Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Spin current generation from sputtered Y₃Fe₅O₁₂ films

Spin current injection from sputtered yttrium iron garnet (YIG) films into an adjacent platinum layer has been investigated by means of the spin pumping and the spin Seebeck effects. Films with a thickness of 83 and 96 nanometers were fabricated by on-axis magnetron rf sputtering at room temperature and subsequent post-annealing. From the frequency dependence of the ferromagnetic resonance linewidth, the damping constant has been estimated to be (7.0 ± 1.0) × 10⁻⁴. Magnitudes of the spin current generated by the spin pumping and the spin Seebeck effect are of the same order as values for YIG films prepared by liquid phase epitaxy. The efficient spin current injection can be ascribed to a good YIG|Pt interface, which is confirmed by the large spin-mixing conductance (2.0 ± 0.2) × 10¹⁸m⁻².

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Physical properties of Al{sub x}In{sub 1–x}N thin film alloys sputtered at low temperature

In this paper, we report on the structural, optical, and electrical properties of a wide compositional range of Al{sub x}In{sub 1–x}N thin layers deposited on glass and polyethylene terephthalate substrates. Al{sub x}In{sub 1–x}N layers of controlled composition were obtained by a simple reactive magnetron co-sputtering protocol, using a single aluminium target with indium insets, by varying the Al/In target surface area ratio, and the composition of the deposition atmosphere. The relevant physical properties were investigated and discussed. It is shown that the texture of the thin films is dependent on the cation ratio, while the bowing parameters of lattice constants and band gap values are larger than those of epitaxial layers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Cyclic voltammetry on sputter-deposited films of electrochromic Ni oxide: Power-law decay of the charge density exchange

Ni-oxide-based thin films were produced by reactive direct-current magnetron sputtering and were characterized by X-ray diffraction and Rutherford backscattering spectroscopy. Intercalation of Li{sup +} ions was accomplished by cyclic voltammetry (CV) in an electrolyte of LiClO{sub 4} in propylene carbonate, and electrochromism was documented by spectrophotometry. The charge density exchange, and hence the optical modulation span, decayed gradually upon repeated cycling. This phenomenon was accurately described by an empirical power law, which was valid for at least 10{sup 4} cycles when the applied voltage was limited to 4.1 V vs Li/Li{sup +}. Our results allow lifetime assessments for one of the essential components in an electrochromic device such as a “smart window” for energy-efficient buildings.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Low dark current and high speed ZnO metal–semiconductor–metal photodetector on SiO{sub 2}/Si substrate

ZnO thin films are deposited by radio-frequency magnetron sputtering on thermally grown SiO{sub 2} on Si substrates. Pt/Au contacts are fabricated by standard photolithography and lift-off in order to form a metal-semiconductor-metal (MSM) photodetector. The dark current of the photodetector is measured as 1 pA at 100 V bias, corresponding to 100 pA/cm{sup 2} current density. Spectral photoresponse measurement showed the usual spectral behavior and 0.35 A/W responsivity at a 100 V bias. The rise and fall times for the photocurrent are measured as 22 ps and 8 ns, respectively, which are the lowest values to date. Scanning electron microscope image shows high aspect ratio and dense grains indicating high surface area. Low dark current density and high speed response are attributed to high number of recombination centers due to film morphology, deducing from photoluminescence measurements. These results show that as deposited ZnO thin film MSM photodetectors can be used for the applications needed for low light level detection and fast operation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High upper critical field in disordered niobium nitride superconductor

Superconducting Niobium Nitride thin films have been deposited on glass, aluminum nitride buffered glass, and oxidized silicon substrates by reactive DC magnetron sputtering at ambient substrate temperatures. The crystal structure of these thin films has been determined to be cubic fcc B1 structure by Glancing Incidence X-Ray Diffraction analysis. The superconducting transition temperatures of the thin films were measured to be greater than 11.6 K with a maximum of 13.4 K. The negative temperature coefficient of resistance observed in these thin films indicates the presence of disorder. Magneto-resistance measurements have been carried out on these thin films patterned into standard four probe geometry upto a maximum magnetic field of 12 T for two films and upto 15 T for the other two films. The dependence of transition temperature on the applied field is analyzed to estimate the upper critical field. The upper critical field for most of the films was estimated to exceed 35 T, while one of the most disordered films had an estimated upper critical field greater than 70 T.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Room temperature ferromagnetic and ferroelectric properties of Bi{sub 1−x}Ca{sub x}MnO{sub 3} thin films

