Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nano”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Fractal coatings of Ni and NiYSZ for high-temperature corrosion mitigation in solar salt

This paper introduces a novel approach to corrosion mitigation using electrodeposited, fractal Ni and NiYSZ coatings. Highly adherent, durable multiscale coatings with fractal dimensions above 1.80 were fabricated. Corrosion characteristics of coated plain and etched surfaces of In800H, SS310, SS316 and SS347, in comparison to Ha230, were studied in molten 60% NaNO 3 + 40% KNO 3 at 600 °C. The corrosion rate of coated Fe-based alloys reduced by up to 68% compared to uncoated alloys and was on par with or lower than the corrosion rate of Ha230. Furthermore, the corrosion-resistant coatings provide for use of low-cost alloys in high temperature corrosive environments.

36 MATERIALS SCIENCE↗

Influence of carbon nanotubes on microstructure and corrosion performance of additively manufactured 316L stainless steel

For this study, laser powder bed fusion (LPBF) was performed on feedstock-modified 316L stainless steel powder with 1 and 2 vol% carbon nanotubes (CNT). The corrosion resistance was evaluated following cyclic potentiodynamic polarization tests conducted in 0.6 M NaCl at room temperature, 35 and 50 °C, and immersion tests in 6 % FeCl 3 . The CNT addition has increased the pitting potential and decreased number of pits formed during immersion in FeCl 3 solution, which could be attributed to Mn-Si-O nano inclusions refinement and segregation of chromium around the inclusions. The observed corrosion behavior was correlated with the altered microstructure due to CNT addition.

36 MATERIALS SCIENCE↗

TTDFT: A GPU accelerated Tucker tensor DFT code for large-scale Kohn-Sham DFT calculations

We present the Tucker tensor DFT (TTDFT) code which uses a tensor-structured algorithm with graphic processing unit (GPU) acceleration for conducting ground-state DFT calculations on large-scale systems. The Tucker tensor DFT algorithm uses a localized Tucker tensor basis computed from an additive separable approximation to the Kohn-Sham Hamiltonian. The discrete Kohn-Sham problem is solved using Chebyshev filtered subspace iteration method that relies on matrix-matrix multiplications of a sparse symmetric Hamiltonian matrix and a dense wavefunction matrix, expressed in the localized Tucker tensor basis. These matrix-matrix multiplication operations, which constitute the most computationally intensive step of the solution procedure, are GPU accelerated providing ~8-fold GPU-CPU speedup for these operations on the largest systems studied. In conclusion, the computational performance of the TTDFT code is presented using benchmark studies on aluminum nano-particles and silicon quantum dots with system sizes ranging up to ~7,000 atoms.

97 MATHEMATICS AND COMPUTING↗

Towards high data-rate diffusive molecular communications: A review on performance enhancement strategies

Diffusive molecular communications (DiMC) have recently gained attention as a candidate for nano- to micro- and macro-scale communications due to its simplicity and energy efficiency. As signal propagation is solely enabled by Brownian motion mechanics, DiMC faces severe inter-symbol interference (ISI), which limits reliable and high data-rate communications. Herein, recent literature on DiMC performance enhancement strategies is surveyed; key research directions are identified. Signaling design and associated design constraints are presented. Here, studies on fundamental information theoretic limits of DiMC channel are reviewed. Classical and novel transceiver designs are discussed with an emphasis on methods for ISI mitigation and performance-complexity tradeoffs. Key parameter estimation strategies such as synchronization and channel estimation are considered in conjunction with asynchronous and timing error robust receiver methods. Finally, source and channel coding in the context of DiMC is presented.

