Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “virtual engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Technologies for Detecting Interactions between Current Plant Configuration States and Component Manipulations Directed by In-Use Procedures

This research effort is a part of the Light Water Reactor Sustainability (LWRS) Program, which is a research and development (R&D) program sponsored by the Department of Energy. The LWRS Program is performed in close collaboration with industry R&D programs that provide the technical foundations for licensing and managing the long term, safe, and economical operation of current nuclear power plants (NPPs). The LWRS Program serves to help the United States (U.S.) nuclear industry adopt new technologies and engineering solutions that facilitate the continued safe operation of these NPPs and extension of their current operating licenses. A new area of LWRS research, Outage Risk Management Improvement (ORMI) seeks to improve the management of nuclear power plant outages through the development of tools to assist in evaluating pending activities against requirements to detect undesired interactions. Significant efforts are expended to manage the nuclear risk of an outage. The utilities conduct pre outage risk assessments, based on a very detailed review of the outage schedule, to identify where combinations of outage work and equipment out of service would result in degraded conditions with respect to nuclear safety or regulatory compliance. Probabilistic risk assessment studies are conducted to quantify the incremental core damage frequency as a result of the outage activities and system unavailability. These studies are usually presented to site and fleet management, the site plant operational review committee, and the NPP’s independent Nuclear Safety Review Board for concurrence that the outage is planned safely and that reasonable measures have been taken to reduce the added risk of conducting the outage. During the outage, the plant configuration is monitored continuously to ensure that it conforms to the approved safety plan. Deviations must be assessed and approved by management committees and, in some cases, the plant operational review committee. In virtually all outage meetings and job briefings, the current nuclear safety status of the plant is communicated, including information on the specific equipment that is being relied on to meet the requirements of the nuclear safety plan. In addition, Operations and the Outage organizations implement several layers of physical and administrative barriers to prevent unintended interaction with the systems and equipment credited for nuclear safety. In spite of all these efforts, nuclear safety challenges still occur too frequently in outages. While some of these are due to failures of equipment credited for safety, the majority occur because of human error. These typically involve some form of interaction between work activities and plant configuration changes. Some of them are very subtle and are extremely challenging to detect in advance. Nevertheless, they are not acceptable and represent clear opportunities to improve nuclear safety during outages. This project will develop tools and strategies to minimize these interactions.

99 GENERAL AND MISCELLANEOUS↗

Spin-Controllable Dynamics in Defect-Engineered Carbon Nanotubes as Single Photon Emitters: Data-Driven Modeling and Computations

