Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Critical”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Critical mass flux through short Borda type inlets of various cross sections

Mass flux measurements associated with chocked flows through four Borda type inlet geometries: circular, square, triangular and rectangular (two-dimensional) and two sharp edged geometries taken over a very wide range of inlet stagnation conditions. The measurements indicate that: (1) the mass flux is independent of the inlet cross-section geometry and (2) the mass flux is dependent only on the inlet stagnation conditions. Also by using choked flow results found in the literature, the reduced mass flux is independent of working fluid. Two implications are drawn which remain to be verified: (1) since seal leak rates are weakly dependent on geometry but pressure distribution is strongly dependent on geometry, seal design efforts should be directed more toward controlling the dynamics, and (2) high-L/D ducts of arbitrary cross section and Borda type inlets can possess free jets.

Hendricks, R. C.↗
NASA NTRS1979

Design and application of a test rig for super-critical power transmission shafts

The design, assembly, operational check-out and application of a test facility for testing supercritical power transmission shafts under realistic conditions of size, speed and torque are described. Alternative balancing methods and alternative damping mechanisms are demonstrated and compared. The influence of torque upon the unbalance distribution is studied, and its effect on synchronous vibrations is investigated. The feasibility of operating supercritical power transmission shafting is demonstrated, but the need for careful control, by balancing and damping, of synchronous and nonsynchronous vibrations is made clear. The facility was demonstrated to be valuable for shaft system development programs and studies for both advanced and current-production hardware.

Darlow, M.↗
NASA NTRS1979

A critical examination of stresses in an elastic single lap joint

The results of an approximate nonlinear finite-element analysis of a single lap joint are presented and compared with the results of a linear finite-element analysis, and the geometric nonlinear effects caused by the load-path eccentricity on the adhesive stress distributions are determined. The results from finite-element, Goland-Reissner, and photoelastic analyses show that for a single lap joint the effect of the geometric nonlinear behavior of the joint has a sizable effect on the stresses in the adhesive. The Goland-Reissner analysis is sufficiently accurate in the prediction of stresses along the midsurface of the adhesive bond to be used for qualitative evaluation of the influence of geometric or material parametric variations. Detailed stress distributions in both the adherend and adhesive obtained from the finite-element analysis are presented to provide a basis for comparison with other solution techniques.

Cooper, P. A.↗
NASA NTRS1979

Critical considerations for wind-tunnel testing V/STOL aircraft models

Low-speed wind-tunnel testing of V/STOL aircraft concepts to determine the aerodynamic-propulsion interaction effects during the transition between hover and wingborne flight is a necessary step in the development cycle of this type of aircraft. The paper examines factors which must be dealt with to assure that the information obtained in experiments is accurate and representative of the full-scale aircraft modeled. Areas of discussion include: (1) Proper engine simulation selection and model size constraints as a result of the selection; (2) selection of reference power-off condition for determining propulsion interaction effects; (3) modeling of realistic flight conditions to obtain a comprehensive evaluation of the entire transition performance; and (4) wind-tunnel boundary interferences and how these are highly configuration dependent.

Margason, R. J.↗
NASA NTRS1979

Critical influence of finite rate chemistry and unmixedness on ignition and combustion of supersonic H2-air streams

Good agreement has been obtained between published profiles of composition and pitot pressure and the calculated results from a computer program in which finite rate chemistry was used. Significant differences are noted between results calculated using 7 species and 8 reactions and those calculated using 12 species and 25 reactions. Differences are also found between results in which the effect of unmixedness on reaction in turbulent flow is applied or is not applied.

Evans, J. S.↗
NASA NTRS1978

Some flow phenomena in a constant area duct with a Borda type inlet including the critical region

Mass limiting flow characteristics for a 55 L/D tube with a Borda type inlet have been assessed over large ranges of temperature and pressure using fluid nitrogen. Under certain conditions, separation and pressure drop at the inlet was sufficiently strong to permit partial vaporization and the remaining fluid flowed through the tube as if it were a free jet. An empirical relation was determined which defines conditions under which this type of flow can occur. A flow coefficient is presented which enables one to estimate flow rates over the experimental range. A flow rate stagnation pressure map for selected stagnation isotherms and pressure profiles document these flow phenomena.

Hendricks, R. C.↗
NASA NTRS1980

Test fittings for dimensionally critical tubes

Method using lightweight fitting protects tubes and tube stubs during testing and through to final welding. Fitting does not interfere with final welding or brazing like temporary test fittings, and is not heavy like machined-on integral fittings with face-seal 0-rings. Fitting approach is adaptable to many types of components, including valves, transducers, and filters.

Hagler, R.↗
NASA NTRS1979

Investigation of critical burning of fuel droplets

The general problem of spray combustion was investigated. The combustion of bipropellent droplets; combustion of hydrozine fuels; and combustion of sprays were studied. A model was developed to predict mean velocities and temperatures in a combusting gas jet.

Faeth, G. M.↗
NASA NTRS1980

Status of the DOE/NASA critical gas turbine research and technology project

Activities performed in order to provide an R&T data base for utility gas turbine systems burning coal-derived fuels are described. Experiments were run to determine the corrosivity effects of trace metal contaminants (and potential fuel additives) on gas turbine materials and these results were correlated in a corrosion-life prediction model. Actual fuels were burned in a burner rig hot corrosion test to verify the model. A deposition prediction model was assembled and compared with results of actual coal-derived fuel deposition tests. Thermal barrier coatings were tested to determine their potential for protecting gas turbine hardware from the corrosive contaminants. Several coatings were identified with significantly improved spallation-resistance (and, hence, corrosion resistance).

Clark, J. S.↗
NASA NTRS1979

Critical mass flux through short Borda type inlets of various cross sections

Mass flux measurements associated with choked flows through four Borda-type inlet geometries: circular, square, triangular, and rectangular (two-dimensional) and two sharp-edged geometries are discussed for a wide range of inlet stagnation conditions. The results obtained indicate that the mass flux is independent of the inlet cross-section geometry, while it is dependent on the inlet stagnation conditions. The results also suggest that parallel surfaces as found in seals, dampers, bearings, and heat exchanger tubes of rectangular cross section with Borda-type inlet configurations are subject to large forces. It is noted that the reduced mass flux is independent of working fluid.

Hendricks, R. C.↗