Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar Cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Materials That Enhance Efficiency and Radiation Resistance of Solar Cells

A thin layer (approximately 10 microns) of a novel "transparent" fluorescent material is applied to existing solar cells or modules to effectively block and convert UV light, or other lower solar response waveband of solar radiation, to visible or IR light that can be more efficiently used by solar cells for additional photocurrent. Meanwhile, the layer of fluorescent coating material remains fully "transparent" to the visible and IR waveband of solar radiation, resulting in a net gain of solar cell efficiency. This innovation alters the effective solar spectral power distribution to which an existing cell gets exposed, and matches the maximum photovoltaic (PV) response of existing cells. By shifting a low PV response waveband (e.g., UV) of solar radiation to a high PV response waveband (e.g. Vis-Near IR) with novel fluorescent materials that are transparent to other solar-cell sensitive wavebands, electrical output from solar cells will be enhanced. This approach enhances the efficiency of solar cells by converting UV and high-energy particles in space that would otherwise be wasted to visible/IR light. This innovation is a generic technique that can be readily implemented to significantly increase efficiencies of both space and terrestrial solar cells, without incurring much cost, thus bringing a broad base of economical, social, and environmental benefits. The key to this approach is that the "fluorescent" material must be very efficient, and cannot block or attenuate the "desirable" and unconverted" waveband of solar radiation (e.g. Vis-NIR) from reaching the cells. Some nano-phosphors and novel organometallic complex materials have been identified that enhance the energy efficiency on some state-of-the-art commercial silicon and thin-film-based solar cells by over 6%.

Sun, Xiadong↗

Space Qualification Test of a-Silicon Solar Cell Modules

The basic requirement of solar cell modules for space applications are generally described in MIL-S-83576 for the specific needs of the USAF. However, the specifications of solar cells intended for use on space terrestrial applications are not well defined. Therefore this qualification test effort was concentrated on critical areas specific to the microseismometer probe which is intended to be included in the Mars microprobe programs.

Silicon Solar Cells↗

Synergistically Enhanced Performance of Ultrathin Nanostructured Silicon Solar Cells Embedded in Plasmonically Assisted, Multispectral Luminescent Waveguides

Ultrathin silicon solar cells fabricated by anisotropic wet chemical etching of single-crystalline wafer materials represent an attractive materials platform that could provide many advantages for realizing high-performance, low-cost photovoltaics. However, their intrinsically limited photovoltaic performance arising from insufficient absorption of low-energy photons demands careful design of light management to maximize the efficiency and preserve the cost-effectiveness of solar cells. Herein we present an integrated flexible solar module of ultrathin, nanostructured silicon solar cells capable of simultaneously exploiting spectral upconversion and downshifting in conjunction with multispectral luminescent waveguides and a nanostructured plasmonic reflector to compensate for their weak optical absorption and enhance their performance. The 8 $μ$m-thick silicon solar cells incorporating a hexagonally periodic nanostructured surface relief are surface-embedded in layered multispectral luminescent media containing organic dyes and NaYF 4 :Yb 3+ ,Er 3+ nanocrystals as downshifting and upconverting luminophores, respectively, via printing-enabled deterministic materials assembly. The ultrathin nanostructured silicon microcells in the composite luminescent waveguide exhibit strongly augmented photocurrent (~40.1 mA/cm 2 ) and energy conversion efficiency (~12.8%) than devices with only a single type of luminescent species, owing to the synergistic contributions from optical downshifting, plasmonically enhanced upconversion, and waveguided photon flux for optical concentration, where the short-circuit current density increased by ~13.6 mA/cm 2 compared with microcells in a nonluminescent medium on a plain silver reflector under a confined illumination.

36 MATERIALS SCIENCE↗

Bypass diode for a solar cell

Methods of fabricating bypass diodes for solar cells are described. In once embodiment, a method includes forming a first conductive region of a first conductivity type above a substrate of a solar cell. A second conductive region of a second conductivity type is formed on the first conductive region. In another embodiment, a method includes forming a first conductive region of a first conductivity type above a substrate of a solar cell. A second conductive region of a second conductivity type is formed within, and surrounded by, an uppermost portion of the first conductive region but is not formed in a lowermost portion of the first conductive region.

