Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “desorption”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Electron scattering with ethane adsorbed on rare gas multilayers: Hole transfer, coulomb decay, and ion dissociation

Positive ion desorption following electron impact dissociative ionization of ethane adsorbed on Ar, Kr, and Xe multilayers has been studied as a function of incident electron energy from threshold to 100 eV. Based on the dependence of ion yields on the identity of the rare gas, it is likely that the majority of ethane molecules undergo indirect ionization following hole transfer from the ionized underlying rare gas. Further, this has also been corroborated by density of states calculations showing the energetic alignment of the outer valence states of ethane and the condensed rare gas ionization energies. Due to the near-resonant nature of charge transfer for single-hole states, the ethane molecular ion is excited to different final ionic states on different rare gases, which leads to differences in ion desorption yields and branching ratios. The quantitative yields increase with increasing ionization energy gap between the rare gas and ethane, in the order Ar > Kr >Xe. The large increase in yields from 25 eV onwards for all rare gases is likely due to the formation and decay of two-hole states on neighboring rare gas and ethane molecules due to interatomic and intermolecular Coulomb decay (ICD) and not electron transfer mediated decay (ETMD). The ICD and ETMD pathways become accessible when the incoming electron has sufficient energy to excite the inner valence ns level of the rare gas to a Rydberg state or ionize it. The experimental findings are supported by calculations of thresholds, density of states for the final configurations of these processes, and coupling strengths for hole transfer between ethane and rare gases. The fragment ion branching ratios vary with energy from threshold to about 35 eV, showing the fragmentation pattern changes with the mode of hole transfer and availability of excess energy. Sigma C–C bonds are more likely to break than C–H bonds in the mid-20 eV range, and this effect is most pronounced for Xe, followed by Kr, and then Ar.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evaporation and scattering of neon, methane, and water from a dodecane flat liquid jet

The evaporation and scattering of Ne, CD 4 , and D 2 O from a dodecane flat liquid jet are investigated in a molecular beam apparatus. The experiment yields translational energy distributions as a function of scattering angle by means of a rotatable mass spectrometer. In the evaporation experiments, one observes a Maxwell–Boltzmann distribution with a cos $θ$ angular distribution superimposed on a weak, isotropic background. The scattering experiments show contributions from impulsive scattering and thermal desorption. At select incident angles for the three systems, angular distributions show super-specular scattering for the impulsive scattering channel, an effect attributed to anisotropic momentum transfer to the liquid surface. The impulsive scattering channel is analyzed with a soft-sphere model to explore energy transfer between the scatterer and liquid as a function of deflection angle. In conclusion, compared to Ne scattering, the polyatomic gases exhibit more thermal desorption and, in the impulsive scattering channel, a higher degree of internal excitation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Surface coverage dynamics for reversible dissociative adsorption on finite linear lattices

Dissociative adsorption onto a surface introduces dynamic correlations between neighboring sites not found in non-dissociative absorption. We study surface coverage dynamics where reversible dissociative adsorption of dimers occurs on a finite linear lattice. We derive analytic expressions for the equilibrium surface coverage as a function of the number of reactive sites, N, and the ratio of the adsorption and desorption rates. Using these results, we characterize the finite size effect on the equilibrium surface coverage. For comparable N’s, the finite size effect is significantly larger when N is even than when N is odd. Moreover, as N increases, the size effect decays more slowly in the even case than in the odd case. The finite-size effect becomes significant when adsorption and desorption rates are considerably different. These finite-size effects are related to the number of accessible configurations in a finite system where the odd-even dependence arises from the limited number of accessible configurations in the even case. We confirm our analytical results with kinetic Monte Carlo simulations. We also analyze the surface-diffusion case where adsorbed atoms can hop into neighboring sites. As expected, the odd-even dependence disappears because more configurations are accessible in the even case due to surface diffusion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Surface chlorination of IrO2(110) by HCl

