Chemical imaging and diffusion of hydrogen and lithium in lithium aluminate
Not Available
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
In the fusion reactors, plasma facing materials (PFMs) will be bombarded by large amounts of energetic particles, including helium (He) atoms. These metal-insoluble He atoms are prone to self-trapping or are trapped by vacancies, dislocation cores or grain boundaries, aggregating to form high concentration He bubbles which leads to serious degradation of the PFMs’ properties. Studying the initial stages of He-defect interactions becomes increasingly important because it not only helps us understand the formation mechanism of He bubbles but also provides insight to help design new irradiation-resistant PFMs. As such, in this work we used the positron annihilation Doppler broadening spectroscopy (DBS) and secondary ion mass spectrometry (SIMS) to explore the evolutions of the interactions between vacancy-type defects and He and the retention of He in the nanochannel W film irradiated with 190 keV He + ions to different fluences under different temperatures. It is found that the presence of a nanochannel structure accelerates the release of He from the film even at low irradiation fluences, and the release of He is significantly enhanced at higher fluences, thus inhibiting or delaying the formation of large He-vacancy clusters in the nanochannel W film. Both irradiation fluence and temperature have significant influence on the formation and evolution of He-vacancy clusters, and the evolution of these microstructure also causes hardness changes.
Degradation mechanisms in LiV 3 O 8 cathode films (~500 nm) with different initial microstructures i.e., globular nanocrystals in amorphous matrix and needle-like nanocrystals, synthesized by annealing the cathodes at 150 °C and 300 °C for 6 h are studied by Transmission Electron Microscopy (TEM) and Auger Electron Spectroscopy (AES). In addition, a unique in-situ combination of TEM and Secondary Ion Mass Spectrometry (SIMS) imaging techniques, namely Parallel Ion and Electron beam Spectrometry (PIES) is carried out to measure the 3D distribution of V and Li with nanoscale resolution. These characterization studies focus on correlating the pre- and post-cycling microstructure to observed electrochemical performance. The LiV 3 O 8 cathode film with needle-like nanocrystals (300 °C) shows a higher initial capacity but it degrades rapidly compared to the film with globular nanocrystals embedded in amorphous matrix (150 °C). We observed that LiV 3 O 8 films with needle-like nanocrystals are more susceptible to cathode decohesion and vanadium dissolution than the films with globular nanocrystals embedded in amorphous matrix, explaining the differences in their electrochemical performance. The findings from this study have relevance to the development of thin film electrode microstructures for high capacity and cyclic stability.
Alloying anode materials for lithium-ion batteries, such as silicon (Si), are an important focus of materials research due to the demand for increased energy density for electric vehicles and stationary grid storage. However, progress towards next generation anode materials has been hindered by poor capacity retention due to the instability of the Si active material and the solid electrolyte interphase (SEI). Herein, the evolution of the active Si material and the SEI are simultaneously investigated from the perspective of chemical, structural, morphological, and electronic evolution in the Si wafer model system through its cycling life, using time-of-flight secondary ion mass spectrometry (TOF-SIMS), scanning transmission electron microscopy (STEM), atomic force microscopy (AFM), and scanning spreading resistance microscopy (SSRM). The results illustrate a dynamic evolution of the SEI and active Si material through cycling. Through an improved understanding of evolution of SEI and Si active material within the Si wafer model system, mitigation strategies may be designed to extend the lifetime of Si anodes.
A cationic amphiphilic molecule was synthesized and employed to encapsulate Lindqvist ([M{sub 6}O{sub 19}]{sup 2−}) and Keggin polyoxometalates ([SiM{sub 12}O{sub 40}]{sup 4−}, M=Mo, W) to form hybrid molecules through electrostatic interaction. The X-ray diffraction results illustrate that the former hybrids possess lamellar nanostructures in their solid states, while the latter hybrids show a cubic Im3m packing model with low intensities and poor long-range order. These hybrids have clear charge-transfer characters as shown in their deeper colors and UV–vis diffuse reflectance spectra. According to the reported reduction potentials of the POM acceptors and the band gaps deduced from their diffuse reflectance spectra, we have calculated the theoretical values of the lowest unoccupied molecular orbital (LUMO) position similar to the electron affinity (E{sub A}) of solid materials. Such energy level parameters are comparable to those of electroluminescence and electron-transport materials commonly used in organic electroluminescence devices. These organic–polyoxometalate charge-transfer salts have more advantages, such as higher decomposition temperatures, easier film fabrication and better electron affinities, which presumably would be used for electron-transport materials in the area of the electroluminescence. - Graphical abstract: Hybrid molecular materials with charge-transfer characters formed by a positively charged donor L and acceptors of the Lindqvist-type and Keggin-type POMs have lamellar and cubic structures in their solid state. - Highlights: • Charge-transfer salts are obtained by self-assembling POMs with an anthracene cation. • Their energy parameters are comparable to those of optoelectronic materials in OLEDs. • These POM-based hybrids could be applied in the area of optoelectronic devices.
