SEARCH · Engineering Papers

Results for “TWIST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Absorption of acoustic waves by sunspots. II - Resonance absorption in axisymmetric fibril models

Analytical calculations of acoustic waves scattered by sunspots which concentrate on the absorption at the magnetohydrodynamic Alfven resonance are extended to the case of a flux-tube embedded in a uniform atmosphere. The model is based on a flux-tubes of varying radius that are highly structured, translationally invariant, and axisymmetric. The absorbed fractional energy is determined for different flux-densities and subphotospheric locations with attention given to the effects of twist. When the flux is highly concentrated into annuli efficient absorption is possible even when the mean magnetic flux density is low. The model demonstrates low absorption at low azimuthal orders even in the presence of twist which generally increases the range of wave numbers over which efficient absorption can occur. Resonance absorption is concluded to be an efficient mechanism in monolithic sunspots, fibril sunspots, and plage fields.

Rosenthal, C. S.↗

NASA NTRS1991

Effect of damage on elastically tailored composite laminates

A variationally consistent theory is derived in order to predict the response of anisotropic thin-walled closed sections subjected to axial load, torsion and bending. The theory is valid for arbitrary cross-sections made of laminated composite materials with variable thickness and stiffness. Closed form expressions for the stiffness coefficients are provided as integrals in terms of lay-ups parameters and cross-sectional geometry. A comparison of stiffness coefficients and response with finite element predictions and a closed form solution is performed. The theory is applied to the investigation of the effect of damage on the extension-twist coupling in a thin-walled closed section beam. The damage is simulated as a progressive ply-by-ply failure. Results show that damage can have a significant effect on the extension-twist coupling.

Armanios, Erian↗

NASA NTRS1951

Empirical relation between induced velocity, thrust, and rate of descent of a helicopter rotor as determined by wind-tunnel tests on four model rotors

The empirical relation between the induced velocity, thrust, and rate of vertical descent of a helicopter rotor was calculated from wind tunnel force tests on four model rotors by the application of blade-element theory to the measured values of the thrust, torque, blade angle, and equivalent free-stream rate of descent. The model tests covered the useful range of C(sub t)/sigma(sub e) (where C(sub t) is the thrust coefficient and sigma(sub e) is the effective solidity) and the range of vertical descent from hovering to descent velocities slightly greater than those for autorotation. The three bladed models, each of which had an effective solidity of 0.05 and NACA 0015 blade airfoil sections, were as follows: (1) constant-chord, untwisted blades of 3-ft radius; (2) untwisted blades of 3-ft radius having a 3/1 taper; (3) constant-chord blades of 3-ft radius having a linear twist of 12 degrees (washout) from axis of rotation to tip; and (4) constant-chord, untwisted blades of 2-ft radius. Because of the incorporation of a correction for blade dynamic twist and the use of a method of measuring the approximate equivalent free-stream velocity, it is believed that the data obtained from this program are more applicable to free-flight calculations than the data from previous model tests.

Castles, Walter, Jr.↗

NASA NTRS1991

The 3-D description of vertical current sheets with application to solar flares

Following a brief review of the processes which have been suggested for explaining the occurrence of solar flares we suggest a new scenario which builds on the achievements of the previous suggestion that the current sheets, which develop naturally in 3-D cases with gravity from impacting independent magnetic structures (i.e., approaching current systems), do not consist of horizontal currents but are instead predominantly vertical current systems. This suggestion is based on the fact that as the subphotospheric sources of the magnetic field displace the upper photosphere and lower chromosphere regions, where plasma beta is near unity, will experience predominantly horizontal mass motions which will lead to a distorted 3-D configurations of the magnetic field having stored free energy. In our scenario, a vertically flowing current sheet separates the plasma regions associated with either of the subphotospheric sources. This reflects the balanced tension of the two stressed fields which twist around each other. This leads naturally to a metastable or unstable situation as the twisted field emerges into a low beta region where vertical motions are not inhibited by gravity. In our flare scenario the impulsive energy release occurs, initially, not by reconnection but mainly by the rapid change of the magnetic field which has become unstable. During the impulsive phase the field lines contort in such way as to realign the electric current sheet into a minimum energy horizontal flow. This contortion produces very large electric fields which will accelerate particles. As the current evolves to a horizontal configuration the magnetic field expands vertically, which can be accompanied by eruptions of material. The instability of a horizontal current is well known and causes the magnetic field to undergo a rapid outward expansion. In our scenario, fast reconnection is not necessary to trigger the flare, however, slow reconnection would occur continuously in the current layer at the locations of potential flaring. During the initial rearrangement of the field strong plasma turbulence develops. Following the impulsive phase, the final current sheet will experience faster reconnection which we believe responsible for the gradual phase of the flare. The reconnection will dissipate part of the current and will produce sustained and extended heating in the flare region and in the postflare loops.