The ability to controllably chlorinate metal-oxide surfaces can provide opportunities for designing selective oxidation catalysts. In the present study, we investigated the surface chlorination of IrO2(110) by HCl using temperature programmed reaction spectroscopy (TPRS), x-ray photoelectron spectroscopy (XPS), and density functional theory (DFT) calculations. We find that exposing IrO2(110) to HCl, followed by heating to 650 K in ultrahigh vacuum, produces nearly equal quantities of on-top and bridging Cl atoms on the surface, Clt and Clbr, where the Clbr atoms replace O-atoms that are removed from the surface by H2O formation. After HCl adsorption at 85 K, only H2O desorbs at low Cl coverages during TPRS, but HCl begins to desorb in increasing yields as the Cl coverage is increased above about 0.5 monolayer (ML). The desorption of Cl2 was not observed under any conditions, in good agreement with the high barrier for this reaction predicted by DFT. A maximum Cl coverage of 1 ML, with nearly equal coverages of Clt and Clbr atoms, could be generated by reacting HCl with IrO2(110) in UHV. Our results suggest that a kinetic competition between recombinative HCl and H2O desorption under the conditions studied limits the saturation Cl coverage to a value less than the 2 ML maximum predicted by thermodynamics. XPS further shows that the partitioning of Cl between the Clt and Clbr states can be altered by subjecting partially chlorinated IrO2(110) to reductive or oxidative treatments, demonstrating that the Cl site population can change dynamically in response to the gas environment. Our results provide insights for understanding the chlorination of IrO2(110) by HCl and can enable future experimental studies to determine how Cl-modification alters the surface chemical reactivity of IrO2(110) and potentially enhances selectivity toward partial oxidation chemistry.

Chemistry↗

The mechanism of hydroxyapatite coatings degradation at high substrate temperatures

Physical vapor deposition methods used for hydroxyapatite (HA) coatings typically require elevated substrate temperatures and post-deposition annealing to induce crystallization. However, such thermal treatments can degrade both the mechanical integrity and bioactivity of the coating, particularly when substrate temperatures exceed 500 °C. The mechanisms underlying these phenomena remain insufficiently understood. In this study, HA thin films were deposited on silicon and Ti6Al4V substrates using pulsed laser deposition and were systematically characterized to elucidate these mechanisms. XPS and SIMS analyses revealed a temperature-dependent loss of OH − and PO 4 3− groups, an increased Ca/P ratio, and the formation of interfacial oxides, all of which contribute to weakened adhesion. To clarify the temperature-dependent decline in bioactivity, protein adsorption behavior was analyzed using a Kramers-type kinetic framework; the fitted desorption kinetics indicate that coatings deposited near ∼500 °C provide the most stable protein attachment, whereas higher temperatures accelerate desorption due to dehydroxylation and carbonate substitution. Together, these findings provide mechanistic insight into the thermal degradation of HA coatings and offer a framework for optimizing deposition parameters to preserve stoichiometry, adhesion, and bioactivity for long-term biomedical applications.

Kylychbekov, Salizhan [Univ. of Oxford (United Kin↗

Molecular dynamics of laser-assisted decomposition of unstable molecules at the surface of carbon nanotubes: case study of CH 2 (NO 2 ) 2 on CNT(4,0)

In this study, photoreactions of the dinitromethane molecule noncovalently adsorbed on the (4, 0) carbon nanotube (CNT) have been investigated by time-dependent, excited-state molecular dynamics, which takes into account simultaneous evolution of electronic excitation and nuclear positions under periodic optical excitations. It is found that desorption of molecular adsorbate from CNT surface can be controlled by UV-vis photoexcitations. In addition, it is shown that the presence of CNT substrate facilitates photodecomposition of the adsorbate molecule, related to optically controlled explosion. This model demonstrates potential of photoinduced charge transfer between the adsorbate and substrate, which can affect efficiency of desorption and decomposition reactions. This process has a potential use as a remote trigger for larger scale detonations, or as a mechanism for ‘cleaning’ CNTs of unwanted functionalisation.

Disrud, Brendon↗

The Influence of Microstructure on Deuterium Retention in Polycrystalline Tungsten

The retention of hydrogen isotopes in the plasma-facing materials of a fusion reactor is dependent on the density of trapping sites in the material. One factor that can influence the trapping defects is the surface state of the material before exposure. Mechanically polished, electropolished, and recrystallized tungsten samples were compared by exposing them to 350 eV D + beams with peak fluences of ~1 × 10 24 D + /m 2 at 500 and 740 K at the Multicharged Ion Research Facility (MIRF). At the exposure temperature of 740 K, no significant retention was detected. For material exposed at 500 K, significant differences in retention were observed, and the order of increasing retention was recrystallized, electropolished, and mechanically polished. Lastly, the other variable besides surface treatment was the time delay between ion exposure and thermal desorption spectroscopy which also may have impacted the retention measurements if there was out-gassing of the D while samples were in storage before thermal desorption spectroscopy (TDS).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Tritium Retention in Hexavalent Chromate-Conversion–Coated Aluminum Alloy

