Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Effects of air breathing engine plumes on SSV orbiter subsonic wing pressure distribution (OA57B), volume 1

Data were obtained during wind tunnel tests of a 0.0405-scale model of the ferry configuration of the space shuttle vehicle orbiter conducted in a low speed wind tunnel during the time period of September 18 to September 23, 1973. The primary test objective was to investigate orbiter wing pressure distributions resulting from nacelle plumes above and below the wing. Three six-engine nacelle configurations were tested. One configuration had a twin-podded nacelle mounted above each wing and the others had one mounted below each wing. Both had a centerline twin-podded nacelle mounted below the wing. Wing pressure distribution was determined by locating static pressure bugs on the upper and lower surfaces of the left wing. Pressure bugs were also located on the upper and lower surfaces of the body flap and on the B12 afterbody fairing when it was installed. Base and balance cavity pressures were recorded and a strain gage instrumented beam in the right wing measured elevon hinge moments and normal forces.

Soard, T.↗
NASA NTRSDate not supplied

Status of Mars Retropropulsion Testing in the Langley Unitary Plan Wind Tunnel

Future Mars human landings will be enabled by a powered descent phase starting at supersonic conditions, something which has never been done before on a Mars mission. Significant aerosciences challenges exist due to jet interactions between the retrorocket engine plumes, freestream flow, and vehicle that will affect the aerodynamic behavior during powered descent. Historically, wind tunnel tests have been used to study the interactions with inert gas exhaust simulants in place of rocket engines. On the computational side, flowfield simulations have been completed at full-scale conditions, but the available ground and flight data are not appropriate for calibrating computational uncertainties for aerodynamic interference on proposed Mars descent vehicles, due to insufficient data, dissimilar vehicle geometries, and disparate operating conditions. A wind tunnel test has been designed to begin addressing powered descent aerodynamics risks for large-scale human Mars entry concepts and to identify gaps in computational predictive capabilities. The test will be conducted in the NASA Langley Unitary Plan Wind Tunnel and is designed with improvements in model design and data products over past tests. The test campaign will be run using sub-scale model geometries derived from NASA powered descent reference vehicles: a blunt low lift-to-drag vehicle and a more slender geometry that generates higher unpowered lift. Both models have been fabricated and are ready for testing. The blunt model is equipped with the flexibility to examine the effects of nozzle pointing direction, number, location, size, and area ratio. The main measurements are heatshield aerodynamic interference forces and moments with a custom flow-through balance, discrete and distributed heatshield pressure, and high-speed flowfield visualization. This paper covers the test objectives, facility, models and instrumentation, and planned test matrix.

Mars↗
NASA NTRSDate not supplied

Status of Mars Retropropulsion Testing in the Langley Unitary Plan Wind Tunnel

Future Mars human landings will be enabled by a powered descent phase starting at supersonic conditions, something which has never been done before on a Mars mission. Significant aerosciences challenges exist due to jet interactions between the retrorocket engine plumes, freestream flow, and vehicle that will affect the aerodynamic behavior during powered descent. Historically, wind tunnel tests have been used to study the interactions with inert gas exhaust simulants in place of rocket engines. On the computational side, flowfield simulations have been completed at full-scale conditions, but the available ground and flight data are not appropriate for calibrating computational uncertainties for aerodynamic interference on proposed Mars descent vehicles, due to insufficient data, dissimilar vehicle geometries, and disparate operating conditions. A wind tunnel test has been designed to begin addressing powered descent aerodynamics risks for large-scale human Mars entry concepts and to identify gaps in computational predictive capabilities. The test will be conducted in the NASA Langley Unitary Plan Wind Tunnel and is designed with improvements in model design and data products over past tests. The test campaign will be run using sub-scale model geometries derived from NASA powered descent reference vehicles: a blunt low lift-to-drag vehicle and a more slender geometry that generates higher unpowered lift. Both models have been fabricated and are ready for testing. The blunt model is equipped with the flexibility to examine the effects of nozzle pointing direction, number, location, size, and area ratio. The main measurements are heatshield aerodynamic interference forces and moments with a custom flow-through balance, discrete and distributed heatshield pressure, and high-speed flowfield visualization. This paper covers the test objectives, facility, models and instrumentation, and planned test matrix.