Quantum technologies, such as quantum computing and sensing, require efficient single-photon emission (SPE) sources that operate at room temperature in telecom wavelengths. While several materials can serve as SPE sources, no single platform meets all the criteria for efficiency, ambient operation, and scalability. Single-walled carbon nanotubes (SWCNTs) with covalently attached molecules offer a promising solution. Their SPE can be easily tuned via modifications of the SWCNT's diameter, chirality, and bonded molecules, enabling emission across near-IR to telecom wavelengths at ambient conditions. However, to fully realize the potential of SWCNTs and unlock their quantum capabilities, a deeper understanding of how structural defects from molecular adducts affect their emission and competing photoexcited processes is essential. To address this gap in our knowledge, this project combined quantum chemistry calculations with data-driven methods of cheminformatics (QSAR) and machine learning (ML). The developed computational approaches have provided several design strategies for covalent functionalization of SWCNTs to improve their optical response. The collaboration with Los Alamos National Lab (LANL) enabled direct comparison of computational and experimental data, facilitating method validation. This partnership was enhanced through access to LANL's Center for Integrated Nanotechnologies (CINT) utilizing User Facility Program and summer internships, which provided three NDSU graduate students with hands-on experience at LANL. The outcomes of this project included (1) Advancing the current stage of computational methods in accurate modeling of non-adiabatic spin-dependent photoexcited dynamics and its applicability to nanosystems consisting of thousands of atoms, realized as open-access codes linked to existing DFT-based software; (2) Establishing the relationship between the structure of adducts and SWCNTs and intrinsic excitonic and spin properties of defect states for guiding novel synthetic strategies and experimental probes of chemically functionalized SWCNTs as near-IR emitting materials; (3) Generating virtual libraries of hypothetical functionalized SWCNTs for virtual screening of their chemical structures and optical properties, leveraging new functionalities of SWCNTs; (4) Offering a unique experience for NDSU graduate students that prepared them for future scientific careers related to materials modeling and big data processing. These results were summarized in 12 published journal papers and 3 recently submitted papers. One of a key finding is that the position of defect sites on the SWCNT surface primarily drives the emission redshift (up to 100 meV), while the polarity of the defect-inducing molecules has a much smaller effect (~10 meV). However, the electron-donating or withdrawing properties of a molecule influence selecting reactivity of defect sites. These insights important for optimizing synthetic protocols for desired emissions in SWCNTs. We also revealed that the interaction between two defects at various positions on the SWCNT enhances the redshift and optical activity of states, favoring strong near-IR emission. This suggests that manipulations in defect concentrations is a promising strategy for controlling efficient emission. Mostly important, the defect position was found controllable by the spin states of photoexcited intermediates: Excited aromatic molecules form ortho defects with SWCNTs at their singlet states in the presence of oxygen, while oxygen-free conditions favor para defects via the triplet-state mechanism. Additionally, a heat-activated [2+2] cycloaddition reaction facilitates divalent defect formation with fewer bonding positions that narrows emission bands. These groundbreaking findings have been experimentally validated and significantly advance our understanding of defect chemistry in SWCNTs. Using a novel encoding technique and 3D-MoRSE descriptors, we developed highly accurate ML/QSAR models to predict both the 3D structure and optical properties of SWCNTs with chemical defects. This model enabled the creation of a virtual library of 125,556 structures, providing new insights into the relationship between SWCNT-defect structure and emission.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Results from the fifth galaxy serpent exercise

Galaxy Serpent is an ongoing series of virtual, web-based international tabletop exercises designed to advance the application of National Nuclear Forensics Libraries (NNFLs) in investigations involving nuclear and other radioactive material found out of regulatory control. Here, this iteration emphasized interactions between scientific teams and mock investigative entities. Participants utilized their provided NNFLs to assess material consistency with a provided database of holdings, assign confidence levels, and identify key characteristics relevant to investigative queries. The exercise highlighted both challenges encountered and lessons learned, and advanced best practices for integrating a NNFL into nuclear forensics as part of an investigation.

Database↗

GAHLS: an optimized graph analytics based high level synthesis framework

The urgent need for low latency, high-compute and low power on-board intelligence in autonomous systems, cyber-physical systems, robotics, edge computing, evolvable computing, and complex data science calls for determining the optimal amount and type of specialized hardware together with reconfigurability capabilities. With these goals in mind, we propose a novel comprehensive graph analytics based high level synthesis (GAHLS) framework that efficiently analyzes complex high level programs through a combined compiler-based approach and graph theoretic optimization and synthesizes them into message passing domain-specific accelerators. This GAHLS framework first constructs a compiler-assisted dependency graph (CaDG) from low level virtual machine (LLVM) intermediate representation (IR) of high level programs and converts it into a hardware friendly description representation. Next, the GAHLS framework performs a memory design space exploration while account for the identified computational properties from the CaDG and optimizing the system performance for higher bandwidth. The GAHLS framework also performs a robust optimization to identify the CaDG subgraphs with similar computational structures and aggregate them into intelligent processing clusters in order to optimize the usage of underlying hardware resources. Finally, the GAHLS framework synthesizes this compressed specialized CaDG into processing elements while optimizing the system performance and area metrics. Evaluations of the GAHLS framework on several real-life applications (e.g., deep learning, brain machine interfaces) demonstrate that it provides 14.27× performance improvements compared to state-of-the-art approaches such as LegUp 6.2.