In this work, 6061-T6 aluminum samples were subjected to MIL-DTL-5541F type I, class-3 anodic coatings, where a yellow irradiate finish was achieved. Both chromate-conversion coatings (CCC) and unmodified samples were exposed to DT (PT = 0.51 atm) gas for 24 h at room temperature. Following loading, the samples were subjected to one of two desorption techniques: temperature-programmed desorption, or a surface stripping technique. The results show that chromic-acid anodizing of aluminum dramatically increases the total quantity of tritium retained by the treated surface as compared to unmodified aluminum. X-ray photoelectron spectroscopy and scanning electron microscopy studies of both treated aluminum and unmodified samples indicate that the CCC coating contain significant quantities of hydrated chromium. Using transmission electron microscopy, the surface is shown to have significant cracking and fracturing of the film and leads to a highly grained and porous surface. Such surface defects coupled with the vast quantity of hydration sites are likely reasons for the increased retained tritium inventory observed for CCC samples. Finally, due to the physical and chemical properties of unmodified CCC samples, they are not suitable for use in tritium environments.

36 MATERIALS SCIENCE↗

Performance Restoration of a Tritium-Aged LaNi 4.25 Al 0.75 Sample

Hydride beds containing LaNi 4.25 Al 0.75 (LANA.75) are used to store significant quantities of tritium. These hydride beds have a limited service life due to radiolytic decay of tritium to 3He within the metal matrix. The crystal structure of the hydride is altered by trapped 3 He, which has a very low solubility in the metal. The altered structure induces the formation of a heel of trapped hydrogen isotopes and diminishes the reversible capacity of the hydride. With sufficient tritium exposure, the bed loses the ability to deliver 3He-free tritium, and replacement is needed. Demonstration of a means to regenerate tritium-aged LANA.75 in situ would delay or even eliminate the need to replace lanthanum nickel aluminum (LANA) hydride beds. This paper presents test results obtained during regeneration testing. The efficacy of regeneration testing was evaluated by comparing tritium desorption isotherms collected on the hydride before and after exposure to regeneration conditions. Testing was performed on a bench-scale tritium-aged LANA.75 sample that was previously isotopically exchanged (from tritium to deuterium), passivated, and recovered. Once transferred to a high-temperature test cell, the deuterium heel of the sample was isotopically exchanged with tritium, and a baseline desorption isotherm was collected for comparison purposes. The sample was then heated under vacuum, and comparative isotherms were gathered between regeneration evolutions. Shifts in isotherms show progressive improvements with higher-temperature exposure over the tritium-aged baseline. The heel was significantly reduced, and the reversible capacity of the hydride was essentially restored to near virgin values. For all tested conditions, the plateau pressure remained higher than virgin LANA.75.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

GAS-GRAIN MODELS FOR INTERSTELLAR ANION CHEMISTRY

Long-chain hydrocarbon anions C{sub n}H{sup -} (n = 4, 6, 8) have recently been found to be abundant in a variety of interstellar clouds. In order to explain their large abundances in the denser (prestellar/protostellar) environments, new chemical models are constructed that include gas-grain interactions. Models including accretion of gas-phase species onto dust grains and cosmic-ray-induced desorption of atoms are able to reproduce the observed anion-to-neutral ratios, as well as the absolute abundances of anionic and neutral carbon chains, with a reasonable degree of accuracy. Due to their destructive effects, the depletion of oxygen atoms onto dust results in substantially greater polyyne and anion abundances in high-density gas (with n{sub H{sub 2}}{approx}>10{sup 5} cm{sup -3}). The large abundances of carbon-chain-bearing species observed in the envelopes of protostars such as L1527 can thus be explained without the need for warm carbon-chain chemistry. The C{sub 6}H{sup -} anion-to-neutral ratio is found to be most sensitive to the atomic O and H abundances and the electron density. Therefore, as a core evolves, falling atomic abundances and rising electron densities are found to result in increasing anion-to-neutral ratios. Inclusion of cosmic-ray desorption of atoms in high-density models delays freeze-out, which results in a more temporally stable anion-to-neutral ratio, in better agreement with observations. Our models include reactions between oxygen atoms and carbon-chain anions to produce carbon-chain-oxide species C{sub 6}O, C{sub 7}O, HC{sub 6}O, and HC{sub 7}O, the abundances of which depend on the assumed branching ratios for associative electron detachment.

