SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Cadmium sulfide-thin film large area photovoltaic solar energy converter - plastic substrate cell fabrication and stability testing under various conditions of temperature and humidity
A modelling technique is described which is used to explore three dimensional (3D) image irradiance distributions formed by high numerical aperture (NA is greater than 0.5) lenses in homogeneous, linear films. This work uses a 3D modelling approach that is based on a plane-wave decomposition in the exit pupil. Each plane wave component is weighted by factors due to polarization, aberration, and input amplitude and phase terms. This is combined with a modified thin-film matrix technique to derive the total field amplitude at each point in a film by a coherent vector sum over all plane waves. Then the total irradiance is calculated. The model is used to show how asymmetries present in the polarized image change with the influence of a thin film through varying degrees of focus.
A 10GHz microwave reflectometer was developed to measure the mobility-lifetime product in thin film semiconductors. Development focused on perovskite films (an emerging photovoltaic material) as well as CdTe (an established photovoltaic material).
Hybrid organic−inorganic metal halide perovskites (MHPs) are promising semiconductors for photovoltaics and optoelectronics, but their commercial viability is limited by instability, particularly strain induced by mismatch in coefficients of thermal expansion (CTE) between the perovskite film and substrate. Here, we investigate strain development and relaxation in MHP thin films using in situ bending and Grazing Incidence Wide-Angle X-ray Scattering (GIWAXS). We quantify the film− substrate interfacial mechanical coupling and identify interfacial slippage beyond a critical strain (∼0.4%), with Br-2PACz exhibiting comparatively stronger interfacial mechanical coupling among common interface modifiers. Time-resolved GIWAXS reveals reversible macrostrain during thermal cycling driven by CTE mismatch. Leveraging this behavior, we introduce a prestrain process that induces persistent compressive strain after cooling, with partial relaxation over time. These results provide insight into interfacial mechanical coupling and strain dynamics, offering a framework for strain engineering in perovskite devices.
The work directed towards developing methods of increasing the strength of thin boron films is reported. The program was divided into two main parts. The first involved the improvement of methods for the measurement of the strength of thin films. The second was a study of the effect of condensation of deposition temperature on the strength of the films. Techniques were developed for depositing boron films onto both sides of thin titanium and tantalum foils. Small dogbone sections of boron were made by masking. Strain gauges were then mounted on these to measure failure strains when the films were loaded in tension. Test results were consistent with those obtained by flexure tests. The most important flaws in the boron films appeared to have been generated by either small globules of boron ejected from the melt or small particles (possibly boron dust) on the substrate prior to deposition.
Aging of energetic materials may change performance and affect their safety and reliability, but the relationship between microstructure changes induced by aging and consequent performance changes has not been fully established. This work presents results of phase-field method simulations used to model microstructure evolution of vapor-deposited pentaerythritol tetranitrate (PETN) thin films. Simulated aging is shown to induce grain coarsening and substantial changes of the configuration of porosity in the film: Specifically, we show that porosity tends to concentrate in large pores to a greater degree in aged films, a state that is arrived at by closure or consolidation of small pores. To evaluate the performance of the as-deposited and aged films, we perform two-dimensional hydrocode flyer-film impact simulations that incorporate the phase-field output microstructures directly, permitting us to connect features therein to changes in reactivity, a key metric of energy output for shock initiation. The results demonstrate that declining sensitivity obtained for the simulated aged films can be correlated with the loss of fine-structured pores relatively early in the aging process, while long-term microstructure evolution that gradually alters the shape of large, branching pores is less impactful. Finally, we discuss commonalities and discrepancies between our simulation results and high-throughput initiation experiments on shock initiation of aged PETN thin films.