97 MATHEMATICS AND COMPUTING↗

Sustainable Low-Carbon Building Materials Workshop Report

The virtual Sustainable Low-Carbon Building Materials Workshop, organized and held by the US Department of Energy’s (DOE’s) Oak Ridge National Laboratory (ORNL) on January 25, 2022, focused on identifying the technical barriers to the research, development, and deployment (RD&D) of low-carbon building materials, and on determining what can be done to overcome these technical barriers in the short-, mid-, and long-term future. The meeting brought together key players in the construction chain from industry, academia, and ORNL to promote collaborations that could help meet the goals of accelerating the development and deployment of low-carbon building materials in the United States, and of developing a net-zero (or even negative) carbon neighborhood in the Southeast United States by 2030.

36 MATERIALS SCIENCE↗

Adaptive linear predictor FIR filter based on the Cyclone V FPGA with HPS to reduce narrow band RFI in AERA radio detection of cosmic rays

We present the new approach to a filtering of radio frequency interferences (RFI) in the Auger Engineering Radio Array (AERA) which study the electromagnetic part of the Extensive Air Showers. The radio stations can observe radio signals caused by coherent emissions due to geomagnetic radiation and charge excess processes. AERA observes frequency band from 30 to 80 MHz. This range is highly contaminated by human-made RFI. In order to improve the signal to noise ratio RFI filters are used in AERA to suppress this contamination. The first kind of filter used by AERA was the Median one, based on the Fast Fourier Transform (FFT) technique. The second one, which is currently in use, is the infinite impulse response (IIR) notch filter. The proposed new filter is a finite impulse response (FIR) filter based on a linear prediction (LP). A periodic contamination hidden in a registered signal (digitized in the ADC) can be extracted and next subtracted to make signal cleaner. The FIR filter requires a calculation of n=32, 64 or even 128 coefficients (dependent on a required speed or accuracy) by solving of n linear equations with coefficients built from the covariance Toeplitz matrix. This matrix can be solved by the Levinson recursion, which is much faster than the Gauss procedure. The filter has been already tested in the real AERA radio stations on Argentinean pampas with a very successful results. The linear equations were solved either in the virtual soft-core NIOSR processor (implemented in the FPGA chip as a net of logic elements) or in the external Voipac PXA270M ARM processor. The NIOS processor is relatively slow (50 MHz internal clock), calculations performed in an external processor consume a significant amount of time for data exchange between the FPGA and the processor. Test showed a very good efficiency of the RFI suppression for stationary (long-term) contaminations. However, we observed a short-time contaminations, which could not be suppressed either by the IIR-notch filter or by the FIR filter based on the linear predictions. For the LP FIR filter the refreshment time of the filter coefficients was to long and filter did not keep up with the changes of a contamination structure, mainly due to a long calculation time in a slow processors. We propose to use the Cyclone V SE chip with embedded micro-controller operating with 925 MHz internal clock to significantly reduce a refreshment time of the FIR coefficients. The lab results are promising. (authors)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A microstructural approach to cytoskeletal mechanics based on tensegrity

Mechanical properties of living cells are commonly described in terms of the laws of continuum mechanics. The purpose of this report is to consider the implications of an alternative approach that emphasizes the discrete nature of stress bearing elements in the cell and is based on the known structural properties of the cytoskeleton. We have noted previously that tensegrity architecture seems to capture essential qualitative features of cytoskeletal shape distortion in adherent cells (Ingber, 1993a; Wang et al., 1993). Here we extend those qualitative notions into a formal microstructural analysis. On the basis of that analysis we attempt to identify unifying principles that might underlie the shape stability of the cytoskeleton. For simplicity, we focus on a tensegrity structure containing six rigid struts interconnected by 24 linearly elastic cables. Cables carry initial tension ("prestress") counterbalanced by compression of struts. Two cases of interconnectedness between cables and struts are considered: one where they are connected by pin-joints, and the other where the cables run through frictionless loops at the junctions. At the molecular level, the pinned structure may represent the case in which different cytoskeletal filaments are cross-linked whereas the looped structure represents the case where they are free to slip past one another. The system is then subjected to uniaxial stretching. Using the principal of virtual work, stretching force vs. extension and structural stiffness vs. stretching force relationships are calculated for different prestresses. The stiffness is found to increase with increasing prestress and, at a given prestress, to increase approximately linearly with increasing stretching force. This behavior is consistent with observations in living endothelial cells exposed to shear stresses (Wang & Ingber, 1994). At a given prestress, the pinned structure is found to be stiffer than the looped one, a result consistent with data on mechanical behavior of isolated, cross-linked and uncross-linked actin networks (Wachsstock et al., 1993). On the basis of our analysis we concluded that architecture and the prestress of the cytoskeleton might be key features that underlie a cell's ability to regulate its shape.

