Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSION RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Extrapolation From Wind Tunnel to Flight: Shuttle Orbiter Aerodynamics

The paper reviews a combined numerical and experimental activity on the Shuttle Orbiter, first performed at NASA Langley within the Orbiter Experiment (OEX) and subsequently at ESA, as part of the AGARD FDP WG 18 activities. The study at Langley was undertaken to resolve the pitch up anomaly observed during the entry of the first flight of the Shuttle Orbiter. The present paper will focus on real gas effects on aerodynamics and not on heating. The facilities used at NASA Langley were the 15-in. Mach 6, the 20-in, Mach 6, the 31-in. Mach 10 and the 20-in. Mach 6 CF4 facility. The paper focuses on the high Mach, high altitude portion of the first entry of the Shuttle where the vehicle exhibited a nose-up pitching moment relative to pre-flight prediction of (AC,) = 0.03. In order to study the relative contribution of compressibility, viscous interaction and real gas effects on basic body pitching moment and flap efficiency, an experimental study was undertaken to examine the effects of Mach, Reynolds and ratio of specific heats at NASA. At high Mach, a decrease of gamma occurs in the shock layer due to high temperature effects. The primary effect of this lower specific heat ratio is a decrease of the pressure on the aft windward expansion surface of the Orbiter causing the nose-up pitching moment. Testing in the heavy gas, Mach 6 CF4 tunnel, gave a good simulation of high temperature effects. The facilities used at ESA were the 1m Mach 10 at ONERA Modane, the 0.7 m hot shot F4 at ONERA Le Fauga and the 0.88 m piston driven shock tube HEG at DLR Goettingen. Encouraging good force measurements were obtained in the F4 facility on the Orbiter configuration. Testing of the same model in the perfect gas Mach 10 S4 Modane facility was performed so as to have "reference" conditions. When one compares the P4 and S4 test results, the data suggests that the Orbiter "pitch up" is due to real gas effects. In addition, pressure measurements, performed on the aft portion of the windward side of the Halis configuration in HEG and P4, confirm that the pitch up is mainly attributed to a reduction of pressure due to a local decrease in gamma.

J. Muylaert↗
NASA NTRS2006

The Compressive Behavior of Isocyanate-crosslinked Silica Aerogel at High Strain Rates

Aerogels are low-density, highly nano-porous materials. Their engineering applications are limited due to their brittleness and hydrophilicity. Recently, a strong lightweight crosslinked silica aerogel has been developed by encapsulating the skeletal framework of amine-modified silica aerogels with polyureas derived by isocyanate. The mesoporous structure of the underlying silica framework is preserved through conformal polymer coating, and the thermal conductivity remains low. Characterization has been conducted on the thermal, physical properties and the mechanical properties under quasi-static loading conditions. In this paper, we present results on the dynamic compressive behavior of the crosslinked silica aerogel (CSA) using a split Hopkinson pressure bar (SHPB). A new tubing pulse shaper was employed to help reach the dynamic stress equilibrium and constant strain rate. The stress-strain relationship was determined at high strain rates within 114-4386/s. The effects of strain rate, density, specimen thickness and water absorption on the dynamic behavior of the CSA were investigated through a series of dynamic experiments. The Young's moduli (or 0.2% offset compressive yield strengths) at a strain rate approx.350/s were determined as 10.96/2.08, 159.5/6.75, 192.2/7.68, 304.6/11.46, 407.0/20.91 and 640.5/30.47 MPa for CSA with densities 0.205, 0.454, 0.492, 0.551,0.628 and 0.731 g/cu cm, respectively. The deformation and failure behaviors of a native silica aerogel with density (0.472 g/cu cm ), approximately the same as a typical CSA sample were observed with a high speed digital camera. Digital image correlation technique was used to determine the surface strains through a series of images acquired using high speed photography. The relative uniform axial deformation indicated that localized compaction did not occur at a compressive strain level of approx.17%, suggesting most likely failure mechanism at high strain rate to be different from that under quasi-static loading condition. The Poisson s ratio was determined to be 0.162 in nonlinear regime under high strain rates. CSA samples failed generally by splitting, but were much more ductile than native silica aerogels.