42 ENGINEERING↗

Electrochemical noise studies on localized corrosion of Ni and Ni-20Cr in molten ZnCl 2

The electrochemical noise (ECN) technique was employed to study corrosion of two model systems, i.e. pure Ni and a binary Ni-20 wt%Cr (Ni20Cr) alloy in molten ZnCl 2 at 623 K. Here we measured ECN transients in current and open-circuit potential from two nominally identical Ni-Ni and Ni20Cr-Ni20Cr electrodes and one galvanic Ni-Ni20Cr electrode pair. The behavior of ECN is quite distinct among the three-electrode systems, and it is correlated with the various microscopic observations of micro- and nano-scale morphological features. Based on the ECN study coupled with the microstructural analysis, the origins of ECN in the molten salt environment as well as the mechanisms of localized corrosion in the three systems are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Stochastic generation of electrolyzer anode catalyst layers

Here, we introduce a stochastic methodology to reproduce the complex pore structure observed in commercial iridium catalyst layers. This method preserves the α pore (pores smaller than 250 nm) and β pore (pores greater than or equal to 250 nm) regions of the catalyst layer. The morphology of the generated materials was validated by comparing the pore size distributions of generated materials against those obtained from commercial materials imaged using x-ray nano computed tomography. We further demonstrate that the pore size distributions of the generated materials are statistically indistinguishable from the imaged catalyst layers, indicating that the stochastic methodology is capable of accurately reproducing catalyst layer morphology. Pore network modelling was conducted on the generated catalyst materials to simulate single-phase permeability, electrical conductivity, and ionic conductivity, and these properties were found to be within experimentally measured ranges for electrolyzer catalyst layers. Additionally, simulations were performed on the generated materials with varying ionomer and iridium catalyst loadings. As the ionomer loading is added, proton conductivity increases exponentially, which demonstrates the importance of optimizing ionomer loading, considering that these effects will be exacerbated in the hydration and temperature conditions of operating electrolyzers. The stochastic material generation method presented in this work is a powerful tool for the development of novel low loading catalyst layers, where the effect of various structural parameters on electrolyzer performance characteristics can be explored.

36 MATERIALS SCIENCE↗

C@SnS 2 core-shell 0D/2D nanocomposite with excellent electrochemical performance as lithium-ion battery anode

C@SnS 2 core-shell 0D/2D nanocomposite was successfully prepared by a one-step hydrothermal method. The SnS 2 nanosheets were heterogeneously nucleated and grown on the surface of carbon spheres. As an anode for lithium-ion batteries, the electrochemical performance of the C@SnS 2 composite outperforms that of SnS 2 nanoflowers. After 100 cycles, the reversible discharge specific capacity reaches an impressive value of 802 mAh g -1 at a current density of 100 mA g -1 . Even after 600 cycles, the discharge specific capacity remains a value of 442 mAh g -1 , under a high current density of 1 A g -1 . Further, this remarkable lithium-ion storage performance can be attributed to the unique core-shell nanostructure and the synergy between SnS 2 nanosheets and carbon spheres. This study advances our understanding of the vital role of carbon in fabricating nano-heterojunction or composite electrodes and provides a feasible route to significantly improve the electrochemical properties of SnS 2 and other metal sulfides.

25 ENERGY STORAGE↗

Nanomechanical investigation of the interplay between pore morphology and crack orientation of amorphous silica

Porous amorphous silica (a-SiO 2 ) is of both fundamental and practical interests, as they exhibit a large specific surface area and tunable porous network. However, the brittle nature of a-SiO 2 and the presence of pre-existing cracks at both micro- and nano-scales lead to complex mechanical behavior. Here, we systematically investigate the effects of pre-existing crack and its orientation on the mechanical properties of a-SiO 2 with varying pore shapes using reactive molecular dynamics simulations. We demonstrate that pore shape will primarily influence the Young’s modulus (E) and critical energy release rate (G IC ). We further investigate the impact of pore shape and crack orientation by local characterization of the structural parameters. By defining the high stress and inter-mediate regions, the overall mechanical properties are found to be greatly influenced by the pore shape which can be reflected through the spatial distribution of von Mises stress. Overall, G IC is found to increase with the increase of ligament length (also known as pore wall thickness). Meanwhile, the effect of the pre-existing crack on the crack propagation process is confirmed by analyzing the density distribution evolution. These results highlight the interplay between pore morphology and crack orientation in controlling the fracture behaviors in brittle porous materials.