Fontenla, Juan M.↗

NASA NTRS1992

The use of cross-section warping functions in composite rotor blade analysis

During the contracted period, our research was concentrated into three areas. The first was the development of an accurate and a computationally efficient method for predicting the cross-section warping functions in an arbitrary cross-section composed of isotropic and/or anisotropic materials. The second area of research was the development of a general higher-order one-dimensional theory for anisotropic beams. The third area of research was the development of an analytical model for assessing the extension-bend-twist coupling behavior of nonhomogeneous anisotropic beams with initial twist. In the remaining six chapters of this report, the three different research areas and associated sub-research areas are covered independently including separate introductions, theoretical developments, numerical results, and references.

Kosmatka, J. B.↗

NASA NTRS1993

Evaluation of MARC for the analysis of rotating composite blades

The suitability of the MARC code for the analysis of rotating composite blades was evaluated using a four-task process. A nonlinear displacement analysis and subsequent eigenvalue analysis were performed on a rotating spring mass system to ensure that displacement-dependent centrifugal forces were accounted for in the eigenvalue analysis. Normal modes analyses were conducted on isotropic plates with various degrees of twist to evaluate MARC's ability to handle blade twist. Normal modes analyses were conducted on flat composite plates to validate the newly developed coupled COBSTRAN-MARC methodology. Finally, normal modes analyses were conducted on four composite propfan blades that were designed, analyzed, and fabricated at NASA Lewis Research Center. Results were compared with experimental data. The research documented herein presents MARC as a viable tool for the analysis of rotating composite blades.

Bartos, Karen F.↗

NASA NTRS1993

Aeroservoelastic DAP missile fin development

The development of an active aeroservoelastic missile fin using directionally attached piezoelectric (DAP) actuator elements is detailed. Several different types of actuator elements are examined, including piezoelectric polymers, piezoelectric fiber composites, and conventionally attached piezoelectric (CAP) and DAP elements. These actuator elements are bonded to the substrate of a torque plate. The root of the torque plate is attached to a fuselage hard point or folding pivot. The tip of the plate is bonded to an aerodynamic shell which undergoes a pitch change as the plate twists. The design procedures used on the plate are discussed. A comparison of the various actuator element shows that DAP elements provide the highest deflections with the highest torsional stiffness. A torque plate was constructed from 0.2032 mm thick DAP elements bonded to a 0.127 mm thick AISI 1010 steel substrate. The torque plate produced static twist deflections in excess of +/- 3 deg. An aerodynamic shell with a modified NACA 0012 profile was added to the torque plate. This fin was tested in a wind tunnel at speeds up to 50 ms/sec. The static deflection of the fin was predicted to within 6 percent of the experimental data.

Barrett, Ron↗

NASA NTRS1993

Long-term containment of energetic particles in coronal loops

Recent observation from the Compton Gamma-Ray Observatory shows that gamma-ray emission after a solar flare can last for as long as 8 hours. There is also evidence that electrons and protons are accelerated only during the impulsive phase of the flare and are subsequently mirror trapped in coronal magnetic loops. This poses the following dilemma: if the magnetic field lines in the loop are simple plane arches, the protons will drift across the cross section of the loop in seconds to minutes, rather than hours. To solve the dilemma, we use guiding center theory to show that long-term containment of energetic protons in a coronal loop is possible if magnetic field lines have enough twist. We also find that in the trapped region of the loop, the twist angle of field lines between the mirror points of a bounce orbit is approximately 2 pi.

Lau, Yun-Tung↗

NASA NTRS1933

Mercerization of Cotton for Strength with Special Reference to Aircraft Cloth

The object of the present investigation was to determine the conditions for mercerizing cotton yarn to obtain the maximum strength for a given weight. Apparatus for controlling the variables was built and yarns were mercerized with it under systematically varied conditions of tension, time, temperature, and concentration of caustic soda. The strongest conclusion to be drawn from this work is that the strongest mercerized yarn of a given count from a given quality of cotton is obtained under the following conditions: 1. use of low-twist yarn obtained with twist multipliers from 2.2 to 3; 2. thorough pretreatment of the yarn to remove all extraneous materials; 3. mercerization at a temperature of 0 C or lower; 4. use of sufficient tension during mercerization to prevent the yarn from contracting more than 3 percent. 5. Use of caustic solution having a concentration of 10 percent or higher; 6. the time of mercerization to be 5 minutes. The resulting yarn should be 40 to 100 percent stronger than the original yarn of the same weight.

