Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ACOUSTIC VIBRATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Some results of the testing of a full-scale Ogee tip helicopter rotor; acoustics, loads, and performance

Full-scale tests were utilized to investigate the effect of the Ogee tip on helicopter rotor acoustics, performance, and loads. Two facilities were used for this study: the Langley whirl tower and a UH-1H helicopter. The test matrix for hover on the whirl tower involved thrust values from 0 to 44,480 N (10,000 lbs) at several tip Mach numbers for both standard and Ogee rotors. The full-scale testing on the UH-1H encompassed the major portion of the flight envelope for that aircraft. Both near-field acoustic measurements as well as far-field flyover data were obtained for both the Ogee and standard rotors. Data analysis of the whirl-tower test shows that the Ogee tip does significantly diffuse the tip vortex while providing some improvement in hover performance. Flight testing of both rotors indicates that the strong impulsive noise signature of the standard rotor can be reduced with the Ogee rotor. Forward flight performance was significantly improved with the Ogee configuration for a large number of flight conditions. Further, rotor control loads and vibrations were reduced through use of this advanced tip rotor.

Mantay, W. R.↗

Measurements of energy exchange between acoustic fields and non-uniform steady flow fields

Data were obtained for a resonance tube having a vent at the center in the lateral boundary, an average flow being introduced at the ends. Experiments were done for both circular and slot vents, over ranges of both frequency and Mach number. It was demonstrated that a subsonic exhaust vent in the lateral boundary of a cold flow resonance tube provides a gain of acoustic energy for the fundamental mode within the resonance tube. The gain of acoustic energy increases approximately linearly with the Mach number, as predicted by the one-dimensional analysis. The one-dimensional result gives the values for the slope representing the variation of the attenuation coefficient of the exhaust vent with respect to the average Mach number of the flow within roughly 30% of those measured. It has been verified that the subsonic vent produces a gain proportional to the average Mach number, proportional to the frequency, and independent of the shape. The results may be applicable to the study of vibration phenomena in solid propellant rocket engines.

Magiawala, K. R.↗

Diagnostics and Active Control of Aircraft Interior Noise

This project deals with developing advanced methods for investigating and controlling interior noise in aircraft. The work concentrates on developing and applying the techniques of Near Field Acoustic Holography (NAH) and Principal Component Analysis (PCA) to the aircraft interior noise dynamic problem. This involves investigating the current state of the art, developing new techniques and then applying them to the particular problem being studied. The knowledge gained under the first part of the project was then used to develop and apply new, advanced noise control techniques for reducing interior noise. A new fully active control approach based on the PCA was developed and implemented on a test cylinder. Finally an active-passive approach based on tunable vibration absorbers was to be developed and analytically applied to a range of test structures from simple plates to aircraft fuselages.

Fuller, C. R.↗

Laboratory test and acoustic analysis of cabin treatment for propfan test assessment aircraft

An aircraft cabin acoustic enclosure, built in support of the Propfan Test Assessment (PTA) program, is described. Helmholtz resonators were attached to the cabin trim panels to increase the sidewall transmission loss (TL). Resonators (448) were located between the trim panels and fuselage shell. In addition, 152 resonators were placed between the enclosure and aircraft floors. The 600 resonators were each tuned to a 235 Hz resonance frequency. After flight testing on the PTA aircraft, the enclosure was tested in the Kelly Johnson R and D Center Acoustics Lab. Laboratory noise reduction (NR) test results are discussed. The enclosure was placed in a Gulfstream 2 fuselage section. Broadband (138 dB overall SPL) and tonal (149 dB overall SPL) excitations were used in the lab. Tonal excitation simulated the propfan flight test excitation. The fundamental tone was stepped in 2 Hz intervals from 225 through 245 Hz. The resonators increase the NR of the cabin walls around the resonance frequency of the resonator array. The effects of flanking, sidewall absorption, cabin adsorption, resonator loading of trim panels, and panel vibrations are presented. Increases in NR of up to 11 dB were measured.

