Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HARDNESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Radiation hardened PMOS process with ion implanted threshold adjust

By including specific process modifications the effect of ion implantation on radiation hardness can be minimized and radiation hard ion implanted MOS circuits can be fabricated. The experimental procedure followed was to examine key processing steps (with respect to radiation hardness) on ion-implanted individual PMOS transistors. The individual transistors were evaluated by continuously monitoring the threshold voltage as the transistors were being irradiated. By comparing runs it was possible to deduce what is considered a radiation hard ion implanted process. Tests with a complex LSI PMOS IC processor chip containing over 2000 transistors and resistors were also conducted

Jhabvala, M.↗

Energetic electrons, Type III radio bursts, and impulsive solar flare X-rays

Observations of impulsive hard X-ray and type III radio bursts made during the maximum of the last solar activity cycle are analyzed. Spectral measurements of 10-68 keV X-rays were made with the University of California (Berkeley) experiment aboard the OGO 5 satellite. About 20% of impulsive hard X-ray bursts are correlated with type III radio bursts, whereas only about 3% of the reported type III radio bursts are correlated with impulsive X-ray bursts. The location of the associated H gamma flare on the solar disk has little effect on the X-ray-type III burst correlation. The magnitude of the X-ray-type III burst correlation increases systematically with an increase in the intensity and starting frequency of the radio burst, the peak energy and hardness of the X-ray burst, and the peak nonthermal emission measure and spectral hardness of the electron spectrum not less than 20 keV inside the X-ray source. Observations are consistent with the electron populations responsible for both the X-ray and type III emissions accelerated in a single acceleration process; they also suggest a flare model where the primary instability causing electron acceleration during the impulsive phase occurs in the corona.

Kane, S. R.↗

Influence of mineral oil and additives on microhardness and surface chemistry of magnesium oxide (001) surface

X-ray photoelectron spectroscopy analyses and hardness experiments were conducted with cleaved magnesium oxide /001/ surfaces. The magnesium oxide bulk crystals were cleaved into specimens along the /001/ surface, and indentations were made on the cleaved surface in laboratory air, in nitrogen gas, or in degassed mineral oil with and without an additive while not exposing specimen surface to any other environment. The various additives examined contained sulfur, phosphorus, chlorine, or oleic acid. The sulfur-containing additive exhibited the highest hardness and smallest dislocation patterns evidencing plastic deformation; the chlorine-containing additive exhibited the lowest hardness and largest dislocation patterns evidencing plastic deformation. Hydrocarbon and chloride (MgCl2) films formed on the magnesium oxide surface. A chloride film was responsible for the lowest measured hardness.

Miyoshi, K.↗

Thermal vacuum testing of flexible radiator systems

Flexible fin radiators are being developed to meet spacecraft requirements of light weight, compact launch volume, modular growth, reusability, and the capability of an on-orbit deployment and retraction. Two prototype versions of deployable/retractable, flexible finspace radiators (soft and hard tube) were tested simultaneously under thermal vacuum conditions. A map of the heat rejection performance of each radiator panel under various environmental conditions is given. The soft tube radiator deployment system demonstrated minimal gas pressure and was capable of maintaining partial deployment; temperature control was achieved by varying the deployment length. The radiator could be recovered after an inadvertant freezing of the coolant in the Teflon tube. The hard tube radiator deployment mechanism performed adequately throughout the testing, but did exhibit some undesirable performance characteristics. The hard tube radiator pressure drop was higher than expected, but was not affected by the length of deployment. The radiator operated at less than full deployment, and the manifolds were found to have a significant effect on heat rejection. At low-load conditions, the hard tube radiator appeared to bypass its deployed area.

Rankin, G.↗

Comparison of theoretically predicted and observed Solar Maximum Mission X-ray spectra for the 1980 April 13 and May 9 flares

A method for predicting the hard X-ray spectrum in the 10-100 keV range for compact flares during their initial rise is developed on the basis of a thermal model. Observations of the flares of 1980 April 13, 4:05 U.T., and 1980 May 9, 7:12 U.T. are given and their combined spectra from the Hard X-ray Burst Spectrometer and Hard X-ray Imaging Spectrometer on the Solar Maximum Mission are deduced. Constraints on the cross sectional area of the supposed emitting arch are obtained from data from the Hard X-ray Imaging Spectrometer. A power-law spectrum is predicted for the rise of the flare of April 13 for initial arch densities less than 10 to the 10th per cu cm and also for the flare of May 9 for initial arch densities less than 5.4 x 10 to the 10th per cu cm. In both cases power-law spectra are observed. Limitations and implications of these results are discussed.