Luo, H.↗
NASA NTRS2007

Convergence Acceleration of Runge-Kutta Schemes for Solving the Navier-Stokes Equations

The convergence of a Runge-Kutta (RK) scheme with multigrid is accelerated by preconditioning with a fully implicit operator. With the extended stability of the Runge-Kutta scheme, CFL numbers as high as 1000 can be used. The implicit preconditioner addresses the stiffness in the discrete equations associated with stretched meshes. This RK/implicit scheme is used as a smoother for multigrid. Fourier analysis is applied to determine damping properties. Numerical dissipation operators based on the Roe scheme, a matrix dissipation, and the CUSP scheme are considered in evaluating the RK/implicit scheme. In addition, the effect of the number of RK stages is examined. Both the numerical and computational efficiency of the scheme with the different dissipation operators are discussed. The RK/implicit scheme is used to solve the two-dimensional (2-D) and three-dimensional (3-D) compressible, Reynolds-averaged Navier-Stokes equations. Turbulent flows over an airfoil and wing at subsonic and transonic conditions are computed. The effects of the cell aspect ratio on convergence are investigated for Reynolds numbers between 5:7 x 10(exp 6) and 100 x 10(exp 6). It is demonstrated that the implicit preconditioner can reduce the computational time of a well-tuned standard RK scheme by a factor between four and ten.

Swanson, Roy C., Jr.↗
NASA NTRS2008

Risk Assessment for Titanium Pressure Vessels Operating Inside the ARES I's Liquid Hydrogen Tank Environment

Titanium alloy (Ti-6-4) is currently being proposed for the manufacturing of pressure vessels (PV) for storage of compressed helium gas, which are mounted inside the ARES I's liquid hydrogen (LH2) tank. At cryogenic temperature, titanium alloys usually have the highest strength-to-weight ratio property and have been considered as the metallic materials of choice for lightweight PV operating in LH2 environment. Titanium PV s are also considered as heritage hardware because they have been used by NASA for the Saturn IV-B rocket s LH2 tank in the mid 1960 s. However, hydrogen embrittlement is possible if Ti-6-4 alloy is exposed to gaseous hydrogen at certain pressure and temperature during the LH2 tank filling and draining operations on the launch pad, and during the J2X engine burn period for the ARES I s upper stage. Additionally, the fracture toughness and ductility properties of Ti-6-4 are significantly decreased at cryogenic temperature. These factors do not necessary preclude the use of titanium PV in hydrogen or at cryogenic applications; however, their synergistic effects and the material damage tolerance must be accounted for in the mission life assessment for PV s, which are considered as fracture critical hardware. In this paper, an overview of the risk assessment for Ti-6-4 alloy, strategy to control hydrogen embrittlement and brief metallic material trade study for PV operating in LH2 tank will be presented.

Lee, Jonathan A.↗
DOE OSTI2018

Studies on Workability of Geopolymer Solidification - 18171

In Japan, intermediate-level radioactive waste, such as spent resin, is solidified and set in sealed containers without venting. To reduce the amount of hydrogen generated due to water radiolysis in stored intermediate-level waste, geopolymer solidification has been studied. Geopolymer solidification is an excellent method for conditioning intermediate-level waste from the viewpoint of its high thermal stability and low processing cost. However, it has a problem that the apparent viscosity increases drastically a few minutes after the onset of setting. This may cause some trouble in the process of pouring the geopolymer into drums and mixing it with waste. In this study, in order to control the workability of a geopolymer mixture, we investigated the effects of the compounding ratio and the kinds of chemical agents used. We confirmed that the geopolymer reaction was slowed down by reducing the amount of calcium and adding boron. The uniaxial compressive strength of the geopolymer was 3-80 MPa. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1944

On the general theory of thin airfoils for nonuniform motion

General thin-airfoil theory for a compressible fluid is formulated as boundary problem for the velocity potential, without recourse to the theory of vortex motion. On the basis of this formulation the integral equation of lifting-surface theory for an incompressible fluid is derived with the chordwise component of the fluid velocity at the airfoil as the function to be determined. It is shown how by integration by parts this integral equation can be transformed into the Biot-Savart theorem. A clarification is gained regarding the use of principal value definitions for the integral which occur. The integral equation of lifting-surface theory is used a s the starting point for the establishment of a theory for the nonstationary airfoil which is a generalization of lifting-line theory for the stationary airfoil and which might be called "lifting-strip" theory. Explicit expressions are given for section lift and section moment in terms of the circulation function, which for any given wing deflection is to be determined from an integral equation which is of the type of the equation of lifting-line theory. The results obtained are for airfoils of uniform chord. They can be extended to tapered airfoils. One of the main uses of the results should be that they furnish a practical means for the analysis of the aerodynamic span effect in the problem of wing flutter. The range of applicability of "lifting-strip" theory is the same as that of lifting-line theory so that its results may be applied to airfoils with aspect ratios as low as three.