14 SOLAR ENERGY↗

Solar cell encapsulation

A polymer syrup for encapsulating solar cell assemblies. The syrup includes uncrosslinked poly(n-butyl)acrylate dissolved in n-butyl acrylate monomer. Preparation of the poly(n-butyl)acrylate and preparation of the polymer syrup is disclosed. Methods for applying the polymer syrup to solar cell assemblies as an encapsulating pottant are described. Also included is a method for solar cell construction utilizing the polymer syrup as a dual purpose adhesive and encapsulating material.

Gupta, Amitava↗

Hybrid Organic-Inorganic Composite Solar Cells for Efficient, Low Cost, Photoelectric Energy Conversion (Technical Report)

Cadmium selenide nanoparticles and nanoclusters were prepared and added to polymer solar cells to improve their photon capture ability. These nanoparticles did exhibit some beneficial effects on the photon conversion efficiencies of selected polymer solar cells. Ternary bulk heterojunction systems based on composites of methyl viologen-doped, CdSe nanoparticles blended with poly (3-hexothiopene) (P3HT) and 6, 6-phenyl C 61 -butyric acid methyl ester (PCBM) were also tested. It was found that the devices with methyl viologen-doped CdSe nanoparticles do produce more photocurrent in a region surrounding the absorption peak of the particles (560 to 660nm) when compared to pristine P3HT:PCBM devices. Gold nanorods were also prepared and tested in some solar cells. These nanorods did produce a very small enhancement in photon absorbance, but the observed increase the photon conversion efficiency was not sufficient to make the effort worthwhile. Our goals were (1) to prepare cadmium sulfide and cadmium selenide clusters and nanoparticles to be tested as photon absorbers to enhance the photon conversion efficiency of polymer solar polymer solar cells and (2) to prepare gold and silver nanorods to be added to polymer solar cells to enhance their photon capture capability. The cadmium sulfide and cadmium selenide nanoparticles and some new nanoclusters were prepared. The cadmium selenide nanoparticles were also tested in solar cells and did exhibit some positive effects when they were combined with certain co-absorbing polymers. Due to solubility problems that were not solved in the available time, the new nanoclusters were not tested in solar cells. Ternary bulk heterojunction systems based on composites of methyl viologen doped, CdSe nanoparticles blended with poly (3-hexothiopene) (P3HT) and 6, 6-phenyl C 61 -butyric acid methyl ester (PCBM) have been examined in detail. The methyl viologen was added to promote charge separation of the initially formed excitons. It was found that the devices with CdSe produce more photocurrent in a region surrounding the absorption peak of the particles (560 to 660nm) when compared to a pristine P3HT:PCBM device. Gold nanorods were prepared and tested in some solar cells. These did show a very small enhancement in photon absorbance. However, the increase in short circuit current was negligible, which suggests that this antenna effect produces no significant increase in photocurrent generation. Efforts to synthesize niobium-doped zinc oxide nanoparticles for use in polymer solar polymer solar cells were also made. The nanoparticles were prepared, but they were not tested in the cells before the termination of the funding of the project.

14 SOLAR ENERGY↗

Solution processable organic polymers and small molecules for bulk-heterojunction solar cells: A review

Solution processed bulk heterojunction (BHJ) organic solar cells (OSCs) have gained wide interest in past few years and are established as one of the leading next generation photovoltaic technologies for low cost power production. Power conversion efficiencies up to 6% and 6.5% have been reported in the literature for single layer and tandem solar cells, respectively using conjugated polymers. A recent record efficiency about 8.13% with active area of 1.13 cm{sup 2} has been reported. However Solution processable small molecules have been widely applied for photovoltaic (PV) devices in recent years because they show strong absorption properties, and they can be easily purified and deposited onto flexible substrates at low cost. Introducing different donor and acceptor groups to construct donor--acceptor (D--A) structure small molecules has proved to be an efficient way to improve the properties of organic solar cells (OSCs). The power conversion efficiency about 4.4 % has been reported for OSCs based on the small molecules. This review deals with the recent progress of solution processable D--A structure small molecules and discusses the key factors affecting the properties of OSCs based on D--A structure small molecules: sunlight absorption, charge transport and the energy level of the molecules.

