Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “IMPINGEMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

A digital communications system for manned spaceflight applications.

A highly efficient, all-digital communications signal design employing convolutional coding and PN spectrum spreading is described for two-way transmission of voice and data between a manned spacecraft and ground. Variable-slope delta modulation is selected for analog/digital conversion of the voice signal, and a convolutional decoder utilizing the Viterbi decoding algorithm is selected for use at each receiving terminal. A PN spread spectrum technique is implemented to protect against multipath effects and to reduce the energy density (per unit bandwidth) impinging on the earth's surface to a value within the guidelines adopted by international agreement. Performance predictions are presented for transmission via a TDRS (tracking and data relay satellite) system and for direct transmission between the spacecraft and earth. Hardware estimates are provided for a flight-qualified communications system employing the coded digital signal design.

Batson, B. H.↗
NASA NTRS1973

A visual study of radial inward choked flow of liquid nitrogen.

Data and high speed movies were acquired on pressurized subcooled liquid nitrogen flowing radially inward through a 0.0076 cm gap. The stagnation pressure ranged from 0.7 to 4 MN/sq m. Steady radial inward choked flow appears equivalent to steady choked flow through axisymmetric nozzles. Transient choked flows through the radial gap are not uniform and the discharge pattern appears as nonuniform impinging jets. The critical mass flow rate data for the transient case appear different from those for the steady case. On the mass flow rate vs pressure map, the slope and separation of the isotherms appear to be less for transient than for steady radial choked flow.

Hendricks, R. C.↗
NASA NTRS1973

Condensation in CO2 free jet expansions. II - Growth of small clusters.

An investigation into the kinetics of molecular clustering processes which occur in the highly supersaturated vapor of a CO2 free jet is described. Terminal cluster concentrations in expansions from room temperature and reservoir pressures in the range from 400 to 900 torr were determined for trimeric CO2 for nozzle diameters of .0076 cm, .015 cm, and .023 cm and in the case of CO2 tetramer and pentamer for .015 cm nozzle diameter. The measurements were made mass spectrometrically in a supersonic molecular beam apparatus. A kinetic analysis was developed from an extension of the critical nucleus concept of nucleation theory and rate equations based on intermolecular collisions. The observed cluster populations could be accounted for by the theory by adopting sticking probabilities of approximately .03 for monomer impinging on dimer, trimer, and tetramer.

Dorfeld, W. G.↗
NASA NTRS1973

Correlation of ion and beam current densities in Kaufman thrusters.

In the absence of direct impingement erosion, electrostatic thruster accelerator grid lifetime is defined by the charge exchange erosion that occurs at peak values of the ion beam current density. In order to maximize the thrust from an engine with a specified grid lifetime, the ion beam current density profile should therefore be as flat as possible. Knauer (1970) has suggested this can be achieved by establishing a radial plasma uniformity within the thruster discharge chamber; his tests with the radial field thruster provide an example of uniform plasma properties within the chamber and a flat ion beam profile occurring together. It is shown that, in particular, the ion density profile within the chamber determines the beam current density profile, and that a uniform ion density profile at the screen grid end of the discharge chamber should lead to a flat beam current density profile.

Wilbur, P. J.↗
NASA NTRS1974

Control vane for engine exhaust flow

Vane solves problem of hot-gas exhaust impingement on curved-duct exteriors, shielding, and other nearby structure components. To eliminate secondary egress of exhaust, curved vane is placed upstream of engine exhaust duct and in close proximity to exhaust exit to induce free-stream flow more in line with exit.

Shaw, C. S.↗
NASA NTRS1973

Effect of exhaust nozzle configuration on aerodynamic and acoustic performance of an externally blown flap system with a quiet 6:1 bypass ratio engine

A highly suppressed TF-34 engine was used to investigate engine and flap interaction noise associated with an externally blown flap STOL powered lift system. Noise, efficiency, and velocity decay characteristics of mixed and separate flow exhaust systems including convergent, co-annular, and lobed designs were determined with the engine operating alone. Noise data were then obtained for several of the exhaust configurations with the engine blowing a wing-flap segment. Noise for both the engine alone and the engine with blown flaps showed substantial differences for the various exhaust configurations tested. The differences in observed noise are related primarily to nozzle effective exhaust velocity, flap impingement velocity, and noise spectral shape.

