodic transient conditions [1]. Bed models for these processes are therefore defined by coupled nonlinear partial differential and algebraic equations (PDAEs) distributed in space and time with periodic boundary conditions that connect the processing steps together and high nonlinearities arising from non-isothermal effects and nonlinear adsorption isotherms. As a result, the optimization of such systems for either design or operation represents a significant computational challenge to current nonlinear programming algorithms. Model reduction is a powerful methodology that permits systematic generation of cost-efficient low-order representations of large-scale systems that result from discretization of such PDAEs. In particular, low-dimensional approximations can be obtained from reduced order modeling (ROM) techniques based on proper orthogonal decomposition (POD) and can be used as surrogate models in the optimization problems. In this approach, a representative ensemble of solutions of the dynamic PDAE system is constructed by solving a higher-order discretization of the model using the method of lines, followed by the application of Karhunen-Loeve expansion to derive a small set of empirical eigenfunctions (POD modes). These modes are used as basis functions within a Galerkin's projection framework to derive a low-order DAE system that accurately describes the dominant dynamics of the PDAE system. This approach leads to a DAE system of significantly lower order, thus replacing the one obtained from spatial discretization before and making optimization problem computationally efficient [2]. The ROM methodology has been successfully applied to a 2-bed 4-step PSA process used for separating a hydrogen-methane mixture in [3]. The reduced order model developed was successfully used to optimize this process to maximize hydrogen recovery within a trust-region. We extend this approach in this work to develop a rigorous trust-region algorithm for ROM-based optimization of PSA processes. The trust-region update rules and sufficient decrease condition for the objective is used to determine the size of the trust-region. Based on the decrease in the objective function and error in the ROM, a ROM updation strategy is designed [4, 5]. The inequalities and bounds are handled in the algorithm using exact penalty formulation, and a non-smooth trust-region algorithm by Conn et al. [6] is used to handle non-differentiability. To ensure that the first order consistency condition is met and the optimum obtained from ROM-based optimization corresponds to the optimum of the original problem, a scaling function, such as one proposed by Alexandrov et al. [7], is incorporated in the objective function. Such error control mechanism is also capable of handling numerical inconsistencies such as unphysical oscillations in the state variable profiles. The proposed methodology is applied to optimize a PSA process to concentrate CO{sub 2} from a nitrogen-carbon dioxide mixture. As in [3], separate ROMs are developed for each operating step with different POD modes for each state variable. Numerical results will be presented for optimization case studies which involve maximizing CO{sub 2} recovery, feed throughput or minimizing overall power consumption.

97 MATHEMATICS AND COMPUTING↗

Investigation of the carbon dioxide sorption capacity and structural deformation of coal

Due to increasing atmospheric CO2 concentrations causing the global energy and environmental crises, geological sequestration of carbon dioxide is now being actively considered as an attractive option to mitigate greenhouse gas emissions. One of the important strategies is to use deep unminable coal seams, for those generally contain significant quantities of coal bed methane that can be recovered by CO2 injection through enhanced coal bed natural gas production, as a method to safely store CO2. It has been well known that the adsorbing CO2 molecules introduce structural deformation, such as distortion, shrinkage, or swelling, of the adsorbent of coal organic matrix. The accurate investigations of CO2 sorption capacity as well as of adsorption behavior need to be performed under the conditions that coals deform. The U.S. Department of Energy-National Energy Technology Laboratory and Regional University Alliance are conducting carbon dioxide sorption isotherm experiments by using manometric analysis method for estimation of CO2 sorption capacity of various coal samples and are constructing a gravimetric apparatus which has a visual window cell. The gravimetric apparatus improves the accuracy of carbon dioxide sorption capacity and provides feasibility for the observation of structural deformation of coal sample while carbon dioxide molecules interact with coal organic matrix. The CO2 sorption isotherm measurements have been conducted for moist and dried samples of the Central Appalachian Basin (Russell County, VA) coal seam, received from the SECARB partnership, at the temperature of 55 C.

01 COAL, LIGNITE, AND PEAT↗

pi-Selective stationary phases: (II) Adsorption behavior of substituted aromatic compounds on n-alkyl-phenyl stationary phases

The frontal analysis method was used to measure the adsorption isotherms of phenol, 4-chlorophenol, p-cresol, 4-methoxyphenol and caffeine on a series of columns packed with home-made alkyl-phenyl bonded silica particles. These ligands consist of a phenyl ring tethered to the silica support via a carbon chain of length ranging from 0 to 4 atoms. The adsorption isotherm models that fit best to the data account for solute-solute interactions that are likely caused by p-p interactions occurring between aromatic compounds and the phenyl group of the ligand. These interactions are the dominant factor responsible for the separation of low molecular weight aromatic compounds on these phenyl-type stationary phases. The saturation capacities depend on whether the spacer of the ligands have an even or an odd number of carbon atoms, with the even alkyl chain lengths having a greater saturation capacity than the odd alkyl chain lengths. The trends in the adsorption equilibrium constant are also significantly different for the even and the odd chain length ligands.

