Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Drag coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Theoretical span loading and moments of tapered wings produced by aileron deflection

The effect of tapered ailerons on linearly tapered wings is theoretically determined. Four different aileron spans are considered for each of three wing aspect ratios and each of four wing taper ratios. The change in lift on one half of the wing, the rolling moment, the additional induced drag, and the yawing moment, due to aileron deflection, are represented by non dimensional coefficients. Similar coefficients are given for the damping and yawing moments, the additional drag, and the change in lift, due to rolling. It was found possible to effect a fairly close agreement between the theoretical and experimental rolling moments by introducing into the theoretical expression for the rolling moment an effective change in angle of attack obtained from an analysis of flap data. The theoretical curves show that the highly tapered wing with long ailerons has a lower ratio of yawing to rolling moment and a lower additional induced drag than wings with less taper.

Pearson, H A↗

Aeroelastic Trim Drag Optimization of Mach 0.8 Transonic Truss-Braced Wing Aircraft using High-Lift Devices and Control Surfaces

This paper presents an aeroelastic trim drag optimization study of the Mach 0.8 Transonic Truss-Braced Wing (TTBW) aircraft using the High-lift devices and control surfaces. An aero-structural analysis solver VSPAERO with transonic small disturbance, integral boundary-layer, and wing-strut interference corrections coupled to mode shapes computed by NASTRAN using the Galerkin method is developed to provide a rapid aircraft aeroelastic performance evaluation. Three different flight conditions corresponding to Mach 0.8 are selected for the aeroelastic trim drag optimization at the design and off-design cruise lift coefficients. The preliminary optimization results show that the TTBW aircraft with the optimized deflection of the high-lift devices and control surfaces achieves a drag reduction of about 8.2 counts, 6.5 counts, and 9.7 counts corresponding to the lift coefficients 0.661, 0.695, and 0.729, respectively. A high-fidelity CFD solver FUN3D is used to verify the aeroelastic trim drag optimization.

TTBW↗

Effect of artificial viscosity on shocked particle-laden flows for staggered grid Lagrangian methods

Abstract Shocked particle-laden flows are important to many natural and industrial processes. When simulating these systems, artificial viscosity is often required to prevent numerical artifacts, such as ringing, from arising in the pressure and density fields. The linear and quadratic coefficients of the artificial viscosity determine the amount of smoothing that occurs in these fields. For particle-laden flows, however, many of the fluid–particle interaction forces, for example, the pressure gradient force and unsteady forces, depend on gradients in the fluid fields. Furthermore, while the shock passes over a particle, these forces can be more dominant than drag. This means that the artificial viscosity coefficients affect how a particle and fluid interact when simulating shocked particle systems. Here this effect is investigated for isolated particles and for a particle curtain using a staggered grid Lagrangian approach. The artificial viscosity coefficients have a significant impact on the maximum force that a fluid imparts to a particle, which is important for determining whether a particle will break up in response to the shock. Furthermore, it is found that the density ratio between the particle and the fluid is important in determining whether the artificial viscosity coefficients have a significant impact on the particle’s motion.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An analysis of the high-latitude thermospheric wind pattern calculated by a thermospheric general circulation model. I - Momentum forcing

A diagnostic processor (DP) was developed for analysis of hydrodynamic and thermodynamic processes predicted by the NCAR thermospheric general circulation model (TGCM). The TGCM contains a history file on the projected wind, temperature and composition fields at each grid point for each hour of universal time. The DP assimilates the history file plus ion drag tensors and drift velocities, specific heats, coefficients of viscosity, and thermal conductivity and calculates the individual forcing terms for the momentum and energy equations for a given altitude. Sample momentum forcings were calculated for high latitudes in the presence of forcing by solar radiation and magnetospheric convection with a 60 kV cross-tail potential, i.e., conditions on Oct. 21, 1981. It was found that ion drag and pressure forces balance out at F region heights where ion drift velocities are small. The magnetic polar cap/auroral zone boundary featured the largest residual force or net acceleration. Diurnal oscillations were detected in the thermospheric convection, and geostrophic balance was dominant in the E layer.