Bi{sub 1−x}Ca{sub x}MnO{sub 3} (BCMO) thin films with x = 0, 0.1, 0.2, 0.3 and 0.4 are successfully deposited on the n-type Si (100) substrate at two different temperatures of 400 °C and 800 °C using RF magnetron sputtering. The stoichiometry of the films and oxidation state of the elements have been described by X-ray photoelectron spectroscopy analysis. Dielectric measurement depicts the insulating property of BCMO films. Magnetic and ferroelectric studies confirm the significant enhancement in spin orientation as well as electric polarization at room temperature due to incorporation of Ca{sup 2+} ions into BiMnO{sub 3} films. The BCMO (x = 0.2) film grown at 400 °C shows better magnetization (M{sub sat}) and polarization (P{sub s})with the measured values of 869 emu / cc and 6.6 μ{sub C}/ cm{sup 2} respectively than the values of the other prepared films. Thus the realization of room temperature ferromagnetic and ferroelectric ordering in Ca{sup 2+} ions substituted BMO films makes potentially interesting for spintronic device applications.

36 MATERIALS SCIENCE↗

Characterization of energetic and thermalized sputtered atoms in pulsed plasma using time-resolved tunable diode-laser induced fluorescence

In this work, a time-resolved tunable diode-laser (DL) induced fluorescence (TR-TDLIF) method calibrated by absorption spectroscopy has been developed in order to determine atom and flux velocity distribution functions (AVDF and FVDF) of the energetic and the thermalized atoms in pulsed plasmas. The experimental set-up includes a low-frequency (∼3 Hz) and high spectral-resolution DL (∼0.005 pm), a fast rise-time pulse generator, and a high power impulse magnetron sputtering (HiPIMS) system. The induced TR-TDLIF signal is recorded every 0.5 μs with a digital oscilloscope of a second-long trace. The technique is illustrated with determining the AVDF and the FVDF of a metastable state of the sputtered neutral tungsten atoms in the HiPIMS post-discharge. Gaussian functions describing the population of the four W isotopes were used to fit the measured TR-TDLIF signal. These distribution functions provide insight into transition from the energetic to thermalized regimes from the discharge onset. This technique may be extended with appropriate DLs to probe any species with rapidly changing AVDF and FVDF in pulsed and strongly oscillating plasmas.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Reconstruction mechanisms of tantalum oxide coatings with low concentrations of silver for high temperature tribological applications

Silver tantalate (AgTaO{sub 3}) coatings have been found to exhibit outstanding tribological properties at elevated temperatures. To understand the mechanisms involved in the tribological behavior of the Ag-Ta-O system, tantalum oxide coatings with a small content of silver were produced to investigate the metastable nature of this self-lubricating material. The coatings were produced by unbalanced magnetron sputtering, ball-on-disk wear tested at 750 °C, and subsequently characterized by X-ray diffraction, Scanning Auger Nanoprobe, cross-sectional Scanning Electron Microscopy, and Transmission Electron Microscopy. Complementary molecular dynamic simulations were carried out to investigate changes in the chemical and structural properties at the interface due to sliding for films with varying silver content. Both the experimental characterization and the theoretical modeling showed that silver content affects friction and wear, through the role of silver in film reconstruction during sliding. The results suggest that the relative amount of silver may be used to tune film performance for a given application.

36 MATERIALS SCIENCE↗

Microwave heating device for internal heating convection experiments, applied to Earth's mantle dynamics

We report the design, construction, and performances of a microwave (MW) heating device for laboratory experiments with non-contact, homogeneous internal heating. The device generates MW radiation at 2.47 GHz from a commercial magnetron supplied by a pulsed current inverter using proprietary, feedback based command and control hardware and software. Specially designed MW launchers direct the MW radiation into the sample through a MW homogenizer, devised to even the MW power distribution into the sample's volume. An adjustable MW circuit adapts the MW generator to the load (i.e., the sample) placed in the experiment chamber. Dedicated heatsinks maintain the MW circuits at constant temperature throughout the experiment. Openings for laser scanning for image acquisition with a CCD camera and for the cooling circuits are protected by special MW filters. The performances of the device are analyzed in terms of heating uniformity, long term output power stability, and load matching. The device is used for small scale experiments simulating Earth's mantle convection. The 30 × 30 × 5 cm{sup 3} convection tank is filled with a water‑based viscous fluid. A uniform and constant temperature is maintained at the upper boundary by an aluminum heat exchanger and adiabatic conditions apply at the tank base. We characterize the geometry of the convective regime as well as its bulk thermal evolution by measuring the velocity field by Particle Image Velocimetry and the temperature field by using Thermochromic Liquid Crystals.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Substrate-dependent thermal conductivity of aluminum nitride thin-films processed at low temperature

