SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Thermally insulated glove contains short, closely-spaced elastomeric pins that insulate without impairing flexibility. By confining pins to the inter-joint areas of palm, fingers and back of the hand, joint mobility is retained. Glove thermal-insulation requirements dictate the relationships among pin length, pin diameter, and number of pins per unit surface length.
Results of computer analysis of effects of various manifold insulation detailed in 23-page report show that if fluid is distributed to and gathered from array of solar collectors by external rather than internal manifold, effectiveness of manifold insulation has major influence on efficiency. Report describes required input data and presents equations that govern computer model. Provides graphs comparing collector efficiencies for representative manifold sizes and insulations.
The primary insulation system used to protect the space shuttle orbiter on reentry is an externally attached, rigidized, fibrous silica which has been machined into tiles. The tiles constitute the temperature reusable surface insulation system and are used on over 70 percent of the vehicle exterior surface where peak temperatures range from 400 to 1260 C. Cargon-carbon leading edges are used in areas where peak temperatures exceed 1650 C and a felt flexible insulation is used in regions below 400 C. Approximately 32,000 tiles are used in the HRST system and because of vehicle configuration, aerodynamic requirements, and weight considerations no two tiles are alike. Fabrication and quality control procedures are described.
A method of installing fragile, light-weight, high-temperature fiber insulation, particularly where the insulation is to be used as a seal strip providing a high order of thermal barrier insulation is described. The process is based on provision of a strip of the mineral batting cut oversize by a predetermined amount, saturated in a fugitive polymer solution, compressed in a mold, dried and cured to form a rigidized batting material which may be machined to required shape. The machined dimensions would normally be at least nominally less than the dimensions of the cavity to be sealed. After insertion in the cavity, which may be a wire-mesh seal enclosure, the apparatus is subjected to baking at a temperature sufficiently high to cause the resin to burn off cleanly, leaving the batting substantially in its original condition and expanded into the cavity or seal enclosure.
Glass marbles improve temperature control. Modified vacuum laminator for photovoltaic solar arrays includes thermal insulation made of conventional glass marbles. Marbles serve as insulation for temperature control of lamination process at cure temperatures as high as 350 degrees F. Used to replace original insulation made of asbestos cement.
Two possible techniques for reducing the external pressure required to induce the insulator-metal transition in solid hydrogen are described. One uses impurities to lower the energy of the metallic phase relative to that of the insulating phase. The other utilizes a negative pressure induced in the insulating phase by electron-hole pairs, created either with laser irradiation or pulsed synchrotron sources.
A method of installing fragile, light weight, high temperature fiber insulation, particularly where the insulation is to be used as a seal strip providing a high order of thermal barrier insulation is discussed. The process is based on provision of a strip of the mineral batting cut oversize by a predetermined amount, saturated in a fugitive polymer solution, compressed in a mold, dried and cured to form a rigidized batting material which is machined to required shape. The machine dimensions would normally be at least nominally less than the dimensions of the cavity to be sealed. After insertion in the cavity, which may be a wire-mesh seal enclosure, the apparatus is subjected to baking at a temperature sufficiently high to cause the resin to burn off cleanly, leaving the batting substantially in its original condition and expanded into the cavity or seal enclosure.
Nondestructive high voltage test techniques (mostly electrical methods) are studied to prevent total or catastrophic breakdown of insulation systems under applied high voltage in space. Emphasis is on the phenomenon of partial breakdown or partial discharge (P.D.) as a symptom of insulation quality, notably partial discharge testing under D.C. applied voltage. Many of the electronic parts and high voltage instruments in space experience D.C. applied stress in service, and application of A.C. voltage to any portion thereof would be prohibited. Suggestions include: investigation of the ramp test method for D.C. partial discharge measurements; testing of actual flight-type insulation specimen; perfect plotting resin samples with controlled defects for test; several types of plotting resins and recommendations of the better ones from the electrical characteristics; thermal and elastic properties are also considered; testing of commercial capaciters; and approximate acceptance/rejection/rerating criteria for sample test elements for space use, based on D.C. partial discharge.
An advanced flexible reusable surface insulation material for future space shuttle flights was investigated. A conventional fly shuttle loom with special modifications to weave an integral double layer triangular core fabric from quartz yarn was used. Two types of insulating material were inserted into the cells of the fabric, and a procedure to accomplish this was developed. The program is follow up of a program in which single layer rectangular cell core fabrics are woven and a single type of insulating material was inserted into the cells.
Crystallized water vapor fills voids in pipe insulation. Small, carefully controlled amount of water vapor introduced into dry nitrogen gas before it enters aft fuselage. Vapor freezes on pipes, filling cracks in insulation. Ice prevents gaseous nitrogen from condensing on pipes and dripping on structure, in addition to helping to insulate all parts. Industrial applications include large refrigeration plants or facilities that use cryogenic liquids.
A method and a system for testing the bonding of foam insulation attached to metal is described. The system involves the use of an impacter which has a calibrated load cell mounted on a plunger and a hammer head mounted on the end of the plunger. When the impacter strikes the insulation at a point to be tested, the load cell measures the force of the impact and the precise time interval during which the hammer head is in contact with the insulation. This information is transmitted as an electrical signal to a load cell amplifier where the signal is conditioned and then transmitted to a fast Fourier transform (FFT) analyzer. The FFT analyzer produces energy spectral density curves which are displayed on a video screen. The termination frequency of the energy spectral density curve may be compared with a predetermined empirical scale to determine whether a igh quality bond, good bond, or debond is present at the point of impact.