36 MATERIALS SCIENCE↗

The High-Pressure Characterization of Energetic Materials: 2-Methyl-5-Nitramino-2H-Tetrazole

The isothermal structural properties, equation of state, and vibrational dynamics of 2MNT were studied under high-pressure using synchrotron XRD and optical Raman and IR microspectroscopy. Analysis of the XRD patterns revealed no indication of a phase transition to near 15 GPa and the pressure-volume isotherm remained smooth to 15 GPa. Near 15 GPa, significant sample damage was observed from the X-ray beam which precluded the acquisition of patterns above this pressure. XRD and Raman spectroscopic measurements showed the monoclinic ambient condition phase of 2MNT remains the dominant phase to near 20 GPa, although a shift of the NO{sub 2} IR active vibrational modes to lower frequencies suggested a subtle geometry modification not reflected in the XRD data.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Experimental evidence of a delta-shock in nonlinear chromatography

We report about a new type of composition front in nonlinear chromatography that is called delta-shock, which has to be added to the family of classical transitions, i.e. simple waves, shocks and semi-shocks. Recently, the occurrence of delta-shocks in the case of mixed competitive-cooperative isotherms of the following type n{sub i} = H{sub i}c{sub i}/1 = K{sub 1}c{sub 1} + K{sub 2}c{sub 2} (i = 1,2), (with H{sub 2} > H{sub 1}, where components 1 and 2 have anti-Langmuir and Langmuir adsorption behavior, respectively) was predicted theoretically and their behavior was analyzed in the frame of the equilibrium theory of chromatography. The delta-shock can be viewed as a growing traveling spike superimposed to the discontinuity separating the initial and the feed state, which propagates along the column at constant speed and constant rate of growth. In this work we complement these findings from an experimental point of view. The binary system consisting of phenetole (component 1) and 4-tert-butylphenol (component 2) in methanol-water (about 2:1, v/v) on a Zorbax 300StableBond-C18 column from Agilent has been shown, through a series of overloaded pulse experiments and of frontal analysis experiments with the pure compounds, to be subject to the competitive-cooperative isotherm of the type above, up to rather large concentrations. This system does exhibit adelta-shock when the operating conditions are chosen according to theory, namely when phenetole initially saturating the column is displaced by 4-tert-butylphenol, both at high concentrations (the minimum concentrations exhibiting a fully developed delta-shock in this series of experiments were c{sub 1} = 20 g/L and c{sub 2} = 75 g/L). The propagation of the delta-shock matches the theoretical predictions in terms of both the effect of concentration and the effect of column length. This is the first experimental observation ever of adelta-shock in chromatography. It is noteworthy that the proof of the occurrence of the delta-shock reported here has been obtained in both laboratories cooperating in this project.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Study of an unrefined humate solution as a possible remediation method for groundwater contamination - 15698

Savannah River Site (SRS) was one of the major nuclear processing facilities in the U.S. where plutonium was produced during the Cold War. Approximately 1.8 billion gallons of low level acidic waste solution containing radionuclides and dissolved metals were discharged to a series of unlined seepage basins at the F/H Area. Uranium is a key contaminant of concern in the basin's groundwater. It is migrating into the groundwater creating an acidic plume with a pH between 3-5.5. Groundwater Actions: The pump-and-treat water treatment unit was designed and built in 1997 to remove metals and radionuclides. In 2004 a hybrid funnel-and-gate system was constructed to create a treatment zone in which the acidic nature of the contaminated sediments could be reversed. Huma-K is an organic fertilizer that comes from the alkaline extraction of leonardite (a low-rank coal). Huma-K has a high content of humic substances which consist of complex organic compounds formed by the decomposition of plant and animal tissue. The objective of this study is to determine if a low cost unrefined humate solution (Huma-K) can be used to facilitate uranium adsorption to control its mobility in acidic groundwater. This study can assist in evaluating whether Huma-K can be used as an in situ amendment for the remediation of groundwater contaminated with uranium. Sediments from FAW-1 70-90 ft were used in this experiment. Sediments were disaggregated and sieved to a particle size of . 2 mm. Concentrations in the range 10-500 ppm were tested. Once all the components were added, pH was adjusted to 4. Samples were vortex mixed and placed on a shaker table at 100 RPM for a period of 24 hours in order to reach the adsorption equilibrium. Once the adsorption equilibrate was reached, samples were centrifuged at 2700 RPM to separate the liquid and the solid phase. The liquid fraction was analyzed using a Thermo Scientific Genesys 10S UV-Vis spectrophotometer. The same experimental design was used as explained above. A known concentration of Huma-K was used to study the pH effect on the sorption process. pH values were measured at the beginning and at the end of the experiment. Spectra of Huma-K show a featureless character. Absorbance of light increases as the wavelength is decreased. Measurements were done at 254 nm due to the presence of aromatic rings. Apparently there are two sorption processes. The first one follows the same trend as the Langmuir isotherm up to 250 ppm. The second sorption process occurs after all the binding sites in the sediments have been occupied. Precipitation decreases as the pH is increased. Based on the sorption isotherm, humic substances apparently bind first to the binding sites of the sediments particles. Once all the binding sites have been occupied, other sorption processes may start to dominate. Sorption is affected by pH. Higher sorption is seen at low pH values. Increased precipitation at low pH values is probably due to the neutralization of surface charges of humic molecules making them agglomerate.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Isopiestic Measurements of Water Adsorption on Uranium Bearing Solids - 1900w

