Water injection from 9 deg hemisphere-cone into a hypersonic airstream
Water injection from nozzles of RAM C spacecraft models in hypersonic wind tunnels to study ion sheath penetration characteristics of spray
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Water injection from nozzles of RAM C spacecraft models in hypersonic wind tunnels to study ion sheath penetration characteristics of spray
A high-altitude electrostatic probe experiment is described and data are presented for three RAM C reentries at velocities of approximately 25 OOO feet per second. The electron density profiles inferred from the probe measurements are compared with theoretical calculations, and the probable cause of significant disagreement is briefly discussed. Probe measurements during material-addition sequences for radio-blackout alleviation are presented, and comparisons of probe measurements with other pertinent diagnostic measurements are made.
A wind-tunnel investigation was conducted at free-stream Mach numbers from 0.20 to 1.00 and Reynolds numbers, based on maximum afterbody diameter, from 2.25 million to 6.90 million on solid models of an attached inflatable decelerator (AID) concept. Tests were conducted to obtain static and ram surface pressure distributions about the basic shapes and at various separation distances between the 120 deg conical forebody and the inflated afterbody shape. The resulting data were used to study the feasibility of extracting a payload from a conical forebody by means of an AID.
A heat-transfer design analysis has been made of an air-cooled plug-nozzle system for a supersonic-cruise aircraft engine. The proposed 10deg half-angle conical plug is sting supported from the turbine frame. Plug cooling is accomplished by convection and film cooling. The flight profile studied includes maximum afterburning from takeoff to Mach 2.7 and supersonic cruise at Mach 2.7 with a low afterburner setting. The calculations indicate that, for maximum afterburning, about 2 percent of the engine primary flow, removed after the second stage of the nine-stage compressor, will adequately cool the plug and sting support. Ram air may be used for cooling during supersonic-cruise operations, however. Therefore, the cycle efficiency penalty paid for air cooling the plug and sting support should be low.
A wind-tunnel investigation was conducted at free-stream Mach numbers from 0.20 to 1.00 and corresponding Reynolds numbers, based on maximum afterbody diameter, from 2.25 x one million to 6.90 x one million on a solid model of an attached inflatable decelerator (AID) connected to the base of an ogive-cylinder. Tests were conducted to obtain ram-air and surface pressure distributions about the AID. AID shapes derived for subsonic deployment are dependent on the pressure distributions used in their derivation, and the different shapes obtained are dependent on the Mach number for which the design is made. The resulting pressure distributions were used in a design program to obtain new shapes which were compared with the original pressure-distribution shape.
A performance development program has been conducted on a short length, double-annular, ram-induction combustor. The combustor was designed for a large augmented turbofan engine capable of sustained flight speeds up to Mach 3.0. Performance tests were conducted at an inlet temperature and Mach number simulating engine sea level takeoff conditions. At the design temperature rise of 1600 F, combustion efficiency was 100%, pattern factor was 0.20, and combined diffuser-combustor pressure loss was 4.4% or 1.12 times the diffuser inlet velocity head. A temperature rise in excess of 2400 F with a combustion efficiency of 94% was demonstrated.
The preliminary design, reference program, costs, and sortie and program options for the modular space station are outlined. The Phase B has a barbell configuration baseline with a manipulator. The baseline includes two capability plateaus, a 6-man station followed after five years by growth to a 12-man station. It is concluded that a common development approach is the most cost effective and flexible system. The system includes a module to support automated payload servicing, a set of sortie labs, and the cargo modules, RAMs, and space station modules. These would be developed and operated in conjunction with the space shuttle.
A study was conducted to develop the means to identify skills required of scientist passengers on advanced missions related to the space shuttle and RAM programs. The scope of the study was defined to include only the activities of on-orbit personnel which are directly related to, or required by, on-orbit experimentation and scientific investigations conducted on or supported by the shuttle orbiter. A program summary is presented which provides a description of the methodology developed, an overview of the activities performed during the study, and the results obtained through application of the methodology.
The vehicle related data developed during the orbital operations study are described. The interfacing activity findings have been realigned into the four basic vehicle systems as follows: (1) earth orbital shuttle (EOS), (2) research and applications module (RAM), (3) space based, ground based, manned and unmanned tugs, and (4) modular space station (MSS).
A summary of the analyses of the orbital operations study is presented. Objectives, scope of study, and technical documentation format are discussed. A summary of the mission analyses including generic mission models, element pair interactions, and interfacing activities are presented. The analyses associated with each interfacing activity are also summarized. Significant implications derived during the course of the study on the EOS orbiter, space tug, RAM, and MSS are indicated.
