Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “potential energy surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Analysis of data from Viking RPA's

Measurements of the martian ionosphere performed by Viking Retarding Potential Analyzer (RPA) are reported. Viking RPA measurements of low energy electron fluxes out to 16,000 km above the Mars surface are discussed including both energy spectra and periods of continuous monitoring of the total flux above 15 ev. The mean electron current at energies greater than ev increases montonically by nearly two orders of magnitude from about 9000 km down to 700 km, but no clear signature of the bow shock is seen. The total wave power in the 2 sec measurement intervals for this current does, however, show a broad peak near 1700 km altitude. These variations in the low energy electron fluxes are related to whistler mode oscillations in the solar wind plasma. It is concluded that there may be a highly turbulent shock structure that masks a clear signature of the bow shock in the time averaged data.

Hanson, W. B.↗
NASA NTRS1981

Measuring the spacecraft and environmental interactions of the 8-cm mercury ion thrusters on the P80-1 mission

The subject interface measurements are described for the Ion Auxiliary Propulsion System (IAPS) flight test of two 8-cm thrusters. The diagnostic devices and the effects to be measured include: 1) quartz crystal microbalances to detect nonvolatile deposition due to thruster operation; 2) warm and cold solar cell monitors for nonvolatile and volatile (mercury) deposition; 3) retarding potential ion collectors to characterize the low energy thruster ionic efflux; and 4) a probe to measure the spacecraft potential and thruster generated electron currents to biased spacecraft surfaces. The diagnostics will also assess space environmental interactions of the spacecraft and thrusters. The diagnostic data will characterize mercury thruster interfaces and provide data useful for future applications.

Power, J. L.↗
NASA NTRS1986

Nonlocal screening in metal surfaces

Due to the effect of the nonuniform environment on the static screening of the Coulomb potential, the local-density approximation for the particle-hole interaction is found to be inadequate to determine the surface energy of simple metals. Use of the same set of single-particle states, and thus the same one-body density and the same work function, has eliminated the single-electron states in favor of the structure of the short-ranged correlations as the basis of this effect. A posteriori simplifications of the Fermi hypernetted-chain theory may be found to allow the same calculational accuracy with simpler computational tools.

Krotscheck, E.↗
NASA NTRS2014

Geology Before Pluto: Pre-Encounter Considerations

The cameras of New Horizons will provide robust data sets that should be imminently amenable to geological analysis of the Pluto systems landscapes. In this paper, we begin with a brief discussion of the planned observations by the New Horizons cameras that will bear most directly on geological interpretability. Then we broadly review the major geological processes that could potentially operate on the surfaces of Pluto and its major moon Charon. We first survey exogenic processes (i.e. those for which energy for surface modification is supplied externally to the planetary surface): impact cratering, sedimentary processes (including volatile migration), and the work of wind. We conclude with an assessment of the prospects for endogenic activity in the form of tectonics and cryovolcanism.

Pluto↗
DOE OSTI2025

PtCoO 2 for Scaled Interconnects

Copper (Cu) interconnects are an increasingly important bottleneck in integrated circuits due to energy consumption and latency caused by the notable increase in Cu resistivity as dimensions decrease, primarily due to electron scattering at surfaces. Herein, the potential of a directional conductor, PtCoO 2 , which has a low bulk resistivity and a distinctive anisotropic structure that mitigates electron surface scattering is showcased. Thin films of PtCoO 2 of various thicknesses are synthesized by molecular beam epitaxy (MBE) coupled with a postdeposition annealing process and the superior quality of PtCoO 2 films is demonstrated by multiple characterization techniques. The thickness‐dependent resistivity curve illustrates that PtCoO 2 significantly outperforms effective Cu (Cu with TaN barriers) and Ru in resistivity below 20.0 nm with a more than 6x reduction compared to effective Cu below 6.0 nm, having a value of only 6.32 μΩ cm at 3.3 nm. It is determined that grain boundary scattering can still be improved for even lower resistivities in this material system through a combination of experiments and theoretical simulations. PtCoO 2 is therefore a highly promising alternative material for future interconnect technologies promising lower resistivities, better stability, and significant improvements in energy efficiency and latency for advanced integrated circuits.

