Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Test Pilots”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Advances in Thrust-Based Emergency Control of an Airplane

Engineers at NASA's Dryden Flight Research Center have received a patent on an emergency flight-control method implemented by a propulsion-controlled aircraft (PCA) system. Utilizing the preexisting auto-throttle and engine-pressure-ratio trim controls of the airplane, the PCA system provides pitch and roll control for landing an airplane safely without using aerodynamic control surfaces that have ceased to function because of a primary-flight-control-system failure. The installation of the PCA does not entail any changes in pre-existing engine hardware or software. [Aspects of the method and system at previous stages of development were reported in Thrust-Control System for Emergency Control of an Airplane (DRC-96-07), NASA Tech Briefs, Vol. 25, No. 3 (March 2001), page 68 and Emergency Landing Using Thrust Control and Shift of Weight (DRC-96-55), NASA Tech Briefs, Vol. 26, No. 5 (May 2002), page 58.]. Aircraft flight-control systems are designed with extensive redundancy to ensure low probabilities of failure. During recent years, however, several airplanes have exhibited major flight-control-system failures, leaving engine thrust as the last mode of flight control. In some of these emergency situations, engine thrusts were successfully modulated by the pilots to maintain flight paths or pitch angles, but in other situations, lateral control was also needed. In the majority of such control-system failures, crashes resulted and over 1,200 people died. The challenge lay in creating a means of sufficient degree of thrust-modulation control to safely fly and land a stricken airplane. A thrust-modulation control system designed for this purpose was flight-tested in a PCA an MD-11 airplane. The results of the flight test showed that without any operational control surfaces, a pilot can land a crippled airplane (U.S. Patent 5,330,131). The installation of the original PCA system entailed modifications not only of the flight-control computer (FCC) of the airplane but also of each engine-control computer. Inasmuch as engine-manufacturer warranties do not apply to modified engines, the challenge became one of creating a PCA system that does not entail modifications of the engine computers.

Creech, Gray↗
DOE OSTI2023

Thermo-Hydro-Mechanical Modeling of Brine Migration in a Heated Borehole Test in Bedded Salt

Abstract This research paper focuses on the thermo-hydro-mechanical (THM) modeling of brine migration in a heated borehole test conducted as part of the ongoing Brine Availability Test in Salt (BATS) at the Waste Isolation Pilot Plant (WIPP) in New Mexico. It is a component of the international collaboration project DECOVALEX-2023 (DEvelopment of COupled models and their VALidation against EXperiments), which aims to understand the THM processes governing brine flow in heated rock salt repositories through collaborative analysis by multiple research teams. Using the TOUGH–FLAC simulator, THM simulations were performed and compared with data from the BATS phase 1a. This experiment involved two identical horizontal-borehole arrays, one heated and one serving as a control, both equipped with sensor arrays. Analysis of measurements revealed water flow rate surges during heater power transitions, with the highest jump observed during cooling. Acoustic emission activity exhibited distinct patterns in response to heater power changes, suggesting that damage to rock salt is particularly pronounced during the cooling phase. The THM simulations successfully captured these phenomena, highlighting the significance of thermal effects, brine migration, and mechanical behavior in predicting brine availability in heated and damaged rock salt. Our modeling also revealed the critical interplay between heating and cooling-induced damage and its influence on flow properties, particularly affecting brine inflow estimation. Notably, we found that cooling-induced brine inflow spikes result from increased permeability due to tensile dilatancy. These findings have important implications for the development of robust containment strategies and enhance our understanding of the complex processes involved in repository performance.

