Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
NASA NTRS1958

Correlations Among Ice Measurements, Impingement Rates Icing Conditions, and Drag Coefficients for Unswept NACA 65A004 Airfoil

An empirical relation has been obtained by which the change in drag coefficient caused by ice formations on an unswept NACA 65AO04 airfoil section can be determined from the following icing and operating conditions: icing time, airspeed, air total temperature, liquid-water content, cloud droplet impingement efficiencies, airfoil chord length, and angles of attack. The correlation was obtained by use of measured ice heights and ice angles. These measurements were obtained from a variety of ice formations, which were carefully photographed, cross-sectioned, and weighed. Ice weights increased at a constant rate with icing time in a rime icing condition and at progressively increasing rates in glaze icing conditions. Initial rates of ice collection agreed reasonably well with values predicted from droplet impingement data. Experimental droplet impingement rates obtained on this airfoil section agreed with previous theoretical calculations for angles of attack of 40 or less. Disagreement at higher angles of attack was attributed to flow separation from the upper surface of the experimental airfoil model.

Gray, Vernon H.↗
NASA NTRS1985

Evaluation of a stalled airfoil analysis program

The Stalled Airfoil Analysis Program (SAAP) is a computer code for predicting the aerodynamic characteristics of an airfoil up to, and beyond, stall. SAAP is presently evaluated through comparisons with experiments and with two other theoretical methods over an extensive range of airfoils and Reynolds number conditions. SAAP modeled drag more accurately than either of the other methods, and at angles of attack below stall yielded a smoother lift variation with angle of attack.

Rumsey, C. L.↗
NASA NTRS1987

Two-dimensional aerodynamic characteristics of the AMES HI-120, HI-8, and LOW-12 airfoils

During the period between June and September 1986, the Aeronautical and Astronautical Engineering Research Laboratory (AARL) at the Ohio State University (OSU) in Columbus, Ohio, conducted tests in the 6"X22" Transonic Blowdown Wind Tunnel to determine the two-dimensional lift, drag, and pitching moment coefficients for three airfoils designated AMES HI-120, AMES LOW-12, and AMES HI-8. These tests covered a Mach number range of 0.20 to 0.86, Reynolds numbers between 2 x 10 to the 6th and 6 x 10 to the 6th powers, and angles of attack between 0 and 13 degs as directed by the NASA Project Engineer; each model was not run at every condition. This work was performed under NASA Grant NAG-2-401, Analysis of Two Advanced Transonic Airfoils.

Gregorek, G. M.↗
NASA NTRS1987

Theoretical approach to oxygen atom degradation of silver

Based on available Rutherford backscattering spectrometry (RBS), proton induced X-ray emission (PIXE) and ellipsometry data obtained on silver specimens subjected to atomic oxygen attack in low Earth orbit STS flight 41-G, a theory was developed to model the oxygen atom degradation of silver. The diffusion of atomic oxygen in a microscopically nonuniform medium is an essential constituent of the theory. The driving force for diffusion is the macroscopic electrochemical potential gradient developed between the specimen surface exposed to the ambient and the bulk of the silver specimen. The longitudinal electric effect developed parallel to the gradient is modified by space charge of the diffusing charged species. Lateral electric fields and concentration differences also exist due to the nonuniform nature of the medium. The lateral concentration differences are found to be more important than the lateral electric fields in modifying the diffusion rate. The model was evaluated numerically. Qualitative agreement exists between the kinetics predicted by the theory and kinetic data taken in ground-based experiments utilizing a plasma asher.

Fromhold, Albert T., Jr.↗
NASA NTRS1987

Numerical simulations of aerodynamic contribution of flows about a space-plane-type configuration

The slightly supersonic viscous flow about the space-plane under development at the National Aerospace Laboratory (NAL) in Japan was simulated numerically using the LU-ADI algorithm. The wind-tunnel testing for the same plane also was conducted with the computations in parallel. The main purpose of the simulation is to capture the phenomena which have a great deal of influence to the aerodynamic force and efficiency but is difficult to capture by experiments. It includes more accurate representation of vortical flows with high angles of attack of an aircraft. The space-plane shape geometry simulated is the simplified model of the real space-plane, which is a combination of a flat and slender body and a double-delta type wing. The comparison between experimental results and numerical ones will be done in the near future. It could be said that numerical results show the qualitatively reliable phenomena.