NASA Discipline Cell Biology↗

Analysis of Factors Affecting the Performance of RLV Thrust Cell Liners

The reusable launch vehicle (RLV) thrust cell liner, or thrust chamber, is a critical component of the Space Shuttle Main Engine (SSME). It is designed to operate in some of the most severe conditions seen in engineering practice. This requirement, in conjunction with experimentally observed 'dog-house' failure modes characterized by bulging and thinning of the cooling channel wall, provides the motivation to study the factors that influence RLV thrust cell liner performance. Factors or parameters believed to be directly related to the observed characteristic deformation modes leading to failure under in-service loading conditions are identified, and subsequently investigated using the cylindrical version of the higher-order theory for functionally graded materials in conjunction with the Robinson's unified viscoplasticity theory and the power-law creep model for modeling the response of the liner s constituents. Configurations are analyzed in which specific modifications in cooling channel wall thickness or constituent materials are made to determine the influence of these parameters on the deformations resulting in the observed failure modes in the outer walls of the cooling channel. The application of thermal barrier coatings and functional grading are also investigated within this context. Comparison of the higher-order theory results based on the Robinson and power-law creep model predictions has demonstrated that, using the available material parameters, the power-law creep model predicts more precisely the experimentally observed deformation leading to the 'dog-house' failure mode for multiple short cycles, while also providing much improved computational efficiency. However, for a single long cycle, both models predict virtually identical deformations. Increasing the power-law creep model coefficients produces appreciable deformations after just one long cycle that would normally be obtained after multiple cycles, thereby enhancing the efficiency of the analysis. This provides a basis for the development of an accelerated modeling procedure to further characterize dog-house deformation modes in RLV thrust cell liners. Additionally, the results presented herein have demonstrated that the mechanism responsible for deformation leading to 'dog-house' failure modes is driven by pressure, creep/relaxation and geometric effects.

