Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Attach”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Ablative heat shield design for space shuttle

Ablator heat shield configuration optimization studies were conducted for the orbiter. Ablator and reusable surface insulation (RSI) trajectories for design studies were shaped to take advantage of the low conductance of ceramic RSI and high temperature capability of ablators. Comparative weights were established for the RSI system and for direct bond and mechanically attached ablator systems. Ablator system costs were determined for fabrication, installation and refurbishment. Cost penalties were assigned for payload weight penalties, if any. The direct bond ablator is lowest in weight and cost. A mechanically attached ablator using a magnesium subpanel is highly competitive for both weight and cost.

Seiferth, R. W.↗
NASA NTRS1973

A method for calculating aerodynamic heating on sounding rocket tangent ogive noses.

A method is presented for calculating the aerodynamic heating and shear stresses at the wall for tangent ogive noses that are slender enough to maintain an attached nose shock through that portion of flight during which heat transfer from the boundary layer to the wall is significant. The lower entropy of the attached nose shock combined with the inclusion of the streamwise pressure gradient yields a reasonable estimate of the actual flow conditions. Both laminar and turbulent boundary layers are examined and an approximation of the effects of (up to) moderate angles-of-attack is included in the analysis. The analytical method has been programmed in FORTRAN IV for an IBM 360/91 computer.

Wing, L. D.↗
NASA NTRS1972

Investigation of mounting discrete chip components for hybrid microelectronic applications.

In the assembly of hybrid microcircuits, passive and active discrete chip components are attached by epoxy cements and by solders. This study was initiated to determine the integrity of such attachments. Alumina substrates were subjected to a group of thermal and mechanical test environments defined by test methods in MIL-STD-883. Lot samples of substrates with assembly variations were subjected to separately applied testing and to serial testing. These test methods were applied sequentially to the same lot of substrates. Epoxy cements were generally satisfactory with respect to separate tests, although sequential tests severely degraded epoxy bond strengths of all types. Bond strengths to unglazed substrates were slightly superior to those of the same components on glazed types. Solder joints were vulnerable to catastrophic failure in several environments, especially temperature cycling and thermal shock. Vibration and impact shock also produced solder joint failures.

Caruso, S. V.↗
NASA NTRS1973

Three models of the vibrating ulna.

Evaluation of the ability of three models of the ulna to predict ulnar resonant frequency. The ulna is considered to be a uniform cylindrical tube made of homogeneous isotropic material. In model I the tube is attached at each end to rigid supports by hinges, in model II the tube is attached to rigid supports by springs rather than hinges, while model III is the same as model II except for the addition of a spring-mass system simulating an accelerometer strapped to the wrist. It is found that all three models exhibit comparable effectiveness in predicting the allowed cyclic vibration frequency, although model I is marginally better than models II or III in predicting this parameter. All three models also yield relatively realistic values for Young's modulus. In terms of results, therefore, there is no clear choice between the models. However, owing to greater costs incurred with models II and III, it is concluded that model I is the most useful, even though it is the least 'realistic' of the three models evaluated.-

Jurist, J. M.↗
NASA NTRS1973

Response of panels to turbulence-induced, surface-pressure fluctuations and resulting acoustic radiation to the flow field.

The response of finite rectangular panels, excited by turbulent boundary layers and the resulting acoustical radiation into the flow field is studied. The method of normal modes and the technique of spectral analysis are used to compute the power spectra of the panel amplitude and strain response. Computed results are compared with the corresponding response measurements for panels exposed to attached and separated flows at supersonic speeds and attached flow at subsonic speeds. The thin plate and the convected wave equations are coupled through the boundary condition on the panel to give a formula for the radiation pressure power spectra. A formula for the acoustical damping ratio of the panel is obtained through the principle of virtual work.-

Chyu, W. J.↗
NASA NTRS1973

Noise tests on an externally blown flap with the engine in front of the wing

Noise tests were conducted with a nozzle exhausting over a small scale model of an externally blown flap (EBF) lift-augmentation system, with exhaust impingement on the wing leading edge. Two series of tests were conducted: with wing leading edge inside the nozzle; and with leading edge set back from the nozzle exit plane 1 diameter on the jet axis. The results indicated no significant differences in spectral shape, level, or directivity pattern. Static lift and thrust tests were conducted on the same model indicated considerable flow attachment on both configurations, with slightly greater attachment and turning for the wing outside the nozzle. Finally, a comparison with engine-above- and engine-below-the-wing EBF's tested by previous investigators shows the acoustic performance of the configurations tested for this report to lie between the other two.

Karchmer, A. M.↗
NASA NTRS1973

The vestibular system of the owl

Five owls were given vestibular examinations, and two of them were sacrificed to provide serial histological sections of the temporal bones. The owls exhibited a curious variability in the postrotatory head nystagmus following abrupt deceleration; sometimes a brisk nystagnus with direction opposite to that appropriate to the stimulus would occur promptly after deceleration. It was found also that owls can exhibit a remarkable head stability during angular movement of the body about any axis passing through the skull. The vestibular apparatus in the owl is larger than in man, and a prominent crista neglecta is present. The tectorial membrane, the cupula, and the otolithic membranes of the utricle, saccule, and lagena are all attached to surfaces in addition to the surfaces hearing hair cells. These attachments are very substantial in the utricular otolithic membrane and in the cupula.

