Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “boundary effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Single-stage stellarator optimization: combining coils with fixed boundary equilibria

We introduce a novel approach for the simultaneous optimization of plasma physics and coil engineering objectives using fixed-boundary equilibria that is computationally efficient and applicable to a broad range of vacuum and finite plasma pressure scenarios. Our approach treats the plasma boundary and coil shapes as independently optimized variables, penalizing the mismatch between the two using a quadratic flux term in the objective function. Four use cases are presented to demonstrate the effectiveness of the approach, including simple and complex stellarator geometries. As shown here, this method outperforms previous two-stage approaches, achieving smaller plasma objective function values when coils are taken into account.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Density modification of cryo-EM maps

Density modification uses expectations about features of a map such as a flat solvent and expected distributions of density in the region of the macromolecule to improve individual Fourier terms representing the map. This process transfers information from one part of a map to another and can improve the accuracy of a map. Here, the assumptions behind density modification for maps from electron cryomicroscopy are examined and a procedure is presented that allows the incorporation of model-based information. Density modification works best in cases where unfiltered, unmasked maps with clear boundaries between the macromolecule and solvent are visible, and where there is substantial noise in the map, both in the region of the macromolecule and the solvent. It also is most effective if the characteristics of the map are relatively constant within regions of the macromolecule and the solvent. Model-based information can be used to improve density modification, but model bias can in principle occur. Here, model bias is reduced by using ensemble models that allow an estimation of model uncertainty. A test of model bias is presented that suggests that even if the expected density in a region of a map is specified incorrectly by using an incorrect model, the incorrect expectations do not strongly affect the final map.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Predicting and Controlling Corrosion (Abbreviated Final Report)

Corrosion accumulates significant replacement costs in the transportation, utility, manufacturing, and infrastructure sectors. It also underpins several of LLNL’s core missions in stockpile stewardship, defense, and energy security. Whereas most corrosion and aging models are empirically parameterized to describe well-defined conditions late in the reaction, the factors that determine the early stages of corrosion—during which mitigation could be most impactful— are poorly understood. This project addressed the critical need for new approaches to predict the kinetics of corrosion initiation based on firm physical and chemical understanding. The activities encompassed degradation of relevant metals in both hydrogen-rich and environmental corrosion scenarios. The team integrated state-of-the-art multiscale simulation, in situ characterization, and data science within three technical thrusts: hydriding of Ti alloys; aqueous corrosion of Al and Ni-Cr alloys; and degradation of additively manufactured 316L stainless steel. In each case, novel capabilities were developed to identify and track the impacts of key atomistic, compositional, and microstructural features on the metal systems. For hydriding, protocols were developed to tightly integrate multiscale models, advanced multimodal characterization, and machine learning to determine how hydrogen interacts with native passivating surface oxides and nucleates new undesired phases, shedding new light on the critical role of grain boundaries, interfaces, and atomically disordered regions. For aqueous corrosion, the project demonstrated methods to predict dissolution rates of metal surfaces in corrosive solutions, to measure and understand microstructural and grain orientation effects on corrosion susceptibility, and to investigate competing growth and dissolution kinetics of surface oxides. For additively manufactured metals, analysis using state-of-the-art microscopy techniques revealed the role of specific heterogeneities invoked during laser processing, including cellular structure, dislocations, and precipitates, on corrosion susceptibility. In addition to new capabilities and understanding, the project provided an avenue for workforce development, as well as key partnerships with stakeholders in corrosion science.

08 HYDROGEN↗
DOE OSTI2023

Boundary Layer Height Variation over the Savannah River Site during a Heat Wave

With the number of heat waves expect to increase in both in their severity and frequency in the coming years, an insight into their impact on planetary boundary layer (PBL) heights is essential for one development of future emergency and safety plans. Using High-Resolution Rapid Refresh (HRRR) atmospheric model output, an analysis is done on the effects a heat wave has on PBL heights and temperature inversions across the Savannah River Site (SRS). This study showed that due to its adjacency to anthropogenic land use, SRS experiences a non-negligible gradient in its PBL height, with higher heights to the northwest. The singular location PBL heigh measurement and forecasts for SRS do not account for this gradient, which has potential implications on pollutant and smoke dispersion onsite. During a heat wave this gradient is present but PBL heights are less impacted than surrounding developed areas, possibly attributable to the woody wetlands that surround the Savannah River's banks. Additionally, the heat wave appears to strongly enhance the nocturnal temperature inversions that the site and surrounding areas experience. This is possibly due to increased stability from higher pressure conditions, which are often associated with heat waves. This influence on nocturnal inversions, however, is limited to their intensity, leaving their timing relatively unaltered. The impact a heat wave has on PBL heights and temperature inversions across SRS is seen to be more dependent on adjacent land use and features rather than the unique land use types onsite.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Center for Alternate Synchronization and Timing (CAST) PTP Network Monitoring Report