Wilkie, J B↗

NASA NTRS1939

Experimental Study of Deformation and of Effective Width in Axially Loaded Sheet-stringer Panels

The deformation of two sheet-stringer panels subjected to end compression under carefully controlled end conditions was measured at a number of points and at a number of loads, most of which were above the load at which the sheet had begun to buckle. The two panels were identical except for the sheet, which was 0.70-inch 24st alclad for specimen 1 and 0.025-inch 24st aluminum alloy for specimen 6. A technique was developed for attaching Tuckerman optical strain gauges to the sheet without disturbing the strain distribution in the sheet by the method of attachment. This technique was used to explore the strain distribution in the sheet at various loads. The twisting and the bending of the stringers was measured by means of pointers attached to the stringers. The shape of the buckles in the sheet of specimen 6 was recorded at two loads by means of plaster casts. The sheet and the stringer loads at failure are compared with the corresponding loads for five similar panels tested at the Navy Model Basin. A detailed comparison is made between the measured deformation of the buckled sheet and the deformation calculated from approximate theories for the deformation in a rectangular sheet with freely supported edges buckling under end compression advanced by Timoshenko, Frankland, and Marguerre. The measured effective width for the specimens is compared with the effective width given by nine different relations for effective width as a function of the edge stress divided by the buckling stress of the sheet. The analysis of the measured stringer deformation is confined to an application of Southwell's method of plotting deformation against deformation over load. It was concluded that the stringer failure in both specimens were due to an instability in which the stringer was simultaneously twisted and bent as a column.

FORMULAS - BUCKLING - KARMAN↗

NASA NTRS1940

The frequencies of cantilever wings in beam and torsional vibrations

Methods are described for calculating the period and frequency of vibration of cantilever wings and similar structures in which the weight and moment of inertia vary along the span. Both the beam and torsional frequencies may be calculated by these methods. The procedure is illustrated by examples. It is shown that a surprisingly close approximation to the beam frequency may be obtained by a very brief calculation in which the curvature of the wing in vibration is assumed to be constant. A somewhat longer computation permits taking account of the true curvature of the beam by a series of successive approximations which are shown to be strongly convergent. Analogous methods are applied to calculations of the torsional frequency. For the first approximation it is assumed that the angle of twist varies linearly alone the semispan. True variation of the twist is computed by successive approximations which are strongly convergent, as in the case of beam vibrations.

Burgess, C P↗

NASA NTRS1951

Empirical Relation Between Induced Velocity, Thrust, and Rate of Descent of a Helicopter Rotor as Determined by Wind-tunnel Tests on Four Model Rotors

Castles, Walter, Jr↗

NASA NTRS1956

Charts for estimating the hovering endurance of a helicopter

As a means of comparing the performance capabilities of various helicopter propulsion systems, charts have been presented for estimating the hovering endurance of a helicopter in the form of a hovering-endurance parameter as a function of the ratio of total fuel load to helicopter initial weight for a range of initial thrust coefficients from 0.002 to 0.012 and for values of rotor mean lift coefficient from 0.24 to .072. The charts were presented for a helicopter having rotor blades with ideal twist. However, corrections may be applied to the hovering endurance to account for other combinations of twist and taper. The effects of stall and compressibility have been neglected.

HELICOPTERS↗

NASA NTRS1951

Experimental investigation of an 0.8 hub-tip radius-ratio,nontwisted-rotor-blade turbine

An experimental investigation of a 0.8 hub-tip radius ratio, nontwisted-rotor-blade turbine designed for a stagnation-pressure ratio of 2.5 and an equivalent mean blade speed of 643 feet per second was made in a cold-air turbine with (a) nontwisted stator blades, and (b) twisted stator blades designed to maintain zero rotor-inlet incidence angles. Turbine efficiencies of the order of 0.85 at the design point were obtained with a nontwisted-rotor-blade turbine with a hub-tip radius ratio of 0.80. The turbine with the twisted stator blades gave higher efficiencies at the design point (of the order of 1.5 percentage points) than the turbine with the nontwisted stator blades.

