Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Control Rocket”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Adsorption and chemical reaction of gaseous mixtures of hydrogen chloride and water on aluminum oxide and application to solid-propellant rocket exhaust clouds

Hydrogen chloride (HCl) and aluminum oxide (Al2O3) are major exhaust products of solid rocket motors (SRM). Samples of calcination-produced alumina were exposed to continuously flowing mixtures of gaseous HCl/H2O in nitrogen. Transient sorption rates, as well as maximum sorptive capacities, were found to be largely controlled by specific surface area for samples of alpha, theta, and gamma alumina. Sorption rates for small samples were characterized linearly with an empirical relationship that accounted for specific area and logarithmic time. Chemisorption occurred on all aluminas studied and appeared to form from the sorption of about a 2/5 HCl-to-H2O mole ratio. The chemisorbed phase was predominantly water soluble, yielding chloride/aluminum III ion mole ratios of about 3.3/1 suggestive of dissolved surface chlorides and/or oxychlorides. Isopiestic experiments in hydrochloric acid indicated that dissolution of alumina led to an increase in water-vapor pressure. Dissolution in aqueous SRM acid aerosol droplets, therefore, might be expected to promote evaporation.

Cofer, W. R., III↗
NASA NTRS1982

Improved pointing at trackable targets by integrating control valve signals

A compact, low-cost add-on electronic module has been developed for the STRAP III control system to improve pointing at trackable targets. The module provides peak-to-peak limit cycle excursions of + or - 5 arcseconds while tracking a +3 magnitude or brighter star. This is achieved without using rate-integrating gyroscopes, thus reducing payload length, weight, cost, and preparation time. This module has flown successfully five times. In May 1981, it improved the performance of a two-startracker attitude control system with TV camera and joystick control which pointed at a nontrackable target. This paper describes the operation of the module, how it alters the ordinary STRAP III operation, and how it was developed using an analog-computer-based rocket flight simulator.

Stone, R. W.↗
NASA NTRS1987

Space Shuttle guidance for multiple main engine failures during first stage

This paper presents contingency abort guidance schemes recently developed for multiple Space Shuttle main engine failures during the first two minutes of flight (first stage). The ascent and entry guidance schemes greatly improve the possibility of the crew and/or the Orbiter surviving a first stage contingency abort. Both guidance schemes were required to meet certain structural and controllability constraints. In addition, the systems were designed with the flexibility to allow for seasonal variations in the atmosphere and wind. The ascent scheme guides the vehicle to a desirable, lofted state at solid rocket booster burnout while reducing the structural loads on the vehicle. After Orbiter separation from the solid rockets and the external tank, the entry scheme guides the Orbiter through one of two possible entries. If the proper altitude/range/velocity conditions have been met, a return-to-launch-site 'Split-S' maneuver may be attempted. Otherwise, a down-range abort to an equilibrium glide and subsequent crew bailout is performed.

Sponaugle, Steven J.↗
NASA NTRS2000

Olympus: The Ultimate Summit for Science

High above the world-class observatories that dot Hawaii's dormant Mauna Kea volcano, floating farther yet over the hostile and nearly inaccessible peaks of Mt. Everest, lies a summit waiting to be conquered. Here above the clouds and city lights and over 99.7% of the atmosphere is a platform on the edge of space, home to a broad range of astronomy and physics experiments. Today, balloons are lifting experiments longer, higher and more inexpensively than ever before, and returning them safely to Earth for reuse. Week-long flights at altitudes of approximately 35 kilometers carrying payloads in excess of several tons are the norm. NASA now plans to extend this platform and create a new generation of balloons capable of staying afloat with such cargo for 100 days and ultimately 1,000 days. What do some scientists hope to accomplish with 100 or even 1,000 days at the edge of space? To name but a few proposals on the table: Jupiter-size planet searches, large-aperture solar astronomy, large-aperture infrared astronomy, cosmic-ray investigations, long-duration Earth science missions, and hard x-ray imaging experiments. Olympus defines a new era in scientific ballooning. Advances in material science and trajectory control are enabling revolutionary capabilities. Very large scientific payloads can now be reliably launched and retrieved for reflight at a range of altitudes. Balloon flight still remains a fraction of the cost of a rocket launch. The ultra long duration balloon, with its 100-day maiden flight planned for 2001, provides a long-term facility in a near-space environment for many types of science. This is a stratospheric mountaintop well worth the climb.

