SEARCH · Engineering Papers

Results for “qualitative methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

All sources NASA NTRS DOE OSTI

NASA NTRS1988

A Methodology for Multiple Rule System Integration and Resolution Within a Singular Knowledge Base

Expert Systems which support knowledge representation by qualitative modeling techniques experience problems, when called upon to support integrated views embodying description and explanation, especially when other factors such as multiple causality, competing rule model resolution, and multiple uses of knowledge representation are included. A series of prototypes are being developed to demonstrate the feasibility of automating the process of systems engineering, design and configuration, and diagnosis and fault management. A study involves not only a generic knowledge representation; it must also support multiple views at varying levels of description and interaction between physical elements, systems, and subsystems. Moreover, it will involve models of description and explanation for each level. This multiple model feature requires the development of control methods between rule systems and heuristics on a meta-level for each expert system involved in an integrated and larger class of expert system. The broadest possible category of interacting expert systems is described along with a general methodology for the knowledge representation and control of mutually exclusive rule systems.

Kautzmann, Frank N., III↗

NASA NTRS1993

An x ray scatter approach for non-destructive chemical analysis of low atomic numbered elements

A non-destructive x-ray scatter (XRS) approach has been developed, along with a rapid atomic scatter algorithm for the detection and analysis of low atomic-numbered elements in solids, powders, and liquids. The present method of energy dispersive x-ray fluorescence spectroscopy (EDXRF) makes the analysis of light elements (i.e., less than sodium; less than 11) extremely difficult. Detection and measurement become progressively worse as atomic numbers become smaller, due to a competing process called 'Auger Emission', which reduces fluorescent intensity, coupled with the high mass absorption coefficients exhibited by low energy x-rays, the detection and determination of low atomic-numbered elements by x-ray spectrometry is limited. However, an indirect approach based on the intensity ratio of Compton and Rayleigh scattered has been used to define light element components in alloys, plastics and other materials. This XRS technique provides qualitative and quantitative information about the overall constituents of a variety of samples.

Ross, H. Richard↗

DOE OSTI2023

Nonintrusive thermal-wave sensor for operando quantification of degradation in commercial batteries

Abstract Monitoring real-world battery degradation is crucial for the widespread application of batteries in different scenarios. However, acquiring quantitative degradation information in operating commercial cells is challenging due to the complex, embedded, and/or qualitative nature of most existing sensing techniques. This process is essentially limited by the type of signals used for detection. Here, we report the use of effective battery thermal conductivity ( k eff ) as a quantitative indicator of battery degradation by leveraging the strong dependence of k eff on battery-structure changes. A measurement scheme based on attachable thermal-wave sensors is developed for non-embedded detection and quantitative assessment. A proof-of-concept study of battery degradation during fast charging demonstrates that the amount of lithium plating and electrolyte consumption associated with the side reactions on the graphite anode and deposited lithium can be quantitatively distinguished using our method. Therefore, this work opens the door to the quantitative evaluation of battery degradation using simple non-embedded thermal-wave sensors.

25 ENERGY STORAGE↗

NASA NTRS2000

2D Quantum Mechanical Study of Nanoscale MOSFETs

With the onset of quantum confinement in the inversion layer in nanoscale MOSFETs, behavior of the resonant level inevitably determines all device characteristics. While most classical device simulators take quantization into account in some simplified manner, the important details of electrostatics are missing. Our work addresses this shortcoming and provides: (a) a framework to quantitatively explore device physics issues such as the source-drain and gate leakage currents, DIBL, and threshold voltage shift due to quantization, and b) a means of benchmarking quantum corrections to semiclassical models (such as density-gradient and quantum-corrected MEDICI). We have developed physical approximations and computer code capable of realistically simulating 2-D nanoscale transistors, using the non-equilibrium Green's function (NEGF) method. This is the most accurate full quantum model yet applied to 2-D device simulation. Open boundary conditions and oxide tunneling are treated on an equal footing. Electrons in the ellipsoids of the conduction band are treated within the anisotropic effective mass approximation. We present the results of our simulations of MIT 25, 50 and 90 nm "well-tempered" MOSFETs and compare them to those of classical and quantum corrected models. The important feature of quantum model is smaller slope of Id-Vg curve and consequently higher threshold voltage. Surprisingly, the self-consistent potential profile shows lower injection barrier in the channel in quantum case. These results are qualitatively consistent with ID Schroedinger-Poisson calculations. The effect of gate length on gate-oxide leakage and subthreshold current has been studied. The shorter gate length device has an order of magnitude smaller current at zero gate bias than the longer gate length device without a significant trade-off in on-current. This should be a device design consideration.