Arnold, Steven M.↗

Investigations of dual-purpose canister direct disposal feasibility - 15106

Direct disposal of commercial spent nuclear fuel (SNF) in dual-purpose canisters (DPCs) could avoid the cost and complexity of re-packaging spent fuel into smaller purpose-built containers, avoid disposing of the DPC hulls as low-level waste, and potentially decrease worker dose. Technical objectives for disposal are: 1) safety of workers and the public, 2) engineering feasibility; 3) thermal management; and 4) criticality control after permanent closure of a repository. The postclosure safety case for DPC direct disposal would resemble that for any repository-waste isolation would be enhanced by choosing host geology in which radionuclide transport is diffusion dominated, and for which transport properties and pathways are insensitive to the expected temperature history. Containment functions would be assigned to the disposal overpack, and published data show that suitable materials exist for most possible disposal environments. Earlier studies showed that DPC-based waste packages would be only slightly larger and heavier than those proposed for a repository in volcanic tuff. Engineered solutions are available for transporting and emplacing them underground, although some could be the largest of their kind. The cost of DPC direct disposal in various geologic settings has been compared to options involving a change to loading standardized multi-purpose canisters, or continuing to load DPCs and re-packaging all of them for disposal. In general DPC direct disposal would cost tens of billions of dollars less, in packaging and disposal costs. Calculations for emplacement in hard rock and sedimentary rock show that host rock peak temperature targets of 100 to 200 deg.C could be met by managing fuel age and burnup, with repository closure at up to 150 years from reactor discharge. For disposal in salt, DPC-based waste packages could be emplaced at only 50 to 100 years from discharge, depending on burnup. Sedimentary media such as shales pose special challenges especially if they have low thermal conductivity. If backfill is used around DPC-based packages its peak temperature could be 150 to 200 deg.C. Without flooding of waste packages with ground water, criticality can never occur. However, some small number of disposal overpacks could fail within the postclosure performance period due to corrosion or disruptive events. Once flooded, the aluminum-based neutron absorber materials used in most DPCs would readily degrade. Analysis has shown that even without neutron absorbers, virtually all DPCs could be subcritical if flooded with chloride brines such as would occur in a salt repository. The licensing basis for existing DPCs involves criticality analysis that may be conservative compared to fuel that is actually loaded, and the difference provides uncredited reactivity margin. Uncredited margin can offset increases in reactivity associated with flooding and basket degradation. For flooding with fresh water, with loss of neutron absorbers, many DPCs have been shown to be subcritical using uncredited margin. Significantly fewer are subcritical if the fuel basket also degrades. Thus, the materials of DPC basket construction (e.g., aluminum or carbon steel) could be deleterious if they fully corrode, along with the neutron absorbers, during the performance period. Logistical simulations are used to better understand the relationship between the needed DPC decay storage time for disposal, and the timing of future events such as the repository opening date, or a transition to loading multi-purpose (disposable) canisters at nuclear power plants. Results show that the maximum benefit from implementing a new canister design, with respect to shortening the cooling time for all SNF including that in DPCs, is associated with the earliest repository start date. As time passes more of the total SNF inventory will be in DPCs such that the value of a transition to multi-purpose canisters will decline, and the remaining options are DPC direct disposal and re-packaging in purpose-designed disposal canisters. Fuel age at emplacement is of interest to evaluate potential impacts from future changes in the fuel management system that could place fuel age limits on dry storage or transportation. The minimum fuel age at emplacement (best-case) is obtained by re-packaging all DPCs into smaller canisters for disposal, thus drastically decreasing the needed decay storage time for any geologic disposal setting. If the industry transitions to smaller, multi-purpose canisters, and without re-packaging, the fuel age at emplacement would be comparable to the best case if: 1) the emplacement power limit is high enough, or 2) both the transition and the repository start date occur early (e.g., 2036 was analyzed). Technical feasibility evaluation continues to show that direct disposal could be safe and cost effective, for some DPCs and in some geologic settings. Direct disposal of a substantial fraction of existing DPCs, limited mainly by thermal management, uncredited criticality margin, materials of DPC basket construction, and the salinity of ground water in the disposal environment, could be part of the overall waste management system. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Electromagnetic enhanced ignition

Here, we investigate how EM radiation affects the thermal decomposition pathway in HMX. The experiment used an external heat source (CO 2 laser) to rapidly heat the surface of HMX and observe the response upon application of EM energy that, on its own, is not enough power to induce heating or ignition. We hypothesize that charged intermediate decomposition species and free radicals in the gas phase interact strongly with EM energy, leading to plasma formation. These gas phase species form as a result of HMX sublimation and decomposition, and will act as “virtual antennas” and strongly couple to EM energy. The rapid absorption of EM energy during this coupling event is observed in the measured reflected power data. Ignition and plasma formation were monitored using both visible and IR photodiode probes, as well as imaged using a high-speed video camera. These observations support the hypothesis that the presence of an EM field will perturb the thermal decomposition pathway of HMX, and cause ignition to occur at a lower temperature than what is predicted under typical thermal conditions. This intense interaction results in electrically excited molecules that propagate the energy and surpass the activation barrier for ignition before the predicted ignition temperature of the bulk sample has been reached. In conclusion, understanding the decomposition of energetic materials under the influence of EM energy is important to understand and predict material response under a variety of environmental conditions.