Nickel oxide nanoparticles were synthesized via thermal decomposition of two precursors, the first, a simple nickel malonate and the second, a nickel malonate modified by oleylamine, a surfactant, both having been synthesized by precipitation. While FTIR, TGA and ToF-SIMS were used to characterize the two precursors and to show the presence of oleylamine in the modified precursor, XRD, SEM, TEM and BET were employed to investigate the structure, the morphology and the specific surface area of the decomposition products obtained after pyrolysis. The results showed that the modification of nickel malonate by oleylamine was effective. The XRD results, which showed a cubic structure for the NiO obtained, suggest with SEM an important particle size reduction (at least 54%) when oleylamine was used to modify the nickel malonate precursor. The SEM images also showed a well-defined spherical nanoparticle morphology in both cases, not affected by the presence of oleylamine. The TEM also confirmed the reduction of particle size and their spherical nature but at the same time showed that, in the presence of oleylamine, there was no agglomeration resulting in a more uniform particle size distribution. The specific surface area of the NiO obtained by the oleylamine-modified precursor was 4.7 times larger than that obtained with the regular precursor. This again confirms the particle size reduction. - Highlights: • Nickel malonate precursor has been synthesized by precipitation method. • This precursor was successfully modified by a surfactant (oleylamine). • NiO was identified as the decomposition products of the previous precursors. • Oleylamine has provoked around 54% of particle size reduction of the NiO.
Purification of 4N (99.99%) and 6N (99.9999%) purity Cu rods by hydrogen plasma-arc zone melting was carried out. Weight loss in the 4N and 6N Cu rods as a function of number of zone refined passes revealed a higher rate of impurity removal by vaporization in 4N Cu when compared to 6N Cu. Purification effect was studied by analyzing major impurities like Mg, Si, Ca, Ti, Cr, Ni and Fe by O{sub 2}{sup +} ions and C, O, As, Cl, P and S by Cs{sup +} ion sources using secondary ion mass spectrometry. A remarkable decrease of Si, Ti and Fe impurity concentrations in Cu at x/L = 0.03 after 10 zone passes was observed, but no similar purification effect along the remaining length of the zone refined copper rod was observed. Mg, Se and Ca in the Cu rods were reduced faster by a high evaporation effect due to P{sub i}/P{sub Cu} > 10{sup 2}. On the other hand, removal of O, C, S and Se was expectedly dominated by vaporization in the form of H{sub 2}O, CH{sub 4,} H{sub 2}S, and H{sub 2}Se through thermodynamically favored reactions. The overall segregation rate of the individual impurity elements was decreased with an increase in the purity from 4N to 6N of Cu rods. SIMS analysis of trace impurities was successfully carried out on HPZM Cu for quantitative estimation.
Quenching (AQ) and cryogenic treatments (QC) were conducted on the high-carbon SAE 52100 steel to investigate the mechanical stability of individual retained austenite (RA) by nano-indentation. The cross-sections of indented RA region prepared by focused ion beam (FIB) were examined by using transmission electron microscopy (TEM). For the first time, it was directly observed that some parts of RA grain, closest to the indent, in AQ specimen had transformed into strain-induced martensite (SIM). However, not any pop-in or transformation was detected in the indented QC specimen. This clearly indicates that the mechanical stability of RA in QC seems significantly enhanced, which is mainly attributed to the cryogenic treatment resulting in a higher carbon enrichment of RA compared to that in AQ. Furthermore, a higher load of external stress may need to trigger its martensitic transformation in QC specimen. - Highlights: • Mechanical stability of retained austenite was studied by nano-indentation and TEM. • The strain-induced martensite transformation in RA was observed under applied load. • Cryogenic treatment enhances mechanical stability of RA due to carbon enrichment.