Matsushima, Kisa↗
NASA NTRS1992

Report on the final panel discussion on computational aeroacoustics

Some important conclusions about future prospects for aeroacoustics in general, and for computational aeroacoustics in particular, that were reached in the course of the Final Panel Discussion of the Workshop on Computational Aeroacoustics held from 6 to 9 April 1992 by ICASE and NASA Langley Research Center are summarized by the panel chairman. Aeroacoustics must now be involved in interactions with computational fluid dynamics (as applied not only to deterministic flows but also to the statistical characteristics of turbulence), while additionally incorporating rigorous comparisons with experiment. The new Computational Aeroacoustics will press forward in two parallel ways. In one of them, CFD will be used to determine aeroacoustic source strengths, the associated radiation being derived by the Acoustic Analogy approach in one of its forms. In the other, a direct Computational Aeroacoustics will apply CFD techniques over a region extending beyond the flow field so as to include at least the beginnings of the acoustic far field. There are some particularly important areas of study, including rotor noise, boundary-layer noise, and the noise of supersonic jets, where it is strongly recommended that use of both methods is continued. On the other hand, important problems of the diffraction of radiation from aeroacoustic sources around complicated aircraft shapes will require the use of comprehensively Computational Aeroacoustics, while Acoustic Analogy methods seem better suited to estimating subsonic jet noise. The study of model problems to allow comparisons with experiment will be valuable in both lines of attack.

Lighthill, James↗
NASA NTRS1993

A high-fidelity, six-degree-of-freedom batch simulation environment for tactical guidance research and evaluation

A batch air combat simulation environment, the tactical maneuvering simulator (TMS), is presented. The TMS is a tool for developing and evaluating tactical maneuvering logics, but it can also be used to evaluate the tactical implications of perturbations to aircraft performance or supporting systems. The TMS can simulate air combat between any number of engagement participants, with practical limits imposed by computer memory and processing power. Aircraft are modeled using equations of motion, control laws, aerodynamics, and propulsive characteristics equivalent to those used in high-fidelity piloted simulations. Data bases representative of a modern high-performance aircraft with and without thrust-vectoring capability are included. To simplify the task of developing and implementing maneuvering logics in the TMS, an outer-loop control system, the tactical autopilot (TA), is implemented in the aircraft simulation model. The TA converts guidance commands by computerized maneuvering logics from desired angle of attack and wind-axis bank-angle inputs to the inner loop control augmentation system of the aircraft. The capabilities and operation of the TMS and the TA are described.

Goodrich, Kenneth H.↗
NASA NTRS1946

An Experimental Investigation of Flow Conditions in the Vicinity of an NACA D(sub S)-type Cowling

Data are presented of the flow conditions in the vicinity of an NACA D sub S -type cowling. Tests were made of a 1/2 scale-nacelle model at inlet-velocity ratios ranging from 0.23 to 1.02 and angles of attack from 6 deg to 10 deg. The velocity and direction of flow in the vertical plane of symmetry of the cowling were determined from orifices and tufts installed on a board aligned with the flow. Diagrams showing velocity ratio contours and lines of constant flow angles are given.

FLAPPED↗
NASA NTRS1996

Soft Computing Methods in Design of Superalloys

Soft computing techniques of neural networks and genetic algorithms are used in the design of superalloys. The cyclic oxidation attack parameter K(sub a), generated from tests at NASA Lewis Research Center, is modelled as a function of the superalloy chemistry and test temperature using a neural network. This model is then used in conjunction with a genetic algorithm to obtain an optimized superalloy composition resulting in low K(sub a) values.

Cios, K. J.↗
NASA NTRS1995

Soft computing methods in design of superalloys

Soft computing techniques of neural networks and genetic algorithms are used in the design of superalloys. The cyclic oxidation attack parameter K(sub a), generated from tests at NASA Lewis Research Center, is modeled as a function of the superalloy chemistry and test temperature using a neural network. This model is then used in conjunction with a genetic algorithm to obtain an optimized superalloy composition resulting in low K(sub a) values.

Cios, K. J.↗
NASA NTRS2000

A Reconfiguration Scheme for Accommodating Actuator Failures in Multi-Input, Multi-Output Flight Control Systems

A multi-input, multi-output reconfigurable flight control system design utilizing a robust controller and an adaptive filter is presented. The robust control design consists of a reduced-order, linear dynamic inversion controller with an outer-loop compensation matrix derived from Quantitative Feedback Theory (QFT). A principle feature of the scheme is placement of the adaptive filter in series with the QFT compensator thus exploiting the inherent robustness of the nominal flight control system in the presence of plant uncertainties. An example of the scheme is presented in a pilot-in-the-loop computer simulation using a simplified model of the lateral-directional dynamics of the NASA F18 High Angle of Attack Research Vehicle (HARV) that included nonlinear anti-wind up logic and actuator limitations. Prediction of handling qualities and pilot-induced oscillation tendencies in the presence of these nonlinearities is included in the example.