42 ENGINEERING↗

Multi-scale stabilization of high-voltage LiCoO 2 enabled by nanoscale solid electrolyte coating

LiCoO 2 (LCO) possess a high theoretical specific capacity of 274 mAh g -1 , and currently LCO charged to 4.48 V with a capacity of ~190–195 mAh g -1 is penetrating the commercial markets. Scalable strategies to further enhance the performance of LCO are highly attractive. Here, we develop a scalable ball-milling and sintering method to tackle this long-standing challenge by modifying LCO surface with only 1.5–3.5% ceramic solid electrolyte nanoparticles, specifically Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) as an example. Consequently, the atomic-to-meso multiscale structural stabilities have been significantly improved, even with a high cut-off voltage of 4.5 V vs. Li/Li + , leading to excellent electrochemical stabilities. The nano-LAGP modified Li|LCO cell exhibits high discharge capacity of 196 mAh g -1 at 0.1 C, capacity retention of 88% over 400 cycles, and remarkably enhanced rate capability (163 mAh g -1 at 6 C). These results show significant improvement compared to the Li|LCO cells. The as-prepared graphite|LAGP-LCO full cells also show steady cycling with 80.4% capacity retention after 200 cycles with a voltage cut-off of 4.45 V. This work provides a simple and scalable approach to achieve stable cycling of LCO at high voltage with high energy density.

25 ENERGY STORAGE↗

An ultrathin solid-state electrolyte film coated on LiNi 0.8 Co 0.1 Mn 0.1 O 2 electrode surface for enhanced performance of lithium-ion batteries

We report layered Ni-rich oxide is a promising cathode material for lithium-ion batteries (LIBs) of high energy density, yet its poor electrochemical stability induced by electrode-electrolyte interfacial degradation has still needed to be addressed. Surface coating is one of the powerful techniques to tackle this issue, nevertheless, it has been extensively used on particle but not electrode regarding a larger area of protection. Herein, we have covered a nano-scaled layer of lithium phosphorus oxynitride (LiPON) on the electrode level of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM) surface and found lower impedance, longer cycle life, and better safety for treated battery. Most notably, such an NCM-LiPON based 1.3 Ah pouch cell delivers an energy density of 364.4 Wh kg -1 (based on positive and negative materials), along with the retention of 80.0% over 745 cycles at 0.5 C-rate, which is 1.3 times longer than the bare one. This results from modification of both superficial cathode-electrolyte interphase (CEI) and structure stabilization of general particle surface, therefore, role of conformal coating upon electrode surface should be highlighted.

36 MATERIALS SCIENCE↗

Long cycle and calendar life of Si-based Li-ion batteries enabled by localized high-concentration electrolytes and their surprising water tolerance

Silicon-based anodes promise an increase in energy density for Li-ion batteries, yet they suffer from a poor calendar life. Researchers have posited that fluorinated lithium salt forms reactive side products that destroy the solid electrolyte interphase (SEI), even without cycling. HF is one such reactive side product formed from trace water contamination in the electrolyte. Some electrolytes, such as localized high concentration electrolytes (LHCEs) may improve cell stability in highly reactive systems, such as Li metal and Si. In the present study, LHCEs containing 200-300 ppm of water retained up to 8% greater capacity (1200-1300 mAh/g Si) in calendar life tests over 200 days compared to dried electrolytes (< 20 ppm water). Calendar aging took place at 100% state of charge. Cells with 200-300 ppm water performed comparably to cells with 20 ppm water in cycle life tests (900-1000 mAh/g Si) . Even adding 1000 ppm water did not lead to rapid capacity fade in cells undergoing cycle life tests. Nano-FTIR spectroscopy revealed chemical and structural differences in the SEI for cells with 1000 ppm water compared to 200-300 ppm water. The SEI differences, including increased Li2O concentration, may have contributed to improved calendar life. This research reveals the capabilities of LHCEs to improve the calendar and cycle life of Si-based Li-ion batteries, despite the presence of a highly reactive contaminant.

