SEARCH · Engineering Papers

Results for “STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Micromechanics analysis of space simulated thermal stresses in composites. I - Theory and unidirectional laminates. II - Multidirectional laminates and failure predictions

A micromechanics analysis is used to study the effects of constituent properties on thermally induced stresses in continuous fiber reinforced composites. A finite element formulation is described, and results are presented for unidirectional carbon/epoxy laminates. It is shown that significant stresses develop in composites exposed to thermal excursions typical of spacecraft operating environments and that the fiber thermoelastic properties have a minimal effect on the magnitude of these stresses. The finite element micromechanics analysis is then extended to the study of multidirectional laminates using a simple global/local formulation. Damage initiation predictions are compared with experimental data, and factors controlling the initiation of damage are identified. Ways of improving the durability of composites are discussed.

Bowles, David E.↗

NASA NTRS1991

Fiber Creep Evaluation by Stress Relaxation Measurements

A simple bend stress relaxation (BSR) test has been used to measure the creep related properties of a chemically vapor-deposited SiC fiber. Time, temperature, and strain dependent BSR data were analyzed to ascertain the ability of the stress relaxation results to predict tensile creep as a function of the same parameters. The predictions compared very well to actual creep data obtained by axial measurements, indicating that the BSR test could be used for determining both creep and stress relaxation of polycrystalline ceramic fibers under tensile loading.

Morscher, Gregory N.↗

NASA NTRS1991

Advanced stress analysis methods applicable to turbine engine structures

The following tasks on the study of advanced stress analysis methods applicable to turbine engine structures are described: (1) constructions of special elements which contain traction-free circular boundaries; (2) formulation of new version of mixed variational principles and new version of hybrid stress elements; (3) establishment of methods for suppression of kinematic deformation modes; (4) construction of semiLoof plate and shell elements by assumed stress hybrid method; and (5) elastic-plastic analysis by viscoplasticity theory using the mechanical subelement model.

Pian, Theodore H. H.↗

NASA NTRS1991

Using probabilistic analysis to assess the reliability of predicted SRB aft-skirt stresses

Probabilistic failure analysis is a tool to predict the reliability of a part or system. Probabalistic techniques were used to predict critical stresses which occur in the solid rocket booster aft-skirt during main engine buildup, immediately prior to lift-off. More than any other hold down post (HDP) load component, the Z loads are sensitive to variations in strains and calibration constants. Also, predicted aft-skirt stresses are strongly affected by HDP load variations. Therefore, the instrumented HDP are not effective load transducers for Z loads, and, when used with aft skirt stress indicator equations, yield estimates with large uncertainty. Monte Carlo simulation proved to be a straight forward way of studying the overlapping effects of multiple parameters on predicted equipment performance. An advantage of probabilistic analysis is the degree of uncertainty of each parameter as stated explicitly by its probability distribution. It was noted, however, that the choice of parameter distribution had a large effect on the simulation results. Many times these distributions must be assumed. The engineer who is designing the part should be responsible for the choice of parameter distribution.

Richardson, James A.↗

NASA NTRS1991

Advanced development of the boundary element method for elastic and inelastic thermal stress analysis

The focus of this dissertation is on advanced development of the boundary element method for elastic and inelastic thermal stress analysis. New formulations for the treatment of body forces and nonlinear effects are derived. These formulations, which are based on particular integral theory, eliminate the need for volume integrals or extra surface integrals to account for these effects. The formulations are presented for axisymmetric, two and three dimensional analysis. Also in this dissertation, two dimensional and axisymmetric formulations for elastic and inelastic, inhomogeneous stress analysis are introduced. The derivatives account for inhomogeneities due to spatially dependent material parameters, and thermally induced inhomogeneities. The nonlinear formulation of the present work are based on an incremental initial stress approach. Two inelastic solutions algorithms are implemented: an iterative; and a variable stiffness type approach. The Von Mises yield criterion with variable hardening and the associated flow rules are adopted in these algorithms. All formulations are implemented in a general purpose, multi-region computer code with the capability of local definition of boundary conditions. Quadratic, isoparametric shape functions are used to model the geometry and field variables of the boundary (and domain) of the problem. The multi-region implementation permits a body to be modeled in substructured parts, thus dramatically reducing the cost of analysis. Furthermore, it allows a body consisting of regions of different (homogeneous) material to be studied. To test the program, results obtained for simple test cases are checked against their analytic solutions. Thereafter, a range of problems of practical interest are analyzed. In addition to displacement and traction loads, problems with body forces due to self-weight, centrifugal, and thermal loads are considered.

Henry, Donald P., Jr.↗

NASA NTRS1992

Transient thermal stress recovery for structural models

A method for computing transient thermal stress vectors from temperature vectors is described. The three step procedure involves the use of NASTRAN to generate an influence coefficient matrix which relates temperatures to stresses in the structural model. The transient thermal stresses are then recovered and sorted for maximum and minimum values. Verification data for the procedure is also provided.

