Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “soil depth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Solar activity during the past 10,000 years from radionuclides in lunar samples

The radionuclides Ar-37, Ar-39, H-3, and C-14 in lunar samples are related to solar activity during time periods corresponding to their mean lives. The Ar-37 activities at shallow depths vary with each Apollo mission according to the intensities of the large solar flares preceding the mission. At large depths, the Ar-37 activities are independent of solar flares and decrease with an attenuation length that is in accord with the energy spectrum of the galactic cosmic rays. The Ar-39 depth-profile differs somewhat from galactic cosmic-ray expectation; the difference may be caused by solar modulation during Maunder Minima periods. The H-3 and C-14 activities at shallow depths are considerably higher than expected from galactic cosmic rays. The high H-3 is explained by solar-flare interactions during the past 60 years. The high C-14 activities at shallow depths are caused in part by solar-flare interactions during the past 10,000 years and in part by solar-wind implantations. Solar wind-implanted C-14 is indicated by the grain-size and temperature-release dependence of C-14 in surface soil.

Fireman, E. L.↗
NASA NTRS1984

Petrologic profile of Apollo 16 regolith at Station 4

The Apollo 16 double drive tube core 64001/2 (total depth about 60 cm) consists of four petrologic units based on the modal abundance of lithic, monomineralic, and other particles in the 20-500 micron size range of samples from 12 levels. Variation in the abundance of particles derived directly from bedrocks is low and the core soils probably represent only one set of source rocks. The chemical signature of an excessively high mare basalt component at about 42 cm correlates with an excess of regolith breccias, which may then be the physical carrier. The core soils as a whole show a systematic size-composition relationship that may be attributed to a large-scale macroscopic reworking and the consequent masking of any or all previous surface process related mixing event. However, on a much smaller scale (about 0.5 cm), individual soil layers seem to have evolved more via mixing than via in situ reworking.

Basu, A.↗
NASA NTRS2000

Possibilities of Using MARSES Instrument for Long-Term Monitoring and Subsurface Studies in Arctic and Arid Lands

The Mars Electromagnetic Sounding Experiment (MARSES) is the sounding instrument developed of searching for groundwater, water-ice or permafrost layers existing in some depth under the visible surface in the dry lands of Mars. One of the more important challenges facing natural resource managers today is how to identify, measure and monitoring the cumulative impacts of land use decisions across space and time. The secondary task is to measure the soil properties of Martian subsurface, which includes porosity, electrical resistance of the liquid phase, thermal conductivity, temperature dependence. A main task of the MARSES monitoring system is to examine changes in the subsurface properties of local areas regolith on the Martian surface on the base of the database of various soil slices in terrestrial conditions. Additional information is contained in the original extended abstract.

Ozorovich, Y. R.↗
NASA NTRS2001

Possibilities of Using MARSES Instrument for Long-Term Monitoring and Subsurface Studies in Arctic and Arid Lands

The MARSES is the sounding instrument developed of searching for groundwater, water-ice or permafrost layers existing in some depth under the visible surface in the dry lands of Mars. One of the more important challenges facing natural resource managers today is how to identify, measure and monitoring the cumulative impacts of land use decisions across space and time. The secondary task is to measure the soil properties of Martian subsurface, which includes porosity, electrical resistance of the liquid phase, thermal conductivity, temperature dependence. A main task of the MARSES monitoring system is to examine changes in the subsurface properties of local areas regolith on the Martian surface on the base of the database of various soil slices in terrestrial conditions

Ozorovich, Y. R.↗
NASA NTRS2003

Evolution and Transport of Water in the Upper Regolith of Mars

Long standing theoretical predictions [1-3], as well as recent spacecraft observations [4] indicate that large quantities of ice is present in the high latitudes upper decimeters to meters of the Martian regolith. At shallower depths and warmer locations small amounts of H2O, either adsorbed or free, may be present transiently. An understanding of the evolution of water based on theoretical and experimental considerations of the processes operating at the Martian environment is required. In particular, the porosity, diffusivity, and permeability of soils and their effect on water vapor transport under Mars-like conditions have been estimated, but experimental validation of such models is lacking. Goal: Three related mechanisms may affect water transport in the upper Martian regolith. 1) diffusion along a concentration gradient under isobaric conditions, 2) diffusion along a thermal gradient, which may give rise to a concentration gradient as ice sublimes or molecules desorb from the regolith, and 3) hydraulic flow, or mass motion in response to a pressure gradient. Our combined theoretical and experimental investigation seeks to disentangle these mechanisms and determine which process(es) are dominant in the upper regolith over various timescales. A detailed one-dimensional model of the upper regolith is being created which incorporates water adsorption/ desorption, condensation, porosity, diffusivity, and permeability effects. Certain factors such as diffusivity are difficult to determine theoretically due to the wide range of intrinsic grain properties such as particle sizes, shapes, packing densities, and emergent properties such as tortuosity. An experiment is being designed which will allow us to more accurately determine diffusivity, permeability, and water desorption isotherms for regolith simulants.