Svizhenko, Alexei↗

NASA NTRS2003

Enhancement of Mixing and Heat Transfer by Corrugated Permeable Walls

A re-circulation method that is based on the static pressure recovery in the divergent part of a converging-diverging flow channel is discussed. This method can be used to design a static device that can be used to increase the residence time of the fluid and the mixing in the transverse and/or flow directions in compressible and incompressible fluids flowing at subsonic velocities. The device with external reverse flow channels will produce mixing in both transverse and flow directions. If mixing in the flow direction is not desired, the concept can be used to design an insert to provide only transverse mixing. Theoretical relationships for a re-circulating one-dimensional incompressible flow around a converging-diverging channel were obtained. Attempts at numerical simulation of re-circulation in compressible fluids were not successful. Qualitative experimental verification of re-circulating flows for incompressible and compressible fluids were obtained.

Gilinsky, M.↗

NASA NTRS1993

Computational/experimental studies of isolated, single component droplet combustion

Isolated droplet combustion processes have been the subject of extensive experimental and theoretical investigations for nearly 40 years. The gross features of droplet burning are qualitatively embodied by simple theories and are relatively well understood. However, there remain significant aspects of droplet burning, particularly its dynamics, for which additional basic knowledge is needed for thorough interpretations and quantitative explanations of transient phenomena. Spherically-symmetric droplet combustion, which can only be approximated under conditions of both low Reynolds and Grashof numbers, represents the simplest geometrical configuration in which to study the coupled chemical/transport processes inherent within non-premixed flames. The research summarized here, concerns recent results on isolated, single component, droplet combustion under microgravity conditions, a program pursued jointly with F.A. Williams of the University of California, San Diego. The overall program involves developing and applying experimental methods to study the burning of isolated, single component droplets, in various atmospheres, primarily at atmospheric pressure and below, in both drop towers and aboard space-based platforms such as the Space Shuttle or Space Station. Both computational methods and asymptotic methods, the latter pursued mainly at UCSD, are used in developing the experimental test matrix, in analyzing results, and for extending theoretical understanding. Methanol, and the normal alkanes, n-heptane, and n-decane, have been selected as test fuels to study time-dependent droplet burning phenomena. The following sections summarizes the Princeton efforts on this program, describe work in progress, and briefly delineate future research directions.

Dryer, Frederick L.↗

NASA NTRS2015

Tetrahedral-Mesh Simulation of Turbulent Flows with the Space-Time Conservative Schemes

Direct numerical simulations of turbulent flows are predominantly carried out using structured, hexahedral meshes despite decades of development in unstructured mesh methods. Tetrahedral meshes offer ease of mesh generation around complex geometries and the potential of an orientation free grid that would provide un-biased small-scale dissipation and more accurate intermediate scale solutions. However, due to the lack of consistent multi-dimensional numerical formulations in conventional schemes for triangular and tetrahedral meshes at the cell interfaces, numerical issues exist when flow discontinuities or stagnation regions are present. The space-time conservative conservation element solution element (CESE) method - due to its Riemann-solver-free shock capturing capabilities, non-dissipative baseline schemes, and flux conservation in time as well as space - has the potential to more accurately simulate turbulent flows using unstructured tetrahedral meshes. To pave the way towards accurate simulation of shock/turbulent boundary-layer interaction, a series of wave and shock interaction benchmark problems that increase in complexity, are computed in this paper with triangular/tetrahedral meshes. Preliminary computations for the normal shock/turbulence interactions are carried out with a relatively coarse mesh, by direct numerical simulations standards, in order to assess other effects such as boundary conditions and the necessity of a buffer domain. The results indicate that qualitative agreement with previous studies can be obtained for flows where, strong shocks co-exist along with unsteady waves that display a broad range of scales, with a relatively compact computational domain and less stringent requirements for grid clustering near the shock. With the space-time conservation properties, stable solutions without any spurious wave reflections can be obtained without a need for buffer domains near the outflow/farfield boundaries. Computational results for the isotropic turbulent flow decay, at a relatively high turbulent Mach number, show a nicely behaved spectral decay rate for medium to high wave numbers. The high-order CESE schemes offer very robust solutions even with the presence of strong shocks or widespread shocklets. The explicit formulation in conjunction with a close to unity theoretical upper Courant number bound has the potential to offer an efficient numerical framework for general compressible turbulent flow simulations with unstructured meshes.

