Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Variational approach”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Conceptual Design Trade Studies for Acoustic Predictions of the NASA UAM Tiltrotor Reference Vehicle

A toolchain of low-and mid-fidelity tools is applied to NASA’s Urban Air Mobility tiltrotor reference vehicle to quantify trades in sizing, performance, and noise at the conceptual design level. The process includes conceptual sizing, comprehensive analysis, and acoustic analysis to design and analyze versions of the concept tiltrotor with differing design variables. Rotor tip speed is the primary design variable studied, with blade twist, blade taper, and blade number also considered. The noise metrics used are the FAA/EASA certification Effective Perceived Noise Levels for takeoff, flyover, and approach. Certification condition noise is calculated for all conditions in both conversion and airplane flight modes, with airplane mode flight resulting in noise 10-25EPNdB quieter than conversion mode and tip speed variation providing noise reduction up to 9EPNdB.

Acoustic↗

A Physics of Failure Approach to Evaluate Printed Circuit Board Reliability

Risk based technology infusion is a deliberate and systematic process which defines the analysis and communication methodology by which new technology is applied and integrated into existing and new designs, identifies technology development needs based on trends analysis and facilitates the identification of shortfalls against performance objectives. This presentation at IPC Works Asia Aerospace 2019 Events provides the audience a snapshot of quality variations in printed wiring board quality, as assessed, using experiences in processing and risk analysis of PWB structural integrity coupons. The presentation will focus on printed wiring board quality metrics used, the relative type and number of non-conformances observed and trend analysis using statistical methods. Trend analysis shows the top five non-conformances observed across PWB suppliers, the root cause(s) behind these non-conformance and suggestions of mitigation plans. The trends will then be matched with the current state of the PWB supplier base and its challenges and opportunities. The presentation further discusses the risk based SMA approaches and methods being applied at GSFC for evaluating candidate printed wiring board technologies which promote the adoption of higher throughput and faster processing technology for GSFC missions.

Printed Circuit Boards↗

A piloted simulator investigation of stability and control, display and crew-loading requirements for helicopter instrument approach. Part 1: Technical discussion and results

A ground-simulation experiment was conducted to investigate the influence and interaction of flight-control system, fight-director display, and crew-loading situation on helicopter flying qualities during terminal area operations in instrument conditions. The experiment was conducted on the Flight Simulator for Advanced Aircraft at Ames Research Center. Six levels of control complexity, ranging from angular rate damping to velocity augmented longitudinal and vertical axes, were implemented on a representative helicopter model. The six levels of augmentation were examined with display variations consisting of raw elevation and azimuth data only, and of raw data plus one-, two-, and three-cue flight directors. Crew-loading situations simulated for the control-display combinations were dual-pilot operation (representative auxiliary tasks of navigation, communications, and decision-making). Four pilots performed a total of 150 evaluations of combinations of these parameters for a representative microwave landing system (MLS) approach task.

Lebacqz, J. V.↗

Constraints on Triple Oxygen Isotope Kinetics

Triple oxygen isotope methods (e.g., using δ 18 O, and Δ′ 17 O) have been used to classify meteorites, to constrain atmospheric chemistry, and to estimate primary productivity, among other uses. Such utility relies on the mass dependency of most chemical reactions: δ 17 O is proportional to δ 18 O by roughly a factor of 0.5. However, in detail, mass-dependency factors vary. While constraints on mass dependency are well established for equilibrium isotope effects, similar constraints for kinetic isotope effects are lacking. Using an ab initio Monte Carlo approach (see envelopes in Figure 1), we find the range of kinetic isotope effects (i.e., resulting from unidirectional chemical reactions) contains and exceeds the range of accessible equilibrium isotope effects for the 16 O 17 O 18 O system (Hayles and Killingsworth, 2022). Accessible kinetic isotope effects can yield Δ′ 17 O variations as large 0.8 ‰ from a single kinetic fractionation step. Reactions that yield the largest deviations from equilibrium are those with the largest molecular mass difference between decomposition fragments, typically the two products such as a gas and solid generated from the thermal decomposition of an initial solid. Comparison of DFT transition state model results against previously published experiments on the thermal decomposition of calcite (CaCO 3 ) (Miller et al., 2002) and dehydroxylation of brucite (Mg(OH) 2 ) (Clayton and Mayeda, 2009) show they are matched with mass-dependent kinetic isotope effects. This approach can be applied to any system with more than two isotopes.