Killeen, T. L.↗

Effects at Mach Numbers of 1.61 and 2.01 of Camber and Twist on the Aerodynamic Characteristics of Three Swept Wings Having the Same Planform

An investigation has been made at Mach numbers of 1.61 and 2.01 to determine the aerodynamic characteristics of three wings having a sweepback of 50 deg at the quarter-chord line, a taper ratio of 0.20, an NACA 65A005 thickness distribution, and an aspect ratio of 3.5. One wing was flat, one had at each spanwise station an a = 0 mean line modified to have a maximum height of 4-percent chord, and one had a linear variation of twist with 6 deg of washout at the tip. Tests were made with natural and fixed transition at Reynolds numbers ranging from 1.2 x 10(exp 6) to 3.6 x 10(exp 6) through an angle-of-attack range of -20 deg to 20 deg. When compared with the flat wing, the effect of the linear variation of twist with 6 deg of washout at the tip was to increase the lift-drag ratio when the leading edge was subsonic; but little increase in lift-drag ratio was obtained when the leading edge was supersonic. Pitching moment was increased and gave a positive trim point without greatly affecting the rate of change of pitching moment with lift coefficient. For the cambered wing the high minimum drag resulted in comparatively low lift-drag ratios. In addition, the pitching moments were decreased so that a negative trim point was obtained.

Landrum, Emma Jean↗

Drag of C-Class Airship Hulls of Various Fineness Ratios

This report presents the results of wind-tunnel tests on eight C-class airship hulls with various fineness ratios, conducted in the Navy Aerodynamic Laboratory, Washington. The purpose of the tests was to determine the variation of resistance with fineness ratio, and also to find the pressure and friction elements of the total drag for the model having the least shape coefficient. Seven C-class airship hulls with fineness ratios of 1.0, 1.5, 2.0, 3.0, 6.0, 8.0, and 10.0 were made and verified. These models and also the previously constructed original C-class hull, whose fineness ratio is 4.62, were then tested in the 8 by 8 foot tunnel for drag of 0 degree pitch and yaw, at various wind speeds. The original hull, which was found to have the least shape coefficient, was then tested for pressure distribution over the surface at various wind speeds. (author)

Zahm, A F↗

Effects of Nacelle configuration/position on performance of subsonic transport

An experimental study was conducted to explore possible reductions in installed propulsion system drag due to underwing aft nacelle locations. Both circular (C) and D inlet cross section nacelles were tested. The primary objectives were: to determine the relative installed drag of the C and D nacelle installations; and, to compare the drag of each aft nacelle installation with that of a conventional underwing forward, drag of each aft nacelle installation with that of a conventional underwing forward, pylon mounted (UTW) nacelle installation. The tests were performed in the NASA-Langley Research Center 16-Foot Transonic Wind Tunnel at Mach numbers from 0.70 to 0.85, airplane angles of attack from -2.5 to 4.1 degrees, and Reynolds numbers per foot from 3.4 to 4.0 million. The nacelles were installed on the NASA USB full span transonic transport model with horizontal tail on. The D nacelle installation had the smallest drag of those tested. The UTW nacelle installation had the largest drag, at 6.8 percent larger than the D at Mach number 0.80 and lift coefficient (C sub L) 0.45. Each tested configuration still had some interference drag, however. The effect of the aft nacelles on airplane lift was to increase C sub L at a fixed angle of attack relative to the wing body. There was higher lift on the inboard wing sections because of higher pressures on the wing lower surface. The effects of the UTW installation on lift were opposite to those of the aft nacelles.

Bangert, L. H.↗

Dynamics and control of coherent structures in the turbulent wall layer: An overview

We expand the velocity field in the vicinity of the wall in empirical eigenfunctions obtained from experiment. Truncating our system and using Galerkin projection, we obtain a closed set of non-linear ordinary differential equations with ten degrees of freedom. We find a rich dynamical behavior, including in particular a heteroclinic attracting orbit giving rise to intermittency. The intermittent jump from one attracting point to the other resembles in many respects the bursts observed in experiments. Specifically, the time between jumps and the duration of the jumps, is approximately that observed in a burst; the jump begins with the formation of a narrowed and intensified updraft, like the ejection phase of a burst, and is followed by a gentle, diffuse downdraft like the sweep phase of a burst. The magnitude of the Reynolds stress spike produced during a burst is limited by our truncation. The behavior is quite robust, much of it being due to the symmetries present (Aubry's group has examined dimensions up to 128 with persistence of the global behavior). We have examined eigenvalues and coefficients obtained from experiment, and from exact simulation, which differ in magnitude. Similar behavior is obtained in both cases; in the latter case, the heteroclinic orbits connect limit cycles instead of fixed points, corresponding to cross-stream waving of the streamwise rolls. The bifurcation diagram remains structurally similar, but somewhat distorted. The role of the pressure term is made clear - it triggers the intermittent jumps, which otherwise would occur at longer and longer intervals, as the system trajectory is attracted closer and closer to the heteroclinic cycle. The pressure term results in the jumps occurring at essentially random times, and the magnitude of the signal determines the average timing. Stretching of the wall region shows that the model is consistent with observations of polymer drag reduction. Change of the third order coefficients, corresponding to acceleration or deceleration of the mean flow, changes the heteroclinic cycles from attracting to repelling, increasing or decreasing the stability, in agreement with observations. The existence of fixed points is an artifact introduced by the projection; however, a decoupled model still displays the rich dynamics. Numerous assumptions made in Aubry et al. (1988) can now be proved exactly. Feeding back eigenfuncitons with the proper phase can delay the bursting, (the heteroclinic jump to the other fixed point), decreasing the drag. It is also possible to speed up the bursting, increasing mixing to control separation. Our approach is optimal for short time tracking in control.

