Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Interdiffusion and Formation of Intermetallic Compounds in High-Temperature Power Electronics Substrate Joints Fabricated by Transient Liquid Phase Bonding

Power electronics packages typically comprise a dielectric substrate bonded to a metal layer and attached to heat sinks using a low-thermal-conductivity solder. These multiple layers increase the effective thermal resistance of the package and are responsible for package failures under cyclic thermal loads. Bonding the aluminum nitride dielectric layer (AlN) directly to a low coefficient of thermal expansion (CTE) aluminum silicon carbide (AlSiC) cold plate using copper-aluminum (Cu-Al) transient liquid phase (TLP) bonding has been shown to improve the mechanical reliability of the power electronic packages while making the package more compact by bringing the cooling solutions closer to the devices. This study aims to characterize the Cu-Al bonds formed during the TLP bonding of AlSiC with three different power electronics substrates: pure aluminum nitride (AlN), aluminum (DBA), and copper (DBC). The material compositions and microstructures of the bonds were analyzed using scanning electron microscopy (SEM), x-ray spectroscopy (EDS), confocal scanning acoustic microscopy (C-SAM), and x-ray diffraction (XRD). ..alpha..-Al solid compound was identified as the dominant phase in AlN-AlSiC and Al-AlSiC, with a notable presence of SiC particles. In contrast, three intermetallic phases - ..theta..-CuAl2, ..eta..-CuAl, and ..gamma..'- Cu9Al4 - were observed in the Cu-AlSiC bond. A computational solid-state diffusion model was developed to predict the intermetallic compounds (IMCs) formed during Cu-Al TLP bonding in each system, which supported the observation that an initial Cu volume fraction of 20 % in the material layers produced a final bond composition of >95 % Al with minimal IMC growth. However, increased Cu concentrations produced higher concentration gradients, leading to increased growth of IMCs, Kirkendall voids, and interstitial cracks.

DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Diversifying Composition Leads to Hierarchical Composites with Design Flexibility and Structural Fidelity

Although significant progress has been made in the self-assembly of nanostructures, present successes heavily rely on precision in building block design, composition, and pair interactions. These requirements fundamentally limit our ability to synthesize macroscopic materials where the likelihood of impurity inclusion escalates and, more importantly, to access molecular-to-nanoscopic-to-microscopic-to-macroscopic hierarchies, since the types and compositions of building blocks vary at each stage. Inspired by biological blends and high-entropy alloys, we hypothesize that diversifying the blend’s composition can overcome these limitations. Increasing the number of components increases mixing entropy, leading to the dispersion of different components and, as a result, enhances interphase miscibility, weakens the dependence on specific pair interactions, and enables long-range cooperativity. This hypothesis is validated in complex blends containing small molecules, block copolymer-based supramolecules, and nanoparticles/colloidal particles. Hierarchically structured composites can be obtained with formulation flexibility in the filler selection and blend composition. It is worth noting that, by adding small molecules, we can solve the size constraint that plagues traditional block copolymer/nanoparticle blends. Detailed characterization and simulation further confirm that each component is distributed to locally mediate unfavorable interactions, cooperatively mitigate composition fluctuations, and retain structural fidelity. Furthermore, the blends have sufficient mobility to access tunable microstructures without compromising the order of the nanostructure. Besides establishing a kinetically viable pathway to release current constraints in the composite design and to navigate uncertainties during structure formation over multiple length scales, the present study demonstrates that entropy-driven behaviors can be realized in systems beyond high-entropy alloys despite inherent differences between metal alloys and organic/inorganic hybrids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Synthesis and Flash Sintering of (Hf1-xZrx)B2 Solid Solution Fine Powders

Fine powders of (Hf1-xZrx)B2 solid solution were synthesized by two methods. In the first one, solution-based processing of HfCl4, ZrCl4, sucrose and H3BO3 was carried out followed by heat treatment (e.g., at 1500 °C for 1 h) in Argon to achieve the carbothermal reduction (CTR) reaction to form the boride solid solution. In the second one, called boron hydride reduction (BHR) method, HfCl4, ZrCl4 and NaBH4 were directly mixed in a glove box followed by heat treatment in Argon at elevated temperatures from 700 to 1500 °C. In addition, the powders synthesized via both methods were flash sintered without sample preheating in a homemade setup. The synthesized powders as well as the flash sintered bulk ceramics were characterized using different techniques including XRD, SEM, EDS, TEM, TGA-DSC, and Vickers hardness test to reveal the inter-relationships between starting materials composition, processing conditions, and the resulting materials microstructure and physical/chemical properties.