Oxygen isotopes↗

Characterizing spatiotemporal patterns of crop phenology across North America during 2000–2016 using satellite imagery and agricultural survey data

Crop phenology represents an integrative indicator of climate change and plays a vital role in terrestrial carbon dynamics and sustainable agricultural development. However, spatiotemporal variations of crop phenology remain unclear at large scales. This knowledge gap has hindered our ability to realistically quantify the biogeochemical dynamics in agroecosystems, predict future climate, and make informed decisions for climate change mitigation and adaptation. In this study, we improved an EVI-curve-based approach and used it to detect spatiotemporal patterns in cropping intensity and five major phenological stages over North America during 2000–2016 using vegetation index in combination with agricultural survey data and other ancillary maps. Our predicted crop phenological stages showed strong linear relationships with the survey-based datasets, with R(exp 2), RMSEs, and MAEs in the ranges of 0.35 –0.99, three to ten days, and two to eight days, respectively. During the study period, the planting dates were advanced by 0.60 days/year (p < 0.01), and harvesting dates were delayed by 0.78 days/year (p < 0.01) over North America. A minimum temperature increase by 1 °C caused a 4.26-day planting advance (r = −0.50, p < 0. 01) or a 0.66-day harvest delay (r = 0.10, p < 0.01). While, a higher maximum temperature resulted in a planting advance by 4.48 days/°C (r = −0.62, p < 0.01) or a harvest advance by 2.22 days/°C (r = −0.40, p < 0.01). Our analysis illustrated evident spatiotemporal variations in crop phenology in response to climate change and management practices. The derived crop phenological datasets and cropping intensity maps can be used in regional climate assessments and in developing adaptation strategies.

North America↗

A finite element model of conduction, convection, and phase change near a solid/melt interface

Detailed understanding of heat transfer and fluid flow is required for many aerospace thermal systems. These systems often include phase change and operate over a range of accelerations or effective gravitational fields. An approach to analyzing such systems is presented which requires the simultaneous solution of the conservation laws of energy, momentum, and mass, as well as an equation of state. The variable property form of the governing equations are developed in two-dimensional Cartesian coordinates for a Newtonian fluid. A numerical procedure for solving the governing equations is presented and implemented in a computer program. The Galerkin form of the finite element method is used to solve the spatial variation of the field variables, along with the implicit Crank-Nicolson time marching algorithm. Quadratic Langrangian elements are used for the internal energy and the two components of velocity. Linear Lagrangian elements are used for the pressure. The location of the solid/liquid interface as well as the temperatures are determined form the calculated internal energy and pressure. This approach is quite general in that it can describe heat transfer without phase change, phase change with a sharp interface, and phase change without an interface. Analytical results from this model are compared to those of other researchers studying transient conduction, convection, and phase change and are found to be in good agreement. The numerical procedure presented requires significant computer resources, but this is not unusual when compared to similar studies by other researchers. Several methods are suggested to reduce the computational times.

Viterna, Larry A.↗

Multitemporal and geobotanical approach in the remote detection of Greisenization areas in the Serra da Pedra Branca Granite, Goias State, Brazil

A multiseasonal analysis of LANDSAT multispectral images in CCT format permitted the mapping of lithologic facies in the Pedra Branca Granite, using geobotanical associations, which occur in the form of variations in the density of the cerrado vegetation, as well as the predominance of certain distinct vegetation species. Dry season images did not show very good results in lithological differentiation due to anomalous illumination conditions related to the low solar elevation and the homogeneity in the vegetation cover, specially the grass that becomes dry during this season. Rainy season images, on the other hand, allowed the separation of the lithological types, a fact that can be attributed to a greater differentiation among the geobotanical associations. The muscovite-granite facies with greisenization zones within the Serra da Pedra Branca were mapped. This methodology can be successfully applied to similar known granite bodies elsewhere in the Tin Province of Goias.

Parada, N. D. J.↗

Acoustic fatigue - A Monte Carlo approach

The present paper reviews the basic concepts of nonlinear structural response to surface flow and acoustic pressure inputs. A time domain solution and the Monte Carlo method are utilized to estimate the required statistics of the nonlinear response. Simulation procedures of multi-dimensional and multi-variate random processes are discussed. Application of these procedures to acoustic fatigue of flight structures are considered. Numerical examples are included to illustrate the applicability of this method for the solution of nonlinear problems.