Siwakosit, W.↗
NASA NTRS2003

Control of Interacting Vortex Flows at Subsonic and Transonic Speeds Using Passive Porosity

A wind tunnel experiment was conducted in the NASA Langley Research Center (LaRC) 8-foot Transonic Pressure Tunnel (TPT) to determine the effects of passive surface porosity on vortex flow interactions about a general research fighter configuration at subsonic and transonic speeds. Flow- through porosity was applied to a wind leading-edge extension (LEX) mounted to a 65 deg cropped delta wind model to promote large nose-down pitching moment increments at high angles of attack. Porosity decreased the vorticity shed from the LEX, which weakened the LEX vortex and altered the global interactions of the LEX and wing vortices at high angles of attack. Six-component forces and moments and wing upper surface static pressure distributions were obtained at free- stream Mach numbers of 0.50, 0.85, and 1.20, Reynolds number of 2.5(10(exp-6) per foot, angles of attack up to 30 deg and angles of sideslip to plus or minus 8 deg. The off-surface flow field was visualized in selected cross-planes using a laser vapor screen flow visualization technique. Test data were obtained with a centerline vertical tail and with alternate twin, wing-mounted vertical fins having 0 deg and 30 deg cant angles. In addition, the porosity of the LEX was compartmentalized to determine the sensitivity of the vortex- dominated aerodynamics to the location and level of porosity applied to the LEX.

NATO FURNISHED↗
NASA NTRS2003

Control of Interacting Vortex Flows at Subsonic and Transonic Speeds Using Passive Porosity

A wind tunnel experiment was conducted in the NASA Langley Research Center (LaRC) 8-Foot Transonic Pressure Tunnel (TPT) to determine the effects of passive surface porosity on vortex flow interactions about a general research fighter configuration at subsonic and transonic speeds. Flow-through porosity was applied to a wing leading-edge extension (LEX) mounted to a 65 deg cropped delta wing model to promote large nose-down pitching moment increments at high angles of attack. Porosity decreased the vorticity shed from the LEX, which weakened the LEX vortex and altered the global interactions of the LEX and wing vortices at high angles of attack. Six-component forces and moments and wing upper surface static pressure distributions were obtained at free-stream Mach numbers of 0.50, 0.85, and 1.20, Reynolds number of 2.5(10(exp 6)) per foot, angles of attack up to 30 deg, and angles of sideslip to +/- 8 deg. The off-surface flow field was visualized in selected cross-planes using a laser vapor screen flow visualization technique. Test data were obtained with a centerline vertical tail and with alternate twin, wing-mounted vertical fins having 0 deg and 30 deg cant angles. In addition, the porosity of the LEX was compartmentalized to determine the sensitivity of the vortex-dominated aerodynamics to the location and level of porosity applied to the LEX.

Erickson, Gary E.↗
NASA NTRS1953

Lateral Oscillatory Characteristics of the Republic F-91 Airplane Calculated by Using Low-Speed Experimental Static and Rotary Derivatives

The present investigation was conducted to determine, from low-speed tests in the Langley stability tunnel, the static and rotary derivatives of a 1/9-scale model of the Republic F-91 airplane and various of its components (including the effects of wing incidence) and to determine the accuracy with which the period and damping of the lateral oscillation of the airplane could be calculated by using these experimentally between flight and calculated period and damping of the lateral oscillation were made for Mach numbers from 0.4 to 0.9 at an altitude of 20,OOO feet for 0deg wing incidence and several other wing incidences. Some comparisons were made of the static and rotary derivatives of the model and derivatives estimated by available procedures. determined derivatives (corrected for Mach number effects). Comparisons The results of the investigation have indicated that the model did not have unusual aerodynamic characteristics except for a large (about -0.125) increment in the damping in yaw contributed by the fuselage. Changes in wing incidence, in general, had little effect on the static and rotary derivatives of the model. The static and rotary derivatives of the model could be estimated with good accuracy only in the low angle-of-attack range by using available procedures.