Metal ion in bimetallic nanoparticles has shown vast potential in a variety of applications. In this paper we show the results of physical and chemical investigations of powder Ag/Cu nanoparticles obtained by chemical synthesis. Transmission electron microscopy (TEM) experiment indicated the presence of bimetallic nanoparticles in the agglomerated form. The average size of silver and copper nanoparticles is 17.1(4) nm (Ag) and 28.9(2) nm (Cu) basing on the X-ray diffraction (XRD) data. X-ray photoelectron (XPS) and Raman spectroscopies revealed the existence of metallic silver and copper as well as Cu{sub 2}O and CuO being a part of the nanoparticles. Moreover, UV–Vis spectroscopy showed surface alloy of Ag and Cu while Time of Flight Secondary Ion Mass Spectroscopy (ToF-SIMS) and Energy Dispersive X-ray Spectroscopy (EDX) showed heterogeneously distributed Ag structures placed on spherical Cu nanoparticles. The tests of antibacterial activity show promising killing/inhibiting growth behaviour for Gram positive and Gram negative bacteria. - Highlights: • Ag/Cu nanoparticles were obtained in the powder form. • The average size of nanoparticles is 17.1(4) nm (Ag) and 28.9(2) nm (Cu). • Ag/Cu powder nanoparticle shows promising antibacterial properties.
A Ti–6Mo–6V–5Cr–3Sn–2.5Zr (wt.%) alloy was designed as a new metastable β-Ti alloy. The effect that cold rolling had on the microstructural evolution of the material was investigated via optical microscopy (OM), X-ray diffraction (XRD), electron back-scattered diffraction (EBSD) and transmission electron microscopy (TEM) measurements. A single β phase formed in the alloy after solution treatment at 780 °C for 30 min followed by water quenching. The solution-treated alloy was cold rolled with thickness reductions of 10%, 30%, 50% and 70%, and the hardness values increased as the thickness of the specimen decreased. The textures of the cold rolled specimen were characterized according to the 〈110〉 partial parallel to the rolling direction as the rolling reduction increased. The crystallographic orientation showed principal α-fiber textures for (111)〈110〉 and (112)〈110〉. The cold deformation led to the appearance of martensite α″ phases, particularly stress-induced martensite (SIM) α″ phases. - Highlights: • Effect of cold rolling on new β-typed Ti-6Mo-6V-5Cr-3Sn-2.5Zr alloy was studied. • A single β phase was obtained after solution treatment at 780 °C for 30 min. • α-Fiber textures became dominated with the increase in cold rolling reduction. • A stress-induced α″ martensite was caused by cold rolling.
We present detailed structural and thermoelectric studies of the ternary compound Ce{sub 3}Cu{sub 3}Sb{sub 4}. This material is of interest due to previously reported considerable thermopower above room temperature (∼ 100 μV/K) and low thermal conductivity (2 W/(m K)). Here, we present detailed studies concerning microstructural and thermoelectric data, their variation across the samples and possible explanations for the observed behaviour. We have used X-ray diffraction, scanning electron microscopy (SEM), and time-of-flight secondary ion mass spectrometry (TOF-SIMS) for microstructural analysis. The thermoelectric properties were examined using a physical property measurement system (PPMS). We analyse the impact of the sample quality on the thermoelectric properties. The most unstable parameter is the material resistivity which varies between 1.5 and 15 mΩ cm at room temperature. The properties variability is mainly due to structural defects caused by stresses during material preparation and also due to formation of foreign phases CeCuSb{sub 2} and CeSb. The figure of merit ZT is also strongly dependent on the quality of the sample. The largest value ZT ≈ 0.15 at 400 K is determined for the almost stoichiometric sample with small amounts of a impurity phases. - Highlights: •The Ce{sub 3}Cu{sub 3}Sb{sub 4} has considerable thermoelectric properties and potential for further chemical and/or structural modification. •The control over foreign phases formation is challenging. •The defects arising during arc melting process highly deteriorate ZT of material.
Highlights: • Multilayer TiN/ZrN films were deposited using sequential vacuum-arc deposition of Ti and Zr targets in nitrogen atmosphere; • Several samples were annealed in air at the temperature 700 °C; • First-principles calculations of TiN(111), ZrN(111) structures and TiN(111)/ZrN(111) multilayer were carried out; • All deposited samples were highly polycrystalline with quite large 20–25 nm crystals; • The nanohardness and elastic modulus of non-annealed coatings reached 42 GPa and 348 GPa, respectively; • Deposited coatings demonstrate good wear and oxidation resistance; - Abstract: Nanoscale multilayered TiN/ZrN films were deposited using sequential vacuum-arc deposition of Ti and Zr targets in a nitrogen atmosphere. Studies of film's properties were carried out using various modern methods of analysis, such as XRD, STEM, HRTEM, SIMS combined with results of nanoindentation and tribological tests. To interpret the mechanical properties of the deposited multilayer films first-principles calculations of TiN(111), ZrN(111) structures and TiN(111)/ZrN(111) multilayer were carried out. To study the influence of thermal annealing, several samples were annealed in air at the temperature 700 °C. All deposited samples were highly polycrystalline with quite large 20–25 nm crystals. The crystalline planes were very ordinated and demonstrated an excellent coordinated growth. The nanohardness and elastic modulus of non-annealed coatings reached 42 GPa and 348 GPa, respectively. Annealing in air at the temperature 700 °C led to partial oxidation of the multilayered coatings, however hardness of the non-oxidized part of the coatings remained as high, as for initial coatings. All deposited coatings demonstrate good wear resistance.