Vaicaitis, R.↗

Fabrication Method for LOBSTER-Eye Optics in <110> Silicon

Soft x-ray optics can use narrow slots to direct x-rays into a desirable pattern on a focal plane. While square-pack, square-pore, slumped optics exist for this purpose, they are costly. Silicon (Si) is being examined as a possible low-cost replacement. A fabrication method was developed for narrow slots in <110> Si demonstrating the feasibility of stacked slot optics to replace micropores. Current micropore optics exist that have 20-micron-square pores on 26-micron pitch in glass with a depth of 1 mm and an extent of several square centimeters. Among several proposals to emulate the square pore optics are stacked slot chips with etched vertical slots. When the slots in the stack are positioned orthogonally to each other, the component will approach the soft x-ray focusing observed in the micropore optics. A specific improvement Si provides is that it can have narrower sidewalls between slots to permit greater throughput of x-rays through the optics. In general, Si can have more variation in slot geometry (width, length). Further, the sidewalls can be coated with high-Z materials to enhance reflection and potentially reduce the surface roughness of the reflecting surface. Narrow, close-packed deep slots in <110> Si have been produced using potassium hydroxide (KOH) etching and a patterned silicon nitride (SiN) mask. The achieved slot geometries have sufficient wall smoothness, as observed through scanning electron microscope (SEM) imaging, to enable evaluation of these slot plates as an optical element for soft x-rays. Etches of different angles to the crystal plane of Si were evaluated to identify a specific range of etch angles that will enable low undercut slots in the Si <110> material. These slots with the narrow sidewalls are demonstrated to several hundred microns in depth, and a technical path to 500-micron deep slots in a precision geometry of narrow, closepacked slots is feasible. Although intrinsic stress in ultrathin wall Si is observed, slots with walls approaching 1.5 microns can be achieved (a significant improvement over the 6-micron walls in micro - pore optics). The major advantages of this technique are the potential for higher x-ray throughout (due to narrow slot walls) and lower cost over the existing slumped micropore glass plates. KOH etching of smooth sidewalls has been demonstrated for many applications, suggesting its feasibility for implementation in x-ray optics. Si cannot be slumped like the micropore optics, so the focusing will be achieved with millimeter-scale slot plates that populate a spherical dome. The possibility for large-scale production exists for Si parts that is more difficult to achieve in micropore parts.

Chervenak, James↗

Task 6: IFYGL (lake Ontario), 1384

The author has identified the following significant results. The Lake Ontario drainage basin covers over 32,000 miles of U.S. and Canadian territory. ERTS-1 data is contributing to the comprehensive study of this basin as part of the International Field Year for the Great Lakes (IFYGL). A processing approach is described for obtaining detailed and objective synoptive synoptic information thought to be applicable to terrestrial water balance studies of such a large area. A simple ratio algorithm was tested for minimizing daily variations in ERTS-1 data and for allowing the discrimination of surface features and land use classes of hydrologic significance. These steps are necessary if ERTS-1 data is to provide the quantitative information required for the study and management of areas of regional size.

Polcyn, F. C.↗

Compensating for environmental variability in the thermal inertia approach to remote sensing of soil moisture

A procedure is developed for removing data scatter in the thermal-inertia approach to remote sensing of soil moisture which arises from environmental variability in time and space. It entails the utilization of nearby National Weather Service air temperature measurements to normalize measured diurnal surface temperature variations to what they would have been for a day of standard diurnal air temperature variation, arbitrarily assigned to be 18 C. Tests of the procedure's basic premise on a bare loam soil and a crop of alfalfa indicate it to be conceptually sound. It is possible that the technique could also be useful in other thermal-inertia applications, such as lithographic mapping.

Idso, S. B.↗

Sound propagation through nonuniform ducts

Methods of determining the transmission and attenuation of sound propagating in nonuniform ducts with and without mean flows are discussed. The approaches reviewed include purely numerical techniques, quasi-one-dimensional approximations, solutions for slowly varying cross sections, solutions for weak wall undulations, approximation of the duct by a series of stepped uniform cross sections, variational methods and solutions for the mode envelopes.

Nayfeh, A. H.↗

Postbuckling of laminated anisotropic panels

A two-part study of the buckling and postbuckling of laminated anisotropic plates with bending-extensional coupling is presented. The first part involves the development and application of a modified Rayleigh-Ritz analysis technique. Modifications made to the classical technique can be grouped into three areas. First, known symmetries of anisotropic panels are exploited in the selection of approximation functions. Second, a reduced basis technique based on these same symmetries is applied in the linear range. Finally, geometric boundary conditions are enforced via an exterior penalty function approach, rather than relying on choice of approximation functions to satisfy these boundary conditions. Numerical results are presented for both the linear and nonlinear range, with additional studies made to determine the effect of variation in penalty parameter and number of basis vectors. In the second part, six panels possessing anisotropy and bending-extensional coupling are tested. Detailed comparisons are made between experiment and finite element results in order to gain insight into the postbuckling and failure characteristics of such panels. The panels are constructed using two different lamination sequences, and panels with three different aspect ratios were constructed for each lamination sequence.