Chang, Chau-Lyan↗

DOE OSTI2025

Turbulence in Core-collapse Supernovae

It is understood in a general sense that turbulent fluid motion below the shock front in a core-collapse supernova stiffens the effective equation of state of the fluid and aids in the revival of the explosion. However, when one wishes to be precise and quantify the amount of turbulence in a supernova simulation, one immediately encounters the problem that turbulence is difficult to define and measure. Using the 3D magnetohydrodynamic code ELEPHANT, we study how different definitions of turbulence change one’s conclusions about the amount of turbulence in a supernova and the extent to which it helps the explosion. We find that, while all the definitions of turbulence we use lead to a qualitatively similar growth pattern over time of the turbulent kinetic energy in the gain region, the total amount of turbulent kinetic energy, and especially the ratios of turbulent to total kinetic energy, distinguish them. Some of the definitions appear to indicate turbulence is a necessary contributor to the explosion, and others indicate it is not. The different definitions also produce turbulence maps with different correlations with maps of the enstrophy, a quantity widely regarded as also indicating the presence of turbulence. We also compute the turbulent adiabatic index and observe that, in regions of low enstrophy, this quantity is sensitive to the definition used. As a consequence, the effective adiabatic index depends upon the method used to measure the turbulence, and thus it alters one’s conclusions regarding the impact of turbulence within the supernova.

computational astronomy↗

NASA NTRS1987

An unsteady rotor/fuselage interaction method

An analytical method has been developed to treat unsteady helicopter rotor, wake, and fuselage interaction aerodynamics. An existing lifting line/prescribed wake rotor analysis and a source panel fuselage analysis were modified to predict vibratory fuselage airloads. The analyses were coupled through the induced flow velocities of the rotor and wake on the fuselage and the fuselage on the rotor. A prescribed displacement technique was used to distort the rotor wake about the fuselage. Sensitivity studies were performed to determine the influence of wake and body geometry on the computed airloads. Predicted and measured mean and unsteady pressures on a cylindrical body in the wake of a two-bladed rotor were compared. Initial results show good qualitative agreement.

Egolf, T. Alan↗

NASA NTRS1989

Asymptotic methods for internal transonic flows

For many internal transonic flows of practical interest, some of the relevant nondimensional parameters typically are small enough that a perturbation scheme can be expected to give a useful level of numerical accuracy. A variety of steady and unsteady transonic channel and cascade flows is studied with the help of systematic perturbation methods which take advantage of this fact. Asymptotic representations are constructed for small changes in channel cross-section area, small flow deflection angles, small differences between the flow velocity and the sound speed, small amplitudes of imposed oscillations, and small reduced frequencies. Inside a channel the flow is nearly one-dimensional except in thin regions immediately downstream of a shock wave, at the channel entrance and exit, and near the channel throat. A study of two-dimensional cascade flow is extended to include a description of three-dimensional compressor-rotor flow which leads to analytical results except in thin edge regions which require numerical solution. For unsteady flow the qualitative nature of the shock-wave motion in a channel depends strongly on the orders of magnitude of the frequency and amplitude of impressed wall oscillations or fluctuations in back pressure. One example of supersonic flow is considered, for a channel with length large compared to its width, including the effect of separation bubbles and the possibility of self-sustained oscillations. The effect of viscosity on a weak shock wave in a channel is discussed.

Adamson, T. C., Jr.↗

NASA NTRS1989

Unsteady Navier-Stokes computations over airfoils using both fixed and dynamic meshes

A finite volume implicit approximate factorization method which solves the thin layer Navier-Stokes equations was used to predict unsteady turbulent flow airfoil behavior. At a constant angle of attack of 16 deg, the NACA 0012 airfoil exhibits an unsteady periodic flow field with the lift coefficient oscillating between 0.89 and 1.60. The Strouhal number is 0.028. Results are similar at 18 deg, with a Strouhal number of 0.033. A leading edge vortex is shed periodically near maximum lift. Dynamic mesh solutions for unstalled airfoil flows show general agreement with experimental pressure coefficients. However, moment coefficients and the maximum lift value are underpredicted. The deep stall case shows some agreement with experiment for increasing angle of attack, but is only qualitatively comparable past stall and for decreasing angle of attack.