The Oak Ridge National Laboratory Center for Alternative Synchronization and Timing (CAST) performs research, development, testing, and evaluation of alternative terrestrial-based timing and synchronization infrastructure for the US power grid and other critical infrastructures. Alternative timing options reduce reliance on GPS and enhance the overall resilience of critical infrastructures. CAST infrastructure uses Precision Time Protocol (PTP) as the primary conduit for delivery of synchronization packets. CAST deploys PTP over long terrestrial links to synchronize a multitude of remote boundary clocks and downstream power grid components with the authoritative grand master clocks. Network traffic issues can severely degrade PTP accuracy. This report focuses on examining network traffic anomalies and their effects on PTP operation as well as the potential implications to CAST’s high-precision remote synchronization operations.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

Two-Frequency RF Fields Induced Multipactor in Coaxial Transmission Lines

Multipactor is a nonlinear discharge phenomenon that occurs in vacuum RF systems, potentially leading to signal distortion, power loss, and even permanent damage to high-power components. This study presents a detailed investigation of two-surface multipactor in coaxial transmission lines under two-frequency excitation, using one-dimensional (1D) Monte Carlo simulations validated by three-dimensional (3D) Particle-in-Cell (PIC) results and experimental data. Introducing a second carrier mode is shown to suppress multipactor by reshaping and shrinking the susceptibility region, with the extent and location of suppression strongly dependent on the device aspect ratio and the relative phase of the second mode. Distinct suppression patterns emerge across different frequency–gap distance (fd) regimes, and in certain cases, susceptibility expansion is also observed. The study identifies and distinguishes pure and mixed multipactor modes in coaxial geometry, where analytical mode boundaries are not readily defined. Unlike planar systems, pure-mode regions in coaxial structures overlap with mixed-mode domains, complicating classification. Image charge forces are found to have minimal effect on susceptibility thresholds but do influence electron growth rates. These findings provide new insights into waveform-driven control of multipactor in high-power RF systems.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Volumetrically Absorbing Thermal Insulator (VATI) for High-temperature Receivers

This project seeks to exploit volumetric absorption of concentrated solar irradiation in a thin, high-temperature, thermally conductive medium. High efficiency thermal conversion is achieved by volumetric absorption of both incoming solar irradiation (short wavelength) and emitted irradiation (long wavelength), demonstrating a volumetrically absorbing thermally insulating (VATI) effect. The thermalized energy is conducted to the back wall, enclosing the working fluid (molten salt or supercritical CO 2 ). Reliance on conductive thermal transport requires a thermally conductive medium, in the absence of which large temperature gradients drive losses due to emission. The project’s outcomes are important to realize a cost-effective approach to reduce optical and thermal losses from CSP receivers at high temperatures (720°C). High-temperature stable and commercially available porous SiC structures (open-cell foams) were explored as a volumetrically absorbing and thermally insulating layer. To the best of our knowledge, the current state-of-the-art for industrially deployed coatings is Pyromark. However, Pyromark suffers degradation at 700+°C and diurnal temperature changes. This necessitates periodic recoating, and the downtime increases the overall levelized cost of energy (LCOE) production. On the other hand, contemporary research activities have generated significant advances in the development of selective emitter coatings, which present challenges with costs, scalability, and stability. The pursued approach alleviates these concerns by developing a receiver that utilizes the inherent structure of high-temperature stable porous materials to enable robust and cost-effective receivers which require no periodic maintenance downtimes. The overall goal of the project is to experimentally demonstrate a figure of merit (FOM) of 0.92 at a temperature of 720°C and solar irradiation of 1000x concentration with porous receivers. The relevant crystallographic (phase) optical and thermal properties of porous SiC were first characterized. Second, the 3-D geometry of the porous SiC was analyzed using micro-X-ray tomography and converted to CAD data using image processing analysis. Utilizing this 3-D geometry and relevant optical/thermal properties, Monte Carlo- Ray Tracing (MCRT) analysis was performed to extract important parameters governing solar-thermal energy conversion such as extinction coefficient (β, 1/m), scattering albedo (ω) and the scattering phase function (Φ). These properties were then integrated into an in-house radiative and conduction transport model to solve for temperature and transport fluxes characterizing the solar-thermal energy conversion. This model was utilized to predict the FOM for various SiC porous geometries and to identify the highest possible FOM. Testing of the optimized porous structures will be accomplished with a custom-built high-accuracy (< ±4%) FOM measurement test-stand and a 1000x solar concentrator. When neglecting convective losses and resistance at the open boundary and the back wall, the optimized SiC foam leads to a FOM of 0.84. This FOM does not surpass the performance of Pyromark 2500. Yet, conversely to Pyromark 2500, SiC is stable at high temperatures and does not degrade over time. Also, it is possible to boost the FOM of SiC by engineering its effective thermal conductivity and its scattering albedo. A FOM of 0.92 is predicted for an optimized foam by accounting for convective losses and resistance at the open boundary and the back wall. This largely exceeds the FOM of Pyromark 2500 (~0.86) predicted by neglecting convective losses and resistance. Therefore, further engineering of the foam could lead to unprecedented FOMs.

