Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Electrical Systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Computational Heat Flux Analysis for HEATheR Electric Aircraft Wing Ice Protection Systems

Increased electrification of aircraft systems, a growing trend in the aircraft industry, affects subsystems that have historically been pneumatically driven by the engine. Optimized design of propulsion and power systems must account for the requirements of these subsystems. One such subsystem, the wing ice protection system, is the focus of this paper. A preliminary computational icing analysis has been conducted using the LEWICE and ANSYS FENSAP-ICE software to characterize the requirements of a thermal ice protection system for three More Electric Aircraft concepts. This paper summarizes the methodology, simulation execution, and icing conditions used for the analysis as well as discusses the results, observed trends, and impacts to system design. This initial analysis indicates that the computed heat requirements for the wing ice protection systems are not within the capabilities of known traditional systems. A discussion of potential methods for reducing the heat flow requirement by the ice protection system is included. Potential refinements to the analysis to improve the accuracy are also discussed.

Nic Heersema↗
NASA NTRS1998

Aerospace Power Systems Design and Analysis (APSDA) Tool

The conceptual design of space and/or planetary electrical power systems has required considerable effort. Traditionally, in the early stages of the design cycle (conceptual design), the researchers have had to thoroughly study and analyze tradeoffs between system components, hardware architectures, and operating parameters (such as frequencies) to optimize system mass, efficiency, reliability, and cost. This process could take anywhere from several months to several years (as for the former Space Station Freedom), depending on the scale of the system. Although there are many sophisticated commercial software design tools for personal computers (PC's), none of them can support or provide total system design. To meet this need, researchers at the NASA Lewis Research Center cooperated with Professor George Kusic from the University of Pittsburgh to develop a new tool to help project managers and design engineers choose the best system parameters as quickly as possible in the early design stages (in days instead of months). It is called the Aerospace Power Systems Design and Analysis (APSDA) Tool. By using this tool, users can obtain desirable system design and operating parameters such as system weight, electrical distribution efficiency, bus power, and electrical load schedule. With APSDA, a large-scale specific power system was designed in a matter of days. It is an excellent tool to help designers make tradeoffs between system components, hardware architectures, and operation parameters in the early stages of the design cycle. user interface. It operates on any PC running the MS-DOS (Microsoft Corp.) operating system, version 5.0 or later. A color monitor (EGA or VGA) and two-button mouse are required. The APSDA tool was presented at the 30th Intersociety Energy Conversion Engineering Conference (IECEC) and is being beta tested at several NASA centers. Beta test packages are available for evaluation by contacting the author.

Truong, Long V.↗
NASA NTRS1986

Multimegawatt nuclear electric propulsion - First order system design and performance evaluation

The development of space nuclear power supplies capable of delivering high levels of power (1 to 10 MWe) for long life (5 to 10 years) is being considered. An important potential application of these systems will be to provide power for advanced electric propulsion devices such as ion thrusters or Magneto-Plasma-Dynamic (MPD) thrusters. High-powered Nuclear Electric Propulsion (NEP) concepts based on both ion and MPD thrusters are reviewed. To allow for mission performance evaluation, power supply, power processing, and thruster subsystems are characterized for both ion and MPD propulsion systems designed for operation in the 1 to 10 MWe power range. Several proposed missions which are significantly enhanced by the performance potential of these devices are investigated. Studied missions include near-earth orbit raising, cis-lunar cargo transportation, and planetary exploration. If developed, these 1 to 10 MWe NEP systems may provide a technological base for the development of even larger propulsion systems with power levels of up to hundreds of megawatts. The potential performance and technologies associated with such ultra-high-powered NEP systems is explored.

Sercel, J. C.↗
NASA NTRS2016

Perceived Annoyance to Noise Produced by a Distributed Electric Propulsion High Lift System

Results of a psychoacoustic test performed to understand the relative annoyance to noise produced by several configurations of a distributed electric propulsion high lift system are given. It is found that the number of propellers in the system is a major factor in annoyance perception. This is an intuitive result as annoyance increases, in general, with frequency, and, the blade passage frequency of the propellers increases with the number of propellers. Additionally, the data indicate that having some variation in the blade passage frequency from propeller-to-propeller is beneficial as it reduces the high tonality generated when all the propellers are spinning in synchrony at the same speed. The propellers can be set to spin at different speeds, but it was found that allowing the motor controllers to drift within 1% of nominal settings produced the best results (lowest overall annoyance). The methodology employed has been demonstrated to be effective in providing timely feedback to designers in the early stages of design development.