Kuntz, H. L.↗

The second filter’s second coming

We measured sound-evoked vibrations at the stereociliary side of inner and outer hair cells and their surrounding supporting cells, using optical coherence tomography interferometry in living anesthetized guinea pigs. Our measurements demonstrate a gradient in frequency tuning among different cell types, going from a high best frequency at the inner hair cells to a lower one at the Hensen cells. This causes the locus of maximum inner hair cell activation to be shifted toward the apex of the cochlea as compared to the outer hair cells. These observations show that additional processing and filtering of acoustic signals occurs within the organ of Corti prior to inner hair cell excitation, thus reinstating a transformed second filter as a mechanism contributing to cochlear frequency tuning.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A modified VAPEPS method for predicting vibroacoustic response of unreinforced mass loaded honeycomb panels

VAPEPS (VibroAcoustic Payload Environment Prediction System) is a computer program used to predict the vibroacoustic response of a structure. An alternate VAPEPS modeling technique, the Modified NASA Lewis Method, is an improvement for modeling unreinforced mass loaded honeycomb panels. The Modified NASA Lewis Method prediction is compared to the standard ASMS VAPEPS prediction, and the acoustic test data for three spacecraft panels. An analytical method of computing variance is presented and used to compute 95 percent confidence levels. These levels are compared to the standard VAPEPS confidence levels and to the envelope of the test data. As a result of using the new methodology suggested in the paper, both the mean prediction and the 95 percent confidence level prediction agree well with the test data in both spectral shape and magnitude. Therefore, the Modified NASA Lewis Method prediction methodology may be used to define more realistic random vibration test levels.

Mcnelis, Mark E.↗

A modified VAPEPS method for predicting vibroacoustic response of unreinforced mass loaded honeycomb panels

VAPEPS (vibroAcoustic Payload Environment Prediction System) is a computer program used to predict the vibroacoustic response of a structure. An alternate VAPEPS modeling technique, the Modified NASA Lewis Method, is an improvement for modeling unreinforced mass loaded honeycomb panels. The Modified NASA Lewis Method prediction is compared to the standard ASMS VAPEPS prediction, and the acoustic test data for three spacecraft panels. An analytical method of computing variance is presented and used to compute 95 percent confidence levels. These levels are compared to the standard VAPEPS confidence levels and to the envelope of the test data. As a result of using the new methodology suggested in the paper, both the mean prediction and the 95 percent confidence level prediction agree well with the test data in both spectral shape and magnitude. Therefore, the Modified NASA Lewis Method prediction methodology may be used to define more realistic random vibration test levels.

Mcnelis, Mark E.↗

CO and the Temperature Structure of the Solar Atmosphere

The surface layers of the Sun provide a crucial boundary condition for many of the processes that occur in the deep interior. The stratification of the outer solar atmosphere once was thought to be well understood. However, studies of thermally sensitive molecular absorptions in the infrared revealed puzzling anomalies. Strong lines of the CO fundamental vibration-rotation bands near 5 microns showed very cool temperatures at the extreme limb, and remarkable off-limb emissions extending well into the supposedly hot chromosphere. The conflicting pictures of the photosphere/chromosphere interface, from the widely separated wavelength regimes, has raised suspicions that those "layers" of the atmosphere are much more inhomogeneous than previously suspected. One proposal is that the low chromosphere is dominated by cool gas--the "COmosphere," if you will--which is threaded by a network of persistent small-scale hot magnetic filaments and occasionally disrupted by localized acoustic disturbances. The COmosphere is capped by the merged fields of the network elements in the chromospheric "canopy." I will describe the evidence in favor of that model, including recent work at the NSO McMath-Pierce telescope (including use of the new "Phoenix" spectrometer) and translimb far-UV spectroscopy by SOHO/SUMER.