The research focus was to investigate the stability of the multicomponent uranium-bearing precipitates mimicking those created in sediments as a result of alkaline ammonia gas treatment in the vadose zone. Gravimetric measurements of moisture uptake on uranium-bearing precipitates as a function of increasing relative humidity can provide reasonable estimates of the deliquescence point of solid phases or its components. Water moisture uptake by uranium-bearing precipitates as a function of increasing relative humidity was measured at 25 deg. C via the isopiestic method. The conditions for each isotherm were calculated by a division of the amount of adsorbed moisture by the amount of dry precipitate samples. This method can provide estimates of water quantity retained within precipitates conducted in the range of water activities. The desorption portion of the isotherm was obtained by progressively decreasing the water activity or relative pressure in the isopiestic chamber while monitoring the equilibrium amount of moisture sorbed at each relative pressure. The amount of water adsorbed by multicomponent precipitates at a{sub w} = 0.67 ranged between 0.63 and 0.77 g water/g precipitate. Higher water activities or relative humidity values eventually lead to the deliquescence of the solid or its components and the formation of a liquid phase. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Observation of off-Hugoniot shocked states with ultrafast time resolution

We apply ultrafast single shot interferometry to determine the pressure and density of argon shocked from up to 7.8 GPa static initial pressure in a diamond anvil cell. This method enables the observation of thermodynamic states distinct from those observed in either single shock or isothermal compression experiments, and the observation of ultrafast dynamics in shocked materials. We also present a straightforward method for interpreting ultrafast shock wave data which determines the index of refraction at the shock front, and the particle and shock velocities for shock waves in transparent materials. Based on these methods, we observe shocked thermodynamic states between the room temperature isotherm of argon and the shock adiabat of cryogenic argon at final shock pressures up to 28 GPa.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Postshock Thermally Induced Transformations in Experimentally Shocked Magnetite

We studied the effect of 973 K heating in argon atmosphere on the magnetic and structural properties of a magnetite-bearing ore, which was previously exposed to laboratory shock waves between 5 and 30 GPa. For this purpose magnetic properties were studied using temperature-dependent magnetic susceptibility, magnetic hysteresis and low-temperature saturation isothermal remanent magnetization. Structural properties of magnetite were analyzed using X-ray diffraction, high-resolution scanning electron microscopy and synchrotron-assisted X-ray absorption spectroscopy. The shock-induced changes include magnetic domain size reduction due to brittle and ductile deformation features and an increase in Verwey transition temperature due to lattice distortion. After heating, the crystal lattice is relaxed and apparent crystallite size is increased suggesting a recovery of lattice defects documented by a mosaic recrystallization texture. The structural changes correlate with modifications in magnetic domain state recorded by temperature-dependent magnetic susceptibility, hysteresis properties and low-temperature saturation isothermal remanent magnetization. In conclusion, these alterations in both, magnetic and structural properties of magnetite can be used to assess impact-related magnetic anomalies in impact structures with a high temperature overprint.