Berkooz, Gal↗

A Computational and Experimental Study of Nonlinear Aspects of Induced Drag

Despite the 80-year history of classical wing theory, considerable research has recently been directed toward planform and wake effects on induced drag. Nonlinear interactions between the trailing wake and the wing offer the possibility of reducing drag. The nonlinear effect of compressibility on induced drag characteristics may also influence wing design. This thesis deals with the prediction of these nonlinear aspects of induced drag and ways to exploit them. A potential benefit of only a few percent of the drag represents a large fuel savings for the world's commercial transport fleet. Computational methods must be applied carefully to obtain accurate induced drag predictions. Trefftz-plane drag integration is far more reliable than surface pressure integration, but is very sensitive to the accuracy of the force-free wake model. The practical use of Trefftz plane drag integration was extended to transonic flow with the Tranair full-potential code. The induced drag characteristics of a typical transport wing were studied with Tranair, a full-potential method, and A502, a high-order linear panel method to investigate changes in lift distribution and span efficiency due to compressibility. Modeling the force-free wake is a nonlinear problem, even when the flow governing equation is linear. A novel method was developed for computing the force-free wake shape. This hybrid wake-relaxation scheme couples the well-behaved nature of the discrete vortex wake with viscous-core modeling and the high-accuracy velocity prediction of the high-order panel method. The hybrid scheme produced converged wake shapes that allowed accurate Trefftz-plane integration. An unusual split-tip wing concept was studied for exploiting nonlinear wake interaction to reduced induced drag. This design exhibits significant nonlinear interactions between the wing and wake that produced a 12% reduction in induced drag compared to an equivalent elliptical wing at a lift coefficient of 0.7. The performance of the split-tip wing was also investigated by wing tunnel experiments. Induced drag was determined from force measurements by subtracting the estimated viscous drag, and from an analytical drag-decomposition method using a wake survey. The experimental results confirm the computational prediction.

Smith, Stephen C.↗

Viscous induced drag

A fundamentally new approach to the aircraft minimum induced drag problem is presented. The method, a 'viscous lifting line', is based on the minimum entropy production principle and does not require the planar wake assumption. An approximate, closed form solution is obtained and compared with several classical results. In addition, the problem of optimizing in-plane wing sweep with constant wing root bending moment is considered. Like the classical lifting line theory, this theory predicts that induced drag is proportional to the square of the lift coefficient and inversely proportional to the wing aspect ratio. Unlike the classical theory, it predicts that in-plane wing sweep may significantly reduce induced drag, that induced drag is Reynolds number dependent, and that the optimum spanwise circulation distribution is non-elliptic.

Greene, George C.↗

Test results at transonic speeds on a contoured over-the-wing propfan model

A semispan wing/body model with a powered highly loaded propeller has been tested to provide data on the propulsion installation drag of advanced propfan-powered aircraft. The model had a supercritical wing with a contoured over-the-wing nacelle. It was tested in the Ames Research Center's (ARC) 14-foot Transonic Wind Tunnel at a total pressure of 1 atm. The test was conducted at angles of attack from -0.5 to 4 deg at Mach numbers ranging from 0.6 to 0.8. The test objectives were to determine propeller performance, exhaust jet effects, propeller slipstream interference drag, and total powerplant installation drag. Test results indicated a total powerplant installation drag of 82 counts (0.0082) at a Mach number of 0.8 and a lift coefficient of 0.5, which is approximately 29 percent of a typical airplane cruise drag.