BIBLIOGRAPHY-WINGS↗
DOE OSTI2024

Ultra-intense femtosecond laser interactions with aligned nanostructures

The interaction of ultrafast laser pulses of relativistic intensity with high aspect ratio nanostructures can efficiently and volumetrically heat matter to an ultra-high-energy-density regime encountered in the center of stars and within the core of fusion capsules compressed by the world’s largest lasers. It also generates gigantic quasi-static electromagnetic fields that accelerate particles to very high energy. Here, we present an overview of the physics and applications of these dense relativistic plasmas that can be created with pulses of relatively modest energy from lasers that can operate at a high repetition rate. Recent nanowire array experiments produced near-solid density plasmas with an extreme degree of ionization (e.g., Au +72 ), converted ultrafast pulses of laser light into intense x-ray flashes with record efficiency, and accelerated ions to MeV energies, efficiently driving micro-scale fusion reactions that generate flashes of quasi-monoenergetic neutrons. These plasmas also serve as a platform for advancing the understanding of atomic processes in extreme environments and open a new pathway to laser-driven fusion energy. The irradiation of nanostructures at intensities of > 1 x 10 22 W cm –2 is predicted to lead to an extreme ultra-high energy density plasma regime characterized by terabar pressures that is virtually unexplored.

Optics↗
DOE OSTI2017

A Curved Magnetic Field in the Ring-like Shell of Bubble N4

We report the detection of a curved magnetic field in the ring-like shell of the bubble N4, derived from near-infrared polarization of reddened diskless stars located behind this bubble. The magnetic field in the shell is curved and parallel to the ring-like shell, and its strength is estimated to be ∼120 μG in the plane of the sky. The magnetic field strength in the shell is significantly enhanced compared to the local field strength. We calculate the mass-to-flux ratio for the submillimeter clumps in the shell and find that they are all magnetically subcritical. Our results demonstrate that the magnetic field strengthens as the interstellar medium is compressed into a shell, and suggest that the magnetic field has the potential to hinder star formation triggered by H ii region expansion.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1976

New potentials for conventional aircraft when powered by hydrogen-enriched gasoline

Overall system efficiency and performance of a Beech Model 20 Duke aircraft was studied to provide analytical representations of an aircraft piston engine system, including all essential components required for onboard hydrogen generation. Lower emission levels and a 20% reduction in fuel consumption may be obtained by using a catalytic hydrogen generator, incorporated as part of the air induction system, to generate hydrogen by breaking down small amounts of the aviation gasoline used in the normal propulsion system. This hydrogen is then mixed with gasoline and compressed air from the turbocharger before entering the engine combustion chamber. The special properties of the hydrogen-enriched gasoline allow the engine to operate at ultra lean fuel/air ratios, resulting in higher efficiencies.

Menard, W. A.↗
NASA NTRS1977

Notched and unnotched fatigue behavior of angle-ply graphite/epoxy composites

The axial fatigue behavior of both notched and unnotched graphite/epoxy composites has been studied as part of a continuing research investigation. In unnotched studies, conducted on an AS/3501 laminate, S-N curves were determined for various stress ratios R using simply supported test specimens. Specimens were fatigue tested up to 5 x 10 to the 6th cycles. Apparent fatigue limits in tension-tension and compression-compression cycling occurred at about 60 percent of the respective static strengths. The overall results were expressed in the form of a constant life diagram (that is, a Goodman diagram) showing the relationship between mean stress and stress amplitude. The diagram shows a linear relationship and illustrates a skew-symmetry in fatigue life caused by the relatively low compressive strength of the unrestrained test specimens used. In effect, a maximum in stress amplitude occurs at a positive value of the mean stress.

Ramani, S. V.↗
NASA NTRS2006

Convergence Acceleration for Multistage Time-Stepping Schemes

The convergence of a Runge-Kutta (RK) scheme with multigrid is accelerated by preconditioning with a fully implicit operator. With the extended stability of the Runge-Kutta scheme, CFL numbers as high as 1000 could be used. The implicit preconditioner addresses the stiffness in the discrete equations associated with stretched meshes. Numerical dissipation operators (based on the Roe scheme, a matrix formulation, and the CUSP scheme) as well as the number of RK stages are considered in evaluating the RK/implicit scheme. Both the numerical and computational efficiency of the scheme with the different dissipation operators are discussed. The RK/implicit scheme is used to solve the two-dimensional (2-D) and three-dimensional (3-D) compressible, Reynolds-averaged Navier-Stokes equations. In two dimensions, turbulent flows over an airfoil at subsonic and transonic conditions are computed. The effects of mesh cell aspect ratio on convergence are investigated for Reynolds numbers between 5.7 x 10(exp 6) and 100.0 x 10(exp 6). Results are also obtained for a transonic wing flow. For both 2-D and 3-D problems, the computational time of a well-tuned standard RK scheme is reduced at least a factor of four.