58 GEOSCIENCES↗
DOE OSTI2023

Multi-regime mixing modeling for local extinction and re-ignition in turbulent non-premixed flame by using LES/FDF method

Local extinction and re-ignition occur in turbulent non-premixed combustion when the Damköhler number is not large enough and the combustion is not fully mixing controlled. The occurrence of local extinction introduces locally extinguished flame holes followed by a premixed flame propagation toward the hole center to potentially reignite the flame. The co-existence of the non-premixed and premixed combustion regimes complicates the modeling since traditional combustion models are mostly for a single regime. In this work, we examine the effect of multi-regime mixing modeling in the transported filtered density function (FDF) method on the predictions of local extinction and reignition. Predictions of local extinction and reignition remain a challenge for the FDF method despite the progress made in the past. To account for the multi-regime combustion, two different mixing timescale models for non-premixed and premixed combustion are combined. A flame index based on the gradients of fuel and oxidizer is used to define a weighting factor to blend the two mixing timescale models. A turbulent jet non-premixed flame with substantial local extinction, the Sydney piloted jet flame L, is adopted as a test case to examine the performance of the multi-regime model in large-eddy simulation/FDF modeling. It is found that the traditional non-premixed mixing timescale model when combined with the modified Curl mixing leads to global extinction for the Sydney flame L without the presence of the premixed combustion regime. After accounting for the multi-regime combustion with proper detection of the different combustion regimes, the predictions for the flame statistics and the amount of local extinction are significantly improved. Furthermore, it suggests the need of including multi-regime combustion for the predictions of local extinction and re-ignition in turbulent non-premixed combustion configurations.

42 ENGINEERING↗
DOE OSTI2022

Experimental Investigation of Polymer-Induced Fouling of Heater Tubes in the First-Ever Polymer Flood on Alaska North Slope Part II

A polymer flood pilot has been ongoing in the Schrader Bluff viscous oil reservoir at Milne Point on the Alaska North Slope. The results from the pilot are encouraging. However, a major concern of the operator is the influence of polymer on the production system after breakthrough, especially the fouling in heat exchangers. This work applies a multiexperimental approach to study the severity of polymer-induced fouling in both dynamic and static states of produced fluids to determine safe operating conditions. Dynamic scale loop (DSL) tests were conducted to study fouling due to polymer at different skin temperatures (165–350°F) in a dynamic state of fluid flow where the fluids’ flow mimics the residence time of fluids in the heat exchanger of the field pilot. Static deposit tests were also conducted at similar skin temperatures of 165–250°F using a novel experimental apparatus designed and built in-house. It was found that at higher skin temperatures of 250–350°F, tube blocking was observed in the DSL tests, whereas the tests at 165–200°F did not show any tube blocking, even in a more extended test period. The deposit test showed that the deposit rate generally increases with skin temperature, and the presence of polymer aggravates the fouling. The copper tube performs best when the skin temperatures are 165–200°F, while the stainless steel tube performs best at a skin temperature of 250°F. These experiments also manifested the influence of the cloudpoint of the solution as the deposit rate increased significantly when the skin temperature was higher than the solution cloudpoint. The study provides a source of practical guidance to the field operations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1974

Preliminary flight tests of an oculometer

A remote sensing oculometer has been successfully operated during flight tests. This device was able to track the pilot's eye-point-of-regard (lookpoint) consistently and unobtrusively in the flight environment. The instantaneous position of the lookpoint was determined to within approximately 1 degree. Data were recorded on both analog and video tape. The video data consisted of continuous scenes of the aircraft's instrument display and a superimposed white dot (simulating the lookpoint) dwelling or moving from instrument to instrument as the pilot monitored the display information during landing approaches.

Middleton, D. B.↗
NASA NTRS1976

Display/control requirements for automated VTOL aircraft

A systematic design methodology for pilot displays in advanced commercial VTOL aircraft was developed and refined. The analyst is provided with a step-by-step procedure for conducting conceptual display/control configurations evaluations for simultaneous monitoring and control pilot tasks. The approach consists of three phases: formulation of information requirements, configuration evaluation, and system selection. Both the monitoring and control performance models are based upon the optimal control model of the human operator. Extensions to the conventional optimal control model required in the display design methodology include explicit optimization of control/monitoring attention; simultaneous monitoring and control performance predictions; and indifference threshold effects. The methodology was applied to NASA's experimental CH-47 helicopter in support of the VALT program. The CH-47 application examined the system performance of six flight conditions. Four candidate configurations are suggested for evaluation in pilot-in-the-loop simulations and eventual flight tests.