Walls, William↗

NASA NTRS1992

Effect of type of load on stress analysis of thin-walled ducts

The standard procedure for qualifying the design of duct (pipe) systems in the Space Shuttle Main Engine (SSME) has been fairly well defined. However, since pipe elbows are quite common and important in the SSME duct systems, a clear understanding of the detailed stress profile of the components is necessary for accurate structural and life assessments. This study was initiated to predict the stress profile at/near the tangent point along the cross section of the duct under various types of loads. Also, this study was further extended to understand the stiffening effect on stresses due to pressure at the tangent point. The intention of this study was to identify the importance of selecting proper locations for mounting strain gauges and to utilize the obtained results to anchor dynamic models for accurate structural and life assessments of the SSME ducts under a dynamic environment. The finite element method was utilized in this study.

Min, J. B.↗

NASA NTRS1991

Stress analysis of Tellus Regio, Venus, based on gravity and topography - Comparison with Venera 15/16 radar images

The tectonics of the Tellus Region highland on Venus is examined using the altimetry and gravity data collected by Pioneer Venus, which were incorporated into a thin elastic shell model to calculate both the global (long-wavelength) and the regional (short-wavelength) stresses for various assumed values of crust, lithosphere, and mantle thickness and modes of compensation. The resultant stress fields were compared to the surface morphology observed in the Venera 15/16 radar images and interpreted in terms of stress history of Tellus Regio. The best fitting parameters were found to be consistent with minor amounts of lithospheric flexure being necessary to produce the observed surface features of this region.

Williams, David R.↗

NASA NTRS1991

Residual thermal strains and stresses in nickel aluminide matrix composites

Thermally induced residual strains and stresses developed during postfabrication cooling in Saphikon/NiAl and tungsten/NiAl high-temperature composites are investigated through three-dimensional elastoplastic finite-element analyses. Average axial and transverse strains in the matrix are found to be tensile and compressive, respectively, and similar for both Saphikon and W-fiber-reinforced NiAl composites. It is suggested that the residual matrix stresses and strains are controlled more by the low-matrix yield stress than by the fiber/matrix expansion mismatch. Residual thermal strains in the matrix of these composites are measured by using a neutron-diffraction technique; the measured axial and transverse strains in the matrix are found to be in agreement with the computed values.

Saigal, A.↗

NASA NTRS1991

The dependence of wind stress on wave height and wind speed

Three near-neutral boundary layer data sets were investigated with the aim of finding a dependence of wind stress on both wind speed and significant wave height. The data set most representative of open-ocean wave height, wind speed, and momentum flux conditions, was selected and analyzed by means of the least-squares method to produce a new parameterization for the wind stress as a function of both wind speed and significant wave height. This study shows that the wind stress, and consequently the drag coefficient, decreases with increasing wave height for a fixed wind speed. The study also shows that the curvature of the wind profile decreases with increasing wave height and that the C(DN) = A + BU-bar(10) form for the drag coefficient parameterization is inadequate. A drag coefficient that applies to both smooth and rough flows is proposed. These results are more applicable for open-ocean deep-water conditions and less applicable for sheltered, closed, shallow water sites.

Blake, Reginald A.↗

NASA NTRS1992

Stress versus temperature dependence of activation energies for creep

The activation energy for creep at low stresses and elevated temperatures is associated with lattice diffusion, where the rate controlling mechanism for deformation is dislocation climb. At higher stresses and intermediate temperatures, the rate controlling mechanism changes from dislocation climb to obstacle-controlled dislocation glide. Along with this change in deformation mechanism occurs a change in the activation energy. When the rate controlling mechanism for deformation is obstacle-controlled dislocation glide, it is shown that a temperature-dependent Gibbs free energy does better than a stress-dependent Gibbs free energy in correlating steady-state creep data for both copper and LiF-22mol percent CaF2 hypereutectic salt.

Freed, A. D.↗

NASA NTRS1992

Fluid stress disturbance activated by gravity jitters induced slosh waves in microgravity

A full scale Gravity Probe-B (GP-B) Spacecraft propellant dewar tank subjected to various frequencies of gravity jitter have been investigated. Excitation of slosh waves induced by gravity jitter are simulated. Results show that fluid stress distribution exerted on the walls of the rotating dewar are closely related to the characteristics of slosh waves excited on the liquid-vapor interface in the rotating dewar tank. Slosh wave excitations shift the fluid mass distribution in the dewar tank which impose time dependent variations in GP-B Spacecraft moment of inertia, angular momentum, and torque produced by imbalance fluid stresses. This can provide a set of data leading toward the control of spacecraft imbalance caused by the uneven fluid stress distribution from slosh waves.

