Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Simulator Study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Assessing the use of portable air cleaners for reducing exposure to airborne diseases in a conference room with thermal stratification

The COVID-19 pandemic has highlighted the need for strategies that mitigate the risk of aerosol disease transmission in indoor environments with different ventilation strategies. It is necessary for building operators to be able to estimate and compare the relative impacts of different mitigation strategies to determine suitable strategies for a particular situation. Using a validated CFD model, this study simulates the dispersion of exhaled contaminants in a thermally stratified conference room with overhead heating. The impacts of portable air-cleaners (PACs) on the room airflow and contaminant distribution were evaluated for different PAC locations and flow rates, as well as for different room setups (socially distanced or fully occupied). To obtain a holistic view of a strategy's impacts under different release scenarios, we simultaneously model the steady-state distribution of aerosolized virus contaminants from eight distinct sources in 18 cases for a total of 144 release scenarios. The simulations show that the location of the source, the PAC settings, and the room set-up can impact the average exposure and PAC effectiveness. For this studied case, the PACs reduced the room average exposure by 31%-66% relative to the baseline case. Some occupant locations were shown to have a higher-than-average exposure, particularly those seated near the airflow outlet, and occupants closest to sources tended to see the highest exposure from said source. We found that these PACs were effective at reducing the stratification caused by overhead heating, and also identified at least one sub-optimal location for placing a PAC in this space.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Post-detonation fireball modeling: Validation of freeze out approximations

A numerical simulation study was performed to examine the post-detonation reaction processes produced by the detonation of a 12 mm diameter hemispherical pentaerythritol tetranitrate (PETN) explosive charge. The simulations used a finite rate detailed chemical reaction model consisting of 59 species and 368 reactions to capture post-detonation reaction processes including air dissociation from Mach 19+ shock waves that initially break out of the PETN charge, reactions within the detonation products during expansion, and afterburning when the detonation products mix with the shock heated air. The multi-species and thermodynamically complete Becker-Kistiakowsky-Wilson real-gas equation of state is used for the gaseous phase to allow for the mixing of reactive species. A recent simplified reactive burn model is used to propagate the detonation through the charge and allow for detailed post-detonation reaction processes. The computed blast, shock structures, and mole fractions of species within the detonation products agree well with experimental measurements. A comparison of the simulation results to equilibrium calculations indicates that the assumption of a local equilibrium is fairly accurate until the detonation products rapidly cool to temperatures in the range of 1500-1900 K by expansion waves. Below this range, the computed results show mole fractions that are nearly chemically frozen within the detonation products for a significant portion of expansion. In conclusion, these results are consistent with the freeze out approximation used in the blast modeling community.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1992

Flight Testing and Simulation of an F-15 Airplane Using Throttles for Flight Control

Flight tests and simulation studies using the throttles of an F-15 airplane for emergency flight control have been conducted at the NASA Dryden Flight Research Facility. The airplane and the simulation are capable of extended up-and-away flight, using only throttles for flight path control. Initial simulation results showed that runway landings using manual throttles-only control were difficult, but possible with practice. Manual approaches flown in the airplane were much more difficult, indicating a significant discrepancy between flight and simulation. Analysis of flight data and development of improved simulation models that resolve the discrepancy are discussed. An augmented throttle-only control system that controls bank angle and flight path with appropriate feedback parameters has also been developed, evaluated in simulations, and is planned for flight in the F-15.

Propulsion-only control↗
NASA NTRS1992

Flight Testing and Simulation of an F-15 Airplane Using Throttles for Flight Control

Flight tests and simulation studies using the throttles of an F-15 airplane for emergency flight control have been conducted at the NASA Dryden Flight Research Facility. The airplane and the simulation are capable of extended up-and-away flight, using only throttles for flightpath control. Initial simulation results showed that runway landings using manual throttles only control were difficult, but possible with practice. Manual approaches flown in the airplane were much more difficult, indicating a significant discrepancy between flight and simulation. Analysis of flight data and development of improved simulation models that resolve the discrepancy are discussed. An augmented throttles-only control system that controls bank angle and flightpath with appropriate feedback parameters has also been developed, evaluated in simulations, and is planned for flight in the F-15.

