Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Rocket”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

The historical contribution of solid rocket motors to the one centimeter debris population

The measured small particle population in earth orbit contains cm-sized objects that are not accounted for by breakup fragments. It was proposed that slag ejection during solid rocket motor burn is a contributor to this population. The direct evidence for such slag ejection follows from: observations of the exhausts of vehicles in flight, and engineering data from static firings. A source model is presented to account for the contribution of slag expulsion from solid rocket motors to the debris population. The mass and velocity distribution of the slag effluents are taken into account and used as a source term in the debris environment model. The model is based on the available observation data and on models for slag development and ejection.

Jackson, Albert↗
NASA NTRS1998

Comparison of High Aspect Ratio Cooling Channel Designs for a Rocket Combustion Chamber with Development of an Optimized Design

An analytical investigation on the effect of high aspect ratio (height/width) cooling channels, considering different coolant channel designs, on hot-gas-side wall temperature and coolant pressure drop for a liquid hydrogen cooled rocket combustion chamber, was performed. Coolant channel design elements considered were: length of combustion chamber in which high aspect ratio cooling was applied, number of coolant channels, and coolant channel shape. Seven coolant channel designs were investigated using a coupling of the Rocket Thermal Evaluation code and the Two-Dimensional Kinetics code. Initially, each coolant channel design was developed, without consideration for fabrication, to reduce the hot-gas-side wall temperature from a given conventional cooling channel baseline. These designs produced hot-gas-side wall temperature reductions up to 22 percent, with coolant pressure drop increases as low as 7.5 percent from the baseline. Fabrication constraints for milled channels were applied to the seven designs. These produced hot-gas-side wall temperature reductions of up to 20 percent, with coolant pressure drop increases as low as 2 percent. Using high aspect ratio cooling channels for the entire length of the combustion chamber had no additional benefit on hot-gas-side wall temperature over using high aspect ratio cooling channels only in the throat region, but increased coolant pressure drop 33 percent. Independent of coolant channel shape, high aspect ratio cooling was able to reduce the hot-gas-side wall temperature by at least 8 percent, with as low as a 2 percent increase in coolant pressure drop. ne design with the highest overall benefit to hot-gas-side wall temperature and minimal coolant pressure drop increase was the design which used bifurcated cooling channels and high aspect ratio cooling in the throat region. An optimized bifurcated high aspect ratio cooling channel design was developed which reduced the hot-gas-side wall temperature by 18 percent and reduced the coolant pressure drop by 4 percent. Reductions of coolant mass flow rate of up to 50 percent were possible before the hot-gas-side wall temperature reached that of the baseline. These mass flow rate reductions produced coolant pressure drops of up to 57 percent.

Wadel, Mary F.↗
NASA NTRS1998

Thruster Injector Faceplate Testing in Support of the Aerojet Rocket-Based Combined Cycle (RBCC) Concept

To satisfy RBCC rocket thruster requirements of high performance and a minimum amount of free hydrogen at plume boundary, a new impinging injector element using gaseous hydrogen and gaseous oxygen as the propellants has been designed. Analysis has shown that this injector design has potential to provide a high specific impulse (Isp) while minimizing the amount of free hydrogen that is available to be burned with incoming secondary flow. Past studies and test programs have shown that gas/gas-impinging elements typically result in high injector face temperatures due to combustion occurring close to the face. Since this design is new, there is no hot fire experience with this element. Objectives of this test program were to gain experience and hot fire test data on this new rocket thruster element design and injector faceplate pattern. Twenty-two hot fire tests were run with maximum mixture ratio (MR) and chamber pressure (Pc) obtained at 7.25 and 1,822 psia, respectively. Post-test scanning microscope (SEM) images show only slight faceplate erosion during testing. This injector element design performed well and can be operated at design conditions: (1) Pc of 2,000 psia and MR of 7.0 and (2) Pc of 1,000 psia and MR of 5.0.

