SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Flight tests of cross, modified ringsail, and disk-gap-band parachute deployment performance from low altitudes with structural load data
The operating characteristics of a nonlinear envelope-limiting device were investigated at extreme flight conditions by using a real time digital aircraft spin simulation and flight tests of a scale model remotely piloted research vehicle. A digital mechanization of the F-15 control system, including the stall inhibiter, was used in the simulation and in the control system of the scale model. The operational characteristics of the stall inhibiter and the effects of the stall inhibiter on the spin susceptibility of the airplane were investigated.
An assessment is given of results from a 17-flight evaluation of the F100 Engine Model Derivative (EMD) powerplant in an F-15 fighter. The EMD variant of the F100 engine incorporates a larger fan, a higher temperature turbine, a digital control system, and a 16-segment afterburner. These modifications result in a 15 to 20 percent increase in thrust which is exhibited in the reduction of F-15 acceleration time to Mach 2.0 by 23 percent. The only uncorrected shortcoming of the engine upon completion of the 17-flight test course was the occurrence of compressor stalls at the throttle's idle setting. These stalls had not been predicted by either ground facility tests or compressor stability assessments.
Flight test maneuvers are specified for the F-18 High Alpha Research Vehicle (HARV). The maneuvers were designed for closed loop parameter identification purposes, specifically for lateral linear model parameter estimation at 30, 45, and 60 degrees angle of attack, using the Actuated Nose Strakes for Enhanced Rolling (ANSER) control law in Strake (S) model and Strake/Thrust Vectoring (STV) mode. Each maneuver is to be realized by applying square wave inputs to specific pilot station controls using the On-Board Excitation System (OBES). Maneuver descriptions and complete specification of the time/amplitude points defining each input are included, along with plots of the input time histories.
Flight tests were conducted to determine the effect of length of a conical windshield on the drag of a bluff body moving at supersonic speeds. A comparison is made between results obtained and results of previous drag tests of body-windshield combinations.The effect of increasing the length of the windshield is discussed.
A flight test was made to determine the servoplane effectiveness and stability characteristics of the free-floating horizontal stabilizer to be used on the XF10F airplane. The results of this test indicate that servoplane effectiveness is practically constant through the speed range up to a Mach number of 1.15, and the stabilizer static stability is satisfactory. A loss of damping occurs over a narrow Mach number range near M = 1.0, resulting in dynamic instability of the stabilizer in this narrow range. Above M = 1.0 there is a gradual positive trim change of the stabilizer.
Model-based Systems Engineering (MBSE) is an emerging methodology that can be leveraged to enhance many system development processes. MBSE allows for the centralization of an architecture description that would otherwise be stored in various locations and formats, thus simplifying communication among the project stakeholders, inducing commonality in representation, and expediting report generation. This paper outlines the MBSE approach taken to capture the processes of two different, but related, architectures by employing the Systems Modeling Language (SysML) as a standard for architecture description and the modeling tool MagicDraw. The overarching goal of this study was to demonstrate the effectiveness of MBSE as a means of capturing and designing a mission systems architecture. The first portion of the project focused on capturing the necessary system engineering activities that occur when designing, developing, and deploying a mission systems architecture for a space mission. The second part applies activities from the first to an application problem - the system engineering of the Orion Flight Test 1 (OFT-1) End-to-End Information System (EEIS). By modeling the activities required to create a space mission architecture and then implementing those activities in an application problem, the utility of MBSE as an approach to systems engineering can be demonstrated.
The NASA Goddard Space Flight Center (GSFC) Global Positioning System (GPS) applications test facility has been established within the GSFC Guidance Navigation and Control Center. The GPS test facility is currently housing the Global Simulation Systems Inc. (GSSI) STR2760 GPS satellite 40-channel attitude simulator and a STR4760 12-channel navigation simulator. The facility also contains a few other resources such as an atomic time standard test bed, a rooftop antenna platform and a radome. It provides a new capability for high dynamics GPS simulations of space flight that is unique within the aerospace community. The GPS facility provides a critical element for the development and testing of GPS based technologies i.e. position, attitude and precise time determination used on-board a spacecraft, suborbital rocket balloon. The GPS simulation system is configured in a transportable rack and is available for GPS component development as well as for component, spacecraft subsystem and system level testing at spacecraft integration and tests sites. The GPS facility has been operational since early 1996 and has utilized by space flight projects carrying GPS experiments, such as the OrbView-2 and the Argentine SAC-A spacecrafts. The SAC-A pre-flight test data obtained by using the STR2760 simulator and the comparison with preliminary analysis of the GPS data from SAC-A telemetry are summarized. This paper describes pre-flight tests and simulations used to support a unique spaceborne GPS experiment. The GPS experiment mission objectives and the test program are described, as well as the GPS test facility configuration needed to verify experiment feasibility. Some operational and critical issues inherent in GPS receiver pre-flight tests and simulations using this GPS simulation, and test methodology are described. Simulation and flight data are presented. A complete program of pre-flight testing of spaceborne GPS receivers using a GPS constellation simulator is detailed.