In this paper, we report on investigation concerning the substrate-dependent thermal conductivity (k) of Aluminum Nitride (AlN) thin-films processed at low temperature by reactive magnetron sputtering. The thermal conductivity of AlN films grown at low temperature (<200 °C) on single-crystal silicon (Si) and amorphous silicon nitride (SiN) with thicknesses ranging from 100 nm to 4000 nm was measured with the transient hot-strip technique. The k values for AlN films on SiN were found significantly lower than those on Silicon consistently with their microstructures revealed by X-ray diffraction, high resolution scanning electron microscopy, and transmission electron microscopy. The change in k was due to the thermal boundary resistance found to be equal to 10 × 10{sup −9} Km{sup 2}W{sup −1} on SiN against 3.5 × 10{sup −9} Km{sup 2}W{sup −1} on Si. However, the intrinsic thermal conductivity was determined with a value as high as 200 Wm{sup −1}K{sup −1} whatever the substrate.

36 MATERIALS SCIENCE↗

Electronic state of Er in sputtered AlN:Er films determined by magnetic measurements

The optoelectronic and piezoelectric properties of AlN:Er thin films have been of great recent interest for potential device applications. In this work, the focus is on the electronic state of Er in AlN:Er thin films prepared by reactive magnetron sputtering on (001) p-type Si substrate. X-ray diffraction shows that Er doping expands the lattice and the AlN:Er film has preferential c-plane orientation. To determine whether Er in AlN:Er is present as Er metal, Er{sub 2}O{sub 3}, or Er{sup 3+} substituting for Al{sup 3+}, detailed measurements and analysis of the temperature dependence (2 K–300 K) of the magnetization M at a fixed magnetic field H along with the M vs. H data at 2 K up to H = 90 kOe are presented. The presence of Er{sub 2}O{sub 3} and Er metal is ruled out since their characteristic magnetic transitions are not observed in the AlN:Er sample. Instead, the observed M vs. T and M vs. H variations are consistent with Er present as Er{sup 3+} substituting for Al{sup 3+} in AlN:Er at a concentration x = 1.08% in agreement with x = 0.94% ± 0.20% determined using x-ray photoelectron spectroscopy (XPS). The larger size of Er{sup 3+} vs. Al{sup 3+}explains the observed lattice expansion of AlN:Er.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Structural, magnetic, and transport properties of sputtered hexagonal MnNiGa thin films

We report on a systematical study of the structure, magnetism, and magnetotransport behavior of the hexagonal MnNiGa films deposited on thermally oxidized Si (001) substrates by magnetron sputtering. X-ray diffractions reveal that all the films deposited at different temperatures crystallized in hexagonal Ni{sub 2}In-type structure (space group P6{sub 3}/mmc). Scanning electron microscopy observations show that the surface morphology of the films varies with deposition temperature, and energy dispersive spectroscopy analysis shows compositions of the films remain nearly unchanged, independent of the deposition temperature. Magnetic measurements indicate that all films are ferromagnetic and exhibit a magnetic anisotropy behavior. The magnetoresistance (MR) exhibits a negative temperature- and field-dependent behavior. The possible origin of the negative MR is discussed. Furthermore, we found that the Hall effect is dominated by an anomalous Hall effect (AHE) only due to skew scattering independent of the deposition temperature of films. Moreover, the anomalous Hall resistivity presents a non-monotonously temperature-dependent behavior.

36 MATERIALS SCIENCE↗

Effect of temperature on the current (capacitance and conductance)–voltage characteristics of Ti/n-GaAs diode

In this study, Ti/n-GaAs Schottky barrier diode has been fabricated by DC magnetron sputtering. The current–voltage, capacitance–voltage, and conductance–voltage characteristics of Ti/n–GaAs diode have been investigated in the temperature range of 80–320 K. The ideality factor and barrier height values have been calculated from the forward current–voltage characteristics. The variation of the diode parameters with the sample temperature has been attributed to the presence of the lateral inhomogeneities of the barrier height. The temperature dependent capacitance–voltage characteristics have been measured to calculate the carrier concentration, diffusion potential, barrier height, and temperature coefficient of the barrier height (α = −0.65 meV K{sup −1}). The fact that the temperature coefficient of the barrier height changes from metal to metal has been ascribed to the chemical nature of the contact metal or metal electronegativity.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The effects of tungsten concentration on crystalline structure and perpendicular magnetic anisotropy of Co-W films

In this study, Co-W thin films deposited by DC magnetron sputtering were demonstrated to be perpendicular magnetic anisotropic with large magnetocrystalline anisotropy energy (MAE). Thermodynamic calculations based on Miedema’s semi-empirical model have been used to estimate the phase in this binary alloy system. Based on the thermodynamic calculations results, a series of Co-W thin films were deposited on amorphous Ta underlayer with different tungsten concentrations. According to the X-ray diffraction results, the crystal structure of Co-W thin films is consistent well with that of thermodynamic calculations. Large MAE of Co-W thin films can be obtained with K{sub u} over 2.1 × 10{sup 5} J/m{sup 3} after vacuum annealing. The perpendicular coercivity (H{sub c}) of Co-W thin film reaches 9.1 × 10{sup 4} A/m. Therefore, the Co-W thin film is considered as a potential choice of high-density magnetic recording media materials.