Existing radiation response data for 130 materials of the synthetic organic insulation and dielectric class are analyzed, and thresholds and 25-percent change dose levels for these materials are presented. Both the lowest reported threshold dose (LTD) and the 25-percent change dose level are found to vary widely among the different insulators (used as spacecraft components). The LTD is tabulated to indicate the levels where radiation effects become apparent. These level are of use in setting a lower limit where changes can be expected, and could be used to exempt synthetic insulation and dielectrics from radiation considerations when the environments are substantially below this limit. Cautions to be observed in applying the data to current problems are presented.
A method and apparatus for testing the tensile strength and bonding strength of sprayed-on foam insulation attached to metal cryogenic fuel tanks is described. A circular cutter is used to cut the insulation down to the surface of the metal tank to form plugs of the insulation for testing in situ on the tank. The apparatus comprises an electromechanical pulling device powered by a belt battery pack. The pulling device comprises a motor driving a mechanical pulling structure comprising a horizontal shaft connected to two bell cracks which are connected to a central member. When the lower end of member is attached to a fitting, which in turn is bonded to a plug, a pulling force is exerted on the plug sufficient to rupture it. The force necessary to rupture the plug or pull it loose is displayed as a digital read-out.
Aluminum oxide coatings have been investigated as electrically insulating layers for mounting thin film Pt-Pt/Rh thermocouples on gas turbine blade and vane alloys (MAR M200 + Hf and MAR M509). Thermal oxides were grown directly onto NiCoCrAlY and FeCrAlY coatings on these alloys at temperature between 1300 and 1400 K in oxygen partial pressures 10 to the -7th to 2 x 10 to the 4th Pa. Although these thermal oxides exhibited good adherence, analytical characterizations using electron and optical microscopy, as well as X-ray photoelectron spectroscopy showed that they had defects and impurities which limited their insulating ability. The insulating quality of the coating was greatly improved however by reactively sputtering an aluminum oxide film over the thermal oxide. Results are presented on the electrical performance of the 2-5 micron thick composite layers for temperatures up to 1300 K.
Operating high-voltage solar arrays in the space environment can result in anomalously large currents being collected through small insulation defects. Tests simulating the electron collection have shown that there are two major collection modes. The first involves current enhancement by means of a surface phenomenon involving secondary electron emission from the surrounding insulator. In the second mode, the current collection is enhanced by vaporization and ionization of the insulator material, in addition to the surface enhancement of the first mode. The electron collection due to surface enhancement (first mode) has been modeled. Using this model, simple calculations yield realistic predictions.
Attention is given to a light weight foam insulation system applicable to reusable cryogenic propellant tankage for hypersonic aircraft and space launch vehicles. The insulation system consists of nominally sized blocks of a high temperature-resistant polymethacrylimide foam that is wrapped with a vapor-impermeable membrane of Kapton-aluminum-Kapton laminate, which is adhesively bonded to the outer propellant tank wall. Test results are presented which indicate that this insulation system is capable of enduring a Mach 5 service environment without structural cracking, deterioration, or loss of performance.
Finite-difference models are used to study the effects of insulation by the megaregolith on lunar thermal evolution. Results indicate that the megaregolith has two important influences on heat flow: (1) Because the megaregolith is exceptionally thin in mare regions, heat passes more readily through them than through highland regions, and even flows laterally from the highland toward the mare. As a result, heat flow is exceptionally high along a boundary between highland and mare regions. (2) On a global scale, megaregolith insulation combined with lithosphere insulation causes slow cooling, which as a cumulative effect results in high present-day mantle temperatures and heat flow. Assuming that the global mean megaregolith thickness is 2 km, a heat flow of 12 mW/sq m is best matched by models with bulk moon U contents of 20-21 ng/g. Independent constraints on lunar internal temperatures derived from magnetic and tectonic data are best matched by models with about 14 ng/g U. Thus the bulk moon U content is roughly 17 ng/g. These results imply that the bulk moon contents of U, and related refractory lithophile elements such as Th, Al, Ca, etc., must be considerably lower than commonly assumed.
Work during Phase 3 of a program aimed at developing a comprehensive heat transfer and thermal analysis methodology for design analysis of insulated diesel engines is described. The overall program addresses all the key heat transfer issues: (1) spatially and time-resolved convective and radiative in-cylinder heat transfer, (2) steady-state conduction in the overall structure, and (3) cyclical and load/speed temperature transients in the engine structure. These are all accounted for in a coupled way together with cycle thermodynamics. This methodology was developed during Phases 1 and 2. During Phase 3, an experimental program was carried out to obtain data on heat transfer under cooled and insulated engine conditions and also to generate a database to validate the developed methodology. A single cylinder Cummins diesel engine was instrumented for instantaneous total heat flux and heat radiation measurements. Data were acquired over a wide range of operating conditions in two engine configurations. One was a cooled baseline. The other included ceramic coated components (0.050 inches plasma sprayed zirconia)-piston, head and valves. The experiments showed that the insulated engine has a smaller heat flux than the cooled one. The model predictions were found to be in very good agreement with the data.