14 SOLAR ENERGY↗

Monolithic Two-Terminal All-Perovskite Tandem Solar Cells with Power Conversion Efficiency Exceeding 21%

Monolithic two-terminal (2-T) all-perovskite tandem solar cells are a promising candidate for the next generation solar cells with ultrahigh efficiency and low fabrication cost. Here, we report on the fabrication of 2-T all-perovskite tandem solar cells consisting of solution-processed wide-bandgap and low-bandgap perovskite subcells connected by a vacuum processed interconnection layer. We employed a bulk-passivation strategy to enlarge the grain size, increase carrier mobilities, reduce electronic disorder, and suppress trap-assisted recombination in the low bandgap mixed Sn-Pb perovskite films, which leads to improved performance of low bandgap perovskite solar cells with an absorber thickness over 750 nm. This advance in high-quality low-bandgap perovskite layers enables the fabrication of efficient 2-T all-perovskite solar cells with power conversion efficiencies of more than 21% and decent stability. Our approach provides a suitable pathway to realize ultra-high efficiency 2-T all-perovskite tandem solar cells.

14 SOLAR ENERGY↗

Waved glass: Towards optimal light distribution on solar cell surfaces for high efficient modules

A method to improve the module efficiency of solar cells by modifying the surface of the glass cover of the solar cells module is proposed. A model is built to show that a better efficiency can be achieved by optimizing the light distribution on the cell, which reduces the shadow losses and thereby allows the finger spacing to be decreased, which in turn decreases the (resistive) ohmic losses. This method is illustrated by considering industrial crystalline silicon solar cells as an example, however, it applies to all solar cells that are characterized by a metallization pattern on the surface of the solar cell. It is estimated that this method can improve the relative module efficiency by about 5% and halve the front side losses. (author)

14 SOLAR ENERGY↗

Optimized scalable stack of fluorescent solar concentrator systems with bifacial silicon solar cells

In this paper, we present a concentrator system based on a stack of fluorescent concentrators (FCs) and a bifacial solar cell. Coupling bifacial solar cells to a stack of FCs increases the performance of the system and preserves its efficiency when scaled. We used an approach to optimize a fluorescent solar concentrator system design based on a stack of multiple fluorescent concentrators (FC). Seven individual fluorescent collectors (20 mm×20 mm×2 mm) were realized by in-situ polymerization and optically characterized in regard to their ability to guide light to the edges. Then, an optimization procedure based on the experimental data of the individual FCs was carried out to determine the stack configuration that maximizes the total number of photons leaving edges. Finally, two fluorescent concentrator systems were realized by attaching bifacial silicon solar cells to the optimized FC stacks: a conventional system, where FC were attached to one side of the solar cell as a reference, and the proposed bifacial configuration. It was found that for the same overall FC area, the bifacial configuration increases the short-circuit current by a factor of 2.2, which is also in agreement with theoretical considerations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dynamic Coupling between Electrode Interface and Donor/Acceptor Interface via Charge Dissociation in Organic Solar Cells at Device-Operating Condition

Organic solar cells exhibit both electrode/photovoltaic (E/P) interface and donor/acceptor (D/A) interface in controlling the critical photovoltaic processes. Here, on the basis of the efficient PTB7:PC71BM solar cells, our studies on magneto-photocurrent with external bias provide the first evidence that the E/P interface and D/A interface are dynamically coupled at device-operating condition. Specifically, we observe a significant decrease (90%) in the critical bias required to completely dissociate the charge transfer (CT) states at D/A interface by changing the E/P interface with increased interface dipole field from ZnO to the polyelectrolyte (PFN). The experimental results demonstrate that strong dipole field at the E/P interface can effectively decrease the electron hole binding energy at D/A interface through the enhancement of built-in field applied on CT states. Clearly, our experimental studies provide new insight on the interfacial engineering through addressing the dynamic coupling between E/P interface and D/A interface in organic bulkheterojunction solar cells toward further improvement on photovoltaic efficiencies.