Fazah, M. M.↗
NASA NTRS1996

Spray Diagnostics in Rocket Engines Using Phase Doppler Analyzer

Characteristics such as drop velocity, drop size, number density, volume flow rate, volume flux, and evaporation rate of the fuel spray in a rocket engine are directly related to engine performance. Several studies of shear coaxial atomization have been done in the past. However, additional work related to sprays at supercritical and transcritical conditions would be useful. The author undertook a study of the feasibility of using a phase Doppler particle analyzer (PDPA) for spray measurements in rocket engines as a part of the Summer Faculty Fellowship Program at the NASA Marshall Space Flight Center. The PDPA is a single particle counter (SPC) system based on light scattering from spherical particles. The PDPA instrument is based on refractive and reflective scattering as opposed to other instruments based on diffractive scattering. The main advantage of the PDPA instrument is its ability to provide point-wise information. The following sections describe the principle of operation of the PDPA system and the data obtained using a PDPA instrument in a spray formed by a commercially available fuel injection nozzle.

Isaac, Kakkattukuzhy M.↗
NASA NTRS1961

Ignition of Hydrogen-Oxygen Rocket Combustor with Chlorine Trifluoride and Triethylaluminum

Ignition of a nominal-125-pound-thrust cold (2000 R) gaseous-hydrogen - liquid-oxygen rocket combustor with chlorine trifluoride (hypergolic with hydrogen) and triethylaluminum (hypergolic with oxygen) resulted in consistently smooth starting transients for a wide range of combustor operating conditions. The combustor exhaust nozzle discharged into air at ambient conditions. Each starting transient consisted of the following sequence of events: injection of the lead main propellant, injection of the igniter chemical, ignition of these two chemicals, injection of the second main propellant, ignition of the two main propellants, increase in chamber pressure to its terminal value, and cutoff of igniter-chemical flow. Smooth ignition was obtained with an ignition delay of less than 100 milliseconds for the reaction of the lead propellant with the igniter chemical using approximately 0.5 cubic inch (0-038 lb) of chlorine trifluoride or 1.0 cubic inch (0-031 lb) of triethylaluminum. These quantities of igniter chemical were sufficient to ignite a 20-percent-fuel hydrogen-oxygen mixture with a delay time of less than 15 milliseconds. Test results indicated that a simple, light weight chemical ignition system for hydrogen-oxygen rocket engines may be possible.

Gregory, John W.↗
NASA NTRS1960

Experimental Performance of Area Ratio 200, 25 and 8 Nozzles on JP-4 Fuel and Liquid Oxygen Rocket Engine

The performance of an area ratio 200 bell-shaped nozzle, an area ratio 25 bell-shaped nozzle, and an area ratio 8 conic nozzle on a JP-4 fuel and liquid-oxygen rocket engine has been determined. Tests were conducted using a nominal 4000-pound-thrust rocket in the Lewis 10- by 10-foot supersonic tunnel, which provided the altitude environment needed for fully expanded nozzle flow. The area ratio 200 nozzle had a vacuum thrust coefficient of 1.96, compared with 1.82 and 1.70 for the area ratio 25 and 8 nozzles, respectively. These values are approximately equal to those for theoretical frozen expansion. The measured value of vacuum specific impulse for the area ratio 200 nozzle was 317 seconds for a combustion-chamber characteristic velocity of 5200 feet per second. The vacuum-specific-impulse increase for the area-ratio increase from 8 to 200 was 46 seconds.

Lovell, J. Calvin↗
NASA NTRS1959

Experimental and Analytical Study of Rolling-Velocity Amplification during the Thrusting Process for Two 10-Inch-Diameter Spherical Rocket Motors in Free Flight

Two 10-inch-diameter spherical rocket motors have been flight tested at the NASA Wallops Station. These tests were conducted to measure "spin-up" or amplification of the spinning velocity of the motor during the thrusting process due to internal swirling of the exhaust gases. Model 1, a heavy-wall motor, experienced an increase in spin rate during thrusting of about 10 percent, whereas model 2, a flight-type motor with a lightweight motor case, experienced an increase of about 19 percent. The propellant weight and geometry were the same for both motors. A simple relationship for "spin-up" which satisfies these measured results is reported herein. Both models were spin stabilized throughout their flights. A theoretical method of predicting spin-up was derived and used to extend the measured 10-inch-motor results to spherical rocket motors of other sizes having a similar propellant geometry. This method is presented and its predictions are shown to compare favorably with the measured flight results.