14 SOLAR ENERGY↗
DOE OSTI2023

Effects of Aluminum and Molybdenum on the Phase Stability of Iron-Chromium Alloys: A First-Principles Study

The interaction between solute atoms is critical to the thermodynamic behavior of Fe-Cr alloys, but the effects of non-dilute Al and Mo on the Fe-Cr phase stability and vacancy formation energy are not clearly understood. In this study, density functional theory, cluster expansion, and Monte Carlo simulation are used to predict the effects of ternary solute elements on the thermodynamic properties in multicomponent Fe-Cr alloys. The machine learning regression approach is applied to train and construct energy models that accurately describe the complex chemical interactions. The computational outcomes include the prediction of the partial ternary phase diagram, mixing enthalpy, and vacancy formation energy for different compositions. The phase boundary calculation predicts a pronounced change of Cr solubility in bcc Fe by the addition of Al and the rejection of Al atoms from a’ precipitates. The mixing enthalpy calculation shows that Mo may also reduce the Cr solubility in bcc Fe. Additionally, the simulations show that non-dilute Cr decreases the vacancy formation energy in bcc Fe, while adding Al results in a less significant effect. Finally, the results demonstrate important applications of using machine learning energy models to study model or commercial alloys with multicomponent solute species and point defects.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The 3D magnetic topology and plasma dynamics in open stochastic magnetic field lines

We report the thermal quench triggered by locked modes is known to be mainly due to open stochastic magnetic field lines connected to the wall boundary. It is essential to understand the 3D structure of open stochastic field lines since it determines the overall plasma dynamics in the system. In this study, we analyze the 3D magnetic topology for two key concepts, the connection length L c and the effective magnetic mirror ratio M eff , and present a comprehensive picture of electron and ion dynamics related to the magnetic topology. The connection length determines the 3D structure of the ambipolar potential, and a sharp potential drop across distinct L c regions induces the E × B transport and mixing across the field line. The confinement of electrons and ions along the field line is determined by the ambipolar potential and [Formula: see text] configuration. Electron and ion temperatures in magnetic hills (M eff < 1) are lower than in magnetic wells (M eff > 1) because particles in magnetic hills are more likely to escape toward the wall boundary along the field line. The mixing between the magnetic wells and hills by E × B and magnetic drift motions results in collisionless detrapping of electrons and ions, which reduces their temperature efficiently. Numerical simulations of two different magnetic configurations demonstrate the importance of the collisionless detrapping mechanism, which could be the main cause of plasma temperature drop during the thermal quench.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Mesoscale Modeling for Restructuring and Fragmentation in High Burnup UO 2