25 ENERGY STORAGE↗

Structural evolution during gelation of pea and whey proteins envisaged by time-resolved ultra-small-angle x-ray scattering (USAXS)

Hydrogels from plant proteins commonly exhibit inferior gel strength compared to those from dairy proteins partially due to their distinct gel networks. How protein aggregates to form such networks in response to heat remains largely unknown. In this work, pea (PPI) and whey (WPI) protein isolate gels were produced at the same protein content and similar heating/cooling rate. The process was monitored using rheology, microscopy and in situ ultra-small-angle x-ray scattering (USAXS). Rheology showed an initial decrease in G' and G'' in PPI followed by a steady increase when the temperature surpassed ~60 °C whereas a much higher temperature (~80 °C) was required for WPI, both using 2 °C/min heating rate. Microscopy showed a coarse and heterogenous network in PPI, whereas for WPI, the network was finer and more continuous. In both gels, nano-sized spherical or ellipsoidal particles were present as the basic constituents. USAXS found individual protein was dominant in PPI or WPI solution at temperature below 57 °C. Their proportions decreased together with appearance of aggregates with an average R g of 9–10 nm in PPI and 6–7 nm in WPI at higher temperature. The size of the aggregates changed slightly during further heating and cooling, but their proportions increased. Power law exponents revealed the aggregates were mass fractals for WPI and PPI gels, and they became more compact during heating. Our findings suggested formation of primary aggregates in protein gel networks is a more organized process and provided theoretical guidance for production of high protein food gels with desirable texture.

59 BASIC BIOLOGICAL SCIENCES↗

Dynamic in situ imaging of methane hydrate formation in coal media

Fast 3D X-ray imaging has proved to provide crucial insights into multi-phase dynamic processes in various geomaterials. In particular, many in situ imaging experiments have been made to study gas-hydrate formation in porous sandy samples. Such imaging is challenging for the methane gas-hydrate formation in coal samples because of the coal micro-porosity structure and lower X-ray contrast. Here we present results of the first dynamic in situ micro-computed tomography experiment of methane-hydrate formation in coal samples. Synchrotron phase-contrast tomography techniques allowed to achieve necessary contrast levels to separate all the materials of interest (gas, water, coal, and gas hydrate) in reconstructed images with high spatial and temporal resolution. The imaging results are compared to the ones from a similar tomographic experiment with sand samples. Methane-hydrate formation is accompanied by the water movements caused by cryogenic water suction that happens in sequences of short fast movements with longer equilibrium states in between. Only one type of the hydrate formation was observed in coal (growth as shells on grain boundaries) as opposed to three types in sand (shells, growth into gas pockets, and inside water volumes). In particular, this leads to a slower hydrateformation speed in coal. For the coal sample, we also observed water extraction from grains, and interpreted it as competitive sorption of methane. Lastly, we visualized the dynamic behavior of this water extraction via microchannels inside the coal grains, and performed nano-tomography imaging of these channels for a better understanding of this phenomenon.

58 GEOSCIENCES↗

Integrated experimental studies of pore structure and fluid uptake in the Bossier Shale in eastern Texas, USA