Levin, Alan D.↗

Reduction of Base Drag on Launch Vehicles

This report describes the work accomplished during a first-year investigation of base drag reduction for launch vehicles. Interest in this work has arisen due to the large base areas associated with the current generation of launch vehicles. For example, the X-33 and Venture Star configurations all have large base areas because of the aero-spike engines they use. Because of the large base-to-wetted area ratios of these vehicles, the majority of the vehicle drag is due to base drag. Based on previous research, there appears to be a means for reducing the base drag on such vehicles. A clear relationship between viscous fore-body drag and base drag was demonstrated. For subsonic flow conditions, an increase in fore-body drag causes a decrease in base drag. This base-drag reduction is a result of boundary layer effects at the base of the vehicle. The shear layer that develops from the boundary layer separating at the back of the vehicle is the conduit through which momentum is transferred from the high energy free-stream flow to the low-energy fluid in the base area. One way to think of the base drag is that it is the momentum required to accelerate this low-energy fluid. The boundary layer that develops on the fore body acts as an "insulator" between the external flow and the low-energy air at the base. As the viscous fore-body drag is increased, the boundary layer thickness at the aft end of the fore body increases, thereby reducing the rate at which momentum is transferred to the base area. As a result of the lower momentum transfer (or reduced pumping), the base pressure coefficient rises resulting in a reduction of base drag.

Naughton, Jonathan↗

The Effect of Surface Irregularities on Wing Drag. I. Rivets and Spot Welds: Rivets and Spot Welds - 1

Tests have been conducted in the NACA 8-foot high-speed wind tunnel to determine the effect of exposed rivet heads and spot welds on wing drag. Most of the tests were made with an airfoil of 5-foot chord. The air speed was varied from 80 to 500 miles per hour and the lift coefficient from 0 to 0.30. The increases in the drag of the 5-foot airfoil varied from 6%, due to countersunk rivets, to 27%, due to 3/32-inch brazier-head rivets, with the rivets in a representative arrangement. The drag increases caused by protruding rivet heads were roughly proportional to the height of the heads. With the front row of rivets well forward, changes in spanwise pitch had negligible effects on drag unless the pitch was more than 2.5% of the chord. Data are presented for evaluating the drag reduction attained by removing rivets from the forward part of the wing surface; for example, it is shown that over 70% of the rivet drag is caused by the rivets on the forward 30% of the airfoil in a typical case.

Hood, Manley J.↗

Grid generation and flow computation about a Martian entry vehicle

A number of vehicles are currently being proposed for a manned mission to Mars. One of these vehicles has a modified blunt-nosed cone configuration. Experimental results were obtained for this vehicle in 1968. They show lift-over-drag ratios comparable to those needed for Mars entry. Computations are performed to verify the earlier results and to further describe the flight characteristics of this vehicle. An analytical method is used to define the surface of this vehicle. A single-block volume grid is generated around the vehicle using the algebraic Two-Boundary Grid Generation algorithm (TBGG) and transfinite interpolation. Euler solutions are then obtained from a Langley Aerodynamic Upward Relaxation Algorithm (LAURA) at Mach 6.0 and angles of attack of 0, 6, and 12 deg. The lift coefficient determined from the LAURA code agree very well with the experimental results. The drag and pitching moment coefficients, however, are underestimated by the code since viscous effects are not considered. Contour plots of the flowfield show no evidence of separation for angles of attack up to 12 deg.

Stewart, J. E.↗

OC6 Phase Ia: CFD Simulations of the Free-Decay Motion of the DeepCwind Semisubmersible

Currently, the design of floating offshore wind systems is primarily based on mid-fidelity models with empirical drag forces. The tuning of the model coefficients requires data from either experiments or high-fidelity simulations. As part of the OC6 (Offshore Code Comparison Collaboration, Continued, with Correlation, and unCertainty (OC6) is a project under the International Energy Agency Wind Task 30 framework) project, the present investigation explores the latter option. A verification and validation study of computational fluid dynamics (CFD) models of the DeepCwind semisubmersible undergoing free-decay motion is performed. Several institutions provided CFD results for validation against the OC6 experimental campaign. The objective is to evaluate whether the CFD setups of the participants can provide valid estimates of the hydrodynamic damping coefficients needed by mid-fidelity models. The linear and quadratic damping coefficients and the equivalent damping ratio are chosen as metrics for validation. Large numerical uncertainties are estimated for the linear and quadratic damping coefficients; however, the equivalent damping ratios are more consistently predicted with lower uncertainty. Some difference is observed between the experimental and CFD surge-decay motion, which is caused by mechanical damping not considered in the simulations that likely originated from the mooring setup, including a Coulomb-friction-type force. Overall, the simulations and the experiment show reasonable agreement, thus demonstrating the feasibility of using CFD simulations to tune mid-fidelity models.

17 WIND ENERGY↗