Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Wettability, structural and optical properties investigation of TiO{sub 2} nanotubular arrays

Graphical abstract: FESEM images of the TiO 2 nanotube layers formed at 0.5 wt% NH4F/ glycerol. - Highlights: • Structural property investigation of TiO{sub 2} nanotube. • Evaluation of wettability of TiO{sub 2} nanotube. • Study on optical properties of TiO{sub 2} nanotube. • The effect of anatase phase on optical and wettability properties of TiO{sub 2.} - Abstract: In this study, the effect of microstructural evolution of TiO{sub 2} nanotubular arrays on wettability and optical properties was investigated. Pure titanium was deposited on silica glass by PVD magnetron sputtering technique. The Ti coated substrates were anodized in an electrolyte containing NH{sub 4}F/glycerol. The structures of the ordered anodic TiO{sub 2} nanotubes (ATNs) as long as 175 nm were studied using field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD). The result shows a sharp peak in the optical absorbance spectra around the band gap energy, 3.49–3.42 eV for annealed and non-annealed respectively. The thermal process induced growth of the grain size, which influence on the density of particles and the index of refraction. Furthermore, the wettability tests' result displays that the contact angle of intact substrate (θ = 74.7°) was decreased to 31.4° and 17.4° after anodization for amorphous and heat treated (450 °C) ANTs coated substrate, respectively.

36 MATERIALS SCIENCE↗

Ti{sub 2}AlN thin films synthesized by annealing of (Ti+Al)/AlN multilayers

Highlights: • Epitaxial thin films of the MAX phase Ti{sub 2}AlN are obtained by thermal annealing. • A new metastable (Ti,Al,N) solid solution with the structure of α-T is evidenced. • The formation of the MAX phase occurs at low temperature (600 °C). - Abstract: Single-phase Ti{sub 2}AlN thin films were obtained by annealing in vacuum of (Ti + Al)/AlN multilayers deposited at room temperature by magnetron sputtering onto single-crystalline (0001) 4H-SiC and (0001) Al{sub 2}O{sub 3} substrates. In-situ X-ray diffraction experiments combined with ex-situ cross-sectional transmission electron microscopy observations reveal that interdiffusion processes occur in the multilayer at a temperature of ∼400 °C leading to the formation of a (Ti, Al, N) solid solution, having the hexagonal structure of α-Ti, whereas the formation of Ti{sub 2}AlN occurs at 550–600 °C. Highly oriented (0002) Ti{sub 2}AlN thin films can be obtained after an annealing at 750 °C.

36 MATERIALS SCIENCE↗

Investigation of CrMnV and CrMnTiV multi principal element alloys thin films for use as exit windows of electron beam accelerators

Here, this study explores CrMnV and CrMnTiV multi principal element alloy (MPEA) films as candidates for electron beam exit windows in industrial, high-power accelerators. Films were deposited via magnetron sputtering on various substrates and exposed to 66 kGy of 10 MeV e-beam irradiation. Structural and mechanical properties were analyzed using FESEM, XRD, and nanoindentation. CrMnTiV films exhibited superior grain uniformity and hardness, regardless of the substrate type. Compared to bulk materials, both MPEA films demonstrated higher hardness and excellent radiation resistance. These results highlight the potential of MPEA films as durable, radiation-tolerant materials for high-performance accelerator exit window applications.

Electron Beam Irradiation↗

The microstructure and He + ion irradiation behavior of novel low-activation W-Ta-Cr-V refractory high entropy alloy for nuclear applications

Microstructure and nanohardness of a nearly equimolar W-Ta-Cr-V high entropy alloy (HEA), as well as its irradiation response under He + irradiation, were investigated. The single-phase body-centered cubic nanostructured alloy with a 1 µm thick layer was fabricated on a silicon substrate using a magnetron sputtering method. The HEA film has a complex microstructure consisting of micrometric domains that exhibit internal nanostructure controlled by their crystal orientation. The measured nanohardness of the W-Ta-Cr-V alloy is 13 ± 2 GPa, which significantly exceeds the hardness of nanocrystalline tungsten as a result of the high solid-solution strengthening effect. In order to evaluate the irradiation resistance of the HEA film, the material was irradiated with 200 keV He + ions at room temperature, with two different ion fluences: 1 × 10 16 and 5 × 10 16 ions/cm 2 . Using transmission electron microscopy, a high density of extremely fine He bubbles is observed that were uniformly distributed in the matrix. The increase of He + ion fluence increased the density of bubbles, whereas their size remained at a similar level, which indicates that the damage proceeds by the nucleation of additional He bubbles, not by their growth.