Hudson, T. L.↗
DOE OSTI2022

Weathering of chlorite from grain to watershed: The role and distribution of oxidation reactions in the subsurface

The reaction mechanism of weathering of chlorite, an important rock-forming phyllosilicate, is not well understood in natural settings. Here, in this work we investigated the weathering of Fe-rich chlorite from deep protolith to saprock to soil across a small shale-underlain watershed in the Appalachian Mountains, USA (Shale Hills). We found that oxidation of Fe(II) in chlorite always occurs prior to dissolution of the interlayers of the mineral. The oxidation of pyrite and chlorite commence near the water table across narrow depth intervals under the upper-catchment ridges, but well below the water table across wide depth intervals under the valley. We hypothesize that these patterns can be explained by hydrological and geochemical differences between the ridge and the valley: oxygenated water descends sub-vertically (1D flow) under the ridge, while under the valley, oxygen-depleted water moves upward to the stream and laterally out of the watershed in the subsurface (3D flow). Geochemical and mineralogical characterization indicates that the transformation of Fe-rich chlorite at Shale Hills is initiated by the oxidation of Fe(II). Next, the interlayer hydroxide sheet dissolves to form hydroxy-interlayered vermiculite and then vermiculite. During the transformation, Mg and Fe are released into solution and Fe is reprecipitated as goethite in pore space. Delivery of oxygen to the deep subsurface by infiltration of meteoric water is thought to control the initial transformation of chlorite at Shale Hills. It is possible that weathering of many Fe(II)-rich minerals is initiated by oxidation as mediated by rates of subsurface oxygen delivery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1973

Apollo 16 neutron stratigraphy.

The Apollo 16 soils have the largest low-energy neutron fluences yet observed in lunar samples. Variations in the isotopic ratios Gd-158/Gd-157 and Sm-150/Sm-149 (up to 1.9 and 2.0%, respectively) indicate that the low-energy neutron fluence in the Apollo 16 drill stem increases with depth throughout the section sampled. Such a variation implies that accretion has been the dominant regolith 'gardening' process at this location. The data may be fit by a model of continuous accretion of pre-irradiated material or by models involving as few as two slabs of material in which the first slab could have been deposited as long as 1 b.y. ago. The ratio of the number of neutrons captured per atom by Sm to the number captured per atom by Gd is lower than in previously measured lunar samples, which implies a lower energy neutron spectrum at this site. The variation of this ratio with chemical composition is qualitatively similar to that predicted by Lingenfelter et al. (1972). Variations are observed in the ratio Gd-152/Gd-160 which are fluence-correlated and probably result from neutron capture by Eu-151.

Russ, G. P., III↗
NASA NTRS1975

Nuclear chemistry of returned lunar samples: Nuclide analysis by gamma-ray spectrometry

Primordial and cosmogenic radionuclide concentrations are determined nondestructively by gamma-ray spectrometry in soil and rock samples from the returned Apollo 17 sample collection from Taurus-Littrow and Descartes. Geochemical evidence in support of field geology speculation concerning layering of the subfloor basalt flows is demonstrated along with a possible correlation of magmatic fractionation of K/U as a function of depth. The pattern of radionuclide concentrations observed in these samples is distinct due to proton bombardment by the intense solar flares of August 4-9, 1972. Such radionuclide determinations are used in determining lunar sample orientation and characterizing solar flare activity.

Okelley, G. D.↗
NASA NTRS2005

Porous media matric potential and water content measurements during parabolic flight