Smith, D. F.↗

The impact of mismatch on the performance of coded narrow-band FM with limiter/discriminator detection

An examination of the impact of mismatch on the performance of convolutionally encoded/Viterbi decoded narrow-band FM with limiter/discriminator detection is presented. Attention was given to the potential gain available by the combination of this type of system in terms of hard and soft decision decoding. Soft decision decoding was demonstrated to offer only approximately 0.3 dB better performance than hard decision coding. It was also shown, through a technique involving the number of clicks occurring in each detection interval, that both soft and hard decision decoding bit error probability performance could be improved. It is concluded that the mismatch between the coding channel and the decoding metric of the Viterbi algorithm is responsible for reducing the difference between hard and soft decoding metrics.

Simon, M. K.↗

Observation of chromospheric evaporation during the Solar Maximum Mission

A study is presented of the upward motions of part of the soft X-ray emitting plasma using data for flares collected in 1980 by the Bent Crystal Spectrometer and the Hard X-ray Burst Spectrometer on the Solar Maximum Mission satellite. Results show that upward motions of the soft X-ray plasma are temporally associated with the build up of the thermal phase of flares and with the period of energy deposition as indicated by the hard X-ray emission. In addition, it is found that the hardness of the hard X-ray spectrum, the evaporation velocity, and the rate of increase of the gradual phase are correlated. It is also possible that the total electron energy deposited in the chromosphere, the peak emission measure of the evaporating plasma, and the peak emission measure of the thermal coronal plasma may also be correlated.

Antonucci, E.↗

Characteristics of gamma-ray line flares

Observations of solar gamma rays by the Solar Maximum Mission (SMM) demonstrate that energetic protons and ions are rapidly accelerated during the impulsive phase. To understand the acceleration mechanisms for these particles, the characteristics of the gamma ray line flares observed by SMM were studied. Some very intense hard X-ray flares without detectable gamma ray lines were also investigated. Gamma ray line flares are distinguished from other flares by: (1) intense hard X-ray and microwave emissions; (2) delay of high energy hard X-rays; (3) emission of type 2 and/or type 4 radio bursts; and (4) flat hard X-ray spectra (average power law index: 3.1). The majority of the gamma ray line flares shared all these characteristics, and the remainder shared at least three of them. Positive correlations were found between durations of spike bursts and spatial sizes of flare loops as well as between delay times and durations of spike bursts.

Bai, T.↗

Decimetric gyrosynchrotron emission during a solar flare

A decimetric, microwave, and hard X-ray burst was observed during a solar flare in which the radio spectrum below peak flux fits an f+2 power law over more than a decade in frequency. The spectrum is interpreted to mean that the radio emission originated in a homogeneous, thermal, gyrosynchrotron source. This is the first time that gyrosynchrotron radiation has been identified at such low decimetric frequencies (900-998) MHz). The radio emission was cotemporal with the largest single hard X-ray spike burst ever reported. The spectrum of the hard X-ray burst can be well represented by a thermal bremsstrahlung function over the energy range from 30 to 463 keV at the time of maximum flux. The temporal coincidence and thermal form of both the X-ray and radio spectra suggest a common source electron distribution. The unusual low-frequency extent of the single-temperature thermal radio spectrum and its association with the hard X-ray burst imply that the source had an area approx. 10(18) sq cm a temperature approx 5x10(8) K, an electron density approx. 7.10(9) cu cm and a magnetic field of approx. 120 G. H(alpha) and 400-800 MHz evidence suggest that a loop structure of length 10,000 km existed in the flare active region which could have been the common, thermal source of the observed impulsive emissions.

Batchelor, D. A.↗

The states of Cygnus X-1

HEAO 3 High Resolution Gamma-Ray Spectrometer observations of Cygnus X-1 in the 48-300 keV range, along with correlated 3-6 keV Ariel 5 data, have led to the identification of a new state for this object with low flux in both the soft and hard X-ray regions. This is followed by a slow increase in the hard X-ray flux to the normal low state of the source, characterized by a low intensity soft X-ray emission and a high intensity hard X-ray emission. The new 'superlow' state is interpreted in terms of the Compton model, where the X-ray emission arises from the scattering of low energy photons and one-billion K hot electrons. The superlow state may be seen as one extreme of a continuum of low state behavior, given that Compton cooling should begin to quench the hot electrons at higher soft X-ray fluxes, giving rise to the softer X-ray spectrum and to the anticorrelation in changes in the soft and hard X-ray fluxes.