Ayres, Thomas R.↗

Investigating Response from Attached and Separated Flow Excitations on a Real Launch Vehicle using SEA

Statistical Energy Analysis (SEA) response has been fairly well anchored to test observations for Diffuse Acoustic Field (DAF) loading by others. Meanwhile, not many examples can be found in the literature anchoring the SEA vehicle panel response results to Turbulent Boundary Layer (TBL) fluctuating pressure excitations. This deficiency is especially true for supersonic trajectories such as those required by this nation s launch vehicles. Response and excitation data from vehicle flight measurements gathered during the development flight era of the Space Shuttle have been used in a trial to assess the sensitivity of response analysis to certain known and unknown parameters of the flight. This assessment compares vibration response predictions for TBL excitations produced by the SEA tool to flight measurements. A secondary, but perhaps more important objective, is to provide more clarity concerning the accuracy and conservatism that can be expected from response estimates to TBL-excited vehicle models in SEA. What range of parameters must be included in such an analysis in order to land on the conservative side in response predictions? What is the variability produced in the results with changes in these parameters? The TBL fluid structure loading model used for this study is provided from the SEA module of the commercial code VA One.

Harrison, Phil↗

Slow dynamics in a single bead with mechanical conditioning and transient heating

The contact stiffness of an aluminum bead confined between two slabs diminishes upon mechanical conditioning, and then recovers like log(t) after the conditioning ceases. Here that structure is evaluated for its response to transient heating and cooling, with and without accompanying conditioning vibrations. It is found that, under heating or cooling alone, stiffness changes are mostly consistent with temperature dependent material moduli; there is little or no slow dynamics. Hybrid tests in which vibration conditioning is followed by heating or cooling lead to recoveries that begin like log(t) and then become more complex. On subtracting the known response to heating or cooling alone we discern the influence of higher or lower temperatures on slow dynamic recovery from vibrations. It is found that heating accelerates the initial log(t) recovery, but by an amount more than predicted by an Arrhenius model of thermally activated barrier penetrations. Furthermore, transient cooling has no discernable effect, in contrast to the Arrhenius prediction that it slows recovery.

36 MATERIALS SCIENCE↗

Electron-phonon coupling and superconductivity in the doped topological crystalline insulator ( Pb 0.5 Sn 0.5 ) 1 – x In x Te

Here, we present a neutron-scattering study of phonons in single crystals of ( Pb 0.5 Sn 0.5 ) 1 – x In x Te with x = 0 (metallic, but nonsuperconducting) and x = 0.2 (nonmetallic normal state, but superconducting). We map the phonon dispersions (more completely for x = 0 ) and find general consistency with theoretical calculations, except for the transverse and longitudinal optical (LO) modes at the Brillouin-zone center. At low temperature, both modes are strongly damped but sit at a finite energy ( ≈ 4 meV in both samples), shifting to higher energy at room temperature. These modes are soft due to a proximate structural instability driven by the sensitivity of Pb-Te and Sn-Te p -orbital hybridization to off-center displacements of the metal atoms. The impact of the soft optical modes on the low-energy acoustic modes is inferred from the low thermal conductivity, especially at low temperature. Given that the strongest electron-phonon coupling is predicted for the LO mode, which should be similar for both studied compositions, it is intriguing that only the In-doped crystal is superconducting. In addition, we observe elastic diffuse (Huang) scattering that is qualitatively explained by the difference in Pb-Te and Sn-Te bond lengths within the lattice of randomly distributed Pb and Sn sites. We also confirm the presence of anomalous diffuse low-energy atomic vibrations that we speculatively attribute to local fluctuations of individual Pb atoms between off-center sites.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Active–Source Seismic Tomography at the Brady Geothermal Field, Nevada, with Dense Nodal and Fiber–Optic Seismic Arrays