Control of water and air in the root zone of plants remains a challenge in the microgravity environment of space. Due to limited flight opportunities, research aimed at resolving microgravity porous media fluid dynamics must often be conducted on Earth. The NASA KC-135 reduced gravity flight program offers an opportunity for Earth-based researchers to study physical processes in a variable gravity environment. The objectives of this study were to obtain measurements of water content and matric potential during the parabolic profile flown by the KC-135 aircraft. The flight profile provided 20-25 s of microgravity at the top of the parabola, while pulling 1.8 g at the bottom. The soil moisture sensors (Temperature and Moisture Acquisition System: Orbital Technologies, Madison, WI) used a heat-pulse method to indirectly estimate water content from heat dissipation. Tensiometers were constructed using a stainless steel porous cup with a pressure transducer and were used to measure the matric potential of the medium. The two types of sensors were placed at different depths in a substrate compartment filled with 1-2 mm Turface (calcined clay). The ability of the heat-pulse sensors to monitor overall changes in water content in the substrate compartment decreased with water content. Differences in measured water content data recorded at 0, 1, and 1.8 g were not significant. Tensiometer readings tracked pressure differences due to the hydrostatic force changes with variable gravity. The readings may have been affected by changes in cabin air pressure that occurred during each parabola. Tensiometer porous membrane conductivity (function of pore size) and fluid volume both influence response time. Porous media sample height and water content influence time-to-equilibrium, where shorter samples and higher water content achieve faster equilibrium. Further testing is needed to develop these sensors for space flight applications.

Parabolic Flight↗
DOE OSTI2021

Conceptual monopile and tower sizing for the IEA Wind Task 37 Borssele reference wind farm

This paper explores the preliminary design of the support structures for the IEA Wind Task 37 reference wind farm at the Borssele site III and IV. The study looks at two different design methods that might be used within larger wind farm system design optimization (i.e. lay-out, electrical systems, etc.). The first consists of a scaling tool that scales a detailed design according to the rated power, water depth, hub height and rotor diameter. The second is a physics-based optimization approach that relies on the WISDEM® design tool. This research compares the results of these two methods for the design of both the tower and monopile of the IEA 10-MW and 15-MW reference wind turbines at a range of sea depths (25 m, 30 m, 35 m, 40 m). The two tools yield very similar results in terms of monopile base diameter, support structure natural frequency and mass. WISDEM is then used to also investigate the sensitivity of the design to the tower top forces, wave conditions and the soil conditions. It is shown that tower top forces dominate the design. In general, large diameter structures can carry additional costs associated with manufacturing and transportation requirements. Thus, the paper is concluded with a trade-off study between mass and diameter that quantifies the effect of the reduction in monopile diameter with the increase in structural mass.

WIND ENERGY↗
NASA NTRS1974

Surface history of lunar soil and soil columns

Measurements of cosmic ray track densities are presented for soil samples from Apollo 15, 16, and 17. Median track densities are used to infer total effective exposure times within about 15 cm of the lunar surface. Minimum track densities are used to derive the time of the last impact-produced rearrangement of soil grains. For samples from near various craters ages are derived of 40 m.y. for St. George, 6 (plus or minus 3) m.y. for S. Ray, 25 to 90 m.y. for Plum, and 20 to 35 m.y. for Shorty. The material of 15003, the Apollo 15 deep core at depths of 120 to 160 cm, is inferred to have been deposited at an average rate greather than or equal to 0.35 cm/m.y. The Apollo 16 core at 41 to 47 cm depths, 60007, appears to be well mixed and was covered up by deposition at greater than 0.3 cm/m.y. for the next few m.y. after its deposition.

Fleischer, R. L.↗
NASA NTRS1999

Ciliated protozoa of two antarctic lakes: analysis by quantitative protargol staining and examination of artificial substrates

Planktonic and artificial substrate-associated ciliates have been identified in two perennially ice-covered antarctic lakes of the McMurdo Dry Valleys. Abundances estimated by quantitative protargol staining ranged from < 5 to 31690 cells l-1, levels that are comparable to those previously obtained using other methods. Nineteen ciliate taxa were identified from these lakes, with the most frequently encountered genera being Plagiocampa, Askenasia, Monodinium, Sphaerophrya and Vorticella. The taxonomic findings compare favorably with those of previous investigators; however four previously unreported genera were observed in both Lakes Fryxell and Hoare. The variability in the depth distributions of ciliates in Lake Fryxell is explained in terms of lake physicochemical properties and ciliate prey distributions, while factors related to temporal succession in the Lake Hoare assemblage remain unexplained. Local marine or temperate zone freshwater habitats are a more likely source than the surrounding dry valleys soils for present ciliate colonists in these lakes. Although the taxonomic uncertainties require further examination, our results suggest that ciliate populations in these antarctic lakes undergo significant fluctuations and are more diverse than was previously recognized.