Palumbo, Dan↗
NASA NTRS1975

Design of a heat pipe governed thermal control system for the Solar Electric Propulsion Stage /SEPS/

A 2200-w capacity spacecraft heat rejection system designed for the SEPS and utilizing heat pipe radiator panels has been investigated. The total thermal control system consists of two radiator panels connected to the heat source by variable conductance heat pipes (VCHP's). The system was designed to operate in the 223 to 333 temperature range. The radiators have an emittance of 0.88 at their operational temperature and a fin efficiency of approximately 80 percent. The radiators are thermally isolated from the SEPS and environment by multilayer insulation and thermal shields. Butane was selected as the working fluid for the VCHP because of its low freezing point (135), which is necessary to prevent diffusion freezeout of the liquid during the cold outbond missions. Helium was selected for the control gas. This paper describes the VCHP system, discusses the system design parameters and presents the results of the analyses.

Ruttner, L. E.↗
NASA NTRS2019

Image-Based Localization of Ultraviolet Corona

Systems and methods for identifying a fault in an electrical distribution system may include capturing an image of a corona event associated with a component of the electrical distribution system and processing the image of the corona event to identify the center and boundary of the corona event. An overlay for display with the image of the corona event may be generated, where the overlay identifying at least a center of the corona event and may be displayed to a user via a user interface device. In some cases, an unmanned aerial vehicle may comprise one or more image sensors capable of capturing the image of the corona event and communicate the images to a remote device for processing and display to the user. The image captured by the image sensors may include an ultraviolet image, a visible spectrum image, an infrared image, or a combination of image types.

Moore, Andrew J.↗
NASA NTRS1980

Preliminary results of steady state characterization of near term electric vehicle breadboard propulsion system

The steady state test results on a breadboard version of the General Electric Near Term Electric Vehicle (ETV-1) are discussed. The breadboard was built using exact duplicate vehicle propulsion system components with few exceptions. Full instrumentation was provided to measure individual component efficiencies. Tests were conducted on a 50 hp dynamometer in a road load simulator facility. Characterization of the propulsion system over the lower half of the speed-torque operating range has shown the system efficiency to be composed of a predominant motor loss plus a speed dependent transaxle loss. At the lower speeds with normal road loads the armature chopper loss is also a significant factor. At the conditions corresponding to a cycle for which the vehicle system was specifically designed, the efficiencies are near optimum.

Sargent, N. B.↗
NASA NTRS1982

A propulsion view of the all-electric airplane

Materials illustrating a presentation on electric propulsion systems are presented. The electric engine and engine/generator configurations are described and NASA's role outlined.

Wagner, R. P.↗
NASA NTRS1990

Findings of the Joint Workshop on Evaluation of Impacts of Space Station Freedom Ground Configurations

A workshop to consider the effects of various proposed Space Station Freedom (SSF) grounding schemes was held. Expert from the plasma interactions community evaluated the impacts of environmental interactions on SSF under each of three proposed grounding schemes. The choice of the grounding scheme for the SSF power system was found to have important implications for SSF design. Interactions of the SSF power system and structure with the low earth orbit (LEO) plasma differ significantly between different grounding schemes. Environmental constraints will require modification of current SSF designs under any grounding scheme. Maintaining the present negative ground scheme may compromise SSF safety, structural integrity, and electromagnetic compatibility, and will increase contamination rates over alternate schemes. Positive grounding of the array requires redesign of the primary power system. Floating the array reduces the number of circuit changes in the primary power system but adds new hardware. Maintaining the present design will affect all parts of SSF. However, no impacts were identified on SSF systems outside of the electrical power system by positively grounding or floating the array.

Ferguson, Dale C.↗
NASA NTRS1999

[X-33 Systems]

Lockheed Martin Skunk Works has compiled an Annual Performance Report of the X-33/RLV Program. This report consists of individual reports from all industry team members, as well as NASA team centers. This portion of the report is comprised of a status report of Allied-Signal Aerospace's contribution to the program. The following is a summary of the work reviewed under their portion of the agreement: (1) Communication Systems; (2) Environmental Control Systems- Active Thermal Control System (ATCS), Purge and Vent System, Hydrogen Detection System (HDS), Avionics Bay Inerting System (ABIS), and Flush Air Data System (FADS); (2) Landing Systems; (3) Power Management and Generation Systems; (4) Flight Control Actuation System (FCAS)- Electric Power Control & Distribution System (EPCDS), and Battery Power System (BPS); and (5) Vehicle Management Systems (VMS)- VMS Hardware, VMS Software Development Activities, and System Integration Laboratory (SIL).