79 ASTRONOMY AND ASTROPHYSICS↗

Irradiation effect on deuterium behaviour in low-dose HFIR neutron-irradiated tungsten

Tungsten samples were irradiated by neutrons in the High Flux Isotope Reactor, Oak Ridge National Laboratory at reactor coolant temperatures of 50-70°C to low displacement damage of 0.025 and 0.3 dpa under the framework of the US-Japan TITAN program (2007-2013). After cooling down, the HFIR neutron-irradiated tungsten samples were exposed to deuterium plasmas in the Tritium Plasma Experiment, Idaho National Laboratory at 100, 200 and 500 °C twice at the ion fluence of 5×10²⁵ m⁻² to reach a total ion fluence of 1×10²⁶ m⁻² in order to investigate the near surface deuterium retention and saturation via nuclear reaction analysis. Final thermal desorption spectroscopy was performed to elucidate irradiation effect on total deuterium retention. Nuclear reaction analysis results showed that the maximum near surface (<5 µm depth) deuterium concentration increased from 0.5 at % D/W in 0.025 dpa samples to 0.8 at. % D/W in 0.3 dpa samples. The large discrepancy between the total retention via thermal desorption spectroscopy and the near surface retention via nuclear reaction analysis indicated the deuterium was migrated and trapped in bulk (at least 50 µm depth for 0.025 dpa and 35 µm depth for 0.025 dpa) at 500 °C case even in the relatively low ion fluence of 10²⁶ m⁻².

36 MATERIALS SCIENCE↗

Electron beam analysis induces Cl vacancy defects in a NaCl thin film

This work reports on the electron-induced modification of NaCl thin film grown on Ag(110). We show using low energy electron diffraction that electron beam bombardment leads to desorption and formation of Cl vacancy defects on NaCl surface. The topographic structure of these defects is studied using scanning tunneling microscopy (STM) showing the Cl defects as depressions on the NaCl surface. Most of the observed defects are mono-atomic vacancies and are located on flat NaCl terraces. Auger electron spectroscopy confirms the effect of electron exposure on NaCl thin films showing Cl atoms desorption from the surface. Using density functional theory taken into account the van der Waals dispersion interactions, we confirm the observed experimental STM measurements with STM simulation. Furthermore, comparing the adsorption of defect free NaCl and defective NaCl monolayer on Ag(110) surfaces, we found an increase of the adhesion energy and the charge transfer between the NaCl film and the substrate due to the Cl vacancy. In details, the adhesion energy increases between the NaCl film and the metallic Ag substrate from 30.4 meV Å –2 for the NaCl film without Cl vacancy and from 39.5 meV Å –2 for NaCl film with a single Cl vacancy. The charge transfer from the NaCl film to the Ag substrate is enhanced when the vacancy is created, from 0.63e – to 1.25e – .

Materials Science↗

Exploring the Basic Physical Mechanisms of Cathode- and Anode-Initiated High-Voltage Surface Flashover

Surface flashover in vacuum imposes a substantial physical limit on modern, large-scale pulsed power. One of the ramifications is a minimum size requirement for new machines, which in itself becomes a hard barrier to the modernization and improvement of existing infrastructure. Pulsed power topologies require the physical mechanisms of both anode- and cathode-initiated flashover to be considered. Originally, the geometrical implications of field emission at the cathode triple junction (CTJ) motivated the usage of configurations that avoid electrons impinging on the insulating material. This will largely suppress the cathode-initiated flashover, which is best described by the secondary electron avalanche mechanism, gas desorption, and final breakdown in the desorbed gas. It depends on the cascade growth of a conducting plasma along the length of the insulator from the cathode. Mitigating the cathode-initiated flashover typically comes at the cost of a significant field enhancement at the anode triple junction (ATJ). In a typical implementation, the anode field may be three times higher than the cathode field for a given voltage, making the corresponding anode-initiated flashover much more common than otherwise. In the case of pulsed, anode-initiated flashover, experimental evidence suggests that charge is directly extracted from the insulator resulting in the insulator taking on a net positive charge advancing the anode potential. Furthermore, along with accompanying gas desorption from the surface, the potential will then propagate from the anode toward the cathode until the effective length of the gap is sufficiently reduced to support flashover. The underlying physical mechanisms of cathode- and anode-directed flashover are discussed in light of previously gathered experimental data and recent experiments with pulsed, high-gradient, anode-initiated flashover.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Irreversible oxygen poisoning: Modeling the initial water dissociation kinetics on δ-Pu(111) and δ-Pu(100) through density functional theory