Swanson, R. C.↗
DOE OSTI2021

Characterization of damage processes in Montney siltstone under triaxial compression using acoustic emission and diagnostic imaging

SUMMARY Crack nucleation and rock failure processes in a fine-grained siltstone (Montney Formation) under triaxial compression are investigated using combined diagnostic techniques, including ultrasonic-wave measurement, acoustic-emission (AE) monitoring, computed tomography (CT) scanning, and thin-section imaging. The sample displays a weak-to-moderate inherent seismic anisotropy and noticeable stress-induced anisotropy prior to failure. No AE event was detected until the applied axial stress reached 95 per cent of the peak value. The signal-to-noise ratio is relatively low, however, and detectable AE events are more diffuse than those observed in highly brittle rocks. The AE locations correlate with a shear fracture zone imaged by CT scanning. AE moment-tensor analysis reveals that events with larger relative magnitudes are characterized by high volumetric (tensile or compressive) components, and the initiation of the failure zone is dominated by combined shear-tensile (ST) failure. Stress inversion of the AE events with high tensile components is in good agreement with the known applied stress. Microscopic imaging of thin sections from the failed sample shows that the failure zone is an en echelon structure consisting of a major fracture with branching micro and minor cracks. This failure mechanism is consistent with a ST source mechanism and is interpreted to be associated with the fine granular structure and mineral composition of Montney siltstone.

Jia, Suzie Q. (ORCID:0000000326496190)↗
NASA NTRS1988

Local crippling of thin-walled graphite-epoxy stiffeners

Results from an experimental and analytical study of the local buckling, postbuckling, and crippling (failure) behavior of channel, zee, and I- and J-section stiffeners made of AS4/3502 graphite-epoxy unidirectional tape are presented. Thirty-six specimens were tested in axial compression. Experimental results indicate the existence of a number of damage initiation modes, all of which involve either delamination in some part of the specimen or local material strength failure in a corner of the specimen. The flange width-to-thickness ratio is found to influence the mode of damage initiation. The inner corner radius strongly affects the crippling stress for the I- and J-section specimens, but was not found to have a significant effect on the crippling stress of channels and zees. Geometrically nonlinear analyses of five specimens were performed with the STAGS general purpose computer code. Correlation between analytical and experimental results is excellent through buckling, but agreement degrades in postbuckling. The discrepancies in postbuckling are attributed to neglect of transverse shearing deformations in the analysis and development of damage in the specimens. Hashin's compressive fiber mode failure criterion correlates reasonably well with the first major damage event in a first ply failure analysis.

Bonanni, David L.↗
NASA NTRS2001

Evaluation of Turbulence-Model Performance in Jet Flows

The importance of reducing jet noise in both commercial and military aircraft applications has made jet acoustics a significant area of research. A technique for jet noise prediction commonly employed in practice is the MGB approach, based on the Lighthill acoustic analogy. This technique requires as aerodynamic input mean flow quantities and turbulence quantities like the kinetic energy and the dissipation. The purpose of the present paper is to assess existing capabilities for predicting these aerodynamic inputs. Two modern Navier-Stokes flow solvers, coupled with several modern turbulence models, are evaluated by comparison with experiment for their ability to predict mean flow properties in a supersonic jet plume. Potential weaknesses are identified for further investigation. Another comparison with similar intent is discussed by Barber et al. The ultimate goal of this research is to develop a reliable flow solver applicable to the low-noise, propulsion-efficient, nozzle exhaust systems being developed in NASA focused programs. These programs address a broad range of complex nozzle geometries operating in high temperature, compressible, flows. Seiner et al. previously discussed the jet configuration examined here. This convergent-divergent nozzle with an exit diameter of 3.6 inches was designed for an exhaust Mach number of 2.0 and a total temperature of 1680 F. The acoustic and aerodynamic data reported by Seiner et al. covered a range of jet total temperatures from 104 F to 2200 F at the fully-expanded nozzle pressure ratio. The aerodynamic data included centerline mean velocity and total temperature profiles. Computations were performed independently with two computational fluid dynamics (CFD) codes, ISAAC and PAB3D. Turbulence models employed include the k-epsilon model, the Gatski-Speziale algebraic-stress model and the Girimaji model, with and without the Sarkar compressibility correction. Centerline values of mean velocity and mean temperature are compared with experimental data.