Insect residue contamination on aircraft wings can decrease fuel efficiency in aircraft designed for natural laminar flow. Insect residues can cause a premature transition to turbulent flow, increasing fuel burn and making the aircraft less environmentally friendly. Surfaces, designed to minimize insect residue adhesion, were evaluated through flight testing on a Falcon HU-25C aircraft flown along the coast of Virginia and North Carolina. The surfaces were affixed to the wing leading edge and the aircraft remained at altitudes lower than 1000 feet throughout the flight to assure high insect density. The number of strikes on the engineered surfaces was compared to, and found to be lower than, untreated aluminum control surfaces flown concurrently. Optical profilometry was used to determine insect residue height and areal coverage. Differences in results between flight and laboratory tests suggest the importance of testing in realistic use environments to evaluate the effectiveness of engineered surface designs.
The NASA Goddard Space Flight Center (GSFC) Global Positioning System (GPS) applications test facility has been established within the GSFC Guidance Navigation and Control Center. The GPS test facility is currently housing the Global Simulation Systems Inc. (GSSI) STR2760 GPS satellite 40-channel attitude simulator and a STR4760 12-channel navigation simulator. The facility also contains a few other resources such as an atomic time standard test bed, a rooftop antenna platform and a radome. It provides a new capability for high dynamics GPS simulations of space flight that is unique within the aerospace community. The GPS facility provides a critical element for the development and testing of GPS based technologies i.e. position, attitude and precise time determination used on-board a spacecraft, suborbital rocket or balloon. The GPS simulator system is configured in a transportable rack and is available for GPS component development as well as for component, spacecraft subsystem and system level testing at spacecraft integration and test sites. The GPS facility has been operational since early 1996 and has been utilized by space flight projects carrying GPS experiments, such as the OrbView-2 and the Argentine SAC-A spacecrafts. The SAC-A pre-flight test data obtained by using the STR2760 simulator and the comparison with preliminary analysis of the GPS data from SAC-A telemetry are summarized. This paper describes pre-flight tests and simulations used to support a unique spaceborne GPS experiment. The GPS experiment mission objectives and the test program are described, as well as the GPS test facility configuration needed to verify experiment feasibility. Some operational and critical issues inherent in GPS receiver pre-flight tests and simulations using this GPS simulator, and test methodology are described. Simulation and flight data are presented. A complete program of pre-flight testing of spaceborne GPS receivers using a GPS constellation simulator is detailed.
This is a technology which depends on a morphing vehicle wingtip. It allows one to replace the use of the rudder for some vehicles with the outer ailerons for control of the Dutch Roll Mode. Description of the PTERA flight test in support of the Spanwise Adaptive Wing flight research program.
A dispersion analysis considering 3—sigma (3σ) uncertainties (or perturbations) in platform, vehicle, and environmental parameters has been performed for the first orbital flight test (OFT-1) mission. The dispersion analysis is based on the nominal trajectory for the OFT-1 reference flight profile (RFP) which is described in Reference 1. The analysis has been performed to determine state vector and performance dispersions (or variations) which result from the indicated 3σ uncertainties. The dispersions are determined at major mission events and fixed times from Liftoff (time slices). The dispersion results will be used to evaluate the capability of the vehicle to perform the mission within a 3σ Level of confidence and to determine flight performance reserves. (FPR).
A wind tunnel technique for obtaining gust frequency response functions for use in predicting the response of flexible aircraft to atmospheric turbulence is evaluated. The tunnel test results for a dynamically scaled cable supported aeroelastic model are compared with analytical and flight data. The wind tunnel technique, which employs oscillating vanes in the tunnel throat section to generate a sinusoidally varying flow field around the model, was evaluated by use of a 1/30 scale model of the B-52E airplane. Correlation between the wind tunnel results, flight test results, and analytical predictions for response in the short period and wing first elastic modes of motion are presented.