This report summarizes the mesoscale modeling conducted in fiscal year 2025 under the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, focusing on the microstructural evolution and restructuring in high burnup UO 2 nuclear fuel and its impact on fuel fragmentation. We developed a pioneering phase-field model to simulate restructuring behavior across different regions of high burnup fuel, including the dark zone and rim region. A grand-potential-based phase-field model is employed to concurrently evaluate subgrain formation and the growth of fission gas bubbles within the fuel. An energy-based subgrain formation criterion was introduced to simulate the restructuring process. The effects of temperature and burnup rate were studied to capture how each of these parameters influences the characteristics of the restructured fuel. Subgrain formation was observed to initiate around existing fission gas bubbles and proceed toward triple junctions, grain boundaries, and grain interiors. Under a given subgrain formation rate, the rate of restructuring increases with rising fuel temperature. The restructuring occurs faster with higher burnup rate. A restructuring bias was observed within the microstructure, due to the variation in defect accumulation when comparing different grains. Microstructures corresponding to the dark zone and rim region can be obtained by parameterizing the model with the appropriate defect production rate, as determined based on the burnup rate and temperature. The predicted microstructures are consistent with experimental observations of the restructured regions. Based on the mesoscale simulations, a mechanistic model for restructuring and grain size evolution was implemented in BISON. Thus, this work provides a first-of-its-kind restructuring model for different regions of high-burnup fuel to BISON. It was shown that the model predicts appropriate grain size evolution along fuel radius as those observed in experiments. This model enables BISON to predict the effect of restructuring on the fission gas release. Finally, the phase-field fracture simulation with dark zone specific microstructures were presented to provide the fragmentation criteria for the dark zone. This work introduces a first-of-its-kind restructuring model for high burnup fuel, significantly enhancing BISON's predictive capabilities.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

nn-PINNs: Non-Newtonian physics-informed neural networks for complex fluid modeling

Time- and rate-dependent material functions in non-Newtonian fluids in response to different deformation fields pose a challenge in integrating different constitutive models into conventional computational fluid dynamic platforms. Considering their relevance in many industrial and natural settings alike, robust data-driven frameworks that enable accurate modeling of these complex fluids are of great interest. The main goal is to solve the coupled Partial Differential Equations (PDEs) consisting of the constitutive equations that relate the shear stress to the deformation and fully capture the behavior of the fluid under various flow protocols with different boundary conditions. Here, in this work, we present non-Newtonian physics-informed neural networks (nn-PINNs) for solving systems of coupled PDEs adopted for complex fluid flow modeling. The proposed nn-PINN method is employed to solve the constitutive models in conjunction with conservation of mass and momentum by benefiting from Automatic Differentiation (AD) in neural networks, hence avoiding the mesh generation step. nn-PINNs are tested for a number of different complex fluids with different constitutive models and for several flow protocols. These include a range of Generalized Newtonian Fluid (GNF) empirical constitutive models, as well as some phenomenological models with memory effects and thixotropic timescales. nn-PINNs are found to obtain the correct solution of complex fluids in spatiotemporal domains with good accuracy compared to the ground truth solution. We also present applications of nn-PINNs for complex fluid modeling problems with unknown boundary conditions on the surface, and show that our approach can successfully recover the velocity and stress fields across the domain, including the boundaries, given some sparse velocity measurements.

42 ENGINEERING↗
DOE OSTI2021

Effect of heat treatment on creep behavior of 316 L stainless steel manufactured by laser powder bed fusion

The objective of this study is to understand the thermal stability of microstructure and its effect on the creep behavior of additively-manufactured 316L stainless steel (AM 316L SS). Creep specimens were fabricated from rods printed by a laser powder bed fusion process. Six different heat treatments, namely 650 °C/1 h, 700 °C/1 h, 750 °C/1 h, 800 °C/1 h, 900 °C/1 h and 1050 °C/1 h were applied to the creep specimens. The heat-treated specimens were creep-tested under the same condition, 550 °C/275 MPa to evaluate the effect of post-build heat treatment on the creep behavior of AM 316L SS. In the temperature range of 650-750 °C, dislocation density within cells, and cell size and wall thickness were affected by the heat treatment, while elemental segregation at boundaries remained unchanged and Mn-enriched Si oxide particles remained stable. In the temperature range of 750-900 °C, concurrent changes were observed in dislocation cell structures, elemental segregation and oxide particles. The 1050 °C-heat treatment removed cell structures and boundary solute segregations, leading to formation of equiaxed grains; Mn-enriched Si oxide particles in the as-built specimen were replaced by more stable Mn-enriched Cr oxides. The creep life of AM 316L SS increased after the heat treatment at 650 °C and then decreased with increasing temperature up to 900 °C where cell/subgrain structures still existed. The creep rate and creep elongation followed an opposite trend. The creep rate can be correlated with the structural parameters of cell/subgrain size and cell wall/boundary thickness and can be rationalized by different strengthening mechanisms of dislocation cells and subgrains. The heat treatment affected strongly the primary and secondary creep but had a minimal effect on the tertiary creep of AM 316L SS.