Highlights: • Ni-rich/Ti-rich bi-layer thin film was deposited on Si by using DC magnetron sputtering. • The bi-layer exhibits the gradient structure and mechanical properties through the thickness. • The bi-layer shows intrinsic two-way shape memory effect due to functionally graded structure. • The intrinsic two-way shape memory effect was confirmed by finite element simulation. - Abstract: In this research, the gradient structure and mechanical properties of an austenitic/martensitic (Ni{sub 50.8}Ti/Ni{sub 45}TiCu{sub 5} (at.%)) bi-layer thin film was investigated. The bi-layer was deposited on a Si substrate using DC magnetron sputtering. After crystallization of the film at 773 K for 60 min, the microstructure and mechanical properties of the bi-layer thin film were characterized using X-ray diffraction (XRD), transmission electron microscopy (STEM and HRTEM) and nanoindentation, respectively. The diffraction pattern illustrated that the crystallized bi-layer was combined of martensitic and austenitic layers while secondary ion mass spectroscopy (SIMS) and high resolution transmission electron microscopy analysis demonstrated the existence of a compositional gradient through the thickness and residual strain in the interface of the bi-layer, respectively. Furthermore, the compositional gradient in the bi-layer led to gradual variations in the structure, hardness and Young's modulus through the thickness of the bi-layer. The intrinsic two-way shape memory effect due to its functionally graded structure and the induced stress was confirmed by experimental test and finite element simulation.
Highlights: • Ti-12Mo-5Zr alloy exhibits excellent combination of improved yielding strength (>650 MPa), high ductility (uniform elongation ≈30%) and work-hardening behaviour. • The superior performances arise from the synergic effects between phase transformation induced plasticity and twinning induced plasticity. • The ‘d-electron’ alloy design approach in Ti-12Mo-5Zr alloy, i.e. Zr substitution to Ti, validates the feasibility of yielding stress improvement of TWIP/TRIP titanium alloys. - Abstract: In this paper, a novel ternary β-metastable titanium alloy, Ti-12Mo-5Zr (wt%), was designed based on the “d-electron” alloy design theory. The Ti-12Mo-5Zr alloy displays excellent combination of improved yielding stress (>650 MPa), high ductility (uniform elongation ≈30%) and work-hardening behaviour. The detailed microstructural analysis indicates that the superior performances arise from the synergic effects between phase transformation induced plasticity (TRIP) and twinning induced plasticity (TWIP). Conforming to the design strategy, the improvement of mechanical performance results from the addition of Zr alloying element in substituting Ti, attributing to solution hardening effect and the increasing of critical resolved shear stress (CRSS) of stress induced martensitic transformation (SIM α″).
Highlights: • The 3.05Mo steel has higher resistance to strain-induced transformation than the 0.28Mo steel. • The increased Mo content affects the grain growth of austenite and ferrite due to the effects of segregation and anchoring. • At high annealing temperatures, this Mo retarding effect is weakened. • The suppression of γ-fiber development in the ferrite texture is associated with the increased Mo content. • High amounts of Mo generate unfavorable conditions for the formation of CSL boundaries. - Abstract: The microstructure and texture evolution of duplex stainless steels with different molybdenum contents were studied. For this purpose, hot-rolled 2205 and 2304 samples were solution-annealed at 1100 °C for 1800 s and then cold-rolled to a 75% thickness reduction. This was followed by an isothermal annealing at 900 and 1100 °C for 180 s. The EBSD technique was used to determine the phase ratio, crystallographic texture, and microstructural characteristics. The hot-rolled steel had a work hardened microstructure and the samples submitted to intermediate annealing presented mainly deformation-free grains. Cold rolling resulted in a substantial reduction in the phase spacing with the formation of the strain-induced α′-martensite (SIM) from the metastable austenite. After annealing at 900 °C, the ferrite grains retained the elongated shape of the cold-rolled condition and the primary recrystallization progressed in the austenite phase. Increasing the Mo content increased the resistance to strain-induced martensitic transformation and inhibited the grain growth of austenite phase during annealing at 900 °C. Increasing annealing temperature to 1100 °C promoted the coarsening of both bcc and fcc structures with the formation of annealing twins in the austenitic grains. The recrystallization kinetics and subsequent grain growth occur earlier in ferrite than in austenite phase. Differences in Mo content did not significantly alter the evolution of austenite texture, whereas in the ferrite phase the increase in Mo content suppressed the γ-fiber development. Oriented nucleation was the predominant mechanism observed during the recrystallization of ferritic grains in the 2205 samples. The development of ∑19a boundaries was associated with the selected growth of {554}<225>{sub α} grains in the annealed 2304 samples. Annealing twins were associated with the formation of Σ3 boundaries after the heat treatments. Grain coarsening resulted in a larger fraction of the special boundaries in ferrite phase but inhibited the CSL formation in the austenite phase.