Woodruff, S. L.↗
DOE OSTI2020

Ability of Particulate Matter Index to describe sooting tendency of various gasoline formulations in a stratified-charge spark-ignition engine

This study investigates the ability of Particulate Matter Index (PMI) to describe the sooting behavior of various gasoline formulations in a stratified-charge (SC) spark-ignition engine. Specifically, the engine was operated at 2000 rpm with an intake pressure of 130 kPa where soot formation is known to primarily occur in the bulk gases. Exhaust soot emissions were measured for nine test fuels at various exhaust gas recirculation levels. A comparison between measured soot levels and PMI shows that PMI is a relatively poor predictor of the sooting tendency of the tested fuels under lean SC combustion. Among the fuels, three fuels, namely the diisobutylene blend, High Olefin, and E30 fuels exhibit measured soot behavior opposite of that predicted by PMI. Optical diagnostics were utilized to further investigate the in-cylinder phenomena for these three fuels. Analysis of natural luminosity and diffused back-illumination extinction imaging suggests that fuel-induced differences in the amount of soot formed are responsible for a majority of the discrepancy in measured versus predicted sooting tendency. Fuel-induced differences in soot oxidation and spray development seem to play minor roles. Because the combustion and air-fuel mixing processes for lean SC combustion are different from conventional stoichiometric operation it is hypothesized that the PMI correlation needs to be modified to account for differences in stoichiometric air-fuel ratio and level of oxygenation between fuels. Furthermore, the role of fuel volatility in PMI possibly needs to be de-emphasized for SC operation with fuel injection into compression-heated gases.

42 ENGINEERING↗
DOE OSTI2020

3D Printing of Liquid Crystal Elastomer Foams for Enhanced Energy Dissipation Under Mechanical Insult

Polymer foams are an essential class of lightweight materials used to protect assets against mechanical insults, such as shock and vibration. Two features are important to enhance their energy absorption characteristics: the foam structure and the matrix phase mechanical behavior. This study investigates novel approaches to control both of these features to enhance the energy absorption capability of flexible lattice foams. First, we consider 3D printing via digital light processing (DLP) as a method to control the foam mesostructure across a suite of periodic unit cells. Second, we introduce an additional energy dissipation mechanism in the solid matrix phase material by 3D printing the lattice foams with polydomain liquid crystal elastomer (LCE), which undergo a mechanically induced phase transition under large strains. This phase transition is associated with LC mesogen rotation and alignment and provides a second mechanism for mechanical energy dissipation in addition to the viscoelastic relaxation of the polymer network. Here, we contrast the 3D printed LCE lattices with conventional, thermomechanically near-equivalent elastomer lattice foams to quantify the energy-absorbing enhancement the LCE matrix phase provides. Under cyclic quasi-static uniaxial compression conditions, the LCE lattices show dramatically enhanced energy dissipation in uniaxial compression compared to the non-LCE equivalent foams printed with a commercially available photocurable elastomer resin. The lattice geometry also plays a prominent role in determining the energy dissipation ratio between the LCE and non-LCE foams. We show that when increasing the lattice connectivity, the foam deformation transitions from bending-dominated to stretching-dominated deformations, which generates higher axial strains in the struts and higher energy dissipation in the lattice foam, as stretching allows greater mesogen rotation than bending. The LCE foams demonstrate superior energy absorption during the repeated dynamic loading during drop testing compared with the non-LCE equivalent foams, demonstrating the potential of LCEs to enhance physical protection systems against mechanical impact.

3D printing↗
NASA NTRS1987

Free wake analysis of helicopter rotor blades in hover using a finite volume technique

A fully compressible method for determining helicopter rotor wake effects is described which computes the wake without requiring external specification of the wake, or separate computations for the wake and blade region. The method is a modification of a compressible finite volume Potential Flow technique, and it has been implemented in a program, HELIX I, for computing compressible rotor flow fields in hover with free wakes. Wake positions in substantial agreement with experiment have been calculated for cases including subsonic and transonic flows, high and low aspect ratios, and two- and four-bladed rotors.

Ramachandran, K.↗
NASA NTRS1949

Two-dimensional compressible flow in turbomachines with conic flow surfaces

A general method of analysis is developed for two-dimensional, steady, compressible flow in stators or rotors of radial and mixed flow turbomachines with conic flow surfaces (surfaces of right circular cones generated by center line of flow passage in the axial-radial plane). The variables taken into account are: (1) tip speed of the rotor, (2) flow rate, (3) blade shape, (4) variation in passage height with radius, (5) number of blades, and (6) cone angle of the flow surface. Relaxation methods are used to solve the nonlinear differential equation for the stream function. Two numerical examples are presented; one for compressible and the other for incompressible flow in a centrifugal compressor with thin, straight blades. The results of these examples are given by plots of the streamlines, constant velocity-ratio lines, and constant pressure-ratio line.

Stanitz, John D↗