36 MATERIALS SCIENCE↗

Durability enhancement of all-solid-state electrochromic devices by adjusting the charge density ratio between electrochromic and counter electrode layers

Here, owing to an increase in global warming, smart-window devices based on charge-balanced electrochromic devices (ECDs), which exhibit high potential to increase the thermal efficiency of buildings, have gained prominence. However, studies on the fabrication and cycling stability of charge-balanced ECDs are scarce. In this study, WO 3 and NiO x films were deposited on indium-tin-oxide (ITO)-coated glass substrates by reactive direct-current magnetron sputtering, and the deposition time was varied to control the thickness and charge density of the thin films. Subsequently, the NiO x /ITO/glass and WO 3 /ITO/glass substrates were laminated with a Li-based polymeric electrolyte to fabricate all-solid-state ECDs comprising electrochromic (EC) and counter-electrode (CE) layers in charge-density ratios of 12.6, 6.4, 2.3, and 1.1. Changes in the electrochromic properties, device-layer microstructure, crystal structure, and elemental composition of the as-constructed ECDs before and after degradation were investigated to understand the influence of the charge-density ratio of the EC and CE layers on the long-term durability of ECDs. Increasing the charge-density ratio decreased the cycling stability of the device owing to changes in the microstructure and crystal structure of the NiO x layer in the microstructural deep-trap sites. Among all the ECDs, those comprising EC and CE layers with similar charge densities showed the most stable optical modulation and highest long-term durability. Finally, based on the aforementioned results, a degradation mechanism for charge-imbalanced all-solid-state ECDs was proposed. This study is expected to open new frontiers in designing optimal-performance electrochemical devices with a wide variety of potential applications.

14 SOLAR ENERGY↗

Effect of the addition of Si into V 2 O 5 coatings: Structure and tribo-mechanical properties

Vanadium oxide (V2O5) is one of the lubricious oxides with the potential to be used as a solid lubricant at elevated temperatures. However, the material itself is not hard wear-resistant, so most of the research has focused on adding V into hard nitride coatings that could lead to the formation of a self-lubricating V(2)O(5)layer when heated. The other possible solution, which has been less studied, is to look for mechanisms to enhance the hardness of the oxide coating. In this research, we investigate the effect of the addition of Si into the V2O5 coatings, aiming to find conditions that lead to enhance hardness and/or reduced wear while keeping the high temperature lubricity of the V2O5 structure. For this, Si modified V2O5 coatings were deposited using a dual magnetron sputtering system. The results showed that small additions of Si (< 2.0 at%) improved the hardness of the V2O5 coatings up to 5 times while keeping the same temperature dependence of the coefficient of friction than V2O5. Dry sliding experiments using the pin-on-disc configuration against silicon nitride balls were performed at 25, 300 and 600 degrees C. Wear factors in the 10(-7) mm(3)/Nm range were obtained, indicating a good wear resistance. Further addition of Si into the V2O5 structure led to a loss of the crystalline ordering and a significant reduction in the hardness.

Hall-Petch↗

Correlating high temperature mechanical and tribological properties of CrAlN and CrAlSiN hard coatings

CrAlN and CrAlSiN hard coatings deposited by magnetron sputtering were analyzed for their high temperature mechanical and tribological properties. High temperature nanoindentation measurements on both coatings were performed from room temperature up to 700 °C in steps of 100 °C where a reduction in hardness H and elastic modulus E* from their initial values was noticed. In addition, high temperature tribological tests were conducted in inert atmosphere in the same temperature range to obtain information about the coefficient of friction and the wear coefficient. In order to link the tribological behavior to the obtained mechanical properties, the H/E* ratio was calculated and compared to the high temperature wear from the current and other studies with similar coatings. Finally, the evolution of the mechanical and tribological properties at high temperature is discussed based on the current knowledge available in literature.

Drnovšek, Aljaž↗

High temperature fracture toughness of single-layer CrAlN and CrAlSiN hard coatings

Hardness and toughness are among of the most important physical properties of hard coatings and it is important to analyze them at temperatures present during coating applications. CrAlN and CrAlSiN are hard coating materials frequently used in high temperature applications. Here, while both possess high oxidation resistance and thermal stability, they differ in their microstructure. In this work, the fracture toughness of magnetron-sputtered single-layer CrAlN and CrAlSiN hard coatings was determined up to 700 °C by in-situ scanning electron microscopy micro-cantilever deflection tests. The results show a decreasing trend of the fracture toughness with increasing temperature. While both coatings' fracture toughness trends are similar up to 400 °C, they diverge at higher temperatures. In general, the evolution of the fracture toughness with increasing temperature shows similarities to the observed changes in hardness in the same temperature range.