Rumsey, Christopher L.↗

DOE OSTI2024

On discriminating tokamak sawtooth crash models via localized density and temperature measurements

The core electron temperature drops rapidly during the sawtooth crash in tokamak plasmas, which causes heat loss and may lead to fast particle losses or even a disruption. Several models have been proposed for the periodic crash, including the Kadomtsev model with magnetic reconnection and the quasi-interchange model with the growth of higher-mode-number pressure-driven instabilities. 3D MHD simulations were performed for these two models with a goal to develop intuition and to predict qualitatively how different types of sawtooth will appear in various diagnostics. The structures of electron density ne and electron temperature Te show a dominant (1, 1) mode for the Kadomtsev case and a dominant (4, 4) mode for the quasi-interchange case. The oscillations of ne and Te have a positive correlation near the inversion layer for both cases, while their frequencies and amplitudes are different depending on the dominant modes. Particularly, for the Kadomtsev case, we find a relation between the amount of flux reconnected during a sawtooth event and ne or Te oscillations. Therefore, we connect recently developed measurement capabilities for ne and Te to the internal sawtooth behavior. We propose that this method of analysis can help in identifying the type of sawtooth in future experiments augmented by simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS2012

Characterization of Material Response During Arc-Jet Testing with Optical Methods Status and Perspectives

The characterization of ablation and recession of heat shield materials during arc jet testing is an important step towards understanding the governing processes during these tests and therefore for a successful extrapolation of ground test data to flight. The behavior of ablative heat shield materials in a ground-based arc jet facility is usually monitored through measurement of temperature distributions (across the surface and in-depth), and through measurement of the final surface recession. These measurements are then used to calibrate/validate materials thermal response codes, which have mathematical models with reasonably good fidelity to the physics and chemistry of ablation, and codes thus calibrated are used for predicting material behavior in flight environments. However, these thermal measurements only indirectly characterize the pyrolysis processes within an ablative material pyrolysis is the main effect during ablation. Quantification of pyrolysis chemistry would therefore provide more definitive and useful data for validation of the material response codes. Information of the chemical products of ablation, to various levels of detail, can be obtained using optical methods. Suitable optical methods to measure the shape and composition of these layers (with emphasis on the blowing layer) during arc jet testing are: 1) optical emission spectroscopy (OES) 2) filtered imaging 3) laser induced fluorescence (LIF) and 4) absorption spectroscopy. Several attempts have been made to optically measure the material response of ablative materials during arc-jet testing. Most recently, NH and OH have been identified in the boundary layer of a PICA ablator. These species are suitable candidates for a detection through PLIF which would enable a spatially-resolved characterization of the blowing layer in terms of both its shape and composition. The recent emission spectroscopy data will be presented and future experiments for a qualitative and quantitative characterization of the material response of ablative materials during arc-jet testing will be discussed.

Winter, Michael↗

NASA NTRSDate not supplied

Fluid System Stability Analysis Techniques

Fluid systems, or networks, consist of multiple components that work together to achieve some desired thermofluid state. For any generic application, this fluid state can be a combination of the fluid pressure, flow rate, enthalpy, or species concentration. Fluid system components, such as pumps and valves, are often governed by nonlinear differential equations, resulting in complex component-to-component interactions. System-level fluid network stability occurs when the flow through the system can maintain a steady-state solution in the presence of small perturbations, which depends on these component interactions. System instability, however, can go undetected until issues arise during integrated system testing. This presentation explores a method for system designers to think of the fluid network as an assembly of components, each with their own thermofluid surfaces of partial stability, called nullclines. The intersections of all nullclines yields system-level solutions, called equilibrium points. When designers define operating points, they are tuning system parameters so that these equilibrium points move to the desired location in the thermofluid state plane. However, linearization theory shows us that the dynamic behavior around these points can be unstable. The local stability of these equilibrium points can be assessed analytically with eigen-analysis, or numerically by propagating state-plane samples to construct a phase portrait. Investigating a phase portrait can help designers gain a qualitative understanding of a system’s dynamic performance. This understanding can then help inform requirement definitions, component selection, and operational procedures. This presentation includes an example of the phase portrait technique on a system featuring a centrifugal pump and a back-pressure regulator (BPR). Numerical modeling of this system suggests that equilibrium points on the left-hand side of the pump curve are dynamically unstable.