Belisario, Jose↗
DOE OSTI2024

Characterization of Fuel Cladding Chemical Interaction on a High Burnup U-10Zr Metallic Fuel via Electron Energy Loss Spectroscopy Enhanced by Machine Learning

Fuel cladding chemical interaction (FCCI) is one of the main performance limiting factors for metallic nuclear fuels. The interaction destabilizes the martensitic microstructure and deteriorates mechanical properties of HT-9 cladding. The detection of low atomic number elements (Z<10) and overlapping of elemental peaks can be problematic in interpreting energy dispersive X-ray spectroscopy (EDS) data. Electron energy loss spectroscopy (EELS) provides precise elemental edge energy values and can detect elements with a low atomic number. This work utilizes EELS to study the distribution of lanthanides and light elements at the interaction region. The sample was prepared from the FCCI region of a U-10Zr (wt.%) solid fuel with HT-9 cladding, irradiated to a burnup of 13.2 at.%. Processing the EELS data included three major steps: 1) enhance the signal to noise ratio by denoising the spectrum with principal component analysis (PCA) method, removing background and performing deconvolution; 2) identify chemical elements with core energy loss edges; 3) confirm different phases using a popular machine learning method, K-means. This work presents qualitative assessment of lanthanides and light elements like carbon (C) and oxygen (O) enhanced by the application of machine learning algorithms. By comparing with EDS elemental maps, EELS provides higher resolution chemical maps, reveals the distribution of carbon at the interaction region supporting the formation of zirconium carbide, a rind-like microstructure feature that was proposed to mitigate the chemical interaction. Furthermore, the plasmon peak map was also found to indicate an energy shift associated with the formation of phases/compounds. K-means clustering method was used on the processed electron energy loss (EEL) spectrum to automatically reveal different phases. The resulting clustered maps from K-means clustering align well with elemental maps confirming certain phases, especially Fe-Ce and Zr-C, in the FCCI region.

EELS↗
DOE OSTI2026

4D-STEM Coupled with Unsupervised Machine Learning to Reveal at Large-Scale the Microstructural Evolution in Li- and Mn-Rich Cathodes

Li- and Mn-rich (LMR) layered oxides are known to exhibit a thin surface reconstruction layer, which grows during electrochemical cycling in a manner that depends on exposed crystallographic facets, cycling conditions, and electrolyte chemistry. Direct characterization of this layer has traditionally relied on high-resolution electron microscopy, which is inherently limited to small fields of view. Here, we employ four-dimensional scanning transmission electron microscopy (4D-STEM) combined with unsupervised machine-learning clustering to quantitatively map phase distributions over large areas and track their evolution in LMR cathodes during electrochemical aging. Our results show that the surface reconstruction layer consists predominantly of a rocksalt phase, whose thickness varies across different facets following activation cycling and becomes substantially thicker and more uniform during calendar aging. In contrast, a spinel-like phase is observed within the particle bulk. Large-area phase mapping and correlative high-resolution imaging reveal that this spinel-like phase preferentially nucleates at bulk crystallographic defects, including boundaries between 60°-rotated layered domains and associated mixed-phase regions, rather than exclusively at the particle surface. Our findings establish a mechanistic distinction between surface-driven rocksalt formation and bulk-defect-mediated spinel nucleation while demonstrating the unique capability of 4D-STEM to provide statistically robust, mesoscale insight into complex phase-evolution processes in LMR cathodes.

4D-STEM↗
DOE OSTI2023

Use of Graph Theory and Neural Networks for Microstructural Classification

Recent advances in materials data analytics have provided new avenues for determining process-structure-property (PSP) linkages in a variety of materials. Machine learning techniques including few-shot learning have increased the efficiency of classifying microscopy images for the purposes of material characterization. Modifications in segmentation also show potential in improving the accuracy of our current pyCHIP classifier. Replacing previous encoders trained on ImageNet with those trained on microscopy images like MicroNet has initially shown better performance at classifying images of irradiated samples. Additionally, different normalization approaches were tested to show no discernable effect on classification. The Louvain method for community detection is analyzed on a set of irradiated samples with different parameters to determine which proved beneficial under what circumstances. We suggest that microscopy experiments be automated in the future using a combination of these techniques to enable high-throughput analyses.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural Passivation of Patterned Al 2 O 3 Back Contacts on CdS/CdTe Solar Cells