We deployed a dense seismic array to image the shallow structure in the injection area of the Brady Hot Springs geothermal power plant in western Nevada. The array was composed of 238 three-component, 5 Hz nodal instruments, 8700 m of distributed acoustic sensing (DAS) fiber-optic cable (FOC) installed horizontally in surface trenches, and 400 m of FOC installed vertically in a borehole. The geophone array had about 60 m instrument spacing in the target zone, whereas DAS channel separations were about 1 m with an averaging (gauge) length of 10 m. The acquisition systems provided 15 days of continuous records, including active-source and ambient noise signals. A large vibroseis truck was operated at 196 locations, exciting a swept-frequency signal from 5 to 80 Hz over 20 s using three vibration modes (vertical, longitudinal, and transverse), with three sweeps per mode at each site. Sweeps were repeated up to four times at each site during four different stages of power plant operation: normal operation, shutdown, high and oscillatory injection and production, and normal operation. After removal of the sweep signal from the raw data, the first P-wave arrivals were automatically picked using a combination of methods. Here, the travel times were then used to invert for the 3D P-wave velocity structure. Models with 100 m horizontal and 20–50 m vertical node spacing were obtained, covering an area 2000 m by 1300 m, with acceptable resolution extending to about 250 m below surface. The travel-time data were fit to a root mean square (rms) misfit of 31 ms, close to our estimated picking uncertainty. Lateral boundaries between high and low velocity zones agree relatively well with the location of local faults from previous studies, and low near-surface velocities are associated with faults and fumarole locations. A sharp increase in velocity from < 1500 to > 2000 m/s at approximately 50 m below the ground surface in many parts of the study area may indicate a shallower water table than expected for the region.

15 GEOTHERMAL ENERGY↗

Evaluation of nature and intensity of fire concrete spalling by frequency analysis of sound records

Highlights: • Original sound-based NDT method to assess the spalling form and intensity within the time of the test is proposed. • Frequency analysis of recorded sound provides a quantitative and qualitative assessment of concrete propensity to spalling. • Nature of fire concrete spalling can be categorized by a well-defined frequency value. • Waveform and spectrogram analysis delivers information on the exact number of spalling events within the performed test. The paper presents a new method for identifying the form and intensity of spalling using an analysis of the acoustic signal emitted by concrete. To assess the intensity and monitor the course of concrete spalling during fire exposure, the analysis of the recorded sound from the furnace chamber is used. The spalling intensity was determined based on signal amplitude analysis. Investigation of sound records showed that the character of spalling can be categorized by a well-defined frequency value. Based on the analysis of the Fast Fourier Transform (FFT) spectrum, the authors have distinguished the following phenomena that are the source of the signal by assigning the corresponding frequency of the sound wave vibration: explosive spalling, aggregate spalling and destructive spalling.

36 MATERIALS SCIENCE↗

Health Monitoring of Composite Material Structures using a Vibrometry Technique

Large composite material structures such as aircraft and Reusable Launch Vehicles (RLVS) operate in severe environments comprised of vehicle dynamic loads, aerodynamic loads, engine vibration, foreign object impact, lightning strikes, corrosion, and moisture absorption. These structures are susceptible to damage such as delamination, fiber breaking/pullout, matrix cracking, and hygrothermal strain. To ensure human safety and load-bearing integrity, these structures must be inspected to detect and locate often invisible damage and faults before becoming catastrophic. Moreover, nearly all future structures will need some type of in-service inspection technique to increase their useful life and reduce maintenance and overall costs. Possible techniques for monitoring the health and indicating damage on composite structures include: c-scan, thermography, acoustic emissions using piezoceramic actuators or fiber-optic wires with gratings, laser ultrasound, shearography, holography, x-ray, and others. These techniques have limitations in detecting damage that is beneath the surface of the structure, far away from a sensor location, or during operation of the vehicle. The objective of this project is to develop a more global method for damage detection that is based on structural dynamics principles, and can inspect for damage when the structure is subjected to vibratory loads to expose faults that may not be evident by static inspection. A Transmittance Function Monitoring (TFM) method is being developed in this project for ground-based inspection and operational health monitoring of large composite structures as a RLV. A comparison of the features of existing health monitoring approaches and the proposed TFM method is given.