Money, K. E.↗
NASA NTRS1974

Experimental investigation at Mach 8 of the effects of projections and cavities on heat transfer to a model of the Viking aeroshell

An experimental investigation into the aerodynamic heating on a Mars entry vehicle shape with several types of local surface distortion is presented. The configurations tested were 0.033-scale models of a spherically blunted 70 deg half-angle cone with two protuberances of different length, representing the tube leading to the gas chromograph mass spectrometer, and two aeroshell-bioshield attachment points of different size. These models were tested at free-stream Reynolds numbers per meter of 3.7 million and 17 million over an angle-of-attack range from 0 to 18 deg in the Langley Mach 8 variable density hypersonic tunnel. The phase change-coating technique was used to measure heat transfer coefficient. The long protuberance caused more severe interference heating than the short protuberance for the same conditions. When the short projection was located close to the edge of the aeroshell, the interference heating was greater than that on the same projection when located near the vertex. A significant increase in heat transfer coefficient was measured only on the larger aeroshell-bioshield attachment point.

Creel, T. R., Jr.↗
NASA NTRS1974

Small scale model static acoustic investigation of hybrid high lift systems combining upper surface blowing with the internally blown flap

A static acoustic and propulsion test of a small radius Jacobs-Hurkamp and a large radius Flex Flap combined with four upper surface blowing (USB) nozzles was performed. Nozzle force and flow data, flap trailing edge total pressure survey data, and acoustic data were obtained. Jacobs-Hurkamp flap surface pressure data, flow visualization photographs, and spoiler acoustic data from the limited mid-year tests are reported. A pressure ratio range of 1.2 to 1.5 was investigated for the USB nozzles and for the auxiliary blowing slots. The acoustic data were scaled to a four-engine STOL airplane of roughly 110,000 kilograms or 50,000 pounds gross weight, corresponding to a model scale of approximately 0.2 for the nozzles without deflector. The model nozzle scale is actually reduced to about .17 with deflector although all results in this report assume 0.2 scale factor. Trailing edge pressure surveys indicated that poor flow attachment was obtained even at large flow impingement angles unless a nozzle deflector plate was used. Good attachment was obtained with the aspect ratio four nozzle with deflector, confirming the small scale wind tunnel tests.

Cole, T. W.↗
NASA NTRS1974

Investigation of acoustic effects of leading-edge serrations on airfoils

This paper presents and interprets a series of extensive studies of the application of leading-edge serrations as a device for reducing the vortex noise radiated from stationary and rotating airfoils in low Reynolds number flow. In these studies, a variety of serrations were attached at selected locations near the leading edge of stationary and rotating airfoils. The noise levels of the airfoils were reduced considerably with the serrations attached. An explanation of the aeroacoustic flow mechanisms involved is given.

Hersh, A. S.↗
NASA NTRS1974

Vibration response of spacecraft shrouds to in-flight fluctuating pressures

Results are presented for the vibration response of a spacecraft shroud to a range of in-flight fluctuation pressures. An Atlas-Agena 15 degree cone-cylinder shroud was analyzed during the present study, and three critical flight Mach numbers were considered. At transonic Mach numbers, the aerodynamic flow over the shroud is complex, involving zones of regular attached flow, separated flow, shock wave oscillation, and modified attached flows induced by local thickening of the boundary layer. The overall shroud vibration levels for a particular Mach number were determined by initially calculating the mean square acceleration levels induced by the fluctuating pressures distributed over an individual zone, and then summing mean square acceleration levels in one-third octave bands over all zones.

Cockburn, J. A.↗
NASA NTRS1974

Subsonic and transonic hinge moment and wing bending/torsion characteristics of .015 scale space shuttle models 49-0 and 67-TS in the Rockwell International trisonic wind tunnel (IA70), volume 1

Experimental aerodynamic investigations were conducted on an 0.015-scale representation of the integrated space shuttle launch vehicle in the trisonic wind tunnel. The primary test objective was to obtain subsonic and transonic elevon and bodyflap hinge moments and wing bending-torsion moments in the presence of the launch vehicle. Wing pressures were also recorded for the upper and lower right wing surfaces at two spanwise stations. The hinge moment, wing bending/torsion moments and wing pressure data were recorded over an angle-of-attack (alpha) range from -8 deg to +8 deg, and angle-of-sideslip (beta) range from -8 deg to +8 deg and at Mach numbers of 0.90, 1.12, 1.24 and 1.50. Tests were also conducted to determine the effects of the orbiter rear attach cross beam and the forward attach wedge and strut diameter. The orbiter alone was tested at 0.90 and 1.24 Mach number only.