Hoffman, W. C.↗
NASA NTRS1981

HiMAT onboard flight computer system architecture and qualification

Two highly maneuverable aircraft technology (HiMAT) remotely piloted research vehicles (RPRV's) are being flight tested at NASA Dryden Flight Research Center, Edwards, California, to demonstrate and evaluate a number of technological advances applicable to future fighter aircraft. Closed-loop primary flight control is performed from a ground-based cockpit utilizing a digital computer and up/down telemetry links. A backup flight control system for emergency operation resides in one of two onboard computers. Other functions of the onboard computer system are uplink processing, downlink processing, engine control, failure detection, and redundancy management. This paper describes the architecture, functions, and flight qualification of the HiMAT onboard flight computer systems.

Myers, A. F.↗
NASA NTRS1985

Demonstration of relaxed static stability on a commercial transport

The application of relaxed static stability was studied under a program to determine ways of improving the energy efficiency in current and future transport aircraft. Pitch active control systems (PACs) were developed for application in the near term to current aircraft and in the next generation to advanced aircrft of the future. Analyses identified potential drag benefits of: (1) 2% for current transport aircraft with neutral stability; and (2) as much as 17% for next generation aircraft with high aspect ratio supercritical wings which must operate 10 to 15% statistically unstable to achieve optimum performance. Flight test evaluations of the near-term PACs were conducted to a 3% mean aerodynamic chord (MAC) negative static margin on a Lockheed L-1011 aircraft. The advanced PACs was demonstrated to a 20% MAC negative static margin on a piloted visual motion simulator at the NASA Langley Research Center. Test results for both systems showed flying qualities characteristics as good as current conventional aircraft.

Rising, J. J.↗
NASA NTRS1987

An application of artificial intelligence theory to reconfigurable flight control

Artificial intelligence techniques were used along with statistical hpyothesis testing and modern control theory, to help the pilot cope with the issues of information, knowledge, and capability in the event of a failure. An intelligent flight control system is being developed which utilizes knowledge of cause and effect relationships between all aircraft components. It will screen the information available to the pilots, supplement his knowledge, and most importantly, utilize the remaining flight capability of the aircraft following a failure. The list of failure types the control system will accommodate includes sensor failures, actuator failures, and structural failures.

Handelman, David A.↗
NASA NTRS1986

Flight evaluation of height response characteristics for the hover bob-up task and comparison with proposed criteria

The CH-47B variable-stability helicopter was used to evaluate a range of height-response configurations while performing a precision hover bob-up task. The purpose of the study was to assess the validity of results obtained in previous ground-based and in-flight simulations in the context of a precision bob-up task and to provide additional flight data for inclusion in revisions to specifications for helicopter handling qualities. Height response characteristics were implemented using explicit model-following techniques, and the resulting CH-47B dynamics were validated using time-domain and frequency-domain data-analysis methods. The tests complemented the previous investigations by providing detailed pilot comments and ratings, and performance and control-utilization data that relate exclusively to the hover bob-up task. The results are compared with those from previous investigations and with new criteria that have been proposed for handling qualities requirements for helicopters.

Hindson, W. S.↗
NASA NTRS1990

Guidance concepts for time-based flight operations

Airport congestion and the associated delays are severe in today's airspace system and are expected to increase. NASA and the FAA is investigating various methods of alleviating this problem through new technology and operational procedures. One concept for improving airspace productivity is time-based control of aircraft. Research to date has focused primarily on the development of time-based flight management systems and Air Traffic Control operational procedures. Flight operations may, however, require special onboard guidance in order to satisfy the Air Traffic Control imposed time constraints. The results are presented of a simulation study aimed at evaluating several time-based guidance concepts in terms of tracking performance, pilot workload, and subjective preference. The guidance concepts tested varied in complexity from simple digital time-error feedback to an advanced time-referenced-energy guidance scheme.