Li, Yansong [Department of Electrical Engineering ↗
NASA NTRS1994

Influence of ocean surface conditions on atmospheric vertical thermodynamic structure and deep convection

The authors analyze the influence of Sea Surface Temperature (SST) and surface wind divergence on atmospheric thermodynamic structure and the resulting effects on the occurrence of deep convection using National Meteorological Center radiosonde data and International Satellite Cloud Climatology Program data for July 1983-July 1985. The onset of deep convection requires not only the existence of positive convective available potential energy (CAPE), but also an unstable planetary boundary layer (PBL). A stable PBL is observed to suppress deep convection even when CAPE is positive. Variations of SST have a major effect on CAPE, but surface wind divergence can also affect deep convection by changing the lapse rate in the lower troposphere and humidity in the PBL. Specifically, when SST is greater than or equal to 28 C, CAPE is always positive, and surface wind divergence does not qualitatively change the buoyancy profile above the PBL. Strong surface wind divergence, however, stabilizes the PBL so as to suppress the initiation of deep convection. In warm SST regions, CAPE is greater than 0 regardless of assumptions about condensate loading, although the pseudoadiabatic limit is more consistent with the observed deep convection than the reversible moist-adiabatic limit under these circumstances. When SST is less than 27 C, CAPE is usually negative and inhibits convection, but strong surface wind convergence can destabilize the inversion layer and moisten the PBL enough to make the atmosphere neutrally stable in the mean. As a result, deep convection is generally enhanced either when SST is greater than or equal to 28 C in the absence of strong surface wind divergence or when strong surface wind convergence occurs even if SST is less than 27 C. The anomalous suppression of deep convection in the warm area of the equatorial west Pacific lying between the intertropical convergence zone (ITCZ) and south Pacific convergence zone (SPCZ) is probably caused by dryness in the PBL and an inversion in that area. The seasonal cycles of deep convection and surface wind divergence are in phase with the maximum solar radiation and lead SST for one to three months in the central Pacific. The change of PBL relative humidity plays a critical role in the changeover to convective instability in this case. The seasonal change of deep convection and associated clouds seems not to have important effects on the seasonal change of local SST in the central Pacific.

Fu, Rong↗
NASA NTRS2011

Reactive Oxygen Species on the Early Earth and Survival of Bacteria

An oxygen-rich atmosphere appears to have been a prerequisite for complex, multicellular life to evolve on Earth and possibly elsewhere in the Universe. However it remains unclear how free oxygen first became available on the early Earth. A potentially important, and as yet poorly constrained pathway, is the production of oxygen through the weathering of rocks and release into the near-surface environment. Reactive Oxygen Species (ROS), as precursors to molecular oxygen, are a key step in this process, and may have had a decisive impact on the evolution of life, present and past. ROS are generated from minerals in igneous rocks during hydrolysis of peroxy defects, which consist of pairs of oxygen anions oxidized to the valence state -1 and during (bio) transformations of iron sulphide minerals. ROS are produced and consumed by intracellular and extracellular reactions of Fe, Mn, C, N, and S species. We propose that, despite an overall reducing or neutral oxidation state of the macroenvironment and the absence of free O2 in the atmosphere, organisms on the early Earth had to cope with ROS in their microenvironments. They were thus under evolutionary pressure to develop enzymatic and other defences against the potentially dangerous, even lethal effects of oxygen and its derived ROS. Conversely it appears that microorganisms learned to take advantage of the enormous reactive potential and energy gain provided by nascent oxygen. We investigate how oxygen might be released through weathering. We test microorganisms in contact with rock surfaces and iron sulphides. We model bacteria such as Deionococcus radiodurans and Desulfotomaculum, Moorella and Bacillus species for their ability to grow or survive in the presence of ROS. We examine how early Life might have adapted to oxygen.

Balk, Melikea↗
NASA NTRS1984

Structural tests and development of a laminar flow control wing surface composite chordwise joint

The dramatic increases in fuel costs and the potential for periods of limited fuel availability provided the impetus to explore technologies to reduce transport aircraft fuel consumption. NASA sponsored the Aircraft Energy Efficiency (ACEE) program beginning in 1976 to develop technologies to improve fuel efficiency. The Lockheed-Georgia Company accomplished under NAS1-16235 Laminar-Flow-Control (LFC) Wing Panel Structural Design and Development (WSSD); design, manufacturing, and testing activities. An in-depth preliminary design of the baseline 1993 LFC wing was accomplished. A surface panel using the Lockheed graphite/epoxy integrated LFC wing box structural concept was designed. The concept was shown by analysis to be structurally efficient and cost effective. Critical details of the surface and surface joint was demonstrated by fabricating and testing complex, concept selection specimens. The Lockheed-Georgia Company accomplishments, Development of LFC Wind Surface Composite Structures (WSCS), are documented. Tests were conducted on two CV2 panels to verify the static tension and fatigue strength of LFC wing surface chordwise joints.