Supersonic Retropropulsion↗
NASA NTRS1952

Performance and Operational Characteristics of a Python Turbine-propeller Engine at Simulated Altitude Conditions / Carl L. Meyer and Lavern A. Johnson

The performance and operational characteristics of a Python turbine propeller engine have been investigated over a range of engine operating conditions at simulated altitudes from 5000 to 40,000 feet in the NACA Lewis altitude wind tunnel . For the performance phase of the investigation, a single cowl-inlet ram pressure ratio was maintained and independent control of engine speed and fuel flow was used to obtain a range of power at each engine speed. Engine performance data obtained at a given altitude could not be used to predict performance accurately at other altitudes by use of the standard air pressure and temperature generalizing factors. Specific fuel consumption based on shaft horsepower decreased as the shaft horsepower increased at a given engine speed. At a given altitude condition and turbine -inlet total temperature, there was an optimum engine speed at which maximum shaft horsepower was obtained. At a given engine speed and turbine-inlet total temperature, a greater portion of the total available energy was converted to propulsive power as the altitude increased. Windmilling starts were made at altitudes up to 40,000 feet; the minimum true airspeed required for successful windmilling starts increased as the altitude was raised. In general, the engine control prevented large overshoots or undershoots of engine speed during starts, accelerations, and decelerations.

Engines - Armstrong-Siddely Python Turbo-Propeller↗
DOE OSTI2018

Analysis of Wind Speed Shear and Turbulence LiDAR Measurements to Support Offshore Wind in the Northeast United States

In this paper, we present wind speed measurements collected at 40m to 200m above sea-level to support the New England Aqua Ventus I 12 MW Floating Offshore Wind Farm to be located 17km offshore the Northeast United States. The high-altitude wind speed data are unique and represent some of the first measurements made offshore in this part of the country which is actively being developed for offshore wind. Multiple LiDAR measurements were made using a DeepCLiDAR floating buoy and LiDARs located on land on a nearby island. The LiDARs compared favorably thereby confirming the LiDAR buoy measurements. Wind speed shear profiles are presented. The measurements are compared against industry standard mesoscale model outputs and offshore design codes including the American Bureau of Shipping, American Petroleum Institute, and DNV-GL guides. Significant variation in the vertical wind speed profile occurs throughout the year. This variation is not currently addressed in offshore wind design standards which typically recommend the use of only a few values for wind shear in operational and extreme conditions. The mean wind shears recorded were also higher than industry recommended values. Additionally, turbulence measurements made from the LiDAR, although not widely accepted in the scientific community, are presented and compared against industry guidelines.

American Petroleum Institute↗
NASA NTRS1980

Should we attempt global (inlet engine airframe) control design?

The feasibility of multivariable design of the entire airplane control system is briefly addressed. An intermediate step in that direction is to design a control for an inlet engine augmentor system by using multivariable techniques. The supersonic cruise large scale inlet research program is described which will provide an opportunity to develop, integrate, and wind tunnel test a control for a mixed compression inlet and variable cycle engine. The integrated propulsion airframe control program is also discussed which will introduce the problem of implementing MVC within a distributed processing avionics architecture, requiring real time decomposition of the global design into independent modules in response to hardware communication failures.

Carlin, C. M.↗
DOE OSTI2013

Comparison of API & IEC Standards for Offshore Wind Turbine Applications in the U.S. Atlantic Ocean: Phase II - March 9, 2009 - September 9, 2009

The National Renewable Energy Laboratory (NREL) contracted MMI Engineering to conduct Phase II of the Joint Industry Project on Comparison of two design standards for offshore wind turbines (OWTs) in the United States Outer Continental Shelf waters. The two standards were the American Petroleum Institute (API) RP – 2A Recommended Practice for Planning, Designing, and Constructing Fixed Offshore Platforms and the International Electrotechnical Commission (IEC) 61400-3 Design Requirements for Offshore Wind Turbines. In Phase I, two structure types (a monopile and a tripod) were studied at two sites – offshore Texas at 24-m water depth and offshore Massachusetts at 15-m water depth. This study provided insights into the loads imposed on the structures caused by wind and ocean forces, and also provided insights into the strength (capacity) of the structures subject to these loads. The resulting reliability (annual failure probability for ultimate strength) for the two structures at the two sites were generally governed by turbine and blade resonance avoidance for designing the structure, and not by ultimate strength needs to resist extreme loads. The conclusions drawn from Phase I were based on these limited numbers of case studies. This limitation prompted the need to conduct this second phase to study two new designs, the monopile and a jacket (space frame) substructure, at the same site where ultimate strength would likely also influence design and resonance avoidance. The site selected for Phase II was the offshore Massachusetts site, but with a water depth of 25 m (instead of 15 m as in Phase I). This selection permitted the use of the same meteorological and oceanographic (metocean) parameters, with the breaking wave criteria altered as a result of the increased water depth.