This presentation provides an overview of two recently completed human-in-the-loop simulations, conducted as part of the Unmanned Aircraft Systems (UAS) Integration in the National Airspace System (NAS) Project. These studies investigated the effects of shorter RADAR surveillance ranges on DAA system performance. They were designed to serve as a validation of the fast-time simulation work performed by other groups working on the UAS-NAS project. They were also intended to establish a baseline for the Flight Test 6 Full Mission configuration flights. Low SWaP HITL 1 examined system performance with two candidate non-cooperative DAA well clear (DWC) definitions with a RADAR declaration range of 3.5nm. Low SWaP HITL 2 looked at DAA system performance with four different RADAR declaration ranges (1.5, 2.0, 2.5, & 3.0nm) with a non-cooperative DWC definition of 450ft vertical separation and 2200ft horizontal separation. The results of each study and the implications for FT6 are discussed.
This discussion will involve the design and architecture of the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) Reentry Vehicle (RV). It will describe the structure and modular design of the RV, expounding on its various subsystems, including power and commanding, data handling and recovery, instrumentation, the inflation system, and the aeroshell. The unique launch vehicle architecture for the LOFTID mission, as a massive rideshare payload, required the development of supporting flight systems, including the Payload Adapter Separation System (PASS) and the Reentry Vehicle Payload Adapter Interface Ring (RVPAIR). To do no harm to the primary mission, the LOFTID team also designed and delivered a flightworthy Mass Simulator as risk reduction in the event the RV was not ready in time for the primary mission launch date. Various challenges and design trades will be discussed, along with a brief description of the RV performance in flight.
This discussion will involve the design and architecture of the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) Reentry Vehicle (RV). It will describe the structure and modular design of the RV, expounding on its various subsystems, including power and commanding, data handling and recovery, instrumentation, the inflation system, and the aeroshell. The unique launch vehicle architecture for the LOFTID mission, as a massive rideshare payload, required the development of supporting flight systems, including the Payload Adapter Separation System (PASS) and the Reentry Vehicle Payload Adapter Interface Ring (RVPAIR). To do no harm to the primary mission, the LOFTID team also designed and delivered a flightworthy Mass Simulator as risk reduction in the event the RV was not ready in time for the primary mission launch date. Various challenges and design trades will be discussed, along with a brief description of the RV performance in flight.
The motivation for the work is the need for an improved ability to predict takeoff noise of future commercial supersonic aircraft. The overall objective is to validate as well as improve the conversion of facility scale-model data and semi-empirical jet-noise predictions to flight noise. As a first step, the processing of data and results from an acoustics flight test are described. The next step involves the comparison of the flight acoustic data and complementary rig-test results. This will be presented in future reports. Ultimately, the goal is improved noise-prediction methods for system studies of future commercial supersonic aircraft.
Free-flight tests in the transonic speed range utilizing rocketpropelled models have been made on three pairs of 0.11-scale North American F-100 airplane wings having an aspect ratio of 3.47, a taper ratio of 0.308, 45 degree sweepback at the quarter-chord line, and thickness ratios of 31 and 5 percent to investigate the possibility of flutte r. Data from tests of two other rocket-propelled models which accidentally fluttered during a drag investigation of the North American F-100 airplane are also presented. The first set of wings (5 percent thick) was tested on a model which was disturbed in pitch by a moving tail and reached a maximum Mach number of 0.85. The wings encountered mild oscillations near the first - bending frequency at high lift coefficients. The second set of wings 9 percent thick was tested up to a maximum Mach number of 0.95 at (2) angles of attack provided by small rocket motors installed in the nose of the model. No oscillations resembling flutter were encountered during the coasting flight between separation from the booster and sustainer firing (Mach numbers from 0.86 to 0.82) or during the sustainer firing at accelerations of about 8g up to the maximum Mach number of the test (0.95). The third set of wings was similar to the first set and was tested up to a maximum Mach number of 1.24. A mild flutter at frequencies near the first-bending frequency of the wings was encountered between a Mach number of 1.15 and a Mach number of 1.06 during both accelerating and coasting flight. The two drag models, which were 0.ll-scale models of the North American F-100 airplane configuration, reached a maximum Mach number of 1.77. The wings of these models had bending and torsional frequencies which were 40 and 89 percent, respectively, of the calculated scaled frequencies of the full-scale 7-percent-thick wing. Both models experienced flutter of the same type as that experienced-by the third set of wings.