Schulz, Mark J.↗

Effect of Blowing on Boundary Layer of Scarf Inlet

When aircraft operate in stationary or low speed conditions, airflow into the engine accelerates around the inlet lip and pockets of turbulence that cause noise and vibration can be ingested. This problem has been encountered with engines equipped with the scarf inlet, both in full scale and in model tests, where the noise produced during the static test makes it difficult to assess the noise reduction performance of the scarf inlet. NASA Langley researchers have implemented boundary layer control in an attempt to reduce the influence of the flow nonuniformity in a 12-in. diameter model of a high bypass fan engine mounted in an anechoic chamber. Static pressures and boundary layer profiles were measured in the inlet and far field acoustic measurements were made to assess the effectiveness of the blowing treatment. The blowing system was found to lack the authority to overcome the inlet distortions. Methods to improve the implementation of boundary layer control to reduce inlet distortion are discussed.

Gerhold, Carl H.↗

Fluid-structure interactions in compressible cavity flows

Experiments were performed to understand the complex fluid-structure interactions that occur during aircraft internal store carriage. A cylindrical store was installed in a rectangular cavity having a length-to-depth ratio of 3.33 and a length-to-width ratio of 1. The Mach number ranged from 0.6 to 2.5 and the incoming boundary layer was turbulent. Fast-response pressure measurements provided aeroacoustic loading in the cavity, while triaxial accelerometers provided simultaneous store response. Despite occupying only 6% of the cavity volume, the store significantly altered the cavity acoustics. The store responded to the cavity flow at its natural structural frequencies, and it exhibited a directionally dependent response to cavity resonance. Specifically, cavity tones excited the store in the streamwise and wall-normal directions consistently, whereas a spanwise response was observed only occasionally. Also, the streamwise and wall-normal responses were attributed to the longitudinal pressure waves and shear layer vortices known to occur during cavity resonance. Although the spanwise response to cavity tones was limited, broadband pressure fluctuations resulted in significant spanwise accelerations at store natural frequencies. As a result, the largest vibrations occurred when a cavity tone matched a structural natural frequency, although energy was transferred more efficiently to natural frequencies having predominantly streamwise and wall-normal motions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Subterahertz Longitudinal Phonon Modes Propagating in a Lipid Bilayer Immersed in an Aqueous Medium

The properties of subterahertz longitudinal acoustic phonon modes in the hydrophobic region of a lipid bilayer immersed in a compressible viscous aqueous medium are investigated theoretically. An approximate expression is obtained for the Mandelstam–Brillouin components of the dynamic structure factor of a bilayer. The analysis is based on a generalized hydrodynamic model of the “two-dimensional lipid bilayer + three-dimensional fluid medium” system, as well as on known sharp estimates for the frequencies and lifetimes of long-wavelength longitudinal acoustic phonons in a free hydrated lipid bilayer and in water, obtained from inelastic X-ray scattering experiments and molecular dynamics simulations. It is shown that, for characteristic values of the parameters of the membrane system, subterahertz longitudinal phonon-like excitations in the hydrophobic part of the bilayer are underdamped. In this case, the contribution of the viscous flow of the aqueous medium to the damping of a longitudinal membrane mode is small compared with the contribution of the lipid bilayer. Quantitative estimates of the damping ratio agree well with the experimental results for the vibration mode of the enzyme lysozyme in aqueous solution [1]. It is also shown that a coupling between longitudinal phonon modes of the bilayer and relaxation processes in its fluid environment gives rise to an additional peak in the scattering spectrum, which corresponds to a non-propagating mode.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Use of HART-II Measured Motion in CFD

This presentation examines the use of HART-II measured rotor blade motion in computational fluid dynamics (CFD). Historically, comprehensive analyses were used for input to acoustic calculations. These analyses focused on lifting line aerodynamics and beam models. However, there is a a need to evolve lifting line aerodynamics to first principles, notably the use of CFD instead of lifting line. The current analysis focuses on CFD and computational structural dynamics (CSD) coupling. Beam models are still very good (CSD is typically from comprehensive analysis), but generally CFD replaced aerodynamics in comprehensive analysis. This presentation examines both CFD and CSD individually and includes predictions using measured motion as well as predictions using measured motion versus coupled motion and calculations of "correct" airloads, noise and vibration.

Boyd, D. Douglas, Jr.↗