316L stainless steel↗
DOE OSTI2021

Spectroscopic study of the coupling effect between the two gaps of magnesium diboride on its RF properties

This program studied the two-gap nature of magnesium diboride and its possible effects on the superconducting rf properties of this material. Magnesium diboride (MgB 2 ) is a BCS superconductor with a superconducting critical temperature of 39 K, high critical current density and no weak link behavior across the grain boundary. These properties make this material ideal for both power applications and electronic devices. In particular, the high superconducting critical temperature and high thermodynamic field suggests that MgB 2 could be an ideal material also for superconducting radio frequency (SRF) cavities operating at a much higher temperature than Nb cavities and, therefore, reducing noticeably the cryogenics costs. However, MgB 2 is a two gap superconductor and it has been suggested that the RF properties are dominated by the smaller gap, which would make this material not competitive with Nb and especially Nb 3 Sn. The main problem does not seem to be the double-gap nature of this material but rather the weak-coupling of the two gaps that in the presence of an RF field suppresses superconductivity all together at fields much lower than the thermodynamic field. The main goal of this proposal is to address the fundamental question of the coupling between the two gaps in MgB 2 and understand if it is possible to control it and ultimately improve the RF performance of MgB 2 . The project studied these questions by measuring the density of states in the presence of an in-plane current and focused on the effect of controlled disorder. Disorder, indeed, provides an important knob to tune the properties of MgB2 and provides the possibility of changing the coupling between the two bands, making this material a competitive material for SRF applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

A Filon-like integration strategy for calculating exact exchange in periodic boundary conditions: a plane-wave DFT implementation

An efficient and accurate approach for calculating exact exchange and other two-electron integrals has been developed for periodic electronic structure methods. Traditional approaches used for integrating over the Brillouin zone in band structure calculations, e.g. trapezoidal or Monkhorst-Pack, are not accurate enough for two-electron integrals. This is because their integrands contain multiple singularities over the double integration of the Brillouin zone, which with simple integration methods lead to very inaccurate results. A common approach to this problem has been to replace the Coulomb interaction with a screened Coulomb interaction that removes singularities from the integrands in the two-electron integrals, albeit at the inelegance of having to introduce a screening factor which must precomputed or guessed. Instead of introducing screened Coulomb interactions in an ad hoc way, the method developed in this work derives an effective screened potential using a Filon-like integration approach that is based only on the lattice parameters. This approach overcomes the limitations of traditionally defined screened Coulomb interactions for calculating two-electron integrals, and makes chemistry many-body calculations tractable in periodic boundary conditions. This method has been applied to several systems for which conventional DFT methods do not work well, including the reaction pathways for the addition of H 2 to phenol and Au$^{–}_{20}$ nanoparticle, and the electron transfer of a charge trapped state in the Fe(II) containing mica, annite.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Understanding thermal and mechanical effects on lithium plating in lithium-ion batteries

Lithium plating is one of the main concerns for cell durability, as cyclable lithium and cell capacity are decreased during the process. Thermal and mechanical loads can influence cell behavior, including lithium plating driving forces, as suggested by the Arrhenius equation and the Bruggeman relation, respectively. Hence, a 1D and a 3D model are employed to study the thermal and mechanical effects on lithium plating in a lithium-ion battery with a high areal capacity (4 mAh/cm 2 ). The 1D model assumes uniform mechanical and temperature profile, while the 3D model is capable of capturing the nonuniformity of stress and temperature in the cell. Further, the effects of mechanical deformation and different temperatures on the process of lithium plating are investigated in this study. With the help of the 1D charging simulations, it is observed that lower temperatures increase the risk of lithium plating and the presence of mechanical deformations can accelerate its initiation. Furthermore, 3D charging simulations indicated that folds and boundaries of jellyrolls are more susceptible to lithium plating due to the higher stress concentration and lower temperature, respectively.