NASA Discipline Exobiology↗
NASA NTRS2007

Probing the Depths of Space Weathering: A Cross-sectional View of Lunar Rock 76015

The term "space weathering" refers to the cumulative effects of several processes operating at the surface of any solar system body not protected by a thick atmosphere. These processes include cosmic and solar ray irradiation, solar wind implantation and sputtering, as well as melting and vaporization due to micrometeorite bombardment. Space weathering discussions have generally centered around soils but exposed rocks will also incur the effects of weathering. Rocks have much longer surface lifetimes than an individual soil grain and thus record a longer history of exposure. By studying the weathering products which have built up on a rock surface, we can gain a deeper perspective on the weathering process and better assess the relative importance of various weathering components. The weathered coating, or patina, of the lunar rock 76015 has been previously studied using SEM and TEM. It is a noritic breccia with both "glazed" (smooth glassy) and "classic" (microcratered and pancake-bearing) patina coatings. Previous TEM work on 76015 relied on ultramicrotomy to prepare cross sections of the patina coating, but these sections were limited by the "chatter" and loss of material in these brittle samples. Here we have used a focused ion beam (FIB) instrument to prepare cross sections in which the delicate stratigraphy of the patina coating is beautifully preserved.

Noble, Sarah K.↗
NASA NTRS2013

Absorption Properties of Mediterranean Aerosols Obtained from Multi-year Ground-based and Satellite Remote Sensing Observations

Aerosol absorption properties are of high importance to assess aerosol impact on regional climate. This study presents an analysis of aerosol absorption products obtained over the Mediterranean Basin or land stations in the region from multi-year ground-based AERONET and satellite observations with a focus on the Absorbing Aerosol Optical Depth (AAOD), Single Scattering Albedo (SSA) and their spectral dependence. The AAOD and Absorption Angstrom Exponent (AAE) data set is composed of daily averaged AERONET level 2 data from a total of 22 Mediterranean stations having long time series, mainly under the influence of urban-industrial aerosols and/or soil dust. This data set covers the 17 yr period 1996-2012 with most data being from 2003-2011 (approximately 89 percent of level-2 AAOD data). Since AERONET level-2 absorption products require a high aerosol load (AOD at 440 nm greater than 0.4), which is most often related to the presence of desert dust, we also consider level-1.5 SSA data, despite their higher uncertainty, and filter out data with an Angstrom exponent less than 1.0 in order to study absorption by carbonaceous aerosols. The SSA data set includes both AERONET level-2 and satellite level-3 products. Satellite-derived SSA data considered are monthly level 3 products mapped at the regional scale for the spring and summer seasons that exhibit the largest aerosol loads. The satellite SSA dataset includes the following products: (i) Multi-angle Imaging SpectroRadiometer (MISR) over 2000-2011, (ii) Ozone Monitoring Instrument (OMI) near-UV algorithm over 2004-2010, and (iii) MODerate resolution Imaging Spectroradiometer (MODIS) Deep-Blue algorithm over 2005-2011, derived only over land in dusty conditions. Sun-photometer observations show that values of AAOD at 440 nm vary between 0.024 +/- 0.01 (resp. 0.040 +/- 0.01) and 0.050 +/- 0.01 (0.055 +/- 0.01) for urban (dusty) sites. Analysis shows that the Mediterranean urban-industrial aerosols appear "moderately" absorbing with values of SSA close to approximately 0.94-0.95 +/- 0.04 (at 440 nm) in most cases except over the large cities of Rome and Athens, where aerosol appears more absorbing (SSA approximately 0.89-0.90 +/- 0.04). The aerosol Absorption Angstrom Exponent (AAE, estimated using 440 and 870 nm) is found to be larger than 1 for most sites over the Mediterranean, a manifestation of mineral dust (iron) and/or brown carbon producing the observed absorption. AERONET level-2 sun-photometer data indicate the existence of a moderate East-West gradient, with higher values over the eastern basin (AAEEast. = 1.39/AAEWest. = 1.33) due to the influence of desert dust. The North-South AAE gradient is more pronounced, especially over the western basin. Our additional analysis of AERONET level-1.5 data also shows that organic absorbing aerosols significantly affect some Mediterranean sites. These results indicate that current climate models treating organics as nonabsorbing over the Mediterranean certainly underestimate the warming effect due to carbonaceous aerosols. A~comparative analysis of the regional SSA variability has been attempted using satellite data. OMI and MODIS data show an absorbing zone (SSA approximately 0.90 at 470-500 nm) over Northeastern Africa that does not appear in the MISR retrievals. In contrast, MISR seems able to observe the East-West SSA gradient during summer, as also detected by AERONET. Also, the analysis of SSA provided by satellites indicates that the aerosol over the Mediterranean Sea appears less absorbing during spring (MAM) than summer (JJA).

satellite remote sensing observations↗
NASA NTRS2020

Brief Communication: Mapping Greenland’s Perennial Firn Aquifers Using Enhanced-Resolution L-Band Brightness Temperature Image Time Series