Jaquet, Byron M.↗
NASA NTRS2006

Uncertainty Analysis for a Jet Flap Airfoil

An analysis of variance (ANOVA) study was performed to quantify the potential uncertainties of lift and pitching moment coefficient calculations from a computational fluid dynamics code, relative to an experiment, for a jet flap airfoil configuration. Uncertainties due to a number of factors including grid density, angle of attack and jet flap blowing coefficient were examined. The ANOVA software produced a numerical model of the input coefficient data, as functions of the selected factors, to a user-specified order (linear, 2-factor interference, quadratic, or cubic). Residuals between the model and actual data were also produced at each of the input conditions, and uncertainty confidence intervals (in the form of Least Significant Differences or LSD) for experimental, computational, and combined experimental / computational data sets were computed. The LSD bars indicate the smallest resolvable differences in the functional values (lift or pitching moment coefficient) attributable solely to changes in independent variable, given just the input data points from selected data sets. The software also provided a collection of diagnostics which evaluate the suitability of the input data set for use within the ANOVA process, and which examine the behavior of the resultant data, possibly suggesting transformations which should be applied to the data to reduce the LSD. The results illustrate some of the key features of, and results from, the uncertainty analysis studies, including the use of both numerical (continuous) and categorical (discrete) factors, the effects of the number and range of the input data points, and the effects of the number of factors considered simultaneously.

Green, Lawrence L.↗
NASA NTRS2008

Active Flow Control at Low Reynolds Numbers on a NACA 0015 Airfoil

Results from a low Reynolds number wind tunnel experiment on a NACA 0015 airfoil with a 30% chord trailing edge flap tested at deflection angles of 0, 20, and 40 are presented and discussed. Zero net mass flux periodic excitation was applied at the ap shoulder to control flow separation for flap deflections larger than 0. The primary objective of the experiment was to compare force and moment data obtained from integrating surface pressures to data obtained from a 5-component strain-gage balance in preparation for additional three-dimensional testing of the model. To achieve this objective, active flow control is applied at an angle of attack of 6 where published results indicate that oscillatory momentum coefficients exceeding 1% are required to delay separation. Periodic excitation with an oscillatory momentum coefficient of 1.5% and a reduced frequency of 0.71 caused a significant delay of separation on the airfoil with a flap deflection of 20. Higher momentum coefficients at the same reduced frequency were required to achieve a similar level of flow attachment on the airfoil with a flap deflection of 40. There was a favorable comparison between the balance and integrated pressure force and moment results.

Melton, LaTunia Pack↗
NASA NTRS2012

Evaluation of Icing Scaling on Swept NACA 0012 Airfoil Models

Icing scaling tests in the NASA Glenn Icing Research Tunnel (IRT) were performed on swept wing models using existing recommended scaling methods that were originally developed for straight wing. Some needed modifications on the stagnation-point local collection efficiency (i.e., beta(sub 0) calculation and the corresponding convective heat transfer coefficient for swept NACA 0012 airfoil models have been studied and reported in 2009, and the correlations will be used in the current study. The reference tests used a 91.4-cm chord, 152.4-cm span, adjustable sweep airfoil model of NACA 0012 profile at velocities of 100 and 150 knot and MVD of 44 and 93 mm. Scale-to-reference model size ratio was 1:2.4. All tests were conducted at 0deg angle of attack (AoA) and 45deg sweep angle. Ice shape comparison results were presented for stagnation-point freezing fractions in the range of 0.4 to 1.0. Preliminary results showed that good scaling was achieved for the conditions test by using the modified scaling methods developed for swept wing icing.

Tsao, Jen-Ching↗
NASA NTRSDate not supplied

Assessment of Control Algorithms for Mars Entry Vehicles With Flap-Based Trajectory Control Under Uncertainty

Flap-based steering systems on blunt-body entry vehicles may improve flight performance relative to heritage bank-angle steering systems. Successful implementation of articulating aerodynamic flaps on a hypersonic entry vehicle requires an active control system to map angle of attack and sidelip angle commands to flap deflection commands. Here, a successive-linearization model prective control algorithm, as a linear quadratic regulator, are formulated, designed, and assessed to address this multiple input multiple output control problem. These two control algorithms are assessed under uncertainty in Monte Carlo simulations for various control profiles and vehicle configurations. Results indicate that while both control algorithms provide successful command tracking under uncertainty, the model predictive controller provides a lower mean and integral error, as well as greater robustness, relative to the linear-quadratic regulator.

Daniel L Engel↗