17 WIND ENERGY↗
NASA NTRS1990

Compact Analyzer/Controller For Oxygen-Enrichment System

System controls hypersonic air-breathing engine tests. Compact analyzer/controller developed, built, and tested in small-scale wind tunnel prototype of the 8' HTT (High-Temperature Tunnel). Monitors level of oxygen and controls addition of liquid oxygen to enrich atmosphere for combustion. Ensures meaningful ground tests of hypersonic engines in range of speeds from mach 4 to mach 7.

Puster, Richard L.↗
NASA NTRS2004

Noise Benefits of Increased Fan Bypass Nozzle Area

An advanced model turbofan (typical of current engine technology) was tested in the NASA Glenn 9 by 15 Foot Low Speed Wind Tunnel (9-by 15-Foot LSWT) to explore far field acoustic effects of increased bypass nozzle area. This fan stage test was part of the NASA Glenn Fan Broadband Source Diagnostic Test, second entry (SDT2) which acquired aeroacoustic results over a range of test conditions. The baseline nozzle was sized to produce maximum stage performance for the engine at a high altitude, cruise point condition. However, the wind tunnel testing is conducted near sea level conditions. Therefore, in order to simulate and obtain performance at other aircraft operating conditions, two additional nozzles were designed and tested-one with a +5 percent increase in weight flow (+5.4 percent increase in nozzle area compared with the baseline nozzle), sized to simulate the performance at the stage design point conditions, and the other with a +7.5 percent increase in weight flow (+10.9 percent increase in nozzle area), sized for maximum weight flow with a fixed nozzle at sea level conditions. Measured acoustic benefits with increased nozzle area were very encouraging, showing overall sound power level (OAPWL) reductions of 2 or more dB while the stage thrust actually increased by several percentage points except fro the most open nozzle at takeoff rotor speed where stage performance decreased. These noise reduction benefits were seen to primarily affect broadband noise, and were evident throughout the range of measured sideline angles.

Woodward, Richard P.↗
DOE OSTI2024

Software-Defined Virtual Synchronous Condenser

Synchronous condensers (SCs) play important roles in integrating wind energy into relatively weak power grids. However, the design of SCs usually depends on specific application requirements and may not be adaptive enough to the frequently-changing grid conditions caused by the transition from conventional to renewable power generation. This paper devises a software-defined virtual synchronous condenser (SDViSC) method to address the challenges. Our contributions are fourfold: 1) design of a virtual synchronous condenser (ViSC) to enable full converter wind turbines to provide built-in SC functionalities; 2) engineering SDViSCs to transfer hardware-based ViSC controllers into software services, where a Tustin transformation-based software-defined control algorithm guarantees accurate tracking of fast dynamics under limited communication bandwidth; 3) a software-defined networking-enhanced SDViSC communication scheme to allow enhanced communication reliability and reduced communication bandwidth occupation; and 4) Prototype of SDViSC on our real-time, cyber-in-the-loop digital twin of large-wind-farm in an RTDS environment. Furthermore, extensive test results validate the excellent performance of SDViSC to support reliable and resilient operations of wind farms under various physical and cyber conditions.

17 WIND ENERGY↗
DOE OSTI2025

Leveraging System Dynamics to Predict the Commercialization Success of Emerging Energy Technologies: Lessons from Wind Energy

The United States urgently needs to tackle the climate crisis while enhancing energy security and resiliency. The complexity of the U.S. energy system, with its interconnected elements, makes predicting future states challenging, especially with the introduction of novel energy systems like wind, solar, clean hydrogen, and advanced nuclear technologies. Modern systems engineering methods and tools can provide deeper insights into these dynamics and future behaviors. This research aims to develop a comprehensive model that captures the main elements and behaviors of new energy technologies within the existing energy system. We hypothesized that the market uptake of novel energy systems is influenced by multiple diverse factors, such as technological learning, availability of resources, and economic incentives; examined the history of electricity generation using land-based wind technologies; and developed a system dynamics model to investigate the relationships between capacity growth and influencing factors, both internal and external. The developed model yielded outcomes that confirmed the hypothesized dynamics of wind energy system diffusion through a quantitative comparison of installed capacity and highlighted the significant influence of resource availability, federal incentives (production tax credits), and technological learning on capacity growth and cost reduction. This research aims to support informed decision-making for investments in novel energy systems and aid in developing effective policies for technology deployment.