Lineberger, L. B.↗
NASA NTRS2020

Thermal Architecture of A Conceptual Mars Sample Return Lander during Cruise and on Mars

A Pre-Project team is currently studying a conceptual Mars Sample Return (MSR) architecture that would return samples collected by Mars 2020 to Earth. The basic architecture comprises of acquisition of these samples using a sample retrieval lander (SRL), which also would also house the Mars Ascent Vehicle (MAV) and Sample Fetch Rover (SFR). The MAV would put the orbiting sample container (OS) in a Martian orbit, which would then rendezvous with an Earth return orbiter (ERO) and be sent to Earth. This paper focuses on the SRL portion of the potential MSR campaign. The thermal architecture of this mission during cruise to Mars presents several challenges that pertain to the thermal control of the spacecraft and the lander/MAV/rover throughout cruise under varying thermal environments & operating conditions. Additionally, the control of these systems within their allowable operating temperature limits on the Martian surface is very challenging because of the large fluctuations in the environment, operating conditions and limited electrical power and energy availability. This paper will describe the thermal architecture for a potential SRL mission, the key thermal requirements and interfaces.It should be noted that the decision to implement MSR will not be finalized until NASA’s completion of the National Environmental Policy Act (NEPA) process. This document is being made available for information purposes only.

Nicholas, Austin↗
NASA NTRS1986

Simulation studies for surfaces and materials strength

During this reporting period three investigations were carried out. The first area of research concerned the analysis of the structure-energy relationship in small clusters. This study is very closely related to the improvement of the potential energy functions which are suitable and simple enough to be used in atomistic simulation studies. Parameters obtained from ab initio calculations for dimers and trimers of Al were used to estimate energetics and global minimum energy structures of clusters continuing up to 15 Al atoms. The second research topic addressed modeling of the collision process for atoms impinging on surfaces. In this simulation study qualitative aspects of the O atom collision with a graphite surface were analyzed. Four different O/graphite systems were considered and the aftermath of the impact was analyzed. The final area of investigation was related to the simulation of thin amorphous Si films on crystalline Si substrates. Parameters obtained in an earlier study were used to model an exposed amorphous Si surface and an a-Si/c-Si interface. Structural details for various film thicknesses were investigated at an atomistic level.

Halicioglu, T.↗
DOE OSTI2024

Multinonmetal-Doped V 2 O 5 Nanocomposites for Lithium-Ion Battery Cathodes

Lithium-ion batteries (LIBs) are critical for portable electronics and electric vehicles, demanding higher energy density to meet increasing energy storage needs. Current commercial cathode materials, such as LiFePO 4 and LiCoO 2 , are limited by a single electron transfer, restricting their energy density. Vanadium pentoxide (V 2 O 5 ) emerges as a promising high-capacity cathode due to its high theoretical capacity of 443 mA h g –1 with three Li storage capacities, significantly surpassing conventional materials. However, the practical application of V 2 O 5 is hindered by a large structural evolution and rapid capacity fading during full lithium intercalation. Here, this study introduces a multinonmetal doping (MNM) strategy to enhance V 2 O 5 cathodes by incorporating all-nonmetal dopants (B, P, and Si) and graphene (G). MNM-V 2 O 5 -G exhibits increased surface oxygen defects, improving charge transfer kinetics and thus enhancing the rate performance and cycling stability. Our results provide valuable insights into the role of surface oxygen defects in stabilizing V 2 O 5 with element doping. This research highlights the potential of multinonmetal doping to improve LIB cathode materials, offering a promising pathway for design of high-energy-density V 2 O 5 cathodes and advancing the development of next-generation energy storage solutions.

25 ENERGY STORAGE↗
DOE OSTI2024

Simple and Accurate One-Body Energy and Dipole Moment Surfaces for Water and Beyond

Water is often the testing ground for new, advanced force fields. While advanced functional forms for intermolecular interactions have been integral to the development of accurate water models, less attention has been paid to a transferable model for intramolecular valence terms. In this work, we present a one-body energy and dipole moment surface model, named 1B-UCB, that is simple yet accurate and can be feasibly adapted for both standard and advanced potentials. 1B-UCB for water is comparable in accuracy to those with much more complex functional forms, despite having drastically fewer parameters. The parametrization protocol has been implemented as part of the Q-Force automated workflow and requires only a quantum mechanical Hessian calculation as reference data, hence allowing it to be easily extended to a variety of molecular systems beyond water, which we demonstrate on a selection of small molecules with different symmetries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Surface Roughness Effects from Additive Manufacturing in High Efficiency Gas Turbine Combustion Systems