Samanich, N. E.↗
NASA NTRS1973

Effect of gage size on the measurement of local heat flux

General formulas are derived for determining gage averaging errors of strip-type heat flux meters used in the measurement of one-dimensional heat flux distributions. In addition, a correction procedure is presented which allows a better estimate for the true value of the local heat flux. As an example of the technique, the formulas are applied to the cases of heat transfer to air slot jets impinging on flat and concave surfaces. It is shown that for many practical problems, the use of very small heat flux gages is often unnecessary.

Baumeister, K. J.↗
NASA NTRS1973

Noise tests on an externally blown flap with the engine in front of the wing

Noise tests were conducted with a nozzle exhausting over a small scale model of an externally blown flap (EBF) lift-augmentation system, with exhaust impingement on the wing leading edge. Two series of tests were conducted: with wing leading edge inside the nozzle; and with leading edge set back from the nozzle exit plane 1 diameter on the jet axis. The results indicated no significant differences in spectral shape, level, or directivity pattern. Static lift and thrust tests were conducted on the same model indicated considerable flow attachment on both configurations, with slightly greater attachment and turning for the wing outside the nozzle. Finally, a comparison with engine-above- and engine-below-the-wing EBF's tested by previous investigators shows the acoustic performance of the configurations tested for this report to lie between the other two.

Karchmer, A. M.↗
NASA NTRS1973

Off-center-line shock interference heating patterns on basic shapes in hypersonic flows

The results of an experimental study of off-center-line shock-interference heating on basic shapes at hypersonic speeds are presented. The study covered three types of shock-interference patterns over a range of nominal Mach numbers (6 to 20), specific heat ratios (1.40 and 1.67), free-stream Reynolds numbers(8 million to 26 million per meter), and impinging shock strengths. Heat-transfer rates higher than stagnation levels were measured over much of the off-center-line model surface. Peak heating up to 17 times the stagnation heating was measured.

Keyes, J. W.↗
NASA NTRS1973

Wind tunnel investigation of a large-scale 25 deg swept-wing jet transport model with an external blowing triple-slotted flap

An investigation has been conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an externally blown triple-slotted flap. The lift of the model was augmented by the turbofan engine exhaust impingement on the flap surface. The model had a 25 deg swept wing of aspect ratio 7.28 and four turbofan engines. The model was tested with two flap extents. One extended from 0.11 to 1.00 of the wing semispan, and the other extended from 0.11 to 0.75 of the wing semispan with a single-slotted aileron from 0.75 to 1.00 of the wing semispan. The results were obtained for several flap deflections with and without the horizontal tail at gross thrust coefficients from 0 to 4.0. Longitudinal and lateral data are presented with three and four engines operating.

Aoyagi, K.↗
NASA NTRS1974

Effect of configuration variation on externally blown flap noise

The sensitivity of flap interaction noise to variations in engine-under-the-wing externally blown flap geometry was investigated with a large cold-flow model. Both 2- and 3-flap wing sections (7-ft chord) with trailing flap angles up to 60 deg were employed. Exhaust nozzles included coaxial, plug, and 8- and 13-inch diameter conical configurations. These nozzles were tested at two positions below the wing. The effects of these geometry variations on noise level, directivity, and spectral shape are summarized in terms of exhaust flow parameters evaluated at the nozzle exit and at the flap impingement station. The results are also compared with limited flap noise data available from tests using real engines.

Dorsch, R. G.↗
NASA NTRS1973

Precipitation

Precipitation is usually defined as all forms of hydrometeors, liquid or solid, which are free in the atmosphere and which reach the ground. In this report the definition is extended to those hydrometeors which do not reach the ground, but impinge on a flying surface, such as space vehicles. Accumulation is reported in depth over a horizontal surface; i.e., millimeters or inches for the liquid phase and in depth or equivalent depth of water equivalent for the frozen phase.

Source record↗
NASA NTRS1974

Acoustic characteristics of externally blown flap systems with mixer nozzles

Noise tests were conducted on a large scale, cold flow model of an engine-under-the-wing externally blown flap lift augmentation system employing a mixer nozzle. The mixer nozzle was used to reduce the flap impingement velocity and, consequently, try to attenuate the additional noise caused by the interaction between the jet exhaust and the wing flap. Results from the mixer nozzle tests are summarized and compared with the results for a conical nozzle. The comparison showed that with the mixer nozzle, less noise was generated when the trailing flap was in a typical landing setting (e.g., 60 deg). However, for a takeoff flap setting (20 deg), there was little or no difference in the acoustic characteristics when either the mixer or conical nozzle was used.