42 ENGINEERING↗

Two-color pyrometry based flame to fuel surface radiative heat flux diagnostic using flamelets

In this study, a non-intrusive two-color pyrometry based radiative heat flux diagnostic is presented that accounts for the self-absorption effects. This diagnostic relies on looking up the flame temperature and soot volume fraction using the ratio of color intensities obtained from digital cameras and numerical solutions of 1D steady-state diffusion flames. Virtual two color pyrometry of computed flame show a unique one-to-one mapping of strained flames with intensity ratio; thereby allowing flames to be indexed and creation of a two-color flamelet manifold (TCFM). The TCFM is a function of two variables; the ratio of red to green intensities (flame index) and physical distance to the stoichiometric surface defined using a level-set function. The developed diagnostic is used in upward flame spread experiments where an approximate flame hull reconstruction method is applied to provide the 3D level-set function and intensity ratio for use of TCFM to provide radiative absorption properties for 3D ray tracing. Accounting for self- absorption effects provide improved soot volume fraction estimates. In conclusion, the radiative heat flux estimates are found to be in very good agreement with literature and improved results are obtained near the flame base.

42 ENGINEERING↗

NASA's Space Health Impacts for the NASA Experience (SHINE) Training Program – Space Radiation Curriculum

In February 2023, the Space Radiation Element of the NASA Human Research Program initiated a virtual, annual space radiation curriculum. The Space Health Impacts for the NASA Experience (SHINE) Space Radiation Didactic Curriculum aims to educate participants not only in the scientific aspects of space radiation but also in the agency’s risk management strategies. SHINE Space Radiation Didactic Curriculum combined weekly seminars by speakers from NASA, other government agencies, academia, and industry, with networking sessions designed to foster collaboration between the competitively selected participants as well as interactions with NASA scientists and HRP funded investigators. The inaugural course ran weekly from February 2023 to August 2023 and was comprised of lectures, less formal coffee hours, and office hours. Each two-hour seminar sessions hosted 1-3 presentations on topics which ranged from the space radiation environment to health effects and countermeasure to granting opportunities. All lectures were recorded and will be published on the THREE (The Health Risks of Extraterrestrial Environments) website for public access (https://three.jsc.nasa.gov/). As a course requirement, participants developed individual or collaborative beam time proposals for real, proposed, or potential experiments at the NASA Space Radiation Laboratory (NSRL) at the Brookhaven National Laboratory. For the 2023 course, 25 participants were selected from a total of 59 applicants. Selected participants were citizens from 8 countries and comprised 5 graduate students, 4 postdocs, 11 scientists and 5 professors/medical doctors. Participants had a wide range of expertise including molecular and cellular biology, microbiology, botany, physiology, engineering, physics, aerospace medicine, planetary science, biostatistics, and modeling. The second annual SHINE training program is scheduled from February to August 2024. In addition, a separate SHINE Space Radiation Practicum session will be held in Fall 2024 at the NSRL. The SHINE Space Radiation Practicum is a unique opportunity that has not been available to the public since the closure of the NASA Space Radiation Summer School in 2017 and will allow a small cohort of participants competitively selected in Fall 2023 to gain hands-on radiation experience.

SHINE↗

A Multi-Dimensional Heat Transfer Model of a Tie-Tube and Hexagonal Fuel Element for Nuclear Thermal Propulsion