58 GEOSCIENCES↗

THE EFFECT OF TEMPERATURE AND UNIAXIAL PRESSURE ON THE DENSIFICATION BEHAVIOR OF SILICA AEROGEL GRANULES

Materials are being developed in U.S. for the removal and immobilization of iodine from gaseous products of nuclear fuel reprocessing in support of the Fuel Cycle Technology Separations and Waste Forms Campaign. The silver-functionalized silica aerogel proved to be an excellent candidate for this treatment because of its high selectivity and sorption capacity for radioiodine and its possible conversion to a durable silica-based waste form. The present study investigated with nitrogen sorption and helium pycnometry the effect of pressureless isothermal sintering at temperatures of 900-1400°C for 2.5-90 min or isothermal hot-pressing at 1200°C for 2.5 min on densification of raw and silver-functionalized silica aerogel granules. Rapid sintering was observed at 1050 and 1200°C. Only 15 min of pressureless sintering at 1200°C resulted in almost complete densification. The macropores disappeared, surface area decreased from 1114 m2/g to 25 m2/g, pore volume from 7.41 cm3/g to 0.09 cm3/g, and adsorption pore size from 18.7 to 7 nm. The skeletal density of sintered granules was similar to the bulk density of amorphous silica (2.2 g/cm3). The hot-pressing accelerated the sintering process, decreasing significantly the pore size and volume.

BET↗

Thermally Activated Martensite: Its Relationship to Non-Thermally Activated (Athermal) Martensite

The classification of martensitic displacive transformations into athermal, isothermal or anisothermal is discussed. Athermal does not mean 'no temperature dependence' as is often thought, but is best considered to be short for the notion of no thermal activation. Processes with no thermal activation do not depend on time, as there is no need to wait for sufficient statistical fluctuations in some specific order parameter to overcome an activation barrier to initiate the process. Clearly, this kind of process contrasts with those that are thermally activated. In the literature, thermally activated martensites are usually termed isothermal martensites, suggesting a constant temperature. Actually such martensites also typically occur with continuous cooling. The important distinctive feature of these martensites is that they are thermally activated and hence are distinguishable in principle from athermal martensites. A third type of process, anisothermal, has been introduced to account for those transformations which are thought to be thermally activated but which occur on continuous cooling. They may occur so rapidly that they do not appear to have an incubation time, and hence could be mistakenly called an athermal transformation. These designations will be reviewed and discussed in terms of activation energies and kinetic processes of the various martensitic transformations.

36 MATERIALS SCIENCE↗

Transforming an Ionic Conductor into an Electronic Conductor via Crystallization: In Situ Evolution of Transference Numbers and Structure in (La,Sr)(Ga,Fe)O 3–x Perovskite Thin Films

Mixed-conducting perovskites are workhorse electrochemically active materials, but typical high-temperature processing compromises their catalytic activity and chemo-mechanical integrity. Low-temperature pulsed laser deposition of amorphous films plus mild thermal annealing is an emerging route to form homogeneous mixed conductors with exceptional catalytic activity, but little is known about the evolution of the oxide-ion transport and transference numbers during crystallization. Here the coupled evolution of ionic and electronic transport behavior and structure in room-temperature-grown amorphous (La,Sr)(Ga,Fe)O 3-x films as they crystallize is explored. In situ ac-impedance spectroscopy with and without blocking electrodes, simultaneous capturing-synchrotron-grazing-incidence X-ray diffraction, dc polarization, transmission electron microscopy, and molecular dynamics simulations to evaluate isothermal and non-isothermal crystallization effects and the role of grain boundaries on transference numbers is combined. Ionic conductivity increases by ≈2 orders of magnitude during crystallization, with even larger increases in electronic conductivity. Consequently, as crystallinity increases, LSGF transitions from a predominantly ionic conductor to a predominantly electronic conductor. The roles of evolving lattice structural order, microstructure, and defect chemistry are examined. Grain boundaries appear relatively nonblocking electronically but significantly blocking ionically. The results demonstrate that ionic transference numbers can be tailored over a wide range by tuning crystallinity and microstructure without having to change the cation composition.

36 MATERIALS SCIENCE↗

How Reproducible are Surface Areas Calculated from the BET Equation?

Abstract Porosity and surface area analysis play a prominent role in modern materials science. At the heart of this sits the Brunauer–Emmett–Teller (BET) theory, which has been a remarkably successful contribution to the field of materials science. The BET method was developed in the 1930s for open surfaces but is now the most widely used metric for the estimation of surface areas of micro‐ and mesoporous materials. Despite its widespread use, the calculation of BET surface areas causes a spread in reported areas, resulting in reproducibility problems in both academia and industry. To prove this, for this analysis, 18 already‐measured raw adsorption isotherms were provided to sixty‐one labs, who were asked to calculate the corresponding BET areas. This round‐robin exercise resulted in a wide range of values. Here, the reproducibility of BET area determination from identical isotherms is demonstrated to be a largely ignored issue, raising critical concerns over the reliability of reported BET areas. To solve this major issue, a new computational approach to accurately and systematically determine the BET area of nanoporous materials is developed. The software, called “BET surface identification” (BETSI), expands on the well‐known Rouquerol criteria and makes an unambiguous BET area assignment possible.