36 MATERIALS SCIENCE↗

Study of breakdown voltage of indium-gallium-zinc-oxide-based Schottky diode

In contrast to the intensive studies on thin-film transistors based on indium gallium zinc oxide (IGZO), the research on IGZO-based diodes is still very limited, particularly on their behavior and stability under high bias voltages. Our experiments reveal a sensitive dependence of the breakdown voltage of IGZO Schottky diodes on the anode metal and the IGZO film thickness. Devices with an Au anode are found to breakdown easily at a reverse bias as low as −2.5 V, while the devices with a Pd anode and a 200-nm, fully depleted IGZO layer have survived up to −15 V. All diodes are fabricated by radio-frequency magnetron sputtering at room temperature without any thermal treatment, yet showing an ideality factor as low as 1.14, showing the possibility of achieving high-performance Schottky diodes on flexible plastic substrate.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Thermoelectric properties of DC-sputtered filled skutterudite thin film

The Yb filled CoSb{sub 3} skutterudite thermoelectric thin films were prepared by DC magnetron sputtering. The electrical conductivity, Seebeck coefficient, thermal conductivity, and figure of merit ZT of the samples are characterized in a temperature range of 300 K to 700 K. X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy are obtained to assess the phase composition and crystallinity of thin film samples at different heat treatment temperatures. Carrier concentrations and Hall mobilities are obtained from Hall Effect measurements, which provide further insight into the electrical conductivity and Seebeck coefficient mechanisms. The thermal conductivity of thin film filled skutterudite was found to be much less compared with bulk Yb filled CoSb{sub 3} skutterudite. In this work, the 1020 K heat treatment was adopted for thin film post process due to the high degree of crystallinity as well as avoiding reverse heating effect. Thin film samples of different thicknesses were prepared with the same sputtering deposition rate and maximum ZT of 0.48 was achieved at 700 K for the 130 nm thick sample. This value was between half and one third of the bulk figure of merit which was due to the lower Hall mobility.

36 MATERIALS SCIENCE↗

CERN’s Linac4 H{sup −} sources: Status and operational results

Two volume sources equipped with DESY and CERN plasma generators and a low voltage electron dump were operated at 45 kV in the Linac4 tunnel and on a dedicated test stand. These volume sources delivered approximately 20 mA and ensured the commissioning of the Radio Frequency Quadrupole accelerator and of the first section of the Drift Tube Linac. CERN’s prototype of a cesiated surface source equipped with this electron dump was operated continuously from November 2013 to April 2014 on the ion source test stand and is being commissioned in the Linac4 tunnel. Before cesiation, the prototype conditioned in volume mode provided up to 30 mA H{sup −} beam. Short cesiations, of the order of 10 mg effectively reduced the intensity of co-extracted electrons down to 2 - 8 times the H{sup −} current; this cesiated surface operation mode delivered up to 60 mA H{sup −} beam. An H{sup −} beam of the order of 40 mA was sustained up to four weeks operation with 500 μs pulses at 1.2s spacing. A new extraction was designed to match these beam properties. A copy of BNL’s magnetron produced at CERN was tested at BNL and delivered at 40 kV H{sup −} beam exceeding Linac4’s nominal intensity of 80 mA. In this contribution, the performances, dynamic response to cesiation, stability and availability of these prototypes are described. The needed optimization of the emittance of H{sup −} beam above 40 mA is presented, which requires an evolution of the front end that encompasses implementation of a large ceramic insulator.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Metal negative ion beam extraction from a radio frequency ion source

A metal ion source of magnetron magnetic field geometry has been designed and operated with a Cu hollow target. Radio frequency power at 13.56 MHz is directly supplied to the hollow target to maintain plasma discharge and induce self-bias to the target for sputtering. The extraction of positive and negative Cu ion beams have been tested. The ion beam current ratio of Cu{sup +} to Ar{sup +} has reached up to 140% when Ar was used as the discharge support gas. Cu{sup −} ion beam was observed at 50 W RF discharge power and at a higher Ar gas pressure in the ion source. Improvement of poor RF power matching and suppression of electron current is indispensable for a stable Cu{sup −} ion beam production from the source.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