Graphical abstract: Synthesis of Mn{sub 2−x}Nd{sub x}O{sub 3} with mixed morphology -- Abstract: Neodymium (Nd) ions were substituted for manganese in the crystal lattice of synthetic Mn{sub 2}O{sub 3}, via oxidation of Mn(NO{sub 3}){sub 2} in basic solution at room temperature. Doping of Nd into the lattice structure of Mn{sub 2}O{sub 3} has been reported for the first time, which resulted in materials with new composition, morphology and optical properties. The synthesized materials were characterized by XRD, SEM, TEM, HRTEM, XPS and TOF-SIMS. Light (2.6%) Nd doping resulted in a mixture of rods, plates and small sheets, while heavy (8.9%) Nd doping resulted in rods, large sheets and large single crystals. The effect of structural doping of Nd ions into Mn{sub 2}O{sub 3} resulted in a red shift in the absorbance.
Highlights: • In- and Sn-based MIC phenomenon on amorphous (α)-Ge is newly reported. • The In- and Sn-MIC phenomenon respectively started at 250 °C and 400 °C. • The Sn-MIC process presents higher sheet resistance and bigger crystal grains. - Abstract: In this paper, metal-induced crystallization (MIC) phenomenon on α-Ge by indium (In) and tin (Sn) are thoroughly investigated. In- and Sn-MIC process respectively started at 250 °C and 400 °C. Compared to the previously reported MIC samples including In-MIC, Sn-MIC process presented higher sheet resistance (similar to that of SPC) and bigger crystal grains above 50 nm (slightly smaller than that of SPC). According to SIMS analysis, Sn atoms diffused more slowly into Ge than In at 400 °C, providing lower density of heterogeneous nuclei induced by metals and consequently larger crystal grains.
Highlights: • SIMS analysis confirmed the doping of Er into the In{sub 2}O{sub 3} TF. • I–V loop analysis gives reduced current memory window for In{sub 2}O{sub 3}:Er TF based device. • High ideality factor was determined at low temperature and explained. • Defect related photoconductivity was confirmed from low temperature measurement. • 10 K temporal response of the Au/In{sub 2}O{sub 3}:Er/Si confirmed removal of oxygen defects. - Abstract: Erbium doped Indium Oxide (In{sub 2}O{sub 3}:Er) thin films (TFs) were synthesised by spin-on technique. Secondary Ion Mass Spectrometry confirmed that Er is incorporated into the In{sub 2}O{sub 3} lattice and formed an In-O-Er layer. The current–voltage loop produced a lower loop current window of ∼3.6 × 10{sup −4} A for In{sub 2}O{sub 3}:Er TF based devices. The Au/In{sub 2}O{sub 3}:Er/Si Schottky devices have lower ideality factor (∼6) and higher barrier height (∼0.63 eV) at 300 K than Au/In{sub 2}O{sub 3}/Si control samples. A blue shift in the main band-gap (∼50 nm) was calculated for In{sub 2}O{sub 3}:Er TFs from 10 K photoresponse. The Au/In{sub 2}O{sub 3}:Er/Si samples show higher photosensitivity in the temperature range 10 K–300 K and maximum (∼15 times) in the UV region at 10 K as compared to the Au/In{sub 2}O{sub 3}/Si devices. In addition, the Au/In{sub 2}O{sub 3}:Er/Si devices have better UV to visible cut-off ratio (∼3 times). Excellent temporal responses were recorded for Au/In{sub 2}O{sub 3}:Er/Si in the UV region as compared to Au/In{sub 2}O{sub 3}/Si.