In the past, clean combustion systems were characterized by high system development costs due to growing complexity and escalating manufacturing costs from conventional manufacturing processes. As a result, high efficiency concepts are difficult to design and more difficult to be cost-effectively manufactured. In recent years, with the introduction of additive manufacturing (AM) technologies, the rapid prototyping and mass production processes of clean combustion systems are promising to be significantly simplified with significant reduction in terms of engine manufacturing cost and engine energy cost. Compared with conventional manufacturing built parts, the AM process enabled a simpler design to be adopted for the nozzle, reducing the number of required braze and weld joints from twenty-five to just five. The resulting nozzle was 25% lighter and five times more durable and contributed to a 15% reduction in fuel burn in comparison with the previous model produced. Applying these improvements to a fleet of 5,000 turbofan engines at 150 kN thrust would result in fuel cost savings of $6B annually (at $5/gallon Jet-A fuel price, 700 gallon/hour fuel consumption rate, and 2,300 operational hours per year),and reduce CO2 emissions by more than 25 million tons per year. These advances support core Department of Energy (DOE)missions in energy efficiency, improving productivity, and environmental sustainability. Maximizing the benefit of these new capabilities will require high prediction capability of high speed turbulent flow with wall modeled Large Eddy Simulation (LES). GE Aviation maintains that advanced simulation technology and supercomputing is required in order to provide the appropriate boundary conditions to realize the maximum potential of AM and Ceramic Matrix Composite to reduce cooling flow, a first order penalty on the Brayton cycle. The algorithm developed using the ANSYS/Fluent software would provide the foundation for entirely new avenues of research and development with potential multi-billion dollar impact to the US economy, and significant reduction in carbon based emissions across the aerospace and power generation industries. The formulation of this iWLES (integral wall model for LES) is generic and allows to capture the changes in flow dynamics that have a significant impact on the wall bounded flow characteristics, such as swirler effective area, bulk swirl number, local pressure distribution, exit velocity profile, and turbulence kinetic energy profile. A periodic channel flow with rough flat plate is simulated using LES (Wall-Adapting Local Eddy-viscosity) model to verify the implementation of iWLES in the Fluent User Defined Function (UDF). As the flow fields are highly sensitive due to surface roughness of the wall bounded flows in the combustion systems, there is significant potential to conduct further LES studies focusing on the turbulence boundary layer interaction. Accurately capturing near wall physics will elucidate the impact of rough surfaces on combustor flow and aero-thermal interactions.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

Stabilization of magnetic bubbles in [Ni/Co]n multilayers on an oxygen-reconstructed Nb(110) surface via an ultra-thin Cu interlayer

Magnetic thin films hosting topological spin textures, such as magnetic skyrmions, hold high potential for breakthroughs in the field of spintronics, due to good scalability and energy efficiency. Novel computational architectures such as memory-in-logic devices rely on material platforms able to host those topological spin textures. Furthermore, recently proposed designs of novel quantum information technologies are based on heterostructures where topological spin textures are in direct proximity to a superconducting layer. Here, we demonstrate the stabilization of out-of-plane magnetic bubbles in highly ordered [Ni/Co]n multilayers on a Nb(110) single crystal. This is achieved without the need for the removal of the well-known Nb(110)-oxide surface reconstruction, due to the introduction of an ultra-thin Cu interlayer in between the Nb substrate and the magnetic multilayer. The Cu interlayer generates a well-ordered hexagonal surface, which is key for the epitaxial growth of the [Ni/Co]n multilayers hosting the desired out-of-plane anisotropy. The magnetic ground state of the prepared material stacks is directly imaged via spin-polarized low-energy electron microscopy, revealing the presence of magnetic bubble domains with lateral sizes as small as 450 nm.