Goodykoontz, J. H.↗
NASA NTRS1973

Vertical axis wind rotors: Status and potential

The design and application of a vertical axis wind rotor is reported that operates as a two stage turbine wherein the wind impinging on the concave side is circulated through the center of the rotor to the back of the convex side, thus decreasing what might otherwise be a high negative pressure region. Successful applications of this wind rotor to water pumps, ship propulsion, and building ventilators are reported. Also shown is the feasibility of using the energy in ocean waves to drive the rotor. An analysis of the impact of rotor aspect ratio on rotor acceleration shows that the amount of venting between rotor vanes has a very significant effect on rotor speed for a given wind speed.

Vance, W.↗
NASA NTRS1974

Some injector element detail effects on screech in hydrogen-oxygen rockets

An experimental investigation was conducted to learn more about how the specific details of a concentric tube injection element affect the screech characteristics of a hydrogen-oxygen rocket engine. The four variables investigated were (1) impingement angle, (2) oxidizer tube blunt base thickness, (3) oxidizer tube recess and extension, and (4) oxidizer tube-annulus concentricity. Tests were made using a 27.34-cm (10.77-in.) diameter heat sink combustor at nominally 300-psia chamber pressure. All of the test variables were investigated using a 157 element circular pattern injector. Additional oxidizer tube recess tests were made with a 421 element hexagonal pattern injector. Tests were conducted over the oxidant-fuel ratio range of 4 to 6. Stability evaluation for each configuration was made using the hydrogen temperature rating technique. Several element configurations were also cold flow tested using nitrogen and water as simulants. The element detail changes resulted in changes in hydrogen injector pressure drop even though the physical injection area was constant for all similar tests in both hot firing and cold flow tests. These changes in injector pressure drop produced changes in combustion stability. The data were correlated with a modified version of a previously reported injection area ratio correlation. By interpreting changes in injector pressure drop as changes in injector hydrogen flow resistance, the data were compared with a hydrogen flow response stability model and were found to be in agreement.

Hannum, N. P.↗
NASA NTRS1974

Experiments on confined turbulent jets in cross flow

Results are reported of experiments on the effects of an opposite wall on the characteristics of turbulent jets injected into a cross flow, for unheated and heated jets. Longitudinal and transverse distributions of velocity and temperature are presented for single and multiple circular jets, and trajectories are presented for two-dimensional jets. The opposite wall has relatively little effect on a single jet unless the ratio of jet to cross flow momentum flux is large enough for the jet to impinge on the opposite wall. For a row of jets aligned perpendicularly to the cross flow, the opposite wall exerts progressively larger influence as the spacing between jets decreases. Much of the effect of jet and wall proximity can be understood by considering the interaction of the vortex flow which is the major feature of the structure of a single jet in a cross flow. Smoke photographs are shown to elucidate some of the interaction patterns.

Kamotani, Y.↗
NASA NTRS1974

Flight prototype regenerative particulate filter system development

The effort to design, fabricate, and test a flight prototype Filter Regeneration Unit used to regenerate (clean) fluid particulate filter elements is reported. The design of the filter regeneration unit and the results of tests performed in both one-gravity and zero-gravity are discussed. The filter regeneration unit uses a backflush/jet impingement method of regenerating fluid filter elements that is highly efficient. A vortex particle separator and particle trap were designed for zero-gravity use, and the zero-gravity test results are discussed. The filter regeneration unit was designed for both inflight maintenance and ground refurbishment use on space shuttle and future space missions.

Green, D. C.↗
NASA NTRS1974

Performance of LI-1542 reusable surface insulation system in a hypersonic stream

The thermal and structural performance of a large panel of LI-1542 reusable surface insulation tiles was determined by a series of cyclic heating tests using radiant lamps and aerothemal tests in the Langley 8-foot high-temperature structures tunnel. Aerothermal tests were conducted at a free-stream Mach number of 6.6, a total temperature of 1830 K, Reynolds numbers of 2.0 and 4,900,000 per meter, and dynamic pressures of 29 and 65 kPa. The results suggest that pressure gradients in gaps and flow impingement on the header walls at the end of longitudinal gaps are sources for increased gap heating. Temperatures higher than surface radiation equilibrium temperature were measured deep in gaps and at the header walls. Also, the damage tolerance of the LI-1542 tiles appears to be very high. Tile edge erosion rate was slow; could not be tolerated in a shuttle application. Tiles soaked with water and subjected to rapid depressurization and aerodynamic heating showed no visible evidence of damage.

Hunt, L. R.↗