14 SOLAR ENERGY↗

High-Efficiency Recycled Silicon Solar Cell

The project, High-Efficiency Recycled Silicon Solar Cell, addresses the critical challenge of end-of-life (EoL) photovoltaic (PV) waste, which is expected to reach 78 million tons by 2050. Traditional recycling methods for recovering valuable materials like silver from silicon solar cells are inefficient, environmentally harmful, and economically unfeasible. Therefore, presently waste solar cells end up as landfills. This project aimed to develop a green, scalable, laser-based method for silver recovery, avoiding hazardous chemicals and minimizing operational costs. This research contributes to the circular economy in the renewable energy sector by enhancing material recovery from PV waste.

14 SOLAR ENERGY↗

Donor-fullerene dyads for energy cascade organic solar cells

Organic bulk hetero junction (BHJ) solar cells require broad absorption of the incident solar spectrum by the donor and acceptor in the blend. Fullerene derivatives with covalently linked dyes, referred to as dyads, were designed to have strong optical absorption and appropriate electronic levels for electron transfer with common donor polymers in BHJs. Dyads with dyes based on diketopyrrolopyrrole and benzothiadiazole were synthesized using either a methanofullerene or a fulleropyrrolidine linkage. Here, the performance of these dyad acceptors in BHJ solar cells with poly(3-hexylthiophene) (P3HT) and a low optical gap co-polymer of thiophene and diketopyrrolopyrrole (PDPP2FT) were examined. Although the solar power conversion efficiencies were low, charge generation from the molecular dye in the dyad could be observed in BHJs with PDPP2FT. The low power conversion efficiency was attributed to the morphology of the BHJs based on grazing incidence wide angle X-ray scattering patterns. Density functional theory was used to examine the charge transfer states between the donor and the dyad. The lowest energy charge-transfer state was found to be a transition from the donor polymer to the fullerene portion of the dyad.

14 SOLAR ENERGY↗

Construction of Solar Cells from Colloidal Nanocrystals through Electrophoretic Deposition

Colloidal nanocrystal based solar cells have shown great potential as next generation low-cost solar cells. However, one of the biggest scientific challenges for the colloidal nanocrystal solar cells is their low efficiency, mainly due to the loss of photo-generated charge carriers during their transport across the nanocrystal film. Poor electronic coupling and disorder in the nanocrystal array are both responsible for the carrier loss, because they slow down the carrier transport, leading to a high recombination-induced carrier loss. Our strategy to improve solar cell efficiency is to increase the nanocrystal size homogeneity in the film. In this project, we demonstrated a novel and general approach to control the assembly of semiconductor nanocrystals into superlattice films with tunable grain sizes via electrophoretic deposition (EPD). This work not only presents an efficient (micron-thick films within a few minutes), scalable, low-cost method to fabricate thick semiconductor superlattice films, but also offers a platform that enables in situ studies of the ordering process and can be used to explore the correlation between packing order of nanocrystals and electronic properties of colloidal nanocrystal films. In addition, we proposed possible charging mechanism by taking ligand chemistry into account, which is critical for the EPD process, by using first principles calculations.

36 MATERIALS SCIENCE↗

Solar cell with doped groove regions separated by ridges

Solar cells with doped groove regions separated by ridges and methods of fabricating solar cells are described. In an example, a solar cell includes a substrate having a surface with a plurality of grooves and ridges. A first doped region of a first conductivity type is disposed in a first of the grooves. A second doped region of a second conductivity type, opposite the first conductivity type, is disposed in a second of the grooves. The first and second grooves are separated by one of the ridges.