Source record↗
NASA NTRS2016

Carbon Back Sputter Modeling for Hall Thruster Testing

Lifetime requirements for electric propulsion devices, including Hall Effect thrusters, are continually increasing, driven in part by NASA's inclusion of this technology in it's exploration architecture. NASA will demonstrate high-power electric propulsion system on the Solar Electric Propulsion Technology Demonstration Mission (SEP TDM). The Asteroid Redirect Robotic mission is one candidate SEP TDM, which is projected to require tens of thousands of thruster life. As thruster life is increased, for example through the use of improved magnetic field designs, the relative influence of facility effects increases. One such effect is the sputtering and redeposition, or back sputter, of facility materials by the high energy thruster plumes. In support of wear testing for the Hall Effect Rocket with Magnetic Shielding (HERMeS) project, the back sputter from a Hall effect thruster plume has been modeled for the NASA Glenn Research Center's Vacuum Facility 5. The predicted wear at a near-worst case condition of 600 V, 12.5 kW was found to be on the order of 1 micron/kh in a fully carbon-lined chamber. A more detailed numerical Monte Carlo code was also modified to estimate back sputter for a detailed facility and pumping configuration. This code demonstrated similar back sputter rate distributions, but is not yet accurately modeling the magnitudes. The modeling has been benchmarked to recent HERMeS wear testing, using multiple microbalance measurements. These recent measurements have yielded values on the order of 1.5 - 2 micron/kh at 600 V and 12.5 kW.

Propulsion↗
NASA NTRS1997

Electric Propulsion for Solar System Exploration

The use of ion propulsion for deep-space missions will become a reality next year with the flight of the ion-propelled New Millennium Deep Space 1 spacecraft. This paper describes a suggested roadmap for the development of advanced solar exlectric propulsion technologies based on the expectations that these technologies will provide significant benfits for projected near, and mid-term solar system exploration missions.

Electric↗
NASA NTRS1981

Study of electrical and chemical propulsion systems for auxiliary propulsion of large space systems, volume 2

The five major tasks of the program are reported. Task 1 is a literature search followed by selection and definition of seven generic spacecraft classes. Task 2 covers the determination and description of important disturbance effects. Task 3 applies the disturbances to the generic spacecraft and adds maneuver and stationkeeping functions to define total auxiliary propulsion systems requirements for control. The important auxiliary propulsion system characteristics are identified and sensitivities to control functions and large space system characteristics determined. In Task 4, these sensitivities are quantified and the optimum auxiliary propulsion system characteristics determined. Task 5 compares the desired characteristics with those available for both electrical and chemical auxiliary propulsion systems to identify the directions technology advances should take.

Smith, W. W.↗
NASA NTRS2017

Overview of NASA Electrified Aircraft Propulsion Research for Large Subsonic Transports

NASA is investing in Electrified Aircraft Propulsion (EAP) research as part of the portfolio to improve the fuel efficiency, emissions, and noise levels in commercial transport aircraft. Turboelectric, partially turboelectric, and hybrid electric propulsion systems are the primary EAP configurations being evaluated for regional jet and larger aircraft. The goal is to show that one or more viable EAP concepts exist for narrow body aircraft and mature tall-pole technologies related to those concepts. A summary of the aircraft system studies, technology development, and facility development is provided. The leading concept for mid-term (2035) introduction of EAP for a single aisle aircraft is a tube and wing, partially turbo electric configuration (STARC-ABL), however other viable configurations exist. Investments are being made to raise the TRL (Technology Readiness Level) level of light weight, high efficiency motors, generators, and electrical power distribution systems as well as to define the optimal turbine and boundary layer ingestion systems for a mid-term tube and wing configuration. An electric aircraft power system test facility (NEAT - NASA’s Electric Aircraft Testbed) is under construction at NASA Glenn and an electric aircraft control system test facility (HEIST - Hybrid-Electric Integrated Systems Testbed) is under construction at NASA Armstrong. The correct building blocks are in place to have a viable, large plane EAP configuration tested by 2025 leading to entry into service in 2035 if the community chooses to pursue that goal.

hybrid propulsion↗