The project was aimed at developing and demonstrating an advanced solid-oxide fuel cell (SOFC) technology to cost-effectively and reliably generate electricity directly from hydrocarbon fuels (e.g., natural gas and coal-derived syngas) for distributed and central generation applications. The studied technology was built on a planar, porous metal-supported SOFC (MS-SOFC) with a unique thin-film structure having its anode intimately supported on a metal substrate. The porous metal support with graded porosity was fabricated from a low-cost scalable phase-inversion tape casting method. Anode, thin-film electrolyte, and cathode were sequentially deposited on the porous metal substrate using atmospheric plasma spray (APS). In this study, it was shown that the composition of the casting slurry could significantly influence the morphology of the metal support fabricated using the phase-inversion tape-casting method. Increasing the solid loading in the slurry favored the formation and growth of finger-like pores to a point, but the presence of excessive solid loading increased the viscosity of the casting slurry, restraining the growth of finger-like pores. With the increase in the amount of the binder polyethersulfone (PESf) in the slurry, well grown finger-like pores and a thin sponge-like layer were formed. Since the parameters of the APS process have a significant effect on the microstructure of coatings, which in turn affects or determines the SOFC cell performance, a series of metal-supported solid oxide fuel cells with a four-layer cell configuration of 430L/Ni-ScSZ/ScSZ/LSCF have been fabricated by a combination of phase inversion tape casting and APS techniques. Electrochemical testing of the cells fabricated from different deposition APS conditions revealed significant differences in cell performance.
Vacuum deposition and mechanical properties of magnetic thin films of ferrite-borate mixtures
Non-volatile memory device structures such as ferroelectric random-access memory and ferroelectric tunnel junctions employ switchable spontaneous polarization to hold binary states. These devices can potentially benefit from the imposition of spontaneous internal biases and their resulting effect on the polarization properties of the ferroelectric (or field-induced ferroelectric/ antiferroelectric) layer. While HfO 2 -based thin films are ideal candidates for implementation into these devices due to their scalability and silicon compatibility, the phase purity of these oxides is sensitive to the selection of electrode material, preventing incorporation of asymmetric electrode layers into such structures. Within this work, electrode replacement following post-metallization anneal processing is introduced as a route to achieve ferroelectric and field-induced ferroelectric Hf x Zr 1–x O 2 (HZO) thin films with electrode-independent phase constitutions. The effects of this process and the corresponding internal biases imposed across the HZO layers due to asymmetric work functions are investigated. It is shown that internal biases vary in magnitude in accordance with prediction based on the work functions of the replaced electrode layers and affect remanent polarization magnitudes. Accordingly, electrode replacement presents a processing route that can readily produce HZO films with spontaneous internal biases and electrode- independent phase constitutions, facilitating implementation of these ferroelectrics into the next generation device structures.
The Bi-Ni binary system has been of interest due to possible unconventional superconductivity aroused therein, such as time-reversal symmetry breaking in Bi/Ni bilayers or the coexistence of superconductivity and ferromagnetism in Bi 3 Ni crystals. While Ni acts as a ferromagnetic element in such systems, the role of the strong spin-orbit coupling element Bi in superconductivity has remained unexplored. In this work, we systematically studied the effects of Bi stoichiometry on the superconductivity of Bi x Ni 1–x thin films (x ≈ 0.5–0.9) fabricated via a composition-spread approach. Here, the superconducting phase map of Bi x Ni 1–x thin films exhibited a superconducting composition region attributable to the intermetallic Bi 3 Ni phase with different amounts of excess Bi, revealed by synchrotron x-ray diffraction analysis. Interestingly, the mixed-phase region with Bi 3 Ni and Bi showed unusual increases in the superconducting transition temperature and residual resistance ratio as more Bi impurities were included, with the maximum T c (=4.2K) observed at x ≈ 0.79. A correlation analysis of structural, electrical, and magneto-transport characteristics across the composition variation revealed that the unusual superconducting “dome” is due to two competing roles of Bi: impurity scattering and carrier doping. We found that the carrier doping effect is dominant in the mild doping regime (0.74 ≤ x ≤ 0.79), while impurity scattering becomes more pronounced at larger Bi stoichiometry.