Kelly, Darrell↗
NASA NTRS2002

STS-111 Mission Highlights Resource Tape: Flight Days 1 - 4 - Part 1 of 4

This video, Part 1 of 4, shows the activities of the STS-111 crew (Kenneth Cockrell, Commander; Paul Lockhart, Pilot; Franklin Chang-Diaz, Phillipe Perrin, Mission Specialists) during flight days 1 through 4. Also shown are the incoming Expedition 5 (Valeri Korzun, Commander; Peggy Whitson, NASA ISS Science Officer; Sergei Treschev, Flight Engineer) and outgoing Expedition 4 (Yuri Onufriyenko, Commander; Carl Walz, Daniel Bursch, Flight Engineers) crews of the ISS (International Space Station). The activities from other flight days can be seen on 'STS-111 Mission Highlights Resource Tape' Part 2 of 4 (internal ID 2002139469), 'STS-111 Mission Highlights Resource Tape' Part 3 of 4 (internal ID 2002139468), and 'STS-111 Mission Highlights Resource Tape' Part 4 of 4 (internal ID 2002139474). The primary activity of flight day 1 is the launch of Space Shuttle Endeavour. The crew is seen before the launch at a meal and suit-up, and some pre-flight procedures are shown. Perrin holds a sign with a personalized message. The astronauts communicate with Mission Control extensively after launch, and an inside view of the shuttle cabin is shown. The replays of the launch include close-ups of the nozzles at liftoff, and the fall of the solid rocket boosters and the external fuel tank. Flight day 2 shows footage of mainland Asia at night, and daytime views of the eastern United States and Lake Michigan. Flight day three shows the Endeavour orbiter approaching and docking with the ISS. After the night docking, the crews exchange greetings, and a view of the Nile river and Egypt at night is shown. On flight day 4, the MPLM (Multi-Purpose Logistics Module) Leonardo was temporarily transferred from Endeavour's payload bay to the ISS.

Source record↗
NASA NTRS2001

TAXI Interface Demultiplexes Proprietarily Formatted Data

The 'TAXI Direct-to-Disk' interface is a special purpose interface unit for demultiplexing of data from a Racal Storeplex (or equivalent) multichannel recorder onto one or more hard disks that reside in, and/or are controlled by, a personal computer (PC). The acronym 'TAXI' signifies transparent asynchronous transceiver interface. The TAXI interface was developed for original use in capturing data from instrumentation on a test stand in a NASA rocket testing facility. The installation of the TAXI interface, in conjunction with other modifications, causes the transfer of data to take place in real time, so that the data are immediately available for review during or after the test.

Newnan, Bruce G.↗
NASA NTRS1950

Preliminary Results of a Flight Investigation of 1/6-Scale Rocket-Powered Models of the Bell MX-776 to Determine Aileron Rolling Effectiveness and Total Drag

An experimental investigation of the variation of aileron rolling effectiveness and total drag with Mach number has been made using 1/6-scale rocket-propelled models of the Bell MX-776. Three models having constant-chordwise-thickness full-span aileron at approximate deflections of 2 deg, 5 deg, and 15 deg have been flown. Positive control effectiveness over the Mach number range between approximately 0.5 and 1.2 was obtained from the models and no indication of reversal of effectiveness was encountered. The ratio of tip helix angle to aileron deflection indicated a decrease in proportional rolling effectiveness with increasing deflections in the Mach number range from approximately 0.7 to 1.0. A drag rise of about 125 percent in the transonic region between Mach numbers of 0.85 and 1.02 followed by a gradual decrease at higher speeds was revealed.