Vicroy, Dan D.↗
NASA NTRS1991

The NASA Lewis integrated propulsion and flight control simulator

A new flight simulation facility was developed at NASA-Lewis. The purpose of this flight simulator is to allow integrated propulsion control and flight control algorithm development and evaluation in real time. As a preliminary check of the simulator facility capabilities and correct integration of its components, the control design and physics models for a short take-off and vertical landing fighter aircraft model were shown, with their associated system integration and architecture, pilot vehicle interfaces, and display symbology. The initial testing and evaluation results show that this fixed based flight simulator can provide real time feedback and display of both airframe and propulsion variables for validation of integrated flight and propulsion control systems. Additionally, through the use of this flight simulator, various control design methodologies and cockpit mechanizations can be tested and evaluated in a real time environment.

Bright, Michelle M.↗
NASA NTRS1992

Cockpit weather information needs

The primary objective is to develop an advanced pilot weather interface for the flight deck and to measure its utilization and effectiveness in pilot reroute decision processes, weather situation awareness, and weather monitoring. Identical graphical weather displays for the dispatcher, air traffic control (ATC), and pilot crew should also enhance the dialogue capabilities for reroute decisions. By utilizing a broadcast data link for surface observations, forecasts, radar summaries, lightning strikes, and weather alerts, onboard weather computing facilities construct graphical displays, historical weather displays, color textual displays, and other tools to assist the pilot crew. Since the weather data is continually being received and stored by the airborne system, the pilot crew has instantaneous access to the latest information. This information is color coded to distinguish degrees of category for surface observations, ceiling and visibilities, and ground radar summaries. Automatic weather monitoring and pilot crew alerting is accomplished by the airborne computing facilities. When a new weather information is received, the displays are instantaneously changed to reflect the new information. Also, when a new surface or special observation for the intended destination is received, the pilot crew is informed so that information can be studied at the pilot's discretion. The pilot crew is also immediately alerted when a severe weather notice, AIRMET or SIGMET, is received. The cockpit weather display shares a multicolor eight inch cathode ray tube and overlaid touch panel with a pilot crew data link interface. Touch sensitive buttons and areas are used for pilot selection of graphical and data link displays. Time critical ATC messages are presented in a small window that overlays other displays so that immediate pilot alerting and action can be taken. Predeparture and reroute clearances are displayed on the graphical weather system so pilot review of weather along the route can be accomplished prior to pilot acceptance of the clearance. An ongoing multiphase test series is planned for testing and modifying the graphical weather system. Preliminary data shows that the nine test subjects considered the graphical presentation to be much better than their current weather information source for situation awareness, flight safety, and reroute decision making.

Scanlon, Charles H.↗
NASA NTRS1991

An evaluation of strategic behaviors in a high fidelity simulated flight task - Comparing primary performance to a figure of merit

The usual method of evaluating flight performance during a simulation is to collect as many primary performance measurements as possible. Then analyze all the measurements to find one sensitive to the manipulations imposed on the pilot during the scenario. Although this method can be useful, it is usually unreliable from one study to another. A simulation was conducted to test an integrated figure of merit (FOM) constructed using a standardized procedure. Pilots flew two full-mission scenarios in an instrument trainer with three degrees of motion freedom. The primary performance measurements selected assessed the pilot's performance in accuracy, smoothness, and activity. The results suggest that the integrated FOMs performed comparably to the primary performance measurements in determining which flight imposed the higher demands on the pilot. The standardized construction process allow adjustments to the FOM, so it can be used in different applications.

Bortolussi, Michael R.↗