Within the Haynesville-Bossier Shale complex, the Bossier Shale has not been extensively studied by either industry and academia, despite it being an unconventional gas reservoir and a potential caprock for carbon storage in the underlaying Haynesville Shale. The lack of knowledge of the complex pore structures and fluid-rock interactions hinders the effective extraction of gas and the characterization of fluid reservoirs and sealing capacity. Integrated experimental studies of pore structure and fluid-rock interactions were conducted in seven Bossier Shale core samples collected in eastern Texas. Petrographic, geochemical, and petrophysical properties such as mineral composition, organic richness, thermal maturity, porosity, pore/pore throat diameter distribution, water-accessible pores, liquid water imbibition, and water vapor adsorption were characterized using complementary approaches of thin-section petrography, scanning electron microscopy, X-ray diffraction, total organic matter, pyrolysis, mercury intrusion porosimetry, nuclear magnetic resonance, (Ultra-) small angle X-rays scattering as well as small angle neutron scattering with deuterated liquids and contrast variation. Further, the results show that the thermally mature Bossier Shales are composed of mixed argillaceous mudstone, mixed mudstone, and mixed carbonate mudstone. The shale contains both organic and inorganic pores, with porosities of 3.24-9.37 %, pore-to-throat ratios of 1.65 to 19.4, and water-accessible pores accounting for 28.7-72.6 % of total pores. Approaches of liquid water imbibition and water vapor adsorption, with and without direct contact of water with shale samples, indicate that liquid water first enters the nano-sized pores under high capillary pressures, and water vapor adsorption is mainly controlled by both clay minerals and pores with diameters less than 10 nm. These findings contribute to a better understanding of pore structures and water-shale interactions and their controlling factors in the Bossier Shale.

58 GEOSCIENCES↗

Search for meteoritic GEMS II: Comparison of inclusions in amorphous silicates from the Paris chondrite and from anhydrous chondritic interplanetary dust particles

Amorphous silicates containing abundant nano-inclusions have been reported in the Paris CM chondrite (Leroux et al., 2015). They have chemical and morphological similarities to glass with embedded metal and sulfides (GEMS) found in interplanetary dust particles (IDPs) and micrometeorites believed to originate from comets. We used scanning transmission electron microscopy (STEM) with energy-dispersive X-ray spectroscopy (EDS) and nanodiffraction to study the chemistry and mineralogy of these inclusions in order to understand the origin of the GEMS-like material in Paris and its possible relationships to other materials found in primitive chondritic materials including IDP GEMS. EDS and diffraction analyses indicate compositional and mineralogical differences between the nanophase inclusions in cometary GEMS and Paris GEMS-like material. Metal inclusions are notably absent within Paris amorphous silicate. Ni-rich sulfides, including pentlandite, are common in even the least altered matrix material of Paris, while they are absent in GEMS-bearing IDPs and Ultracarbonaceous Antarctic Micrometeorites (UCAMMs). From examination of the inclusions, we cannot yet confirm or refute the possibility that GEMS-like material in Paris is related to cometary GEMS. The distinct compositions and mineralogy of the Paris material may be due to aqueous alteration of cometary GEMS precursors, but they may also denote an independent origin for meteoritic GEMS-like assemblages.

58 GEOSCIENCES↗

Effects of particle size and AQDS on the flow of electron equivalents between magnetite and aqueous Fe2+

Magnetite can occur naturally in nano- to micro-size regimes and widely coexists with aqueous Fe2+ (Fe2+ (aq)) in natural environments. However, the effects of magnetite particle size on its interaction with Fe2+ (aq) in anoxic subsurface environments, particularly with redox-active organics, remain unclear. In this study, the interactions of Fe2+ (aq) with magnetite particles of 12 nm versus 109 nm (Mag-12 vs. Mag-109), with/without anthraquinone- 2,6-disulfonate (AQDS), were studied based on equilibrium Fe2+ (aq) concentrations, kinetics of AQDS reduction, and structural versus surface-localized Fe(II)/Fe(III) ratios (xstru and xsurf) of magnetite. In the absence of AQDS, Mag-12 tends to release Fe2+ (aq) at pH 7 but sorb Fe2+ (aq) at pH 8, while Fe2+ (aq) uptake by Mag-109 is observed at both pH 7 and 8. The amounts of Fe2+ (aq) adsorbed per unit area of Mag-109 is higher than that of Mag-12, due to the higher electron-accepting capacity of Mag-109 that facilitates interfacial electron transfer (IET) from surfaceassociated Fe(II) to structural Fe(III). The increases of xstru and xsurf in Mag-109 after reaction with Fe2+ (aq) at pH 7 and 8 suggest Fe2+ (aq) incorporation or electron injection into the structure of Mag-109. The presence of AQDS promotes Fe2+ (aq) uptake by both Mag-12 and Mag-109. However, AQDS reduction by Fe2+-amended Mag-12 results in the decrease of xstru and inhibits Fe2+ (aq) incorporation or electron injection into the structure. On the contrary, the increase of xstru observed in Fe2+-amended Mag-109 after reaction with AQDS suggests that Fe2+ (aq) incorporation or electron injection into the surface structure and then consequently into the interiors is more favorable for magnetite with larger particle sizes. The different flow directions of electron equivalents across the solid-solution interfaces can be attributed to the relatively higher electron-accepting capacity, i.e. redox potential, of Mag-109 than Mag-12; larger particle sizes facilitate IET from surface-associated Fe(II) to structural Fe(III) and promotes further Fe2+ (aq) uptake, culminating in the pronounced changes of redox potentials in magnetitebearing solutions. The results demonstrate that particle size and redox-active organics are important factors to affect reductive activity of Fe2+-magnetite system in redox-oscillating environments.