Multiferroic BiFeO$_3$ (BFO) shows several phonon modes at infrared (IR) to THz energies, which are expected to carry information on any sample property coupled to crystal lattice vibrations. While macroscopic IR studies of BFO are often limited by single-crystal size, scattering-type scanning near-field optical microscopy (s-SNOM) allows for IR thin film spectroscopy of nanoscopic probing volumes with negligible direct substrate contribution to the optical signal. In fact, polaritons such as phonon polaritons of BFO introduce a resonant tip–sample coupling in s-SNOM, leading to both stronger signals and enhanced sensitivity to local material properties. Here in this paper, we explore the near-field response of BFO thin films at three consecutive resonances (centered around 5 THz, 13 THz, and 16 THz), by combining s-SNOM with a free-electron laser. We study the dependence of these near-field resonances on both the wavelength and tip–sample distance. Enabled by the broad spectral range of the measurement, we probe phonon modes connected to the predominant motion of either the bismuth or oxygen ions. Therefore, we propose s-SNOM at multiple near-field resonances as a versatile and very sensitive tool for the simultaneous investigation of various sample properties.
This paper talks about solid state (sup 13)C MAS NMR investigations of amorphous carbon thin films.
Donor–acceptor (D–A) type semiconducting polymers have shown great potential for the application of deformable and stretchable electronics in recent decades. However, due to their heterogeneous structure with rigid backbones and long solubilizing side chains, the fundamental understanding of their molecular picture upon mechanical deformation still lacks investigation. Here, the molecular orientation of diketopyrrolopyrrole (DPP)-based D–A polymer thin films is probed under tensile deformation via both experimental measurements and molecular modeling. The detailed morphological analysis demonstrates highly aligned polymer crystallites upon deformation, while the degree of backbone alignment is limited within the crystalline domain. Besides, the aromatic ring on polymer backbones rotates parallel to the strain direction despite the relatively low overall chain anisotropy. Additionally, the effect of side-chain length on the DPP chain alignment is observed to be less noticeable. These observations are distinct from traditional linear-chain semicrystalline polymers like polyethylene due to distinct characteristics of backbone/side-chain combination and the crystallographic characteristics in DPP polymers. Furthermore, a stable and isotropic charge carrier mobility is obtained from fabricated organic field-effect transistors. This study deconvolutes the alignment of different components within the thin-film microstructure and highlights that crystallite rotation and chain slippage are the primary deformation mechanisms for semiconducting polymers.
Second-harmonic generation (SHG) extensively employs periodically poled nonlinear crystals through forward quasi-phase-matching to achieve efficient frequency conversion. As poling periods approach sub-micrometers, backward quasi-phase-matching has also been demonstrated, albeit by utilizing pulsed laser drives. The realization of symmetric second-harmonic generation, characterized by counterpropagating pumps, however, has remained elusive despite theoretical predictions. The main challenge lies in achieving strong nonlinear coupling with the poling period below half the wavelength of the second-harmonic light. The recent emergence of high-quality ferroelectric lithium niobate thin films provides an opportunity for achieving precise domain control at submicron dimensions. In this paper, we demonstrate reliable control of ferroelectric domains in a thin film lithium niobate waveguide with a poling period down to 370 nm, thereby realizing highly efficient continuous-wave pumped symmetric SHG. This demonstration not only validates the feasibility of achieving subwavelength periodic poling on waveguides but could also enable submicron ferrolectric domain structures to be leveraged in integrated photonics and nonlinear optics research.
Here, we used diffusive gradients in thin films (DGT) to measure potentially bioavailable metals in coastal plain streams in the southeastern USA that exhibited strong to moderate blackwater characteristics. Metals were partitioned into particulate metals, DGT-inert metals (i.e., colloidal and refractory organic complexes not accumulated by DGT), and DGT-labile metals (i.e., free metal ions, small inorganic complexes, and labile organic complexes). We also examined the influence of different DGT deployment times using data collected from the field and a follow-up laboratory study. The DGT-measured fraction of dissolved metals in the streams was 15% for Cd, 21% for Zn, 33% for Cu, 37% for Pb, and 98% for Mn. Metals bound to particulates predominated only for Pb. Most of the Cd, Pb, Zn, and Cu were associated with colloids, refractory organic complexes, or particles. Relatively small amounts were in free ion or labile complexes likely to be bioavailable through respiratory surfaces. Modeled concentrations of free and inorganically bound Cu and Pb were lower than the DGT fraction indicating that DGT accumulated some organically bound Cu and Pb that might not have been bioavailable. DGT-exposure times in excess of 5 days may have contributed to the accumulation of partly labile organic–metal complexes and were associated with substantial biofouling that caused metal uptake by DGT to depart from linearity.