Stevens, Joseph E.↗
NASA NTRSDate not supplied

Flight Software for the LOFTID Re-Entry Vehicle

NASA’s Low-Earth Orbit Flight Test of an Inflatable Decelerator, or LOFTID, demonstrated re-entry from low-Earth orbit of a 6-meter aeroshell designed to be used as a heat shield that is larger than the rocket shroud, enabling the return of much greater mass. The LOFTID Flight Software was developed in-house and consists of three components: the Power Distribution software, the Data Recorder software, and the Camera Controller software, along with the Ground Software used for testing, operations, data integrity, and data processing. This presentation will discuss issues found in developing the Power Distribution software in cFS on a non-Linux POSIX platform, designing an efficient architecture for recording of high bandwidth data, controlling over a dozen cameras in-flight, and creating the ground support tools to verify data integrity and support the post-processing of flight data.

Paul Brewster↗
NASA NTRS1973

Compton scatter attenuation gamma ray spectrometer

A gamma ray spectrometer is described for use in intense radiation fields such as those in the vicinity of a rocket engine exhaust. A collimated radiation beam is Compton scattered toward shielded spectrometers to reduce the energy and intensity of the radiation and is energy selective among the spectrometers. The scattering targets are changeable to control the percentage of the radiation scattered. Sum-Compton coincidence techniques are employed for data selection.

Austin, W. E.↗
NASA NTRS1973

Space Shuttle system solid rocket booster.

Description of the mission and systems requirement of the solid rocket booster as it supports the Shuttle vehicle configuration. The solid booster is equipped with load skirts and linkages that can accommodate full mission loads, a solid propellant motor for delivering required performance, thrust vector control for augmentation of Shuttle vehicle ascent control, staging and separation systems, and electrical subsystems. To recover and reuse the solid booster case a recovery package is provided. The definition of these functional elements of the solid booster are discussed with the requirements placed on each element to satisfy the overall booster objective.

Thomason, H. E.↗
NASA NTRS1975

The design, development, fabrication and testing of two (2) Non-Spin Platforms, (NSP)

The non spin platform is a means for achieving the very low acceleration requirements for cost effective space processing experiments on research rocket flights. These platforms have a low initial cost, are re-usable and have extremely low refurbishment cost. In order to attain this goal, commercially available components were used and only the necessary quality control standards were imposed. A detailed system description, the very few design problems encountered, the operational procedures (both pre-flight and post-flight), and the maintenance requirements are described.

Source record↗
NASA NTRS1982

A technology data base for the design of 500 to 5000-lb thrust class liquid rocket engines utilizing hydrogen and oxygen as propellants

This paper presents an overview of the results of experimental evaluations of candidate designs for igniters, injectors, and propellant-cooled thrust chambers applicable to restartable high-performance, high-reliability upper-stage engines and to pulsing-type reaction control engines (RCE). Injection element types best suited for liquid, gas, and liquid/gas phase propellant supply are identified. The resulting interactions between element type, combustion efficiency, and chamber wall heating are compared. The distinction between thrust chamber design requirements for upper stage vs RCE applications as measured by cycle life requirements is translated into design configurations consisting of all-film-cooled, all-regeneratively-cooled, and composites of the two cooling approaches. The validity of the design approaches is confirmed by data from engine durability testing involving over 90,000 starts and 9,000 thermal cycles on RCE-type designs and multiple long-duration burns (up to 2,000 sec) on regeneratively cooled upper-stage designs.

Schoenman, L.↗
NASA NTRS1991

Cryogenic combustion laboratory

The objective is to establish a major experimental laboratory for studying fundamental processes such as mixing and combustion under liquid rocket engine conditions. The capability of this laboratory will include operation using a variety of fuel and oxidizer systems including liquid oxygen and liquid hydrocarbons. In addition to providing the proper facilities for supplying and controlling these fuels and oxidizers, a specific effort is being made to provide a state-of-the-art diagnostic capability for combustion measurements. In particular, optical and laser-based techniques are being emphasized for measurements of species, velocities, and spray characteristics.

Santoro, R. J.↗
NASA NTRS1991

Integrated flow and structural modeling for rocket engine component test facility propellant systems

A set of PC-based computational Dynamic Fluid Flow Simulation models is presented for modeling facility gas and cryogenic systems. Data obtained provide important information regarding performance envelope parameters for the facility using different engine components; time-dependent valve setting for controlling steady-state, quasi-steady state, and transient profiles; optimum facility pipe and pipe component sizes and parameters; momentum transfer loads; and fluid conditions at critical points. A set of COSMIC NASTRAN-based finite element models is also presented to evaluate the loads and stresses on test facility piping systems from fluid and gaseous effects, thermal chill down, and occasional wind loads. The models are based on Apple Macintosh software which makes it possible to change numerous parameters.