The Space Capable Cryogenic Thermal Engine (SCCTE) effort considers a nuclear thermal rocket design based around a Low-Enriched Uranium (LEU) design fission reactor. The reactor core is comprised of bundled hexagonal fuel elements that directly heat hydrogen for expansion in a thrust chamber and hexagonal tie-tubes that house zirconium hydride moderator mass for the purpose of thermalizing fast neutrons resulting from fission events. Created 3D steady state Hex fuel rod model with 1D flow channels. Hand Calculation were used to set up initial conditions for fluid flow. The Hex Fuel rod uses 1D flow paths to model the channels using empirical correlations for heat transfer in a pipe. Created a 2-D axisymmetric transient to steady state model using the CFD turbulent flow and Heat Transfer module in COMSOL. This model was developed to find and understand the hydrogen flow that might effect the thermal gradients axially and at the end of the tie tube where the flow turns and enters an annulus. The Hex fuel rod and Tie tube models were made based on requirements given to us by CSNR and the SCCTE team. The models helped simplify and understand the physics and assumptions. Using pipe correlations reduced the complexity of the 3-D fuel rod model and is numerically more stable and computationally more time-efficient compared to the CFD approach. The 2-D axisymmetric tie tube model can be used as a reference "Virtual test model" for comparing and improving 3-D Models.

Gomez, C. F.↗

Elucidating texture and grain morphology contributions to the micromechanical response of additively manufactured Inconel 625

Microstructural variation of additively manufactured (AM) metal components in comparison to wrought counterparts makes certification for critical applications a challenge. Microscale simulations leveraging modern computational tools may be used to supplement testing of AM microstructures, thus accelerating certification by reducing the number of experiments needed. However, as micromechanical response is closely tied to critical properties like fatigue-life and fracture, utilization of these simulations with macroscale experimental data alone is insufficient. One means to attain microscale experimental data is in situ diffraction data collected from synchrotron X-ray sources. In this work, such data were collected during in situ compression of AM Inconel 625 superalloy. Interpretation of experimental results was assisted by massive (8M element) complementary micromechanical simulations performed on sets of virtual microstructures generated using cellular automata. Together, micromechanical data from diffraction experiments and simulations were used to probe the effects of textured “track” microstructures generated during laser powder bed fusion and directional strength-to-stiffness on micromechanical response. Though fiber-averaged directional strength-to-stiffness ratios were expected to dominate given the high elastic anisotropy of the material, the combination of small variations in texture and specific grain configurations unique to AM microstructures lead to significant variability in micromechanical response after yield. The findings emphasize the importance of high-fidelity microstructural representation that captures key texture components and AM-specific morphology for property prediction of AM metals.

36 MATERIALS SCIENCE↗

Vulnerability of a VOC-Based Inverter Due to Noise Injection and Its Mitigation

Even though virtual oscillator control (VOC)-based inverters do not communicate with each other, they need to make local measurements for control. The impact of tampering with these measured or sensed signals on the performance of a VOC-based inverter and synchronization of multiple such inverters is an important but open-ended issue. As such, this letter explores the impact of intentional side-channel noise intrusion (SNI) on the synchronization of VOC-based communication-free self-synchronizing inverters (CFSIs). Two different scenarios are investigated via experimental and analytical studies using a half-bridge neutral point clamped (NPC) single-phase CFSI. Furthermore, they address the impact of SNI on the ability of a CFSI to ensure a stable 60-Hz limit cycle and on the parallel operation of two such CFSIs to ensure synchronism to a common 60-Hz load frequency.

42 ENGINEERING↗

Binder Jet Additive Multi-Material Manufacturing for the Transformational Challenge Reactor

Additive manufacturing (AM) is a process in which material is deposited in a layer-by-layer fashion, thereby building up a geometry. This contrasts with subtractive manufacturing in which material is removed from bulk feedstock to create a final geometry. Binder jet AM (BJAM) is a specific process in the AM field in which a binder, or glue, is selectively deposited on a bed of spread powder feedstock and cured. Binder is deposited with an inkjet printhead, which allows for high-resolution shaping of the powder layers. Compared with other AM processes, BJAM is fast, efficient, and scalable. Further, BJAM has one of the largest material selections of the powder AM processes as it can process ceramics, plastics, metals, and virtually any powdered material. Thus, the opportunity exists to leverage the versatility and productivity of BJAM to enable multi-material printing, the next generation of AM technology. The aim of this research is the design and manufacture of a purpose-built BJAM machine that can process multiple materials in its normal operation. This binder jet additive multi-material manufacturing (BJAM 3 ) machine will be able to produce parts that have multiple materials intra- and inter-layer. An example of this would be encapsulating metal spheres inside of a ceramic cube or vice versa. This BJAM 3 process adds another step of freedom to designing and manufacturing complex parts. The milestone for this work is to provide details on the technical progress made to date on the development of multi-material binder jetting and to facilitate simultaneous additive manufacturing of at least two different powder feedstocks.