Martz, C. William↗
NASA NTRS1961

Annular Internal-External-Expansion Rocket Nozzles for Large Booster Applications

For large-thrust booster applications, annular rocket nozzles employing both internal and external expansion are investigated. In these nozzles, free-stream air flows through the center as well as around the outside of the exiting jet. Flaps for deflecting the rocket exhaust are incorporated on the external-expansion surface for thrust-vector control. In order to define nozzle off-design performance, thrust vectoring effectiveness, and external stream effects, an experimental investigation was conducted on two annular nozzles with area ratios of 15 and 25 at Mach 0, 2, and 3 in the Lewis 10- by 10-foot wind tunnel. Air, pressurized to 600 pounds per square inch absolute, was used to simulate the exhaust flow. For a nozzle-pressure-ratio range of 40 to 1000, the ratio of actual to ideal thrust was essentially constant at 0.98 for both nozzles. Compared with conventional convergent-divergent configurations on hypothetical boost missions, the performance gains of the annular nozzle could yield significant orbital payload increases (possibly 8 to 17 percent). A single flap on the external-expansion surface of the area-ratio-25 annular nozzle produced a side force equal to 4 percent of the axial force with no measurable loss in axial thrust.

Connors, James F.↗
NASA NTRS1961

Determination of Local Experimental Heat-Transfer Coefficients on Combustion Side of an Ammonia-Oxygen Rocket

Local experimental heat-transfer coefficients were measured in the chamber and throat of a 2400-pound-thrust ammonia-oxygen rocket engine with a nominal chamber pressure of 600 pounds per square inch absolute. Three injector configurations were used. The rocket engine was run over a range of oxidant-fuel ratio and chamber pressure. The injector that achieved the best performance also produced the highest rates of heat flux at design conditions. The heat-transfer data from the best-performing injector agreed well with the simplified equation developed by Bartz at the throat region. A large spread of data was observed for the chamber. This spread was attributed generally to the variations of combustion processes. The spread was least evident, however, with the best-performing injector.

Liebert, Curt H.↗
NASA NTRS1960

Bonded and Sealed External Insulations for Liquid-Hydrogen-Fueled Rocket Tanks During Atmospheric Flight

Several currently available nonmetallic insulation materials that may be bonded onto liquid-hydrogen tanks and sealed against air penetration into the insulation have been investigated for application to rockets and spacecraft. Experimental data were obtained on the thermal conductivities of various materials in the cryogenic temperature range, as well as on the structural integrity and ablation characteristics of these materials at high temperatures occasioned by aerodynamic heating during atmospheric escape. Of the materials tested, commercial corkboard has the best overall properties for the specific requirements imposed during atmospheric flight of a high-acceleration rocket vehicle.

Gray, V. H.↗
NASA NTRS1960

Flight Performance of a Spin-Stabilized 20-Inch-Diameter Solid-Propellant Spherical Rocket Motor

A successful flight test of a spin-stabilized 20-inch-diameter solid-propellant rocket motor having a propellant mass fraction of 0.92 has been made. The motor was fired at altitude after being boosted by a three-stage test vehicle. Analysis of the data indicates that a total impulse of 44,243 pound-second with a propellant specific impulse of approximately 185 was achieved over a total action time of about 12 seconds. These results are shown to be in excellent agreement with data from ground static firing tests of these motors. The spherical rocket motor with an 11-pound payload attained a velocity of 15,620 feet per second (m = 16.7) with an incremental velocity increase for the spherical motor stage of 12,120 feet per second.