Enhanced-resolution L-band brightness temperature (TB) image time series generated from observations collected over the Greenland Ice Sheet by NASA’s Soil Moisture Active Passive (SMAP) satellite are used to map Greenland’s perennial firn aquifers from space. Exponentially decreasing L-band T(sub B) signatures are correlated with perennial firn aquifer areas identified via the Center for Remote Sensing of Ice Sheets (CReSIS) Multi-Channel Coherent Radar Depth Sounder (MCoRDS) that was flown by NASA’s Operation IceBridge (OIB) campaign. An empirical algorithm to map extent is developed by fitting these signatures to a set of sigmoidal curves. During the spring of 2016, perennial firn aquifer areas are found to extend over ~ 66 000 km(exp 2).

Julie Z Miller↗
NASA NTRS2012

Development of Field Excavator with Embedded Force Measurement

A semi-intelligent excavation mechanism was developed for use with the NASA-built Centaur 2 rover prototype. The excavator features a continuously rotatable large bucket supported between two parallel arms, both of which share a single pivot axis near the excavator base attached to the rover. The excavator is designed to simulate the collection of regolith, such as on the Moon, and to dump the collected soil into a hopper up to one meter tall for processing to extract oxygen. Because the vehicle can be autonomous and the terrain is generally unknown, there is risk of damaging equipment or using excessive power when attempting to extract soil from dense or rocky terrain. To minimize these risks, it is critical for the rover to sense the digging forces and adjust accordingly. It is also important to understand the digging capabilities and limitations of the excavator. This paper discusses the implementation of multiple strain gages as an embedded force measurement system in the excavator's arms. These strain gages can accurately measure and resolve multi-axial forces on the excavator. In order to validate these sensors and characterize the load capabilities, a series of controlled excavation tests were performed at Glenn Research Center with the excavator at various depths and cut angles while supported by a six axis load cell. The results of these tests are both compared to a force estimation model and used for calibration of the embedded strain gages. In addition, excavation forces generated using two different types of bucket edge (straight vs. with teeth) were compared.

Soils↗
NASA NTRS2003

Fe-Ti-Cr-Oxides in Martian Meteorite EETA79001 Studied by Point-counting Procedure Using Raman Spectroscopy

Fe-Ti-Cr-Oxide minerals contain much information about rock petrogenesis and alteration. Among the most important in the petrology of common intrusive and extrusive rocks are those of the FeO-TiO2-Cr2O3 compositional system chromite, ulv spinel-magnetite, and ilmenite-hematite. These minerals retain memories of oxygen fugacity. Their exsolution into companion mineral pairs give constraints on formation temperature and cooling rate. Laser Raman spectroscopy is anticipated to be a powerful technique for characterization of materials on the surface of Mars. A Mars Microbeam Raman Spectrometer (MMRS) is under development. It combines a micro sized laser beam and an automatic point-counting mechanism, and so can detect minor minerals or weak Raman-scattering phases such as Fe- Ti-Cr-oxides in mixtures (rocks & soils), and provide information on grain size and mineral mode. Most Fe-Ti-Cr-oxides produce weaker Raman signals than those from oxyanionic minerals, e.g. carbonates, sulfates, phosphates, and silicates, partly because most of them are intrinsically weaker Raman scatters, and partly because their dark colors limit the penetration depth of the excitation laser beam (visible wavelength) and of the Raman radiation produced. The purpose of this study is to show how well the Fe-Ti-Cr-oxides can be characterized by on-surface planetary exploration using Raman spectroscopy. We studied the basic Raman features of common examples of these minerals using well-characterized individual mineral grains. The knowledge gained was then used to study the Fe-Ti-Cr-oxides in Martian meteorite EETA79001, especially effects of compositional and structural variations on their Raman features.

Wang, Alian↗
NASA NTRS2007

Performance of a Borehole XRF Spectrometer for Planetary Exploration

We have designed and constructed a borehole XRF Spectrometer (XRFS) as part of the Mars Subsurface Access program. It will be used to determine the composition of the Mars regolith at various depths by insertion into a pre-drilled borehole. The primary performance metrics for the instrument are the lower limits of detection over a wide range of the periodic table. Power consumption during data collection was also measured. The prototype instrument is complete and preliminary testing has been performed. Terrestrial soil Standard Reference Materials were used as the test samples. Detection limits were about 10 weight parts-per-million for most elements, with light elements being higher, up to 1.4 weight percent for magnesium. Power consumption (excluding ground support components) was 12 watts.

Kelliher, Warren C.↗