Fluid System↗

NASA NTRSDate not supplied

Fluid System Stability Analysis Techniques

Fluid System↗

DOE OSTI2022

Electronic structure of α - RuCl 3 by fixed-node and fixed-phase diffusion Monte Carlo methods

Layered material α-RuCl 3 has caught wide attention due to its possible realization of Kitaev's spin liquid and its electronic structure that involves the interplay of electron-electron correlations and spin-orbit effects. Several DFT+U studies have suggested that both electron-electron correlations and spin-orbit effects are crucial for accurately describing the band gap. This work studies the importance of these two effects using fixed-node and fixed-phase diffusion Monte Carlo calculations both in spin-averaged and explicit spin-orbit formalisms. In the latter, the Slater-Jastrow trial function is constructed from two-component spin orbitals using our recent quantum Monte Carlo (QMC) developments and thoroughly tested effective core potentials. Our results show that the gap in the ideal crystal is already accurately described by the spin-averaged case, with the dominant role being played by the magnetic ground state with significant exchange and electron correlation effects. We find qualitative agreement between hybrid DFT, DFT+U, and QMC. In addition, QMC results agree very well with available experiments, and we identify the values of exact Fock exchange mixing that provide comparable gaps. Explicit spin-orbit QMC calculations reveal that the effect of spin-orbit coupling on the gap is minor, of the order of 0.2 eV, which corresponds to the strength of the spin orbit of the Ru atom.

36 MATERIALS SCIENCE↗

DOE OSTI2020

The Role of Ligand–Ligand Interactions in Multimodal Ligand Conformational Equilibria and Surface Pattern Formation

Multimodal chromatography uses multiple modes of interaction such as charge, hydrophobic, or hydrogen bonding to separate proteins. Recently, we used molecular dynamics (MD) simulations to show that ligands immobilized on surfaces can interact and associate with neighboring ligands to form hydrophobic and charge patches, which may have important implications for the nature of protein–surface interactions. Here, we study interfacial systems of increasing complexity—from a single immobilized multimodal ligand to high density surfaces—to better understand how ligand behavior is affected by the presence of a surface and the presence of other ligands in the vicinity, and how this behavior scales to larger systems. Furthermore, we find that tethering a ligand to a surface restricts its conformations to a subset of those observed in free solution, yet the ligand maintains flexibility in the plane of the surface and can form contacts with neighboring ligands. We find that although the formation of a contact between two neighboring ligands is slightly unfavorable, three neighboring ligands exhibit a preference for the formation of a fully connected cluster. To explore how these trends in ligand association extend to a larger surface with high density of ligands, we performed coarse-grained Monte Carlo (MC) simulations of a 132-ligand surface using ligand interactions parametrized based on free energies obtained from the three-ligand MD simulations. Despite their simplicity, the coarse-grained simulations qualitatively capture the cluster size distribution of ligands observed in detailed MD simulations. Quantitative differences between the two suggest opportunities for improvements in the coarse-grained energy function for efficient predictions of cluster and pattern formations. Our approach presents a promising route to the engineering of multimodal patterns for future chromatographic resin design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS2009

The Development and Implementation of a Cryogenic Pressure Sensitive Paint System in the National Transonic Facility

The Pressure Sensitive Paint (PSP) method was used to measure global surface pressures on a model at full-scale flight Reynolds numbers. In order to achieve these conditions, the test was carried out at the National Transonic Facility (NTF) operating under cryogenic conditions in a nitrogen environment. The upper surface of a wing on a full-span 0.027 scale commercial transport was painted with a porous PSP formulation and tested at 120K. Data was acquired at Mach 0.8 with a total pressure of 200 kPa, resulting in a Reynolds number of 65 x 106/m. Oxygen, which is required for PSP operation, was injected using dry air so that the oxygen concentration in the flow was approximately 1535 ppm. Results show qualitative agreement with expected results. This preliminary test is the first time that PSP has been successfully deployed to measure global surface pressures at cryogenic condition in the NTF. This paper will describe the system as installed, the results obtained from the test, as well as proposed upgrades and future tests.

Watkins, A. Neal↗