25 ENERGY STORAGE↗
DOE OSTI2021

The effects of free surfaces on deformation twinning in HCP metals

Deformation twinning is a predominant mode of plastic deformation for hexagonal close packed metals, like Mg and Ti. The heterogenous microstructure and the local stresses associated with twinning play a key role in their mechanical response and fracture. Surface analyses, like electron microscopy, are frequently employed to spatially map microstructure and micromechanical fields in order to study twinning behavior. However, these measurements are inherently influenced by the vicinity of the free surface. In this work, an elasto-visco-plastic fast-Fourier-transform (EVP-FFT) polycrystal modeling approach is employed to investigate the effects of free surfaces on twin development before and after loading. We compare calculated micromechanical fields on free surfaces with those calculated inside the bulk and, in some cases, experimental surface measurements. The results indicate that the creation of free surfaces can promote twin propagation and growth and can influence twin morphology by causing a twin lamella to become larger, more blunted and irregular. The structure along the twin boundaries are also affected, due to the higher driving stresses that extend prismatic-basal and basal-prismatic facets. Furthermore, free surfaces invoke different slip activities in the twin and the surrounding parent crystal by enhancing basal, prismatic and pyramidal slip in some localized regions, while reducing slip in others. We demonstrate that the simulated free-surface effects lead to better qualitative and quantitative agreement with experimental measurements from scanning electron microscopy and digital image correlation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Post-Minkowskian effective field theory for conservative binary dynamics

We develop an Effective Field Theory (EFT) formalism to solve for the conservative dynamics of binary systems in gravity via Post-Minkowskian (PM) scattering data. Our framework combines a systematic EFT approach to compute the deflection angle in the PM expansion, together with the ‘Boundary-to-Bound’ (B2B) dictionary introduced. Due to the nature of scattering processes, a remarkable reduction of complexity occurs both in the number of Feynman diagrams and type of integrals, compared to a direct EFT computation of the potential in a PM scheme. We provide two illustrative examples. Firstly, we compute all the conservative gravitational observables for bound orbits to 2PM, which follow from only one topology beyond leading order. The results agree with those, obtained through the ‘impetus formula’ applied to the classical limit of the one loop amplitude. For the sake of comparison we reconstruct the conservative Hamiltonian to 2PM order, which is equivalent to the one derived from a matching calculation. Secondly, we compute the scattering angle due to tidal effects from the electric- and magnetic-type Love numbers at leading PM order. Using the B2B dictionary we then obtain the tidal contribution to the periastron advance. We also construct a Hamiltonian including tidal effects at leading PM order. Although relying on (relativistic) Feynman diagrams, the EFT formalism developed here does not involve taking the classical limit of a quantum amplitude, neither integrals with internal massive fields, nor additional matching calculations, nor spurious (‘super-classical’) infrared singularities. By construction, the EFT approach can be automatized to all PM orders.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Escalated Phase Separation Driven Enhanced Magnetoresistance in Manganite/Iridate Epitaxial Heterostructures

Phase separation in manganites leads to unique magnetic and electronic properties. 50% Ca-doped LaMnO 3 (LCMO), at the boundary of ferromagnetic (FM) and antiferromagnetic (AFM) states in La 1-x Ca x MnO 3 (0 ≤ x ≤ 1), is an ideal system to study phase separation behavior. The investigation reveals the effect of a 5d-metal perovskite SrIrO 3 (SIO) on the phase separation, magnetic, and magnetoresistance (MR) properties of LCMO. Single-layer and bilayer LCMO films, both appear purely ferromagnetic along the in-plane (IP) magnetic field direction, but show the tendency of temperature-dependent ferromagnetic and antiferromagnetic or charge-ordered (CO) phase separation with the out-of-plane (OOP) applied field. The MR, and colossal magnetoresistance (CMR), observed in LCMO/SIO bilayers are two orders and an order of magnitude (in %) larger, respectively than that in the single-layer film. The coexistence of FM and AFM/CO phases is responsible for the CMR and MR enhancement in the LCMO/SIO bilayer, pointing toward the importance of the phase separation and competition of both the individual materials in enhancing their magnetic and electronic properties.

36 MATERIALS SCIENCE↗