Jeffrey, Glenda L.↗

Nucleus of Comet IRAS-Araki-Alcock (1983 VII)

Optical, radar, infrared, UV, and microwave-continuum observations of Comet IRAS-Araki-Alcok were obtained in May 1983, the week of the comet's close approach to earth. The comet has a nucleus dimension and a rotation period which are similar to those of Comet Halley, but a different morphological signature (a persisting sunward fan-shaped coma). Time variations are noted in the projected nucleus cross section. Results suggest significant limb-darkening effects in the relevant domains of radio waves, and that the comet's interior must be extremely cold. It is found that the thermal-infrared fluxes from the inner coma of the comet are dominated by the nucleus.

Sekanina, Z.↗

Towards a methodology for robust parameter identification

Consideration is given to the problem of estimating, from experimental data, real parameters for a model with uncertainty in the form of both additive noise and norm-bounded perturbations. Such models frequently arise in robust control theory, and a framework is introduced for the consideration of experimental data in robust control analysis problems. If the analysis tools applied include robust stability tests for real parameter variations (real mu), the framework can be used to address the problem of robust parameter identification. While the techniques discussed can quickly become computationally overwhelming when applied to physical systems and real data, the approach introduces a novel way of looking at the identification problem and may be helpful in arriving at a more tractable methodology.

Smith, Roy S.↗

Geometric and radiometric preprocessing of airborne visible/infrared imaging spectrometer (AVIRIS) data in rugged terrain for quantitative data analysis

A geocoding procedure for remotely sensed data of airborne systems in rugged terrain is affected by several factors: buffeting of the aircraft by turbulence, variations in ground speed, changes in altitude, attitude variations, and surface topography. The current investigation was carried out with an Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) scene of central Switzerland (Rigi) from NASA's Multi Aircraft Campaign (MAC) in Europe (1991). The parametric approach reconstructs for every pixel the observation geometry based on the flight line, aircraft attitude, and surface topography. To utilize the data for analysis of materials on the surface, the AVIRIS data are corrected to apparent reflectance using algorithms based on MODTRAN (moderate resolution transfer code).

Meyer, Peter↗

Preliminary analysis of dynamic stall effects on a 91-meter wind turbine rotor

Analytical investigation of dynamic stall on HAWT (horizontal-axis wind turbines) rotor loads was conducted. Dynamic stall was modeled using the Gormont approach on the MOD-2 rotor, treating the blade as a rigid body teetering about a fixed axis. Blade flapwise bending moments at station 370 were determined with and without dynamic stall for spatial variations in local wind speed due to wind shear and yaw. The predicted mean flapwise bending moments were found to be in good agreement with test results. Results obtained with and without dynamic stall showed no significant difference for the mean flapwise bending moment. The cyclic bending moments calculated with and without dynamic stall effects were substantially the same. None of the calculated cyclic loads reached the level of the cyclic loads measured on the MOD-2 using the Boeing five-minute-average technique.

Wilson, Robert E.↗

Description and Analysis of Core Samples: The Lunar Experience

Although no samples yet have been returned from a comet, extensive experience from sampling another solar system body, the Moon, does exist. While, in overall structure, composition, and physical properties the Moon bears little resemblance to what is expected for a comet, sampling the Moon has provided some basic lessons in how to do things which may be equally applicable to cometary samples. In particular, an extensive series of core samples has been taken on the Moon, and coring is the best way to sample a comet in three dimensions. Data from cores taken at 24 Apollo collection stations and 3 Luna sites have been used to provide insight into the evolution of the lunar regolith. It is now well understood that this regolith is very complex and reflects gardening (stirring of grains by micrometeorites), erosion (from impacts and solar wind sputtering), maturation (exposure on the bare lunar surface to solar winds ions and micrometeorite impacts) and comminution of coarse grains into finer grains, blanket deposition of coarse-grained layers, and other processes. All of these processes have been documented in cores. While a cometary regolith should not be expected to parallel in detail the lunar regolith, it is possible that the upper part of a cometary regolith may include textural, mineralogical, and chemical features which reflect the original accretion of the comet, including a form of gardening. Differences in relative velocities and gravitational attraction no doubt made this accretionary gardening qualitatively much different than the lunar version. Furthermore, at least some comets, depending on their orbits, have been subjected to impacts of the uppermost surface by small projectiles at some time in their history. Consequently, a more recent post-accretional gardening may have occurred. Finally, for comets which approach the sun, large scale erosion may have occurred driven by gas loss. The uppermost material of these comets may reflect some of the features of this erosional process, such as crust formation, and variations with depth might be expected. Overall, the upper few meters of a comet may be as complex in their own way as the upper few meters of the lunar regolith have proven to be, and by analogy, detailed studies of core samples containing this depth information will be needed to understand these processes and the details of the accretional history and the subsequent alteration history of comets.

McKay, David S.↗