Abstract Patterned aluminum oxide (Al 2 O 3 ) back contact on cadmium telluride (CdTe) solar cells can effectively mitigate the loss of the majority carriers while retaining the passivation benefits for minority carriers. This study investigates the impact of the point‐contact geometry on cell performance, where the spacing of the microholes is systematically varied at a constant microhole diameter (≈16 µm). Microhole arrays are created on an evaporated Al 2 O 3 layer (≈30 nm) on CdTe using laser‐beam lithography and selective wet etching processes. Comparative analysis indicates a significant decrease in fill factor (FF) and short‐circuit current ( I SC ) when the contact fraction falls below 30%, likely due to the Al 2 O 3 barrier impeding majority carriers. Above this fraction, FF and I SC are comparable to those of baseline CdTe cells without Al 2 O 3 . Open‐circuit voltage ( V OC ) shows a gradual decrease as Al 2 O 3 coverage is reduced but exhibits a slight increase (<15 mV) when the contact fraction exceeds 30%. Cathodoluminescence (CL) characterization reveals that significantly improved radiative recombination occurs within the CdTe grain bulk with Al 2 O 3 , whereas this effect on grain boundaries is minimal. The findings imply complex local carrier dynamics in the patterned back‐contact region, closely tied to the microstructural properties of CdTe‐based solar cells.

Roy, Etee Kawna↗
DOE OSTI2023

Development and Characterization of a Sustainable Bio-Polymer Concrete with a Low Carbon Footprint

Polymer concrete (PC) has been used to replace cement concrete when harsh service conditions exist. Polymers have a high carbon footprint when considering their life cycle analysis, and with increased climate change concerns and the need to reduce greenhouse gas emission, bio-based polymers could be used as a sustainable alternative binder to produce PC. This paper examines the development and characterization of a novel bio-polymer concrete (BPC) using bio-based polyurethane used as the binder in lieu of cement, modified with benzoic acid and carboxyl-functionalized multi-walled carbon nanotubes (MWCNTs). The mechanical performance, durability, microstructure, and chemical properties of BPC are investigated. Moreover, the effect of the addition of benzoic acid and MWCNTs on the properties of BPC is studied. The new BPC shows relatively low density, appreciable compressive strength between 20–30 MPa, good tensile strength of 4 MPa, and excellent durability resistance against aggressive environments. The new BPC has a low carbon footprint, 50% lower than ordinary Portland cement concrete, and can provide a sustainable concrete alternative in infrastructural applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Helium tribology of Inconel 617 subjected to laser peening for high temperature nuclear reactor applications

Inconel 617 is among the best candidates for utilization in high temperature gas cooled reactor tribo-components. However, the combined effects of sliding contact, along with intermittent idle times and very high temperature material degradation, deteriorates the alloy tribological performance, especially under a helium atmosphere. Laser peening is a surface treatment technique which can enhance the properties at the surface and subsurface by generating deep residual stresses and enhanced microstructure. In this work, we report the tribological behavior of regular laser peened as well as thermally-engineered laser peened Inconel 617 under helium and air atmospheres at 800 °C. In addition to friction and wear studies, the specimens are characterized by different analytical techniques to further understand the mechanisms involved in the peening process and sliding contact. Regardless of the peening process and post-process treatment types, it is observed that laser peening improves the tribological characteristics of Inconel 617. Interestingly, laser peening followed by helium thermal aging shows highly enhanced tribological behavior. This is attributed to the strengthening effect of the laser peening on the surface oxides providing an excellent and lasting protective and lubricating film under helium exposure.

42 ENGINEERING↗
DOE OSTI2024

Characterization of fluidized bed chemical vapor deposition ZrC coatings on PyC/YSZ kernels deposited under differing conditions

In this study, coated fuel particle architectures with ZrC coatings are candidate fuels for advanced power reactors and space nuclear propulsion (SNP) concepts. Owing to its relevance to SNP, the composition, microstructure, and mechanical properties of eight ZrC coatings prepared by fluidized bed chemical vapor deposition were evaluated. Evaluation by SEM and EBSD showed that all grains were columnar. Across the various examined samples, minor axis diameters varied between 0.3 and 1.1 μm, and major axis diameters varied between 0.4 and 2.3 μm. Major and minor diameters increased with thickness particularly at higher deposition temperatures in which the major grain axis (from an ellipse fit to the grain shape) increased by 2.5 μm over the entire coating. Coatings with higher reactive gas flows and Zr/C concentrations closer to 1 were observed to contain nanocrystalline graphite deposits. Reactive gas flow doubling led to increases in coating thickness from around 10–15 μm to around 22–27 μm.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Atom Probe Tomography Investigation of Clustering in Model P 2 O 5 -Doped Borosilicate Glasses for Nuclear Waste Vitrification