Evaluation of two daytime D-region positive-ion composition measurements performed at Thumba, India, for solar zenith angles of 53.2 and 27.8 deg. Comparison of upleg ram with downleg wake data shows a large increase in the concentration of heavy ions 48(+), NO(+) . H2O; 55(+), H3O(+) . (H2O)2; and M(+) greater than 65(+) for the downleg reduced shock condition. Peak concentrations of 48(+) and 55(+) occur at unit optical depth for Lyman alpha radiation. The ion 37(+), H3O(+) . H2O, is dominant for chi = 27.8 deg, but not for chi = 53.2 deg, consistent above 80 km with an origin from the X-ray production of O2(+). Laboratory measurements have shown that the ion, NO(+), can be transferred to heavy hydrates 48(+), 55(+), and M(+) greater than 65(+) by a reaction chain starting with NO(+) + X + M = NO(+) . X + M, where X can be O2, N2, CO2 or a combination of all three, depending on the rate of reaction. This chain, together with a similar reaction scheme starting with O2(+) and ending in 19(+), 37(+), and heavier clusters, is used to provide a consistent explanation for the hydrated ions observed in the D region.
Results are presented of a study conducted with a digital simulation model being used in the design of the Automatically Reconfigurable Modular Multiprocessor System (ARMMS), a candidate computer system for future manned and unmanned space missions. The model simulates the activity involved as instructions are fetched from random access memory for execution in one of the system central processing units. A series of model runs measured instruction execution time under various assumptions pertaining to the CPU's and the interface between the CPU's and RAM. Design tradeoffs are presented in the following areas: Bus widths, CPU microprogram read only memory cycle time, multiple instruction fetch, and instruction mix.
An analytical and test program was conducted in order to establish the feasibility of a multichamber pulsed-capillary viscometer. The initial design incorporated a piston, ram, and seals which produced measured pulses up to 30,000 psi in the closed chamber system. Pressure pulses from one to ten milliseconds were investigated in a system volume of 1 cuin. Four test fluids: a MIL-L-7808, a 5P4E polyphenyl ether, a MIL-L-23699A, and a synthetic hydrocarbon were examined in the test pressure assembly. The pressure-viscosity coefficient and viscosity delay time were determined for the MIL-L-7808 lubricant tested.
An evaluation of methods for emergency rescue of space crews using the Earth Orbit Shuttle was conducted. Emergency situations were analyzed for the mission categories of extravehicular activity, space shuttle orbiter, space station, and research applications module (RAM). Five different transfer concept categories were analyzed and each was scored on the basis of its operational effectiveness. A cost analysis of the transfer operations was developed.
A computer program for determining the theoretical performance of a three dimensional inlet is presented. An analysis for determining the capture area, ram force, spillage force, and surface pressure force is presented, along with the necessary computer program. A sample calculation is also included.
A viscous shock-layer analysis was developed and used to calculate nonequilibrium-flow species distributions in the plasma layer of the RAM vehicle. The theoretical electron-density results obtained are in good agreement with those measured in flight. A circular-aperture flush-mounted antenna was used to obtain a comparison between theoretical and experimental antenna admittance in the presence of ionized boundary layers of low collision frequency. The electron-temperature and electron-density distributions in the boundary layer were independently measured. The antenna admittance was measured using a four-probe microwave reflectometer and these measured values were found to be in good agreement with those predicted. Measurements were also performed with another type of circular-aperture antenna and good agreement was obtained between the calculations and the experimental results. A theoretical analysis has been completed which permits calculation of the nonequilibrium, viscous shock-layer flow field for a sphere-cone body. Results are presented for two different bodies at several different altitudes illustrating the influences of bluntness and chemical nonequilibrium on several gas dynamic parameters of interest. Plane-wave transmission coefficients were calculated for an approximate space-shuttle body using a typical trajectory.
Work is reported aimed at supporting the shuttle payload carriers, such as, the Sortie Carrier and RAM. Sketches, renderings, descriptions of scale models and full scale mock-ups, and reports required to fully explain the design recommendations are presented.
Three turbofan configurations, each incorporating alternative noise reduction features, were tested under the Quiet Engine Program. Performance data for these engines are shown over a range of flight conditions. The data are presented in tabular form for standard day flight inlet conditions. Procedures for estimating nonstandard day performance are shown. Tabular data and calculation procedures to allow determination of ram recovery, customer bleed, and customer shaft power extraction effects on engine performance can be found in the original Performance Brochure titled, Experimental Quiet Engine Program, Predicted Engine Performance, dated April 8, 1970. Predicted engine noise levels for representative take-off and approach conditions are provided.