36 MATERIALS SCIENCE↗

Adhesion, structure, and mechanical properties of Cr HiPIMS and cathodic arc deposited coatings on SiC

Chromium deposited by high-power impulse magnetron sputtering (HIPIMS) versus cathodic arc (CA) processes exhibits very different mechanical properties. Combining the two can result in a single-phase with superior performance that can be tailored for use in coating SiC for advanced nuclear fuel cladding. Coating morphology, residual stress, elemental depth profiles, and mechanical testing by scratch, pull-off adhesion, and microcantilevers are shown for HiPIMS, CA, and combined coatings. CA coatings were likely to spall and had lower adhesion strength due to tensile residual stresses but had desirable material properties. Additionally, by depositing an initial layer of Cr by HiPIMS followed by a layer of Cr by CA, a more adherent coating was achieved and some of the stress issues with CA morphology were resolved. Combined coatings withstood at least 80 MPa in pull-off adhesion tests and had maximum failure stress values of 5GPa in microcantilever tests. These results were better than either individual deposition method and point to a hybrid approach being a path forward for a more robust coating.

36 MATERIALS SCIENCE↗

Modes of strain accommodation in Cu-Nb multilayered thin film on indentation and cyclic shear

Two-phase layered thin films with a high density of semi-coherent interfaces exhibit excellent mechanical properties and thermal stability. Here, in this study, a magnetron-sputtered Cu-Nb dual-layered thin film (~500 nm for Cu and ~150 nm for Nb) having an amorphous interface between Cu and Nb with a high density of aligned growth twins in Cu is subjected to severe surface deformation. The material is loaded using indentation and cyclic shear under tribological testing. The strain accommodation in the subsurface microstructure after deformation varies based on the local structure and deformation mode. Grain refinement and crack formations in the stressed region of the Nb layer and localized crystallization of the amorphous interface are observed after indentation and scratch testing. Pronounced detwinning of growth twins in the Cu layer under the cyclic shear strain leaves large dislocations sites and loops which are observed both by high-resolution transmission electron microscopy and experiment-guided molecular dynamic (MD) simulations. Our simulations provided insights into understanding the pathway for the detwinning process under cyclic shear loading.

36 MATERIALS SCIENCE↗

Residual stress characterization of Al/SiC nanoscale multilayers using X-ray

Nanolayered composites are used in a variety of applications such as wear resistant coatings, thermal barrier coatings, optical and magnetic thin films, and biological coatings. Residual stresses produced in these materials during processing play an important role in controlling their microstructure and properties. In this paper, we have studied the residual stresses in model metal-ceramic Al/SiC nanoscale multilayers produced by physical vapor deposition (magnetron sputtering). X-ray synchrotron radiation was used to measure stresses in the multilayers using the sin{sup 2} {Psi} technique. The stresses were evaluated as a function of layer thicknesses of Al and SiC and also as a function of the number of layers. The stress state of Al in the multilayer was largely compressive, compared to single layer Al stresses. This is attributed to a peening mechanism due to bombardment of the Al layers by SiC and Ar neutrals during deposition. The stress evolution was numerically modeled by a simplified peening process to qualitatively explain the Al thickness-dependent residual stresses.

36 MATERIALS SCIENCE↗

Surface studies of crystalline and amorphous Zn-In-Sn-O transparent conducting oxides

X-ray and ultraviolet photoelectron spectroscopy (UPS) studies were made of in situ RF magnetron-sputtered crystalline (c) and amorphous (a) Zn–In–Sn–O (ZITO) thin films, ex situ pulsed laser deposited c- and a-ZITO thin films, and bulk ZITO ceramics. Cosubstitution of Zn and Sn for In results in an increase of the In core level binding energy at a given Fermi level compared to that measured in undoped and Sn-doped In 2 O 3 (ITO). In plots of work function vs. Fermi level, in situ c-ZITO and a-ZITO films have low ionization potentials (7.0–7.7 eV) that are similar to undoped In 2 O 3 . In contrast, dry-air-annealed in situ films, ex situ films, and bulk ceramics have higher ionization potentials (7.7–8.1 eV) that are more similar to ITO and match well with previous work on air-exposed surfaces. Kelvin Probe measurements were made of select a-ZITO films exposed to air and ultraviolet/ozone-treated so as to measure work functions under conditions commonly employed for device fabrication. Results (4.8–5.3 eV) were in good agreement with the UPS work functions of oxygen-exposed materials and with literature values. Lastly, a parallelogram plot of work function vs. Fermi level shows that a wider range of work functions is achievable in ZITO materials as compared to other transparent conducting oxides (Sb-doped SnO 2 , Al-doped ZnO, Sn-doped In 2 O 3 ), making ZITO more versatile for applications.