36 MATERIALS SCIENCE↗

Diagnostic Clast-Texture Criteria for Recognition of Impact Deposits

It is difficult to find definitive evidence for impact in the geological record because there are many endogenous geological processes that can produce diamictites similar to those generated by impact ejecta. The classic impact criteria of shock fabrics in certain minerals, and iridium layers, for example, may be either difficult to find, or long-since erased from the impact site (shock fabrics also anneal with time). It is important to be able to recognize impact-generated materials in order to understand earth's crustal development and biological evolution. In future exploration of Mars and other solar-system bodies, recognition of impact materials will be important for elucidating planetary evolution, planetary volatile inventories, and exobiological issues. The cobble depicted is typical of many that have been found in diamictite deposits in Belize generated by the Chicxulub K-T impact event. The pebbles are roughly-hewn in general shape with smoothed corners and edges. Surfaces are almost uniformly frosted (on both protuberances and hollows), but some asperities are glazed. Optical microscopy and thin-section petrographic microscopy reveal the frosting to be only a few microns thick, with a well-defined granular structure; grains are the same size as those composing the bulk of the limestone, but their clearer appearance may represent annealing. One or two adjacent pebble faces are often decorated with striated gouges and closely-spaced hemispherical depressions representing indentation hollows produced by well-rounded impacting clasts of up to 0.5 cm in diameter. Some of the impactors are still embedded in the cobble surface. Non-destructive x-ray diffraction techniques showed the impactors to be of the same mineralogy as the target cobble. We believe this unusual glazing and frosting to be related to the impact event, but this must be reconciled with its survival for over 60 my. since it is composed of one of the most alterable substances, CaCO3. We focus, however, on the non-fractured rounded pebbles that appear to have impacted the larger cobble as a swarm of clasts, probably encountered during ballistic flight. It cannot be defined whether the cobble swept through the pebble cloud, or the pebbles rained upon a slowermoving cobble. Two interesting questions arise: (1) Where did large numbers of such well rounded pebbles come from in the ejecta curtain?, and (2) How did they embed themselves in a nominally brittle rock without suffering damage? Are the well-rounded pebbles crystalline (devitrified) melt spherules? Further investigations are in progress. If the cobble was cold and brittle, impact of well-rounded pebbles would have produced Hertzian fracture patterns (a) in the virtually elastically isotropic cobble target. For penetration depths of about 0.5 of the impactor diameter, the pebbles would require a relative impact velocity sufficient to cause pebble fragmentation and crushing, and the development of a complex Hertzian-Boussinesq fracture field (b) involving deep fracturing and lateral surface spalling (impact velocities > 50 m/s). The existing relationship could only evolve by the impact of cold, hard pebbles into a soft, plastic cobble surface (c). For limestone to have been plastic, it must have been at elevated temperature, but to prevent calcification of the material, the ambient pressure must also have been elevated. This would be possible either in the impact's gas plume, or within the confines of a thin aerodynamically-produced shock bow generated by supersonic ballistic motion of the cobble. In the latter case, it is implied that the cobble swept through the pebbles rather than vice-versa. Although there are high T-P conditions associated with volcanism, such textures have not been reported on volcaniclastic materials, nor from other high T-P environments; e.g., metamorphic (as far as the authors are aware). We propose that this very easily recognizable embedding and indentation surface texture can be used as a diagnostic criterion for the recognition of impact ejecta. The term "peening texture" is suggested, because it is absolutely analogous to the plastic-deformation induced, metal-surface textures generated by ball-bearing bombardment used in engineering metallurgy to work-harden metal surfaces. Additional information is contained in the original (Figures).

Marshall, J. R.↗