Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “observable behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Propagation of quasifracture in viscoelastic media under low-cycle repeated stressing

The propagation of a craze as quasifracture under repeated cyclic stressing in polymeric systems has been under intensive investigation recently. Based upon a time-dependent crazing theory, the governing differential equation describing the propagation of a single craze as quasifracture in an infinite viscoelastic plate has been solved for sinusoidal stresses. Numerical methods have been employed to obtain the normalized craze length as a function of time. The computed results indicate that the length of a quasifracture may decelerate and decrease indicating that its velocity can reverse. This behavior may be consistent with the observed and much discussed craze healing and the enclosure model in fatigue and fracture of solids.

Liu, X. P.↗

Non-equilibrium phase distribution in an Al-SiC composite

The phase distribution in an Al-SiC composite has been investigated using high resolution analytical electron microscopy. Particular attention was focused on Al-SiC interfaces, matrix boundaries and impurity phases which would impede the easy glide of dislocations. Small crystallites of MgO were distributed singly and in clusters along Al-SiC interfaces in all specimens. Interfacial segregation and precipitation involving alloy species apparently affected precipitation in the matrix, where the distribution of phases was found to be very heterogeneous. Matrix phases also included unusually large constituent particles and dispersoids, a consequence of the composite processing methods. The relationship between the observed microstructure and the composite mechanical behavior reported by others is discussed. The heterogeneous distribution of matrix phases is expected to result in a wide variaiton in local yield stress and local work-hardening rate within the composite.

Nutt, S. R.↗

The tensile and fatigue deformation structures in a single crystal Ni-base superalloy

Dislocation structures produced in Rene N4 crystals of various orientations deformed in tension and low cycle fatigue (LCF) at 760 and 980 degrees C were examined in order to elucidate the observed differences in stress-strain behavior. Specimens tensile tested at 760 degrees C displayed significant crystallographic orientation dependences in mechanical response but comparable inhomogeneous dislocation structures. LCF specimens of various orientations had comparable cyclic stress-strain curves and generally similar somewhat more homogeneous dislocation structures. Tensile specimens at the higher temperature had comparable mechanical response and corresponding similar quite homogeneous dislocation structures with gamma' faulting; and LCF specimens had orientation-dependent mechanical response but comparable homogeneous loose dislocation networks.

Gabb, T. P.↗

The theory of the earth's orientation, with some new results for nutation

The rotation of the earth is variable at a number of time scales, from a few days to thousands of years and longer. Variations occur in the rotation rate, in the geographical position of the rotation axis (referred to as polar motion), and in the position of the axis relative to inertial space (referred to as nutation and precession). The interpretations of the various observations have implications for the dynamical behavior and structure of the earth's deep interior, and for various aspects of meteorology and oceanography. These are reviewed below. A model of the diurnal resonance in nutation for a nonhydrostatically pre-stressed earth is also presented.

Wahr, John M.↗

Vortex shedding experiment with flat and curved bluff plates in water

Vortex shedding experiments were conducted in a water flow facility in order to simulate the strong discrete 4000-Hz vibration detected in the Space Shuttle Main Engine (SSME) which is thought to be associated with the SSME LOX inlet tee splitter vanes on the Main Injector. For the case of a flat vane with a blunt trailing edge excited by flow induced vortex shedding, lock-in with the first bending mode of the plate was observed. A curved vane displayed similar behavior, with the lock-in being a more discrete higher amplitude response. Aluminum vanes were employed to decouple the first vane bending mode from the vortex shedding mode. The application of an asymmetric 30-deg trailing edge bevel to both the flat and curved vanes was found to greatly reduce the strength of the shed vortices.

Reed, D.↗

Experimental investigation of the hydrodynamic forces on the shroud of a centrifugal pump impeller

Fluid-induced forces acting on a rotating impeller are known to cause rotor-dynamic problems in turbomachines. The forces generated by leakage flow along the front shroud surface of a centrifugal turbomachine impeller play an important role among these fluid-induced forces. The present research was aimed to gain a better understanding of these shroud forces. An experimental apparatus was designed and constructed to simulate the impeller shroud leakage flow. Hydrodynamic forces and steady and unsteady pressure distributions on the rotating shroud were measured as functions of eccentricity, width of shroud clearance, face seal clearance and shaft rotating speed. The forces measured from the dynamometer and manometers agreed well. The hydrodynamic force matrices were found skew-symmetric and statically unstable. This is qualitatively similar to the result of previous hydrodynamic volute force measurements. Nondimensionalized normal and tangential forces decrease slightly as Reynolds number increases. As the width of the shroud clearance decreases and/or the eccentricity increases, the hydrodynamic forces increase nonlinearly. There was some evidence found that increased front seal clearance could reduce the radial shroud forces and the relative magnitude of the destabilizing tangential force. Subharmonic pressure fluctuations were also observed which may adversely affect the behavior of the rotor system.