Proffit, Diana E↗

Influence of hydrostatic pressure on superconducting properties of niobium thin film

We have studied superconducting properties of niobium thin films under hydrostatic pressures up to 3 GPa. The films with thickness of 100 nm were prepared in the high vacuum DC magnetron sputtering system (with critical temperature TC = 8.95 K at ambient pressure). The produced high quality films have been characterized using electrical resistivity and magnetization measurements, X-ray diffraction, and atomic force microscope imaging. We have observed increase of TC with increasing value of applied pressure (dTC/dp = 73 mK/GPa) up to 3 GPa. This observation is different to pressure effect observed on bulk sample of Nb. In this paper we are discussing the origin of this discrepancy. (C) 2014 Elsevier B.V. All rights reserved.

Pristáš, Gabriel↗

Reactive multilayers fabricated by vapor deposition. A critical review

The reactive multilayer thin films are a class of energetic materials that continue to attract attention for use in joining applications and as igniters. Generally composed of two reactants, these heterogeneous solids can be stimulated by an external source to promptly release stored chemical energy in a sudden emission of light and heat. In our critical review article, results from recent investigations of these materials are discussed. Discussion begins with a brief description of the vapor deposition techniques that provide accurate control of layer thickness and film composition. More than 50 reactive film compositions have been reported to date, with most multilayers fabricated by magnetron sputter deposition or electron-beam evaporation. In later sections, we review how multilayer ignition threshold, reaction rate, and total heat are tailored via thin film design. For example, planar multilayers with nanometer-scale periodicity exhibit rapid, self-sustained reactions with wavefront velocities up to 100 m/s. Numeric and analytical models have elucidated many of the fundamental processes that underlie propagating exothermic reactions while demonstrating how reaction rates vary with multilayer design. Recent, time-resolved diffraction and imaging studies have further revealed the phase transformations and the wavefront dynamics associated with propagating chemical reactions. Many reactive multilayers (e.g., Co/Al) form product phases that are consistent with published equilibrium phase diagrams, yet a few systems, such as Pt/Al, develop metastable products. The final section highlights current and emerging applications of reactive multilayers. Examples include reactive Ni(V)/Al and Pd/Al multilayers which have been developed for localized soldering of heat-sensitive components.

36 MATERIALS SCIENCE↗

Indium doped Cd1-xZnxO alloys as wide window transparent conductors

We have synthesized Indium doped Cd 1-x Zn x O alloys across the full composition range using magnetron sputtering method. The crystallographic structure of these alloys changes from rocksalt (RS) to wurtzite (WZ) when the Zn content is higher than 30%. The rocksalt phase alloys in the composition range 0 < x < 0.3 can be efficiently n-type doped, shifting the absorption edge to 3.25 eV and reducing resistivity to about 2.0 × 10 -4 Ω-cm. Here, we found that In doped CdO (ICO) transmits more solar photons than commercial fluorine doped tin oxide (FTO) with comparable sheet conductivity. The infrared transmittance is further extended to longer than 1500 nm wavelengths by depositing the In doped Cd 1-x Zn x O in ~ 1% of O 2 . This material has a potential for applications as a transparent conductor for silicon and multi-junction solar cells.

36 MATERIALS SCIENCE↗

Tribological performance of quaternary CrSiCN coatings under dry and lubricated conditions

This paper presents an experimental study of friction and wear performance of quaternary CrSiCN coatings deposited on a hardened H-13 steel substrate by a plasma enhanced magnetron sputtering (PEMS) technique. Friction and wear tests were conducted with a reciprocating line contact between a hardened 4370 steel roller and coated and uncoated flat specimens under dry and lubricated conditions. The effects of coating thickness (1, 3.5 and 7.5 μm) on the mechanical properties, friction and wear performance were also assessed. In dry sliding, the friction of coated surfaces was about the same as for uncoated surfaces, except for the 1-μm coating, which had higher friction. Friction for coated surfaces under lubricated contact was in general higher than for uncoated surfaces. There was no measurable wear on any of the coated surfaces, under either dry or lubricated conditions. However, wear was higher on the steel roller counterface sliding against the coated surfaces, with the amount of wear proportional to the mating coating thickness. The effectiveness of formulated lubricant additives was also modified by the coating, resulting in major effects on friction and wear behavior. Finally, this reduction in lubricant additive efficacy is due to the fact that the additives were designed and optimized for ferrous surfaces.

36 MATERIALS SCIENCE↗