Hughes, M. T.↗
NASA NTRS1974

Triple balance test of the PRR baseline space shuttle configuration on a .004 scale model of the MCR 0074 orbiter configuration in the MSFC 14 x 14 inch Trisonic Wind Tunnel (TWT 570) IA31F(B), volume 1

A wind tunnel force and moment test of the space shuttle launch vehicle was conducted. The wind tunnel model utilized a triple balance such that component aerodynamics of the orbiter, external tank, and solid rocket booster was obtained. The test was conducted at an angle of attack range from -10 deg to 10 deg, and angle of sideslip range from -10 deg to 10 deg, and a Mach number range from 0.6 to 4.96. Simulation parameters to be used in future launch vehicle wind tunnel tests were investigated. The following were included: (1) effect of orbiter -ET attach hardware; (2) model attachment (spacer) effects; (3) effects of grit on model leading surfaces; and (4) model misalignment effects. The effects of external tank nose shape was studied by investigating five different nose configurations. Plotted and tabulated data is reported.

Ramsey, P. E.↗
NASA NTRS1972

An investigation of rooftop STOL port aerodynamics

An investigation into aerodynamic problems associated with large building rooftop STOLports was performed. Initially, a qualitative flow visualization study indicated two essential problems: (1) the establishment of smooth, steady, attached flow over the rooftop, and (2) the generation of acceptable crosswind profile once (1) has been achieved. This study indicated that (1) could be achieved by attaching circular-arc rounded edge extensions to the upper edges of the building and that crosswind profiles could be modified by the addition of porous vertical fences to the lateral edges of the rooftop. Important fence parameters associated with crosswind alteration were found to be solidity, fence element number and spacing. Large scale building induced velocity fluctuations were discovered for most configurations tested and a possible explanation for their occurrence was postulated. Finally, a simple equation relating fence solidity to the resulting velocity profile was developed and tested for non-uniform single element fences with 30 percent maximum solidity.

Blanton, J. N.↗
NASA NTRS1975

Aerodynamic characteristics of MSFC model 454 of the 142 inch solid rocket booster tested in the LeRC 10 foot SWT at Mach numbers of 2.0 and 2.7 (SA6F)

A 2.112 percent scale Space Shuttle Solid Rocket Booster (SRB) was tested in a ten foot, supersonic wind tunnel. The test Mach numbers were 2.0 and 2.7. Test angles of attack were from minus 5 degrees to plus 185 degrees. The Reynolds numbers ranged from 0.514 to 2.81 million per foot. Test roll angles were 0, 22.5, 45, 90, and 135 degrees. The following configurations were tested: (1) SRB without external protuberances, (2) SRB with an electrical tunnel and a thrust attachment structure, (3) SRB with two engine shroud strakes, (4) SRB with eight engine shroud strakes, and (5) SRB with an electrical tunnel, thrust attachment structure, eight engine shroud strakes, and separation motors.

Johnson, J. D.↗
NASA NTRS1975

Deployable Heat Pipe Radiator

A 1.2- by 1.8-m variable conductance heat pipe radiator was designed, built, and tested. The radiator has deployment capability and can passively control Freon-21 fluid loop temperatures under varying loads and environments. It consists of six grooved variable conductance heat pipes attached to a 0.032-in. aluminum panel. Heat is supplied to the radiator via a fluid header or a single-fluid flexible heat pipe header. The heat pipe header is an artery design that has a flexible section capable of bending up to 90 degrees. Radiator loads as high as 850 watts were successfully tested. Over a load variation of 200 watts, the outlet temperature of the Freon-21 fluid varied by 7 F. An alternate control system was also investigated which used a variable conductance heat pipe header attached to the heat pipe radiator panel.

Edelstein, F.↗
NASA NTRS1975

Reentry static stability characteristics of a (Model 471) .005479-scale 146-inch solid rocket booster tested in the NASA/MSFC 14 by 14 inch TWT (SA8F)

A force test of a scale model of the Space Shuttle Solid Rocket Booster was conducted in a trisonic wind tunnel. The model was tested with such protuberances as a camera capsule, electrical tunnel, attach rings, aft separation rockets, ET attachment structure, and hold-down struts. The model was also tested with the nozzle at gimbal angles of 0, 2.5, and 5 degrees. The influence of a unique heat shield configuration was also determined. Some photographs of model installations in the tunnel were taken and are included. Schlieren photography was utilized for several angles of attack.

Johnson, J. D.↗
NASA NTRS1975

Wind-tunnel investigation of surface-pressure fluctuations associated with aircraft buffet

Fluctuating pressures and forces that cause aircraft buffeting have been measured on a semispan rigid-wing model of a typical variable-sweep fighter-type aircraft at transonic speeds. The rms spectral and spatial correlation characteristics of wing fluctuating pressures, fluctuating pressure summations, and structural responses are presented and discussed for a Mach number of 0.85, wing sweep angles of 26 and 72 deg, and angles of attack up to 12 deg. The fluctuating pressure characteristics beneath wing shock waves and leading-edge vortices and in regions of attached and separated flows are presented. Results indicate that: (1) the mean and fluctuating static pressure characteristics are related; (2) a circulation oscillation exists for attached flow conditions below buffet onset; and (3) a significant coupling exists between the wing shock-wave oscillation and the wing first torsional mode when shock-induced separation is present.

Riddle, D. W.↗