The composition of pulsed-laser-deposited Y-Ba-Cu-O and Ba-K-Bi-O thin films is shown to be strongly affected by target conditioning, gas pressure, and target-substrate distance.
Thin-film material libraries in the ternary and quaternary metal oxide systems Fe–V–O, Cu–V–O, and Cu–Fe–V–O were synthesized using combinatorial reactive co-sputtering with subsequent annealing in air. Their compositional, structural, and functional properties were assessed using high-throughput characterization methods. Prior to the investigation of the quaternary system Cu–Fe–V–O, the compositions (Fe 61 V 39 )O x and (Cu 52 V 48 )O x with promising photoactivity were identified from their ternary subsystems Fe–V–O and Cu–V–O, respectively. Two Cu–Fe–V–O material libraries with (Cu 29-72 Fe 4-27 V 22-57 )O x and (Cu 11-55 Fe 27-73 V 12-34 )O x composition spread were investigated. Seven mixed ternary and quaternary phase regions were identified: I (α-Cu 3 FeV 6 O 26 /FeVO 4 ), II (Cu 5 V 2 O 10 /FeVO 4 /α-Cu 3 Fe 4 V 6 O 26 ), III (Cu 5 V 2 O 10 ), IV (Cu 5 V 2 O 10 /FeVO 4 , V (FeVO 4 /γ-Cu 2 V 2 O 7 /α-Cu 3 Fe 4 V 6 O 26 ), VI (β-Cu 2 V 2 O 7 /α-Cu 3 Fe 4 V 6 O 26 /FeVO 4 ), and VII (β-Cu 3 Fe 4 V 6 O 26 /FeVO 4 ). Furthermore, in the investigated composition range, two photoactive regions, (Cu 53 Fe 7 V 40 )O x and (Cu 45 Fe 21 V 34 )O x , were identified, exhibiting 103 μ A/cm 2 and 108 μ A/cm 2 photocurrent density for the oxygen evolution reaction at 1.63 V vs reversible hydrogen electrode, respectively. The highest photoactive region (Cu 45 Fe 21 V 34 )O x comprises the dominant α-Cu 3 Fe 4 V 6 O 24 phase and minor FeVO 4 phase. This photoactive region corresponds to having an indirect bandgap of 1.87 eV and a direct bandgap of 2.58 eV with an incident photon-to-current efficiency of 30% at a wavelength of 310 nm.
2D/3D perovskite heterostructures have emerged as a promising material composition to reduce nonradiative recombination in perovskite-based LEDs and solar cells. Such heterostructures can be created by a surface treatment with large organic cations, for example, n-butylammonium bromide (BABr). To understand the impact of the BABr surface treatment on the double-cation (Cs 0.17 FA 0.83 Pb(I 0.6 Br 0.4 ) 3 ) (FA = formamidinium) perovskite thin film and further optimize the corresponding structures, an in-depth understanding of the chemical and electronic properties of the involved surfaces, interfaces, and bulk is required. We study the impact of the BABr treatment with a combination of surface-sensitive X-ray photoelectron spectroscopy and bulk-sensitive resonant inelastic soft X-ray scattering (RIXS). A quantitative analysis of the BABr-treated perovskite thin film shows a modified chemical perovskite surface environment of carbon, nitrogen, bromine, iodine, and lead, indicating that the treatment leads to a perovskite surface with a modified composition and bonding structure. With K-edge RIXS, the local environment at the nitrogen and carbon atoms is probed, allowing us to identify the presence of BABr in the perovskite bulk albeit with a modified bonding environment. This, in turn, identifies a "hidden parameter" for the optimization of the BABr treatment and overall performance of 2D/3D perovskite solar cell absorbers.