Peng, Huan↗

Molecular dynamics simulations of energy accommodation between gases and polymers for ultra-low thermal conductivity insulation

Determining the energy accommodation between gases and solids is essential to developing porous thermal insulation materials with ultra-low effective thermal conductivity that reduce energy use, greenhouse gas emissions, and fossil fuel consumption. The energy accommodation coefficients of most gases, however, have been rarely studied, especially with respect to solids that have relatively high thermal resistivity, e.g., polymers. Here, by using all-atom nonequilibrium molecular dynamics simulations, we reveal the accommodation coefficients of He, Ar, N 2 , and O 2 with polymers, mainly polystyrene. We find that their values are around 0.51, 0.72, 0.79, and 0.90, respectively, suggesting a critical reexamination of the commonly used theoretical maximum value of 1. We have also conducted experiments and validated the value for air, which is about 0.81. Such a change in accommodation coefficients can lead to a reduction of about 70%, 50%, 35%, and 20% in the thermal conductivity of He, Ar, N 2 , and O 2 gases in nano pores (below 100 nm) or at low pressures (below 1 millibar). With these new accommodation coefficients, we find that in a 10 nm pore with ambient pressure at 300 K, the gas thermal conductivity of He, Ar, N 2 , and O 2 in porous polystyrene can be as low as 9.7 × 10 –4 , 3.4 × 10 –4 , 7.3 × 10 –4 , and 8.5 × 10 –4 W·m –1 ·K –1 , respectively, which are two to three orders of magnitude lower than their bulk values, promising higher thermal resistivity of insulation materials. This work reveals the fundamental energy exchange between gases and polymers, providing important guidance for designing high-performance thermal insulation materials for various applications.

36 MATERIALS SCIENCE↗

Coupled continuum and network model framework to study catalyst layers of polymer electrolyte fuel cells

The nanostructured thin film (NSTF) catalyst layers which have demonstrated high power densities, mass activities, and exceptional metal and support stability can have limited operational robustness due to their thin thickness and the hydrophilicity of the metal-coated nano whiskers. The dispersed nanostructured thin film (dNSTF) catalyst layers have been developed by dispersing the NSTF Pt whiskers with ionomer and carbon support to increase the thickness and hydrophobicity. Continuum and network models (NM) are coupled through boundary conditions to study the polymer electrolyte fuel cell with a dNSTF cathode catalyst layer. The coupled model combines the computational efficiency of the continuum model with the pore-scale information in the dNSTF cathode catalyst layer of the NM. It captures the special morphology of the partially ionomer/water covered cylindrical whiskers, as well as water percolation through the pore structures and their impact on the cell performance. Here we observe optimal ionomer coverage on whiskers to be 0.5, ionomer to carbon ratio to be 0.9 and higher whisker to carbon ratios to be desired.

08 HYDROGEN↗