TURBINES - AXIAL FLOW↗

NASA NTRS1948

Theoretical symmetric span loading at subsonic speeds for wings having arbitrary plan form

A method is shown by which the symmetric span loading for a certain class of wings can be simply found. The geometry of these wings is limited only to the extent that they must have symmetry about the root chord, must have a straight quarter-chord line over the semispan, and must have no discontinuities in twist. A procedure is shown for finding the lift-curve slope, pitching moment, center of lift, and induced drag from the span load distribution. A method of accounting for the effects of Mach number and for changes in section lift-curve slope is also given. Charts are presented which give directly the characteristics of many wings. Other charts are presented which reduce the problem of finding the symmetric loading on all wings falling within the prescribed limits to the solution of not more than four simultaneous equations. The loadings and wing characteristics predicted by the theory are compared to those given by other theories and by experiment. It is concluded that the results given by the subject theory are satisfactory. The theory is applied to a number of wings to exhibit the effects of such variables as sweep, aspect ratio, taper, and twist. The results are compared and conclusions drawn as to the relative effects of these variables.

Deyoung, John↗

NASA NTRS1941

Observations of the Effect of Wing Appendages and Flaps on the Spread of Separation of Flow over the Wing

The spread of the separation of flow on three tapered wings insymmetrical and unsymmetrical flow was observed with silk tufts. By equal thickness and chord distribution the wings manifested a different form of lifting line. The principal result of the study was that the wings alone first disclosed complete breakdown of the flow at the tips, even the one with twist, but that after adding fuselage and engine nacelles, the twisted wing broke down completely first in the wing center. The observed boundary layer motions transverse to the main flow direction were briefly explored as to their possible influence on the spread of the separation. On top of that certain disclosures were afforded in which the transverse motions observed in the boundary layer became perceptible even above the boundary layer.

Hartwig, G↗

NASA NTRS1993

A four-axis hand controller for helicopter flight control

A proof-of-concept hand controller for controlling lateral and longitudinal cyclic pitch, collective pitch and tail rotor thrust was developed. The purpose of the work was to address problems of operator fatigue, poor proprioceptive feedback and cross-coupling of axes associated with many four-axis controller designs. The present design is an attempt to reduce cross-coupling to a level that can be controlled with breakout force, rather than to eliminate it entirely. The cascaded design placed lateral and longitudinal cyclic in their normal configuration. Tail rotor thrust was placed atop the cyclic controller. A left/right twisting motion with the wrist made the control input. The axis of rotation was canted outboard (clockwise) to minimize cross-coupling with the cyclic pitch axis. The collective control was a twist grip, like a motorcycle throttle. Measurement of the amount of cross-coupling involved in pure, single-axis inputs showed cross coupling under 10 percent of full deflection for all axes. This small amount of cross-coupling could be further reduced with better damping and force gradient control. Fatigue was not found to be a problem, and proprioceptive feedback was adequate for all flight tasks executed.

Demaio, Joe↗

NASA NTRS1993

A typical pointed observation in IRAS designed to fit into a 15 minute window

A typical pointed observation in the Infrared Astronomical Satellite (IRAS) was designed to fit into a 15 minute window. Observing constraints, however, did not always permit targets from the scientific program to be observed on exactly 15 minute centers and a few months into the mission it was realized that the automatic scheduling program left times when no observations were being made. In order to use this potentially wasted observing time, a mode of pointed observations, the 'filler' mode, with shorter observation duration was initiated. Locations were picked on an arbitrary grid, spaced relatively uniformly in ecliptic coordinates, and the telescope was pointed to one of these sites whenever a gap potentially occurred. One of us (GXN) was the coordinator of this effort (the FL sub-group). There are a total of 22 FL fields, 13 of which have more than 50 component observations. These 13 fields cover about 30 square degrees. It was proposed to concentrate on one filler field, FL29, a field with 53 coverages which thus had among the deepest coverage of those observed in this mode. This field was also observed extensively at various non-infrared wavelengths by a variety of techniques. Because the IRAS observations of FL29 were made at the limits of the survey sensitivity and at different twist angles it was necessary to make significant technical advances in the methods used in the processing and analyzing the data. In particular, if normal IRAS coaddition procedures were used, the noise resulting from coaddition of the multiple frames did not decrease in the manner expected once significantly different twist angles were included in the coaddition. The technical effort needed to reduce the observations of FL29 was completed and now the noise behavior is understood and well behaved. The reduction of the field FL29 observations is done.

Neugebauer, G.↗