36 MATERIALS SCIENCE↗

Thermal Dynamics and Lithium Plating Detection in High‐Power Li‐Ion Batteries for eVTOL Applications

The rapid electrification of aerial transportation is driving the need for high‐performance Li‐ion batteries that can operate reliably under stringent thermal and safety constraints. The unique mission profile of electric Vertical Take‐off and Landing (eVTOL) aircraft necessitates a focused investigation into the thermal behavior and safety characteristics of these batteries. Here, in this study, operando isothermal microcalorimetry is employed to examine the thermal evolution of Li‐ion batteries under cycling conditions representative of eVTOL operations. These findings reveal that high‐power discharge events—such as those during take‐off and landing—shift the thermal response toward exothermic behavior, in contrast to the typically endothermic response expected under near‐equilibrium cycling conditions. Additionally, the results suggest that advanced electrolyte formulations may help suppress excess heat generation, thereby improving battery safety. Notably, the calorimetric results exhibit a distinct thermal signature associated with lithium plating, offering a potential diagnostic for detecting Li plating during eVTOL operation. Overall, this study demonstrates the utility of isothermal microcalorimetry as a valuable tool for assessing thermal risks in Li‐ion batteries for eVTOL applications, and highlights the importance of targeted design strategies to mitigate safety hazards during high‐power demand scenarios.

Li plating↗

Sulfonyl PIM–1: A diverse separation membrane with dilation resistance

A sulfone modified variant (soPIM–1) of the first polymer of intrinsic microporosity has been studied through molecular simulations to analyze its applicability for adsorption–based separations of diverse nonpolar, quadrupolar, and dipolar adsorbate species. Single component gas phase adsorption isotherms of each adsorbate are provided. Here, the adsorptive properties of soPIM–1 are reported from the application of two methods: (a) traditional grand canonical Monte Carlo (GCMC) simulations and (b) a combination of Monte Carlo and molecular dynamics (GCMC/MD) techniques, which accounts for sorption–induced polymer dynamics. The calculated isosteric heats of adsorption are compared to those from the parent PIM–1 structure and reveals increased CO2 affinity with relatively no change in hydrocarbon affinity. Moreover, to quantify soPIM–1's resistance to dilation the evolution of the microporous structure across the adsorption isotherm loading pressures has been evaluated. Relatedly, nonequilibrium MD simulations have been utilized to determine that soPIM–1 is approximately twice as stiff as PIM–1.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Porous Covalent Organic Polymers for Efficient Fluorocarbon‐Based Adsorption Cooling

Abstract Adsorption‐based cooling is an energy‐efficient renewable‐energy technology that can be driven using low‐grade industrial waste heat and/or solar heat. Here, we report the first exploration of fluorocarbon adsorption using porous covalent organic polymers (COPs) for this cooling application. High fluorocarbon R134a equilibrium capacities and unique overall linear‐shaped isotherms are revealed for the materials, namely COP‐2 and COP‐3. The key role of mesoporous defects on this unusual adsorption behavior was demonstrated by molecular simulations based on atomistic defect‐containing models built for both porous COPs. Analysis of simulated R134a adsorption isotherms for various defect‐containing atomistic models of the COPs shows a direct correlation between higher fluorocarbon adsorption capacities and increasing pore volumes induced by defects. Combined with their high porosities, excellent reversibility, fast kinetics, and large operating window, these defect‐containing porous COPs are promising for adsorption‐based cooling applications.

Zheng, Jian↗

Porous Covalent Organic Polymers for efficient Fluorocarbon-based Adsorption Cooling

Adsorption-based cooling is an energy-efficient renewable-energy technology that can be driven using low-grade industrial waste heat and/or solar heat. Here, we report the first exploration of fluorocarbon adsorption using porous covalent organic polymers (COPs) for this cooling application. High fluorocarbon R134a equilibrium capacities and unique overall linear-shaped isotherms are revealed for the materials, namely COP-2 and COP-3. The key role of mesoporous defects on this unusual adsorption behavior was demonstrated by molecular simulations based on atomistic defect-containing models built for both porous COPs. Analysis of simulated R134a adsorption isotherms for various defect-containing atomistic models of the COPs shows a direct correlation between higher fluorocarbon adsorption capacities and increasing pore volumes induced by defects. Combined with their high porosities, excellent reversibility, fast kinetics, and large operating window, these defect-containing porous COPs are promising for adsorption-based cooling applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