Ling, J. C.↗

The impulsive phase of a solar limb flare

The limb flare of 1980 November 18 at 14:51 UT is studied with the X-ray instruments on board the Solar Maximum Mission (SMM). Evidence is found for release of a significant fraction, 10 percent or more, of the flare energy before the impulsive hard X-ray burst. In the impulsive phase the hard X-rays emitted during the rapidly varying part of the burst are observed on the limb, at a level consistent with the chromosphere. During the final stages of the hard X-ray burst, when the fast time structure has disappeared, the hard X-rays clearly come from the corona, at which time the spectrum is softer. Throughout the decay phase of the flare the X-rays also originate in the corona. It is concluded that initially the flare energy is deposited below the transition zone, from which point the chromospheric plasma is ablated. When this plasma has expanded into the corona to the energy release site, particle acceleration associated with such energy release is quenched. The altitude of this site is estimated at 6000 + or - 1500 km above the photosphere. The sequence of observations is consistent with the bulk of the energy being contained in suprathermal protons, in the energy region 100-1000 keV, during the impulsive phase.

Simnett, G. M.↗

Characteristics of gamma-ray line flares

Observations of solar gamma rays by the Solar Maximum Mission (SMM) demonstrate that energetic protons and ions are rapidly accelerated during the impulsive phase. To understand the acceleration mechanisms for these particles, the characteristics of the gamma ray line flares observed by SMM were studied. Some very intense hard X-ray flares without detectable gamma ray lines were also investigated. Gamma ray line flares are distinguished from other flares by: (1) intense hard X-ray and microwave emissions; (2) delay of high energy hard X-rays, (3) emission of type 2 and/or type 4 radio bursts; and (4) flat hard X-ray spectra (average power law index: 3.1). The majority of the gamma ray line flares shared all these characteristics, and the remainder shared at least three of them. Positive correlations were found between durations of spike bursts and spatial sizes of flare loops as well as between delay times and durations of spike bursts.

Bai, T.↗

Ultraviolet observations of solar flares from the Solar Maximum Mission

The results of observations of solar flares, obtained by means of the UV Spectrophotometer and Polarimeter (UVSP) instrument on board the Solar Maximum Mission satellite are summarized and discussed. The results are grouped into three main topics: (1) plasma diagnostics in the flare transition zone plasmas, (2) spatial and temporal evolutions of the UV and hard X-ray bursts, and (3) energy release processes in the impulsive phase. The methods of spectral UV analysis, comparison with the hard X-ray burst results, and the interpretation of the results are summarized. It is concluded that the energy release processes in the flare phase can be best interpreted in terms of multiple large and small interloops interacting with each other either mechanically or inductively. Furthermore, the majority of impulsive UV and hard X-ray bursts occurs in small compact loops with high densities and transition-zone temperatures. The impulsive hard X-ray and UV bursts are emitted by nonthermal particles, accelerated by the loop interactions and impinging on the footpoints of these loops.

Cheng, C.-C.↗

Rapid soft X-ray fluctuations in solar flares observed with the X-ray polychromator

Three flares observed by the Soft X-Ray Polychromator on the Solar Maximum Mission were studied. Flare light curves from the Flat Crystal Spectrometer and Bent Crystal Spectrometer were examined for rapid signal variations. Each flare was characterized by an initial fast (less than 1 min) burst, observed by the Hard X-Ray Burst Spectrometer (HXRBS), followed by softer gradual X-ray emission lasting several minutes. From an autocorrelation function analysis, evidence was found for quasi-periodic fluctuations with rise and decay times of 10 s in the Ca XIX and Fe XXV light curves. These variations were of small amplitude (less than 20%), often coincided with hard X-ray emissions, and were prominent during the onset of the gradual phase after the initial hard X-ray burst. It is speculated that these fluctuations were caused by repeated energy injections in a coronal loop that had already been heated and filled with dense plasma associated with the initial hard X-ray burst.