Atom probe tomography (APT) has been utilized to investigate the microstructure of two model borosilicate glasses designed to understand the solubility limits of phosphorous pentoxide (P 2 O 5 ). This component is found in certain high-level radioactive defence wastes destined for vitrification, where phase separation can potentially lead to a number of issues relating to the processing of the glass and its long-term chemical and structural stability. The development of suitable focused ion beam (FIB)-preparation routes and APT analysis conditions were initially determined for the model glasses, before examining their detailed microstructures. In a 3.0 mol% P 2 O 5 -doped glass, both visual inspection and sensitive statistical analysis of the APT data show homogeneous microstructures, while raising the content to 4.0 mol% initiates the formation of phosphorus-enriched nanoscale precipitates. This study confirms the expected inhomogeneities and phase separation of these glasses and offers routes to characterizing these at near-atomic scale resolution using APT.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Characterizing Corrosion Mechanisms Of Structural Alloys In Actinide-based Molten Chloride Salt

This is a dataset consisting of 33 GB of .png image files, each featuring a two-dimensional distribution of different element species captured an individual slice of the specimen, and .ang files that capture microstructural information captured from each respective slice using a technique called electron backscatter diffraction. The .ang files can be processed to visualize alloy grains captured in a respective slice.

Copeland, Trishelle M.↗
DOE OSTI2024

3D printed carbon fiber reinforced carbon as an energy efficient alternative to graphite for EFAS tooling

As Electric Field Assisted Sintering (EFAS) gains more industrial acceptance and use, it becomes more important to develop more efficient means to implement this technology. To this aim, 3D printed continuous carbon fiber reinforced carbon (CCC) was manufactured and fabricated into tooling for EFAS systems as an alternative to traditional graphite tooling. The impact of fiber orientation on the thermal and electrical properties of the CCC was characterized. Sample material was sintered in Tokai G535 graphite tooling, under common processing conditions and compared with CCC tooling. There was nearly 50 % energy savings compared to graphite while maintaining equivalent sample density and microstructure plus keeping ram temperatures 39 % cooler. This is due to spatial control of generated heat and thermal diffusivity within the molds, by means of fiber orientation anisotropy. Finite element modeling of the tooling design supported the experimental results as well as displays the effect of optimization of this 3D printed CCC material.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Engineering of Nanoscale Heterogeneous Transition Metal Dichalcogenide–Au Interfaces

Engineering the transition metal dichalcogenide (TMD)–metal interface is critical for the development of two-dimensional semiconductor devices. By directly probing the electronic structures of WS 2 –Au and WSe 2 –Au interfaces with high spatial resolution, we delineate nanoscale heterogeneities in the composite systems that give rise to local Schottky barrier height modulations. Photoelectron spectroscopy reveals large variations (>100 meV) in TMD work function and binding energies for the occupied electronic states. Characterization of the composite systems with electron backscatter diffraction and scanning tunneling microscopy leads us to attribute these heterogeneities to differing crystallite orientations in the Au contact, suggesting an inherent role of the metal microstructure in contact formation. Here we then leverage our understanding to develop straightforward Au processing techniques to form TMD–Au interfaces with reduced heterogeneity. Our findings illustrate the sensitivity of TMDs’ electronic properties to metal contact microstructure and the viability of tuning the interface through contact engineering.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2026

Mechanical behaviour of additively manufactured metals

Additive manufacturing is reshaping the production of engineering components in diverse industries, such as the automotive, aerospace, defense, and biomedical sectors, by offering unprecedented design flexibility. The non-equilibrium processing conditions of additive manufacturing generate materials with unique microstructures and tailored mechanical properties that are often unattainable through conventional routes. This review focuses on recent advances in additively manufactured metals that demonstrate distinctive mechanical behaviors, including strength-ductility synergy, microstresses and gradient plasticity, fracture and fatigue resistance, and high-temperature creep performance. Here, we examine the mechanisms and micromechanical effects arising from the heterogeneous microstructures fabricated by additive manufacturing, to guide the design of a wide range of high-performance structural materials. Furthermore, we discuss critical research needs and emerging opportunities in process control, alloy design, advanced characterization, high-fidelity computational modeling, and machine learning aimed at achieving exceptional mechanical properties in additively manufactured metals.