Levine, Jack↗
NASA NTRS1960

Experimental Evaluation of Rocket Exhaust Diffusers for Altitude Simulation

An experimental investigation of exhaust diffusers has been conducted to evaluate various methods of minimizing the overall pressure ratio (from chamber to ambient pressure) required to establish and maintain full expansion of the nozzle flow (altitude simulation). Exhaust-diffuser configurations investigated were (1) cylindrical diffusers, (2) diffusers with contraction, and (3) diffusers including a right-angle turn. Cylindrical diffusers were evaluated with primary nozzles of various area ratios and types, as well as two clustered configurations; the other diffusers were evaluated with individual nozzles of constant area ratio and varied type. Air was the working fluid, except for two check points obtained with JP-4 fuel and liquid-oxygen rocket engines and cylindrical diffusers. The minimum length-diameter ratio of cylindrical diffusers was about 6 for minimum pressure-ratio requirements. With cylindrical diffusers of adequate length, the pressure-ratio requirements were primarily a function of the ratio of diffuser to nozzle-throat areas and were essentially independent of primary-nozzle type (including two clustered configurations) or area ratio. The two check points obtained with rocket engines indicated the pressure-ratio requirements at given ratios of diffuser to nozzle-throat areas were lowered, as compared with the requirements with air, as a result of the reduced ratio of specific heats. The minimum length-diameter ratio of the contraction throat of convergent-divergent diffusers was also about 6 for minimum pressure-ratio requirements. With adequate contraction-throat length, the pressure-ratio requirements of such diffusers were appreciably below those of comparable cylindrical diffusers when used with conical and cutoff-isentropic nozzles, but not when used with a bell nozzle. Minimum pressure-ratio requirements of a diffuser including a simple long-radius right-angle turn at maximum diffuser area, obtained with the center of radius of the turn a minimum of 2 diffuser diameters downstream of the nozzle exit, were not appreciably above those of a comparable optimum cylindrical diffuser. A diffuser including a long-radius right-angle turn at a contraction minimum area had somewhat lower pressure-ratio requirements than the aforementioned simple turn.

Sivo, Joseph N.↗
NASA NTRS1959

Analysis of Flow-System Starting Dynamics of Turbopump-Fed Liquid-Propellant Rocket

Two rocket configurations with turbopump drive were investigated analytically. In one configuration the inlet pressure to the turbine was fixed at the design value. The second configuration employed a "bootstrap" technique for supplying energy to the turbine. An injector was the chief resistance between the pump and the rocket combustion chamber. From the analysis two parameters were developed from which the speed response time of the turbopump, the flow response time, and the maximum dynamic line loss could be evaluated. These parameters were functions of turbopump moment of inertia, design performance of the turbine, and flow-system geometry. The moment of inertia of the turbopump and the ratio of turbine torque at zero speed to design torque had the most influence on the starting dynamics of the flow system. These parameters were also applicable to the bootstrap configuration as long as the inlet pressure to the turbine exceeded half the design value.

Krebs, Richard P.↗
NASA NTRS1998

Feasibility Investigation on the Development of a Structural Damage Diagnostic and Monitoring System for Rocket Engines

The research activity for this project is mainly to investigate the necessity and feasibility to develop a structural health monitoring system for rocket engines, and to carry out a research plan for further development of the system. More than one hundred technical papers have been searched and reviewed during the period. We concluded after this investigation that adding a new module in NASA's existing automated diagnostic system to monitor the healthy condition of rocket engine structures is a crucial task, and it's possible to develop such a system based upon the vibrational-based nondestructive damage assessment techniques. A number of such techniques have been introduced. Their advantages and disadvantages are also discussed. A global research plan has been figured out. As the first step of the overall research plan, a proposal for the next fiscal year has been submitted.

Shen, Ji Y.↗
NASA NTRS1997

Gas Core Nuclear Rocket Feasibility Project

The next giant leap for mankind will be the human exploration of Mars. Almost certainly within the next thirty years, a human crew will brave the isolation, the radiation, and the lack of gravity to walk on and explore the Red planet. However, because the mission distances and duration will be hundreds of times greater than the lunar missions, a human crew will face much greater obstacles and a higher risk than those experienced during the Apollo program. A single solution to many of these obstacles is to dramatically decrease the mission duration by developing a high performance propulsion system. The gas core nuclear rocket (GCNR) has the potential to be such a system. The gas core concept relies on the use of fluid dynamic forces to create and maintain a vortex. The vortex is composed of a fissile material which will achieve criticality and produce high power levels. By radiatively coupling to the surrounding fluids, extremely high temperatures in the propellant and, thus, high specific impulses can be generated. The ship velocities enabled by such performance may allow a 9 month round trip, manned Mars mission to be considered. Alternatively, one might consider slightly longer missions in ships that are heavily shielded against the intense Galactic Cosmic Ray flux to further reduce the radiation dose to the crew. The current status of the research program at the Los Alamos National Laboratory into the gas core nuclear rocket feasibility will be discussed.