Zhuang, Fei↗

Infrared reflectance measurements of the insulator-metal transition in solid hydrogen

Reflectance measurements on solid hydrogen to 177 GPa (1.77 Mbar) have been performed from near-infrared to ultraviolet wavelengths (0.5 to 3 eV). Above 150 GPa characteristic free-electron behavior in the infrared region is observed to increase sharply with increasing pressure. Analysis of volume dependence of the plasma frequency obtained from Drude-model fits to the spectra indicates that the pressure of the insulator-metal transition is 149 (+ or - 10) GPa at 295 K. The measurements are consistent with metallization by closure of an indirect gap in the molecular solid.

Mao, H. K.↗

Pressure drop of He II flow through a porous media

The paper reports on measurements of He II pressure drop across two porous SiO2 ceramic filter materials. These materials vary only in porosity, having values of 0.94 and 0.96. The average fiber diameter in both cases is approximately 5 microns. The experiment consists of a glass tube containing a piece of this sponge in one end. The tube is rapidly displaced downward in a bath of helium and the liquid levels are allowed to equilibrate over time producing variable velocities up to 10 cm/sec. The results are compared with those previously obtained using fine mesh screens. Good qualitative agreement is observed for turbulent flow; however, the behavior in the laminar flow regime is not fully understood.

Maddocks, J. R.↗

Sir William Herschel's notebooks - Abstracts of solar observations

An introduction to the background of Sir William Herschel's notebooks and the historical context within which his observations were made are provided. The observations have relevance in reconstructing solar behavior, as discussed in a separate analysis paper by Hoyt and Schatten (1992), and in understanding active features on the sun such as faculae. The text of Herschel's notebooks with modern terms used throughout forms the body of this paper. The complete text has not previously been published and is not easily accessible to scholars. Herschel used different words for solar features than are used today, and thus, for clarity, his terminology is changed on two occasions. A glossary explains the terminology changed. In the text of the notebooks, several contemporaries are mentioned; a brief description of Herschel's colleagues is provided.

Hoyt, Douglas V.↗

'Wave' analysis of Venus ionospheric flux ropes

The behavior of the general field fluctuations observed by the Pioneer Venus Orbiter magnetometer in the Venusian ionosphere is approached via the application of wave-analysis techniques to their compressional amplitude, ellipticity, and polarization. The most marked change in these properties occurs within about 15 deg of the terminator; ellipticity and compressional power plummet, implying that flux ropes either drastically change in character there or are confined to the dayside hemisphere, within about 75 percent of the subsolar point. Attention is given to a heuristic model which attempts to unify dayside flux-rope and 'terminator wave' interpretations.

Luhmann, J. G.↗

High power GaInAs lasers with distributed Bragg reflectors

Single-mode strained-layer lasers have been fabricated which use buried second-order gratings for distributed Bragg reflectors. The lasers contain a strained GaInAs quantum well in the active region and operate in an edge emitting fashion with CW powers in excess of 110 mW. Single longitudinal and transverse mode operation is maintained at about 971.9 nm up to 42 mW. Total power conversion efficiencies as high as 28 percent have been observed. The longitudinal and transverse mode behavior is stable under 90 percent amplitude modulation with 50 percent duty cycle pulses at 10 kHz and 10 MHz. Preliminary life-test data at 40 C also indicate room temperature lifetimes in excess of 45,000 hours.

O'Brien, S.↗

Observations on infiltration of silicon carbide compacts with an aluminium alloy

The melt infiltration of ceramic particulates permits an opportunity to observe such fundamental materials phenomena as nucleation, dynamic wetting and growth in constrained environments. Experimental observations are presented on the infiltration behavior and matrix microstructures that form when porous compacts of platelet-shaped single crystals of alpha- (hexagonal) silicon carbide are infiltrated with a liquid 2014 Al alloy. The infiltration process involved counter gravity infiltration of suitably tamped and preheated compacts of silicon carbide platelets under an external pressure in a special pressure chamber for a set period, then by solidification of the infiltrant metal in the interstices of the bed at atmospheric pressure.

Asthana, R.↗

Probing the statistics of primordial fluctuations and their evolution

The statistical distribution of fluctuations on various scales is analyzed in terms of the counts in cells of smoothed density fields, using volume-limited samples of galaxy redshift catalogs. It is shown that the distribution on large scales, with volume average of the two-point correlation function of the smoothed field less than about 0.05, is consistent with Gaussian. Statistics are shown to agree remarkably well with the negative binomial distribution, which has hierarchial correlations and a Gaussian behavior at large scales. If these observed properties correspond to the matter distribution, they suggest that our universe started with Gaussian fluctuations and evolved keeping hierarchial form.

Gaztanaga, Enrique↗

A vacuum (10 exp -9 torr) friction apparatus for determining friction and endurance life of MoS(x) films

An ultrahigh-vacuum tribometer for use in a ball-on-disk configuration was specially designed for measuring the friction and endurance life of magnetron-sputtered solid lubricating MoS(x) films deposited on sputter-cleaned 400 C stainless-steel disks, when slid against a 6-mm-diameter 440 C stainless-steel ball. The results of tests showed that the tribometer performs satisfactorily in unidirectional rotation in vacuum at a pressure of 10 exp -7 Pa, 10 exp -9 torr. Similarities are observed in the life cycle friction behavior and the coefficient of friction as a function of the number of disk revolutions, for MoS(x) films at average Hertzian contact from 0.33 to 0.69 GPa.