Additive Manufacturing↗
DOE OSTI2022

Novel fabrication tools for dynamic compression targets with engineered voids using photolithography methods

Mesoscale imperfections, such as pores and voids, can strongly modify the properties and the mechanical response of materials under extreme conditions. Tracking the material response and microstructure evolution during void collapse is crucial for understanding its performance. In particular, imperfections in the ablator materials, such as voids, can limit the efficiency of the fusion reaction and ultimately hinder ignition. To characterize how voids influence the response of materials during dynamic loading and seed hydrodynamic instabilities, we, in this paper, have developed a tailored fabrication procedure for designer targets with voids at specific locations. Our procedure uses SU-8 as a proxy for the ablator materials and hollow silica microspheres as a proxy for voids and pores. By using photolithography to design the targets’ geometry, we demonstrate precise and highly reproducible placement of a single void within the sample, which is key for a detailed understanding of its behavior under shock compression. This fabrication technique will benefit high-repetition rate experiments at x-ray and laser facilities. Insight from shock compression experiments will provide benchmarks for the next generation of microphysics modeling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Separate-Effects Tests for Studying Temperature-Gradient-Driven Cracking in UO 2 Pellets

We report a variety of normal operation and accident scenarios can generate thermal stresses large enough to cause cracking in light-water reactor (LWR) fuel pellets. Cracking of fuel pellets can lead to reduced heat removal, higher centerline temperatures, and localized stress in cladding, all of which impact fuel performance. It is important to experimentally characterize the thermal and mechanical behavior in the pellet before and after cracking to improve cracking models in fuel performance codes. However, in-reactor observation and measurement of cracking is very challenging due to the harsh environment and logistics. Recently, an experimental pellet cracking test stand was developed for separate effects testing of normal operations and accident temperature conditions, using thermal imaging to capture the pellet surface temperature for evaluation of thermal stresses and optical imaging to capture the evolution of cracking in real time. Experiments were performed using depleted uranium dioxide (UO 2 ) pellets, which are useful for collecting data valuable for development and validation of cracking models. A combination of induction and resistance heating was used to create an average temperature gradient of 236°C/cm and 193°C/cm before and after cracking respectively. Characterization of the pellets were done before as well as after cracking. The cracking patterns are somewhat different than those expected in a typical reactor because of the differences in thermal conditions and pellet microstructure. However, if the actual conditions of these experiments are reproduced in computational models, these out-of-pile tests on UO 2 pellets provide relevant data for modeling purposes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Acoustic velocity and permeability of acidized and propped fractures in shale

We report that from geochemical reactions to proppant emplacement, hydraulic fracturing induces various chemomechanical fracture alterations in shale reservoirs. Hydraulic fracturing through the injection of a vast amount and variety of fluids and proppants has substantial impacts on fluid flow and hydrocarbon production. There is a strong need to improve our understanding on how fracture alterations affect flow pathways within the stimulated rock volume and develop monitoring tools. We have conducted time-lapse rock-physics experiments on clay-rich (carbonate-poor) Marcellus shales to characterize the acoustic velocity and permeability responses to fracture acidizing and propping. Acoustic P- and S-wave velocities and fracture permeability were measured before and after laboratory-induced fracture alterations along with microstructural imaging through X-ray computed tomography and scanning electron microscopy. Our experiments indicate that the S-wave velocity is an important geophysical observable, particularly the S-wave polarized perpendicular to fractures because it is sensitive to fracture stiffness. The acidizing and propping of a fracture decrease its elastic stiffness. This effect is stronger for acidizing, so it is possible that proppant monitoring will be masked by chemical alteration except when propping is highly efficient (i.e., most fractures are propped). However, fracture permeability is undermined by the softening of fracture surfaces due to acidizing, while being greatly enhanced by propping. These contrasting effects on fluid flow in combination with similar seismic attributes indicate the importance of experiments to improve existing rock-physics models, which must include changes to the rock frame. Such improvements are necessary for a correct interpretation of seismic velocity monitoring of flow pathways in stimulated shales.

58 GEOSCIENCES↗