Flight Testing↗
NASA NTRS1996

Influence of Back-Up Bearings and Support Structure Dynamics on the Behavior of Rotors With Active Supports

This report presents a synopsis of the research work. Specific accomplishments are itemized below: (1) Experimental facilities have been developed. This includes a magnetic bearing test rig and an auxiliary bearing test rig. In addition, components have been designed, constructed, and tested for use with a rotordynamics test rig located at NASA Lewis Research Center. (2) A study of the rotordynamics of an auxiliary bearing supported T-501 engine model was performed. (3) An experimental/simulation study of auxiliary bearing rotordynamics has been performed. (4) A rotordynamical model for a magnetic bearing supported rotor system, including auxiliary bearing effects has been developed and simulation studies performed.(5) A finite element model for a foil bearing has been developed and studies of a rotor supported by foil bearings have been performed. (6) Two students affiliated with this project have graduated with M.S. degrees.

Flowers, George T.↗
DOE OSTI2020

Digitization modeling of a CGEM detector based on Garfield++ simulation

Abstract Background The Cylindrical Gas Electron Multiplier Inner Tracker (CGEM-IT) is one of the candidates for the replacement of the current BESIII inner drift chamber, which has developed serious aging effects due to beam-related backgrounds. Purpose To build a full digitization model, it is necessary to understand the electron drift behavior and signal induction. Methods A simulation study based on Garfield++ and ANSYS software has been performed. Results Parameters describing the Lorentz angle, diffusion effect, drift time, multiplication, and induction are obtained from the Garfield++ simulation. Based on these results, a preliminary digitization model is implemented in the BESIII offline software system.

Zhao, Jing-Yi (ORCID:0000000220287286)↗
NASA NTRS1994

Microburst vertical wind estimation from horizontal wind measurements

The vertical wind or downdraft component of a microburst-generated wind shear can significantly degrade airplane performance. Doppler radar and lidar are two sensor technologies being tested to provide flight crews with early warning of the presence of hazardous wind shear. An inherent limitation of Doppler-based sensors is the inability to measure velocities perpendicular to the line of sight, which results in an underestimate of the total wind shear hazard. One solution to the line-of-sight limitation is to use a vertical wind model to estimate the vertical component from the horizontal wind measurement. The objective of this study was to assess the ability of simple vertical wind models to improve the hazard prediction capability of an airborne Doppler sensor in a realistic microburst environment. Both simulation and flight test measurements were used to test the vertical wind models. The results indicate that in the altitude region of interest (at or below 300 m), the simple vertical wind models improved the hazard estimate. The radar simulation study showed that the magnitude of the performance improvement was altitude dependent. The altitude of maximum performance improvement occurred at about 300 m.

Vicroy, Dan D.↗
DOE OSTI2022

A hierarchical stochastic modeling approach for representing point bar geometries and petrophysical property variations

The flow of fluids in point bars is affected by the existence of heterogeneities like shale drapes that are found on the surfaces of inclined heterolithic stratifications. In fact, these shale drapes can act as fluid flow baffles; therefore, developing a framework for modeling point bars and their associated heterogeneities is vital. In this study, a stochastic process-based modeling approach is presented for capturing the main point bar heterogeneities: accretion surfaces (i.e., the aerial heterogeneity) and inclined heterolithic stratifications (i.e., the vertical heterogeneity). The former was modeled using a sine-generation function and the latter, with a sigmoidal function after which they were combined into a 3D point bar model. To ensure proper modeling of petrophysical properties, we developed a more representative gridding scheme which generates curvilinear grids representative of the point bar geometry. This grid was then transformed into a rectilinear grid to allow for geostatistical simulation after which all petrophysical properties were mapped back into the original curvilinear grid. An essential element of this modeling approach is the stochastic representation of shale drapes at the interface between successive accretion surfaces. The workflow was tested using a real field dataset for the Cranfield field, Mississippi. The constructed model was then subjected to a flow simulation study mimicking a CO 2 storage scenario. Various sensitivities were simulated to evaluate the effect of heterogeneities on CO 2 flow within the point-bar. Results demonstrate the importance of representing point-bar related heterogeneity and the spatial distribution of shale drapes on CO 2 plume migration and storage.