In this work, the initial kinetics of water dissociation on two facets of δ-plutonium, δ-Pu(111) and δ-Pu(100), are explored through density functional theory in order to understand how water dissociation occurs on these facets. We explored the dissociation of water via the formation of hydroxyls, atomic hydrogen, and atomic oxygen species on each facet. We calculate low energetic barriers for water to split to adsorbed hydrogen and hydroxyl species at 0.19 eV for δ-Pu(111) and 0.07 eV for δ-Pu(100). The hydroxyl has a barrier of 0.64 and 0.37 eV to cleave the hydrogen–oxygen bond on δ-Pu(111) and δ-Pu(100), respectively. Due to the highly exergonic adsorption free energy of atomic oxygen of −2.10 eV, the metallic surfaces are found to be fully covered in oxygen, even with the inclusion of oxygen lateral interactions. When combined with the reaction thermodynamics, this free energy of adsorption forms a molecular oxygen desorption barrier greater than 9.51 eV (918 kJ/mol). These results, combined with simulated temperature programed desorption spectra, indicate that oxygen formed via water dissociation on δ-Pu (111) and (100) facets induces an irreversible poison that prevents further reaction of water directly on metallic plutonium surfaces, most likely due to the strong hybridization of the Pu and O valence states. Therefore, these results imply that another mechanism is responsible for the continuously experimentally measured water dissociation, which is most likely due to the Pu oxide.

36 MATERIALS SCIENCE↗

Photothermal alternative to device fabrication using atomic precision advanced manufacturing techniques

The attachment of dopant precursor molecules to depassivated areas of hydrogen-terminated silicon templated with a scanning tunneling microscope (STM) has been used to create electronic devices with subnanometer precision, typically for quantum physics experiments. This process, which we call atomic precision advanced manufacturing (APAM), dopes silicon beyond the solid-solubility limit and produces electrical and optical characteristics that may also be useful for microelectronic and plasmonic applications. However, scanned probe lithography lacks the throughput required to develop more sophisticated applications. In this work, we demonstrate and characterize an APAM device workflow where scanned probe lithography of the atomic layer resist has been replaced by photolithography. An ultraviolet laser is shown to locally and controllably heat silicon above the temperature required for hydrogen depassivation on a nanosecond timescale, a process resistant to under- and overexposure. STM images indicate a narrow range of energy density where the surface is both depassivated and undamaged. Modeling that accounts for photothermal heating and the subsequent hydrogen desorption kinetics suggests that the silicon surface temperatures reached in our patterning process exceed those required for hydrogen removal in temperature-programmed desorption experiments. A phosphorus-doped van der Pauw structure made by sequentially photodepassivating a predefined area and then exposing it to phosphine is found to have a similar mobility and higher carrier density compared with devices patterned by STM. Lastly, it is also demonstrated that photodepassivation and precursor exposure steps may be performed concomitantly, a potential route to enabling APAM outside of ultrahigh vacuum.

nanoscale devices↗

Transformation between elastic dipoles, quadrupoles, octupoles, and hexadecapoles driven by surfactant self-assembly in nematic emulsion

Emulsions comprising isotropic fluid drops within a nematic host are of interest for applications ranging from biodetection to smart windows, which rely on changes of molecular alignment structures around the drops in response to chemical, thermal, electric, and other stimuli. We show that absorption or desorption of trace amounts of common surfactants can drive continuous transformations of elastic multipoles induced by the droplets within the uniformly aligned nematic host. Out-of-equilibrium dynamics of director structures emerge from a controlled self-assembly or desorption of different surfactants at the drop-nematic interfaces, with ensuing forward and reverse transformations between elastic dipoles, quadrupoles, octupoles, and hexadecapoles. We characterize intertransformations of droplet-induced surface and bulk defects, probe elastic pair interactions, and discuss emergent prospects for fundamental science and applications of the reconfigurable nematic emulsions.

36 MATERIALS SCIENCE↗