Hung, R. J.↗

NASA NTRS1991

Does a threshold stress for creep exist in HfC-dispersed NiAl?

Recently it was proposed (Jha et al., 1989; Whittenberger et al., 1990) on the basis of constant velocity testing at 1300 K that dispersion strengthened NiAl composites containing about 4 wt pct HfC possess threshold stresses for creep. Further, 1300 K compression testing has been conducted on NiAl+4HfC, and diametrically opposite behavior has been found: for constant load creep tests a normal power law behavior was observed. However, additional constant velocity testing still indicates that the flow stress is essentially independent of strain rate below 10 exp -6/s. Examination of NiAl+4.3HfC specimens deformed under constant velocity conditions revealed that the original hot extruded small grain structure could be converted to large, elongated grains during testing. Such a transformation appears to be responsible for the apparent threshold stress behavior in HfC dispersed NiAl.

Whittenberger, J. D.↗

NASA NTRS1992

Anodized aluminum coatings for thermal control. I - Coating process and stresses

Anodized aluminum is a candidate material for use as a thermal radiator surface on Space Station Freedom. Here, results of measurements of coating stress at room temperature are presented. The effects of coating process conditions and also subsequent exposure to different humidities, from above ambient to vacuum, are reported. The most important observation with regard to space applications is that the coating stress is very dependent on humidity, changing from compressive at ambient humidity to strongly tensile in 10 exp -6 torr vacuum. The increase in stress is accompanied by loss of water from the coating, and the process is reversible.

Alwitt, R. S.↗

NASA NTRS1991

Deformation and stress response of composite laminated shells under internal pressure

This paper presents a theoretical study of the response of filament wound composite shells under internal pressure. Each layer of the material is generally cylindrically anisotropic. By using cylindrically anisotropic elasticity field equations and Lekhnitskii's stress functions, a system of sixth-order ordinary differential equations is obtained. The general expressions for the stresses and displacements in the laminated composite shells under internal pressure are discussed. Two composite systems, graphite/epoxy and glass/epoxy, are selected to demonstrate the influence of degree of material anisotropy and fiber orientations on the axial and induced twisting deformation. Stress distributions of (45/-45)s symmetric angle-ply fiber-reinforced laminated shells are shown to illustrate the effect of radius-to-thickness ratio.

Yuan, F. G.↗

NASA NTRS1992

Stress reduction in an isotropic plate with a hole by applied induced strains

Recently there has been much interest in adaptive structures that can respond to a varying environment by changing their properties. Shape memory alloys and piezoelectric materials can be used as induced strain actuators to reduce stresses in the regions of stress concentration. The objective of the work was to find the maximum possible reduction in the stress concentration factor in an isotropic plate with a hole by applying induced strains in a small area near the hole. Induced strains were simulated by thermal expansion.

Sensharma, Pradeep K.↗

NASA NTRS1991

Combined effect of matrix cracking and stress-free edge on delamination

The effect of the stress-free edge on the growth of local delaminations initiating from a matrix crack in (O sub 2/90 sub 4) sub s and (+/- 45.90 sub 4) sub s glass epoxy laminates is investigated using 3D finite element analysis. The presence of high interlaminar normal stresses at the intersection (corner) of the matrix crack with the stress-free edge, suggests that a mode I delamination may initiate at the corners. The strain energy release rates (G) were calculated by modeling a uniform through-width delamination and two inclined delaminations at 10.6 deg and 45 deg to the matrix crack. All components of G have high values near the free edges. The mode I component of G is high at small delamination length and becomes zero for a delamination length of one-ply thickness. The total G values near the free edge agreed well with previously derived closed form solution. The quasi-3D solutions agreed well with the 3D interior solutions.

Salpekar, Satish A.↗

NASA NTRS1992

Spacecraft dynamical distribution of fluid stresses activated by gravity-jitter-induced slosh waves

The dynamical behavior of fluids, in particular the effect of surface tension on partially filled rotating fluids (cryogenic liquid helium and helium vapor) in a full-scale Gravity Probe-B Spacecraft propellant Dewar tank imposed by various frequencies of gravity jitters, has been investigated. Fluid stress distribution, caused by the excitation of slosh waves and their associated large-amplitude disturbances on the liquid-vapor interface, exerted on the outer and inner walls of a rotating Dewar container also has been investigated. Results show that fluid stress distributions near the outer and inner walls of the rotating Dewar are closely related to the characteristics of slosh waves excited on the liquid-vapor interface in the rotating Dewar tank. This can provide a useful tool for managing spacecraft dynamic control leading toward the control of spacecraft imbalance caused by the uneven fluid stress distribution due to slosh wave excitations at the interface between liquid and vapor propellants.

Hung, R. J.↗