Dibajeh, Ahmad↗
DOE OSTI2020

Strongly Surface State Carrier‐Dependent Spin–Orbit Torque in Magnetic Topological Insulators

Abstract The topological surface states (TSS) in topological insulators (TIs) can exert strong spin–orbit torque (SOT) on adjacent magnetization, offering great potential in implementing energy‐efficient magnetic memory devices. However, there are large discrepancies among the reported spin Hall angle values in TIs, and its temperature dependence still remains elusive. Here, the spin Hall angle in a modulation‐doped Cr‐Bi x Sb 2− x Te 3 (Cr‐BST) film is quantitatively determined via both transport and optic approaches, where consistent results are obtained. A large spin Hall angle of ≈90 in the modulation‐doped Cr‐BST film is demonstrated at 2.5 K, and the spin Hall angle drastically decreases to 0.3–0.5 as the temperature increases. Moreover, by tuning the top TSS carrier concentration, a competition between the top and bottom TSS in contributing to SOT is observed. The above phenomena can account for the large discrepancies among the previously reported spin Hall angle values and reveal the unique role of TSS in generating SOT.

Che, Xiaoyu↗
DOE OSTI2022

Nanoconfinement matters in humidified CO 2 interaction with metal silicates

With enigmatic observations of enhanced reactivity of wet CO 2 -rich fluids with metal silicates, the mechanistic understanding of molecular processes governing carbonation proves critical in designing secure geological carbon sequestration and economical carbonated concrete technologies. Here, we use the first principle and classical molecular simulations to probe the impact of nanoconfinement on physicochemical processes at the rock–water–CO 2 interface. We choose nanoporous calcium–silicate–hydrate (C–S–H) and forsterite (Mg 2 SiO 4 ) as model metal silicate surfaces that are of significance in cement chemistry and geochemistry communities, respectively. We show that while a nanometer-thick interfacial water film persists at unsaturated conditions consistent with in situ infrared spectroscopy, the phase behavior of the water–CO 2 mixture changes from its bulk counterpart depending on the surface chemistry and nanoconfinement. We also observe enhanced solubility at the interface of water and CO 2 phases, which could amplify the CO 2 speciation rate. Additionally, through free energy calculations, we show that CO 2 could be found in a metastable state near the C–S–H surface, which can potentially react with surface water and hydroxyl groups to form carbonic acid and bicarbonate. These findings support the explicit consideration of nanoconfinement effects in reactive and non-reactive pore-scale processes.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Revealing Three-Dimensional Morphology in Nanoporous Gold Using Three-Dimensional X-Ray Fresnel Coherent Diffractive Imaging Tomography

Nanoporous metals fabricated by dealloying have a unique bi-continuous, sponge-like porous structure with ultra-high surface area. The unique properties of these materials, especially nanoporous gold, have numerous potential applications in sensors and actuators and in energy-related applications such as catalytic materials, super-capacitors, and battery supports. The degree of porosity and size of the metal ligaments are critical parameters that determine many properties and thus govern the functionalities of nanoporous metals in many applications including energy storage and conversion. Additionally, we used Fresnel coherent diffractive imaging combined with tomographic reconstruction to quantify the nanoscale three-dimensional spatial distribution and homogeneity of the porosity and ligament size within a bulk sample of nanoporous gold. The average porosity and its standard deviation along the axial direction through the sample were determined, as well as the characteristic feature size and its standard deviation. The result shows that free corrosion is an effective way to create homogeneous nanoporous metals with sample sizes on the order of 1 µm.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Role of Pr-Vacancies and O-Interstitials on the Activity and Stability of (Pr 1−x Ln x ) 2 NiO 4 (Ln = La, Nd, Pm, Sm, Gd, Tb, Dy, and Ho) towards Oxygen Reduction Reactions: A DFT Study

Praseodymium nickelate, Pr 2 NiO 4 (PNO), is a promising electrode to promote oxygen reduction reaction (ORR) in a solid oxide fuel cell, but it exhibits phase transformation during electrochemical operation. The origin of the simultaneous phase transformation and high electrochemical performance remains obscure. We carried out a systematic density functional theory study to elucidate the mechanism for this conjugated phenomenon. Charge, electronic structure, and normal-mode analysis suggest the presence of peroxide. Our study shows that the formation of peroxide (O 2 2– ) is attributed to both oxygen interstitials and Pr vacancies. The peroxide species limits the oxygen ion migration due to the additional energy required to break its O–O bond, which leads to a decrease in ORR activity. Subsequently, we investigate the diffusion paths of Pr-ions while comparing them with those of other Ln 3+ ions (La, Nd, Pm, Sm, Gd, Tb, Dy, and Ho) in PNO. The formation energies for various Ln 3+ cation occupancies are calculated, as well as segregation energies in CeO 2 (111) surfaces. Lastly, criteria for effective Ln 3+ dopants are developed. La, Nd, and Pm are proposed as potential substituents in PNO to obtain a stable structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