14 SOLAR ENERGY↗

Comparative Life Cycle Analysis of Scalable Single-Junction and Tandem Perovskite Solar Cell (PSC) Systems

Efficient, low-cost solar cells based upon perovskites have the potential to transform the US and global energy portfolio and improve energy security if they can be manufactured in an environmentally sustainable manner. However, previous life cycle analyses (LCA) of perovskite solar cells (PSC) used lab recipes to project the environmental impact of industrial PSC production – using materials and processes that may not be representative of industrial productions due to high material waste and complex synthesis – and such studies were limited to a few single-junction technologies. Thus, the goal of this project was threefold: a) to review the most promising for industrial production single-junction and tandem PSC technologies, b) to build life-cycle materials inventories that reflect scalable production of these technologies, and c) to conduct comprehensive life-cycle analysis of these technologies and compare their environmental impact with those of established commercial technologies. In response, this project identified challenges for fabrication transitioning from laboratory to sustainable industrial production, developed life-cycle inventory (LCI) data for scaling to industrial production four promising single-junction and three tandem PSC systems and produced life-cycle-investigations using, as metrics, a complete spectrum of energy, environmental and ecological impact indicators. Special focus was given to the use of lead, silver and indium in PSC. The project used the Life Cycle Assessment (LCA) methodology as standardized by the Society of Environmental Toxicology and Chemistry (SETAC), ISO standards 14040 and 14044, and the International Energy Agency PVPS Task 12 LCA guidelines. LCA allows the calculation of a number of energy and environmental and impact categories, including energy cumulative energy demand (CED), global warming potential (GWP), human toxicity potential (HTP), eco-toxicity potential (ETP), abiotic resource depletion potential (ADP), acidification potential (AP), ozone depletion potential (ODP), photochemical oxidation potential (POP), eutrophication potential (EP). In addition to those, we calculated the Energy Pay-Back Time (EPBT) and the Energy Return On Investment (EROI). We provide LCA impacts for complete perovskite PV systems – including balance of system components – installed at three irradiation levels and considering reference and future potential module efficiencies. Finally, a sensitivity analysis on perovskite lifetime has been performed, considering 10, 20 and 30 years. Contribution analysis of the impacts of each material and layer of PSC shows, that the use of Pb in metalorganic PSC does not result in significant environmental impacts as the major contributions to environmental indicators arise from the use of Ag and encapsulation materials. Solution-based PSC manufacturing was found to be less impactful to the environment than vapor-based fabrication, and roll-to-roll (RtR) printing uses less energy and generates the lowest emissions. PSC produced with RtR manufacturing could reach the same Energy Return on Energy Investment (EROI) as that of crystalline-Si PV within 12 years of life, whereas the most energy demanding spray coating on rigid substrates, would require a 20-yr life to match the EROI of 30-yr lasting silicon PV. This work lays the foundation for sustainability investigations in a comparative context of large-scale production and deployment of PSC. The results of this project have the potential to have a significant impact on the future of PV manufacturing, by providing industry, policy-makers, and academia with insights necessary to choose which, if any, lead-based solar cell life cycles are environmentally sustainable.

14 SOLAR ENERGY↗

Alkyl Chain Length Effects of Polymer Donors on the Morphology and Device Performance of Polymer Solar Cells with Different Acceptors

Abstract The development of nonfullerene acceptors has brought polymer solar cells into a new era. Maximizing the performance of nonfullerene solar cells needs appropriate polymer donors that match with the acceptors in both electrical and morphological properties. So far, the design rationales for polymer donors are mainly borrowed from fullerene‐based solar cells, which are not necessarily applicable to nonfullerene solar cells. In this work, the influence of side chain length of polymer donors based on a set of random terpolymers PTAZ‐TPD10‐C n on the device performance of polymer solar cells is investigated with three different acceptor materials, i.e., a fullerene acceptor [70]PCBM, a polymer acceptor N2200, and a fused‐ring molecular acceptor ITIC. Shortening the side chains of polymer donors improves the device performance of [70]PCBM‐based devices, but deteriorates the N2200‐ and ITIC‐based devices. Morphology studies unveil that the miscibility between donor and acceptor in blend films depends on the side chain length of polymer donors. Upon shortening the side chains of the polymer donors, the miscibility between the donor and acceptor increases for the [70]PCBM‐based blends, but decreases for the N2200‐ and ITIC‐based blends. These findings provide new guidelines for the development of polymer donors to match with emerging nonfullerene acceptors.

Pang, Shuting↗