58 GEOSCIENCES↗
NASA NTRS1976

Application of a helicopter mathematical model to the Langley differential maneuvering simulator for use in a helicopter/fighter evasive maneuver study

A real time simulation study was conducted using a differential maneuvering simulator to determine and evaluate helicopter evasive maneuvers when attacked by fighter aircraft. A general helicopter mathematical model was modified to represent an H-53 helicopter. The helicopter model was compared to H-53 flight test data to determine any differences between the simulated and actual vehicles. The simulated helicopter was also subjectively validated by participating pilots. Two fighter mathematical models validated in previous studies were utilized for the attacking aircraft. The results of this simulation study have been verified in a flight test program conducted by the U. S. Air Force and were found to closely match the flight results.

Houck, J. A.↗
DOE OSTI2019

Effects of grain boundaries on conversion efficiencies of single-crystal-like GaAs thin-film solar cells on flexible metal tapes

We present a numerical simulation study of the effects of low-angle grain boundaries (GBs) in a single-crystal-like GaAs thin-film material on its photovoltaic performance. Here, 1D and 2D modeling are employed to simulate a solar-cell (SC) device based on the properties of single-crystal-like GaAs thin films grown on metal tape. Properties include minority carriers’ mobility, carrier lifetimes, and diffusion length. The 1D model, by incorporating a uniform biaxially textured GaAs compared to single crystal GaAs, predicts an efficiency ~21% for average carrier lifetimes of 1 ns. This result is not consistent with an experimental results showing an efficiency of 4.3%. 1D simulation generally works well for the prediction of conventional crystalline SC I-V characteristics, but it fails for newly-developed single-crystal-like GaAs SC devices with different material properties and non-vertical device geometry. Hence, we develop a 2D model to study the effect of localized recombination centers in the material by defining different regions of defective low-angle grain boundaries and single crystalline intra-grains. The 2D model is comparable to the experimental results mainly due to its capability to consider localized material inhomogeneity and lateral carriers dynamic. The effect of grain boundary density on SC performance is studied by 2D modeling. Increasing the grain size of GaAs from 2 μm to 50 μm can improve efficiency from 4.8% to 12.3%. The open-circuit voltage (Voc) shows more sensitivity to varying grain boundary densities than other SC characteristic factors. The 2D model is also employed to study bulk passivation of GBs and suggests that an efficiency of ~19.5% is achievable in the single-crystal-like GaAs SCs even with a small grain size of 2 μm, if effective grain boundary passivation is applied.

14 SOLAR ENERGY↗
NASA NTRS2016

Comparing Potential Recharge Estimates From Three Land Surface Models Across the Western US

Groundwater is a major source of water in the western US. However, there are limited recharge estimates available in this region due to the complexity of recharge processes and the challenge of direct observations. Land surface Models (LSMs) could be a valuable tool for estimating current recharge and projecting changes due to future climate change. In this study, simulations of three LSMs (Noah, Mosaic and VIC) obtained from the North American Land Data Assimilation System (NLDAS-2) are used to estimate potential recharge in the western US Modeled recharge was compared with published recharge estimates for several aquifers in the region. Annual recharge to precipitation ratios across the study basins varied from 0.01-15% for Mosaic, 3.2-42% for Noah, and 6.7-31.8% for VIC simulations. Mosaic consistently underestimates recharge across all basins. Noah captures recharge reasonably well in wetter basins, but overestimates it in drier basins. VIC slightly overestimates recharge in drier basins and slightly underestimates it for wetter basins. While the average annual recharge values vary among the models, the models were consistent in identifying high and low recharge areas in the region. Models agree in seasonality of recharge occurring dominantly during the spring across the region. Overall, our results highlight that LSMs have the potential to capture the spatial and temporal patterns as well as seasonality of recharge at large scales. Therefore, LSMs (specifically VIC and Noah) can be used as a tool for estimating future recharge rates in data limited regions.