Howe, S. D.↗
NASA NTRS1999

Initial Test Firing Results for Solid CO/GOX Cryogenic Hybrid Rocket Engine for Mars ISRU Propulsion Applications

ORBITEC is developing methods for producing, testing, and utilizing Mars-based ISRU fuel/oxidizer combinations to support low cost, planetary surface and flight propulsion and power systems. When humans explore Mars we will need to use in situ resources that are available, such as: energy (solar); gases or liquids for life support, ground transportation, and flight to and from other surface locations and Earth; and materials for shielding and building habitats and infrastructure. Probably the easiest use of Martian resources to reduce the cost of human exploration activities is the use of the carbon and oxygen readily available from the CO2 in the Mars atmosphere. ORBITEC has conducted preliminary R&D that will eventually allow us to reliably use these resources. ORBITEC is focusing on the innovative use of solid CO as a fuel. A new advanced cryogenic hybrid rocket propulsion system is suggested that will offer advantages over LCO/LOX propulsion, making it the best option for a Mars sample return vehicle and other flight vehicles. This technology could also greatly support logistics and base operations by providing a reliable and simple way to store solar or nuclear generated energy in the form of chemical energy that can be used for ground transportation (rovers/land vehicles) and planetary surface power generators. This paper describes the overall concept and the test results of the first ever solid carbon monoxide/oxygen rocket engine firing.

Rice, Eric E.↗
NASA NTRS1999

Catalyst Development for Hydrogen Peroxide Rocket Engines

The development of various catalysts of hydrogen peroxide was conducted for the applications of liquid rocket engines. The catalyst development includes silver screen technology, solid catalyst technology, and homogeneous catalyst technology. The silver screen technology development was performed with 85% (by weight) hydrogen peroxide. The results of this investigation were used as the basis for the catalyst design of a pressure-fed liquid-fueled upper stage engine. Both silver-plated nickel 200 screens and pure silver screens were used as the active metal catalyst during the investigation, The data indicate that a high decomposition efficiency (greater than 90%) of 85% hydrogen peroxide can be achieved at a bed loading of 0.5 lbm/sq in/sec with both pure silver and silver plated screens. Samarium oxide coating, however, was found to retard the decomposition process and the catalyst bed was flooded at lower bed loading. A throughput of 200 lbm of hydrogen peroxide (1000 second run time) was tested to evaluate the catalyst aging issue and performance degradation was observed starting at approximately 400 seconds. Catalyst beds of 3.5 inch in diameter was fabricated using the same configuration for a 1,000-lbf rocket engine. High decomposition efficiency was obtained with a low pressure drop across the bed. Solid catalyst using precious metal was also developed for the decomposition of hydrogen peroxide from 85% to 98% by weight. Preliminary results show that the catalyst has a strong reactivity even after 15 minutes of peroxide decomposition. The development effort also includes the homogeneous catalyst technology. Various non-toxic catalysts were evaluated with 98% peroxide and hydrocarbon fuels. The results of open cup drop tests indicate an ignition delay around 11 ms.

Morlan, P. W.↗
NASA NTRS1999

DC and Wave Electric Fields and Other Plasma Parameters Observed on Two Sounding Rockets in the Dark Cusp during IMF BZ North and South Conditions

Two Black Brant IX sounding rockets were launched into the dark, dayside cusp near magnetic noon on December 2 and 3, 1997, from Ny Alesund, Spitzbergen at 79degN reaching altitudes of approximately 450 km. Real-time ground-based and Wind (interplanetary magnetic field) IMF data were used to determine the launch conditions. The first launch, with Bz north conditions, crossed into and back out of an open field region with merging poleward of the projected trajectory. The second flight, into Bz south conditions, was timed to coincide with an enhancement in the merging rate from a increase in the negative Bz, while the (Defense Meteorological Satellite Program) DMSP F13 satellite was situated slightly to the north of the rocket trajectory. Each payload returned DC electric and magnetic fields, plasma waves, energetic particles, photometer data, and thermal plasma data. Data from both flights will be shown, with an emphasis on the DC electric field results. In particular, the data gathered on December 2, 1997 will be used to discuss ionospheric signatures of merging and the open/closed character of the the cusp/low latitude boundary layer. In contrast, the data gathered on December 3, 1997 shows evidence of pulsed electric field structures which will be examined in the context of cusp plasma entry processes. Both data sets returned a rich variety of plasma waves, as well as optical emissions and thermal plasma data.

Pfaff, R. F.↗