Dequay, L.↗
NASA NTRS1993

Qualification test of the Ross Double Planetary Mixer

This test report describes the qualification test of the Ross Double Planetary Mixer used to mix room temperature vulcanized (RTV) silicone (Dow Corning 90-006-2) for the redesigned solid rocket motor (RSRM) nozzle joints. Testing was completed 18 June 1993 in the M-113A Nozzle Fabrication Facility at Thiokol Corporation, Space Operations, Brigham City, Utah. The Ross mixer provides better mixing and better control on temperature and humidity, resulting in better quality RTV and a longer usable pot life. The test began on 3 May 1993 and was stopped due to operator error during the tensile strength and elongation testing. Specimens were ruined without gathering any useful data. A 'no test' was declared, the problem was remedied, and the test was re-run with MSFC approval. The test was run and all pass/fail criteria were met, most with a considerable margin. The Ross Double Planetary Mixer met all certification objectives and is recommended for immediate use for mixing RTV silicone for RSRM nozzle joints.

Lueders, Kurt F.↗
NASA NTRS1991

Lewis Research Center R and D Facilities

The NASA Lewis Research Center (LeRC) defines and develops advanced technology for high priority national needs. The work of the Center is directed toward new propulsion, power, and communications technologies for application to aeronautics and space, so that U.S. leadership in these areas is ensured. The end product is knowledge, usually in a report, that is made fully available to potential users--the aircraft engine industry, the energy industry, the automotive industry, the space industry, and other NASA centers. In addition to offices and laboratories for almost every kind of physical research in such fields as fluid mechanics, physics, materials, fuels, combustion, thermodynamics, lubrication, heat transfer, and electronics, LeRC has a variety of engineering test cells for experiments with components such as compressors, pumps, conductors, turbines, nozzles, and controls. A number of large facilities can simulate the operating environment for a complete system: altitude chambers for aircraft engines; large supersonic wind tunnels for advanced airframes and propulsion systems; space simulation chambers for electric rockets or spacecraft; and a 420-foot-deep zero-gravity facility for microgravity experiments. Some problems are amenable to detection and solution only in the complete system and at essentially full scale. By combining basic research in pertinent disciplines and generic technologies with applied research on components and complete systems, LeRC has become one of the most productive centers in its field in the world. This brochure describes a number of the facilities that provide LeRC with its exceptional capabilities.

Source record↗
NASA NTRS1995

Mathematical Model Of Curing Behavior Of A Polymer

Mathematical model predicts selected aspects of chemical, thermal and mechanical responses of polymeric liner and propellant materials during curing process. Predictions made both prior to processing and during process in quasi-real time. Developed specifically for use in designing and analyzing process in which bondline materials (including polymeric liners) and propellant cast and cured in rocket motor. With modifications, model applicable to curing of other polymeric materials. Further development may provide direct "in-line" program for calculations, including comparisons, in real time. This will constitute basis for more sophisticated control of process.

Loomis, Willard C.↗
NASA NTRS1951

Preliminary Results Obtained from Flight Test of a 1/7-Scale Rocket-Powered Model of the Grumman XF10F Airplane Configuration in the Swept-Wing Condition, TED No. NACA DE 354

A flight investigation of a 1/7-scale rocket-powered model of the XF10F Grumman XFl0F airplane in the swept-wing configuration has been made. The purpose of this test was to determine the static longitudinal stability, damping in pitch, and longitudinal control effectiveness of the airplane with the center of gravity at 20 percent of the wing mean aerodynamic chord. Only a small amount of data was obtained from the test because, immediately after booster separation at a Mach number of 0.88, the configuration was directionally unstable and diverged in sideslip. Simultaneous with the sideslip divergence, the model became longitudinally unstable at 3 degree angle of attack and -6 degree sideslip and diverged in pitch to a high angle of attack. During the pitch-up the free-floating horizontal tail became unstable at 5 degree angle of attack and the tail drifted against its positive deflection limit.

Gardner, William N.↗