groundwater↗
NASA NTRS2012

The Influence of Pickup Protons, from Interstellar Neutral Hydrogen, on the Propagation of Interplanetary Shocks from the Halloween 2003 Solar Events to ACE and Ulysses: A 3-D MHD Modeling Study

We describe our 3-D, time ]dependent, MHD solar wind model that we recently modified to include the physics of pickup protons from interstellar neutral hydrogen. The model has a time-dependent lower boundary condition, at 0.1 AU, that is driven by source surface map files through an empirical interface module. We describe the empirical interface and its parameter tuning to maximize model agreement with background (quiet) solar wind observations at ACE. We then give results of a simulation study of the famous Halloween 2003 series of solar events. We began with shock inputs from the Fearless Forecast real ]time shock arrival prediction study, and then we iteratively adjusted input shock speeds to obtain agreement between observed and simulated shock arrival times at ACE. We then extended the model grid to 5.5 AU and compared those simulation results with Ulysses observations at 5.2 AU. Next we undertook the more difficult tuning of shock speeds and locations to get matching shock arrival times at both ACE and Ulysses. Then we ran this last case again with neutral hydrogen density set to zero, to identify the effect of pickup ions. We show that the speed of interplanetary shocks propagating from the Sun to Ulysses is reduced by the effects of pickup protons. We plan to make further improvements to the model as we continue our benchmarking process to 10 AU, comparing our results with Cassini observations, and eventually on to 100 AU, comparing our results with Voyager 1 and 2 observations.

Detman, T. R.↗
DOE OSTI2023

Impacts of Permeability Heterogeneity and Background Flow on Supercritical CO 2 Dissolution in the Deep Subsurface

Motivated by CO 2 capture and sequestration (CCS) design considerations, we consider the coupled effects of permeability heterogeneity and background flow on the dissolution of a supercritical CO 2 lens into an underlying deep, confined aquifer. We present the results of a large-scale Monte Carlo simulation study examining the interaction of background flow rate and three parameters describing multi-Gaussian log-permeability fields: mean, variance, and correlation length. Hundreds of high-resolution simulations were performed using the PFLOTRAN finite volume software to model CO 2 dissolution in a kilometer-scale aquifer over 1,000 years. Predictive dimensionless scaling relationships relating CO 2 dissolution rate to heterogeneity statistics, Rayleigh (Ra) and Péclet (Pe) numbers were developed for both gravitationally dominated free convection to background flow-dominated forced convection regimes. An empirical criterion, Pe = Ra 3/4 , was discovered for regime transition. All simulations converged quickly to a quasi-steady, approximately linear dissolution rate. However, this rate displayed profound variability between permeability field realizations sharing the same heterogeneity statistics, even under mild permeability heterogeneity. In general, increased heterogeneity was associated with a lower mean and higher variance of dissolution rate, undesirable from a CCS design perspective. The relationship between dissolution rate and background flow was found to be complex and nonlinear. Dimensionless scaling relationships were uncovered for a number of special cases. Results call into question the validity of the Boussinesq approximation in the context of modest-to-high background flow rates and the general applicability of numerical simulations without background flow.

42 ENGINEERING↗
NASA NTRS1976

Investigation of LANDSAT follow-on thematic mapper spatial, radiometric and spectral resolution

The author has identified the following significant results. Fine resolution M7 multispectral scanner data collected during the Corn Blight Watch Experiment in 1971 served as the basis for this study. Different locations and times of year were studied. Definite improvement using 30-40 meter spatial resolution over present LANDSAT 1 resolution and over 50-60 meter resolution was observed, using crop area mensuration as the measure. Simulation studies carried out to extrapolate the empirical results to a range of field size distributions confirmed this effect, showing the improvement to be most pronounced for field sizes of 1-4 hectares. Radiometric sensitivity study showed significant degradation of crop classification accuracy immediately upon relaxation from the nominally specified values of 0.5% noise equivalent reflectance. This was especially the case for data which were spectrally similar such as that collected early in the growing season and also when attempting to accomplish crop stress detection.