Miyoshi, Kazuhisa↗

Balloon measurements of stratospheric HCl and HF by far infrared emission spectroscopy

We have analyzed atmospheric thermal emission spectra obtained with the balloon-borne FIRS-2 far infrared Fourier transform spectrometer during balloon flights from Palestine, Texas on May 12-13, 1988 and from Fort Sumner, New Mexico on September 26-27, 1989 and on July 4-5, 1990. Seven and two pure rotational transition lines in 100-205 cm(exp -1) range are analyzed for deriving vertical profiles of stratospheric HCl and HF, respectively. We obtain both the daytime and nighttime average vertical profiles from 15 to 50 km. We compare these profiles with the ones obtained in June, 1983 with the first version of FIRS spectrometer during the Balloon Intercomparison Campaign (BIC-2). BIC-2 results were revised to be consistent with the present analysis which uses the latest spectral parameters. According to our comparison results no increase is recognized for HCl but about 3 percent per year increase for HF from 1983 to 1990, assuming a linear trend. These annual increase rates are smaller than those reported by other groups. Recently Rinsland et al. (1991) and Wallace and Livingston (1991) reported long term behavior of total HCl and HF observed on Kit Peak between 1977 and 1990. As Kit Peak is located near both balloon launching sites, Palestine and Fort Sumner, we think our results are favorably comparable with theirs. Comparison results with ours and ground-based measurements will be presented and discussed.

Shibasaki, Kazuo↗

Report on twisted nematic and supertwisted nematic device characterization program

In this study we measured the optical characteristics of normally white twisted nematic (NWTN) and super twisted nematic (STN ) cells. Though no dynamic computer model was available, the static observations were compared with computer simulated behavior. The measurements were taken as a function of both viewing angle and applied voltage and included in the static case not only luminance but also contrast ratio and chromaticity . We employed the computer model Twist Cell Optics, developed at Kent State in conjunction with this study, and whose optical modeling foundation, Iike the ViDEOS program, is the 4 x 4 matrix method of Berreman. In order to resolve discrepancies between the experimental and modeled data the optical parameters of the individual cell components, where not known, were determined using refractometry, profilometry, and various forms of ellipsometry. The resulting agreement between experiment and model is quite good due primarily to a better understanding of the structure and optics of dichroic sheet polarizers. A description of the model and test cells employed are given in section 2. Section 3 contains the experimental data gathered and section 4 gives examples of the fit between model and experiment. Also included with this report are a pair of papers which resulted from the research and which detail the polarizer properties and some of the cell characterization methods.

Source record↗

Thermal barrier coatings for aircraft engines: History and directions

Thin thermal barrier coatings for protecting aircraft turbine section airfoils are examined in this paper. The discussion focuses on those advances that led first to their use for component life extension, and more recently as an integral part of airfoil design. Development has been driven by laboratory rig and furnace testing corroborated by engine testing and engine field experience. The technology has also been supported by performance modeling to demonstrate benefits and life modeling for mission analysis. Factors which have led to the selection of the current state-of-the-art plasma sprayed and physical vapor deposited zirconia-yttria/MCrAlX TBC's are emphasized, as are observations fundamentally related to the their behavior. Current directions in research into thermal barrier coatings and recent progress at NASA are also noted.

Miller, Robert A.↗

Geotail Measurements Compared with the Motions of High-Latitude Auroral Boundaries during Two Substorms

Geotail plasma and field measurements at -95 R(sub E) are compared with extensive ground-based, near-Earth, and geosynchronous measurements to study relationships between auroral activity and magnetotail dynamics during the expansion phases of two substorms. The studied intervals are representative of intermittent, moderate activity. The behavior of the aurora and the observed effects at Geotail for both events are harmonized by the concept of the activation of near-Earth X lines (NEXL) after substorm onsets, with subsequent discharges of one or more plasmoids down the magnetotail. The plasmoids must be viewed as three-dimensional structures which are spatially limited in the dawn-dusk direction. Also, reconnection at the NEXL must proceed at variable rates on closed magnetic field lines for significant times before beginning to reconnect lobe flux. This implies that the plasma sheet in the near-Earth magnetotail is relatively thick in comparison with an embedded current sheet and that both the NEXL and distant X line can be active simultaneously. Until reconnection at the NEXL engages lobe flux, the distant X line maintains control of the poleward auroral boundary. If the NEXL remains active after reaching the lobe, the auroral boundary can move poleward explosively. The dynamics of high-latitude aurora in the midnight region thus provides a means for monitoring these processes and indicating when significant lobe flux reconnects at the NEXL.

Maynard, N. C.↗