Zarro, D. M.↗

Indentation plasticity and fracture in silicon

Measurements of the ductile-brittle transition temperature of heavily doped silicon were carried out using indentation techniques. Diamond pyramid hardness tests were performed on the (100) face of heavily doped N-type and P-type and intrinsic silicon single crystals. Tests were performed over the range 200 C to 850 C and loads of 100 to 500 g were used. Samples were subsequently etched to reveal dislocation rosettes produced by indentation. Intrinsic silicon underwent a ductile-brittle transition at 660 C, P-type at 645 C and N-type at 625 C. Hardness values varied from 1.1 GPa at 700 C to 11.7 GPa at 200 C. Significant effects of hardness on doping were present only at the highest temperatures. Lower loads generally produced higher hardness but load did not affect the Ductile-Brittle Transition Temperature (DBTT). Fracture toughness values ranged from 0.9 MPa m(1/2) at 200 C to 2.75 MPa m(1/2) near the DBTT. Doping did not affect the fracture toughness of silicon. P-type doping increased the size of dislocation rosettes observed after indentation, but N-type did not, in contradiction of the expected results. Results are discussed in terms of the effect of doping on the dislocation mobility in silicon.

Rybicki, George C.↗

Development of a high-speed H-alpha camera system for the observation of rapid fluctuations in solar flares

A solid-state digital camera was developed for obtaining H alpha images of solar flares with 0.1 s time resolution. Beginning in the summer of 1988, this system will be operated in conjunction with SMM's hard X-ray burst spectrometer (HXRBS). Important electron time-of-flight effects that are crucial for determining the flare energy release processes should be detectable with these combined H alpha and hard X-ray observations. Charge-injection device (CID) cameras provide 128 x 128 pixel images simultaneously in the H alpha blue wing, line center, and red wing, or other wavelength of interest. The data recording system employs a microprocessor-controlled, electronic interface between each camera and a digital processor board that encodes the data into a serial bitstream for continuous recording by a standard video cassette recorder. Only a small fraction of the data will be permanently archived through utilization of a direct memory access interface onto a VAX-750 computer. In addition to correlations with hard X-ray data, observations from the high speed H alpha camera will also be correlated and optical and microwave data and data from future MAX 1991 campaigns. Whether the recorded optical flashes are simultaneous with X-ray peaks to within 0.1 s, are delayed by tenths of seconds or are even undetectable, the results will have implications on the validity of both thermal and nonthermal models of hard X-ray production.

Kiplinger, Alan L.↗

BATSE flare observations in Solar Cycle 22

The Hard X-Ray Burst Spectrometer (HXRBS) group at GSFC has developed and is maintaining a quick-look analysis system for solar flare hard x-ray data from the Burst and Transient Source Experiment (BATSE) on the recently launched Compton Gamma-Ray Observatory (GRO). The instrument consists, in part, of 8 large planar detectors, each 2025 sq cm, placed on the corners of the GRO spacecraft with the orientation of the faces being those of a regular octahedron. Although optimized for the detection of gamma-ray bursts, these detectors are far more sensitive than any previous spacecraft-borne hard x-ray flare instrumentation both for the detection of small microflares and the resolution of fine temporal structures. The data in this BATSE solar data base are from the discriminator large area (DISCLA) rates. From each of eight detectors there are hard x-ray data in four energy channels, 25-50, 50-100, 100-300, and greater than 300 keV with a time resolution of 1.024 seconds. These data are suitable for temporal correlation with data at other wavelengths, and they provide a first look into the BATSE and other GRO instrument flare data sets. The BATSE and other GRO principle investigator groups should be contacted for the availability of data sets at higher time or spectral resolution or at higher energies.

Schwartz, R. A.↗

Maxwell's second- and third-order equations of transfer for non-Maxwellian gases

Condensed algebraic forms for Maxwell's second- and third-order equations of transfer are developed for the case of molecules described by either elastic hard spheres, inverse-power potentials, or by Bird's variable hard-sphere model. These hardly reduced, yet exact, equations provide a new point of origin, when using the moment method, in seeking approximate solutions in the kinetic theory of gases for molecular models that are physically more realistic than that provided by the Maxwell model. An important by-product of the analysis when using these second- and third-order relations is that a clear mathematical connection develops between Bird's variable hard-sphere model and that for the inverse-power potential.

Baganoff, D.↗