Nalepka, R. F.↗
NASA NTRS2002

A Biologically Inspired Cooperative Multi-Robot Control Architecture

A prototype cooperative multi-robot control architecture suitable for the eventual construction of large space structures has been developed. In nature, there are numerous examples of complex architectures constructed by relatively simple insects, such as termites and wasps, which cooperatively assemble their nests. The prototype control architecture emulates this biological model. Actions of each of the autonomous robotic construction agents are only indirectly coordinated, thus mimicking the distributed construction processes of various social insects. The robotic construction agents perform their primary duties stigmergically i.e., without direct inter-agent communication and without a preprogrammed global blueprint of the final design. Communication and coordination between individual agents occurs indirectly through the sensed modifications that each agent makes to the structure. The global stigmergic building algorithm prototyped during the initial research assumes that the robotic builders only perceive the current state of the structure under construction. Simulation studies have established that an idealized form of the proposed architecture was indeed capable of producing representative large space structures with autonomous robots. This paper will explore the construction simulations in order to illustrate the multi-robot control architecture.

Howsman, Tom↗
NASA NTRS2004

A Stigmergic Cooperative Multi-Robot Control Architecture

In nature, there are numerous examples of complex architectures constructed by relatively simple insects, such as termites and wasps, which cooperatively assemble their nests. A prototype cooperative multi-robot control architecture which may be suitable for the eventual construction of large space structures has been developed which emulates this biological model. Actions of each of the autonomous robotic construction agents are only indirectly coordinated, thus mimicking the distributed construction processes of various social insects. The robotic construction agents perform their primary duties stigmergically, i.e., without direct inter-agent communication and without a preprogrammed global blueprint of the final design. Communication and coordination between individual agents occurs indirectly through the sensed modifications that each agent makes to the structure. The global stigmergic building algorithm prototyped during the initial research assumes that the robotic builders only perceive the current state of the structure under construction. Simulation studies have established that an idealized form of the proposed architecture was indeed capable of producing representative large space structures with autonomous robots. This paper will explore the construction simulations in order to illustrate the multi-robot control architecture.

Howsman, Thomas G.↗
DOE OSTI2019

Effects of water on the stochastic motions of propane confined in MCM-41-S pores

Hydrocarbons confined in porous media find applications in a wide variety of industries and therefore their diffusive behavior is widely studied. Most of the porous media found in natural environments are laden with water, which might affect the confined hydrocarbons. To quantify the effect of hydration, we report here a combined quasielastic neutron scattering (QENS) and molecular dynamics (MD) simulation study on the dynamics of propane confined in the 1.5 nm-wide micropores of MCM-41-S in the presence of water at 230 and 250 K. To eliminate the strong incoherent signal from water and emphasize the propane signal we have used heavy water (D 2 O). QENS data show two dynamically different populations of propane in MCM-41-S and suggest that the presence of water hinders the diffusion of propane. Weak elastic contributions to the QENS spectra suggest that only long-range translational motion of propane molecules contributes to the quasielastic broadening. MD simulations carried out using a model cylindrical silica pore of 1.6 nm diameter filled with water and propane agree with the experimental finding of water hindering the diffusion of propane. Further, the simulation results suggest that the slowing down of propane motions is a function of the water content within the pore and is stronger at higher water contents. At high water content, the structure and the dynamics, both translational and rotational, of propane are severely impacted. Simulation data suggest that the rotational motion of the propane molecule occurs on time scales much faster than those accessible with the QENS instrument used, and thus explain the weak elastic contribution to the QENS spectra measured in the experiments. This study shows the effects of hydration on the structure and dynamics of volatiles in porous media, which are of interest for fundamental understanding and applied studies of confined fluids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