17 WIND ENERGY↗
DOE OSTI2025

Efficient wind farm layout optimization with the FLOWERS AEP model and analytic gradients

Wind farm layout optimization (WFLO) studies often aim to maximize the annual energy production (AEP) of a wind farm by choosing an arrangement of turbines that minimizes wake interactions. One way to reduce the cost of WFLO studies is by using more computationally efficient AEP models. The cost of standard AEP modeling approaches, based on the numerical integration of low-fidelity engineering wake models, scales poorly with the number of simulated discrete wind conditions. A second way to reduce cost when using a gradient-based algorithm is to supply exact gradient information instead of finite-difference estimates. However, analytical functions for the derivatives of AEP with respect to turbine positions are not always available in the conventional modeling approach. FLOWERS is a computationally inexpensive, analytical model for wind farm AEP that is specifically developed for WFLO applications. In this paper, we analyze the performance of the FLOWERS AEP model with analytic gradients in a layout optimization study compared with a reference optimization framework across three wind farm case studies. We find that the FLOWERS-based approach reduces computation time by a factor of 50–4000 and improves optimal AEP by about 0.3% with less than half of the variability in AEP across instances with randomized initial conditions. We also find the optimal layouts to be insensitive to model parameter tuning, making FLOWERS-based layout optimization a streamlined, user-friendly approach.

17 WIND ENERGY↗
NASA NTRS1985

Static internal performance of a single-engine onaxisymmetric-nozzle vaned-thrust-reverser design with thrust modulation capabilities

An investigation has been conducted at wind-off conditions in the stati-test facility of the Langley 16-Foot Transonic Tunnel. The tests were conducted on a single-engine reverser configuration with partial and full reverse-thrust modulation capabilities. The reverser design had four ports with equal areas. These ports were angled outboard 30 deg from the vertical impart of a splay angle to the reverse exhaust flow. This splaying of reverser flow was intended to prevent impingement of exhaust flow on empennage surfaces and to help avoid inlet reingestion of exhaust gas when the reverser is integrated into an actual airplane configuration. External vane boxes were located directly over each of the four ports to provide variation of reverser efflux angle from 140 deg to 26 deg (measured forward from the horizontal reference axis). The reverser model was tested with both a butterfly-type inner door and an internal slider door to provide area control for each individual port. In addition, main nozzle throat area and vector angle were varied to examine various methods of modulating thrust levels. Other model variables included vane box configuration (four or six vanes per box), orientation of external vane boxes with respect to internal port walls (splay angle shims), and vane box sideplates. Nozzle pressure ratio was varied from 2.0 approximately 7.0.

Leavitt, L. D.↗
NASA NTRS1954

Preliminary Altitude Performance Characteristics of the J57-P-1 Turbojet Engine with Fixed-area Exhaust Nozzle

An investigation to determine the altitude performance of the J57-P-1 turbojet engine and components was conducted at the NACA Lewis altitude wind tunnel. Data were obtained over a corrected inboard rotor speed range from 56 to 106 percent of rated speed, with intercompressor bleeds both open and closed, at altitudes from 15,000 to 50,000 feet and at a flight Mach number of 0.81. The corresponding range of Reynolds number indices was from 0.858 to 0.213. All data presented were obtained with a fixed-area exhaust nozzle sized according to the manufacturer's specification. Over-all engine performance parameters are presented as functions of inboard rotor speed corrected on the basis of engine inlet temperature. Component parameters are presented as functions of their respective corrected rotor speeds. A tabulation of all performance data is included in addition to the graphical presentation. Corrected net thrust is unusually sensitive to changes in corrected inboard rotor speed in the high speed region. A change of 1 percent in speed, at sated speed, produced a change of 6 percent in corrected net thrust . At rated engine speed, increasing the altitude from 15,000 to 50,000 feet at a constant flight Mach number of 0.81 increased the specific fuel consumption 13 percent but did not affect corrected net thrust.

Bloomer, Harry E.↗