Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EXIT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Design and subscale tests of a diffuser system for a Mach 4 scramjet test facility

A fixed-geometry diffuser system was designed for use in Mach 4 free-jet tests of a hydrogen-burning modular scramjet engine. The scramjet engine has a rectangular cross section that blocks up to 33 percent of the existing tunnel nozzle exit area and swept leading edges of the scramjet produce an asymmetric downward flow that sharply increases when the scramjet inlet unstarts. Effects of these conditions on the operation of the diffuser system are not accurately predictable. An experimental investigation has therefore been conducted in unheated air using a subscale model of the tunnel-scramjet-diffuser system to substantiate the design. Test results showed that the preliminary design had to be modified to obtain an acceptable configuration of the nozzle exit, test cabin, and diffuser that would provide shock-free flow at the scramjet inlet for simulated Mach 4 flight at altitudes from 16,764 to 20,422 meters.

Andrews, E. H., Jr.↗

Experimental clean combustor program: Phase 3: Turbulence measurement addendum

Airflow turbulence parameters were measured in the high pressure, high temperature flow stream leaving the compressor of an operating gas turbine engine. A water cooled hot film turbulence probe was used to determine the turbulence intensity and length scale in the compressor exit flow stream of the CF6-50 engine. Data were obtained only at idle operating conditions. At engine power levels above idle conditions, durability problems and erratic data readings were encountered with the turbulence measurement probes. Turbulence measurements were made at three radial immersions at a point 15.5 cm downstream of the compressor outlet guide vanes in the compressor exit diffuser. The passage height at this point is 5.54 cm. Data reduction was accomplished with a time-data fast Fourier transform (FFT) system. This system finds the power spectral density distribution (PSD) of a large number of data samples using a direct Fourier transform algorithm and finds the autocorrelation parameter for these data by doing an FFT analysis of the PSD curves for a series of time delay intervals.

Taylor, J. R.↗

Theoretical study of VTOL tilt-nacelle axisymmetric inlet geometries

A systematic theoretical study of VTOL tilt-nacelle inlet design parameters is reported. The parameters considered are internal-lip contraction ratio, internal-lip major-to-minor axis ratio, diffuser-exit-area to throat-area ratio, maximum diffuser wall angle and shape. Each of the inlets was analyzed at the same given flow condition of free-stream velocity, angle between the free stream and centerline of the inlet, and diffuser-exit Mach number. The effects of these geometric parameters on surface static-pressure distribution, peak surface Mach number, diffusion velocity ratio, and tendency for the inlet flow to separate are presented.

Hawk, J. D.↗

Thrust and mass flow characteristics of four 36 inch diameter tip turbine fan thrust vectoring systems in and out of ground effect

The calibration tests carried out on the propulsion system components of a 70 percent scale, powered model of a NASA 3-fan V/STOL aircraft configuration are described. The three X3/6B/T58 turbotip fan units used in the large scale powered model were tested on an isolated basis over a range of ground heights from H/D of 1.02 to infinity. A higher pressure ratio LF336/J85 fan unit was tested over a range of ground heights from 1.55 to infinity. The results of the test program demonstrated that: (1) the thrust and mass flow performance of the X376B/T58 nose lift unit is essentially constant for H/D variations down to 1.55; at H/D 1.02 back pressurization of the fan exit occurs and is accompanied by an increase in thrust of five percent; (2) a change in nose fan exit hub shape from flat plate to hemispherical produces no significant difference in louvered lift nozzle performance for height variations from H/D = 1.02 to infinity; (3) operation of the nose lift nozzle at the higher fan pressure ratio generated by the LF336/J85 fan system causes no significant change in ground proximity performance down to an H/D of 1.55, the lowest height tested with this unit; and (4) the performance of the left and right X376B/T58 lift/cruise units in the vertical lift mode remains unchanged, within plus or minus two percent for the range of ground heights from H/D = 1.02 to infinity.

Esker, D. W.↗

Directional models for analysis of earth radiation budget measurements

The determination of the radiation heat flux densities at the top of the atmosphere (30 km) for spatial scales ranging from global to regional is necessary for the conversion of satellite irradiance measurements into useful earth radiation budget information. Data reduction algorithms are required which contain assumed directional characteristics of radiation emitted and scattered from the earth-atmosphere system. The directional characteristics are defined by models which express, for a given surface element at the top of the atmosphere, the exiting flux per unit solid angle for each direction out to space as a fraction of the total hemispheric flux exiting the surface element. Both longwave and shortwave directional radiation models are analyzed. It is found that the validity of the Nimbus 2-based limb darkening curves has generally been verified for the longwave data with the exception of the Antarctic snow fields where limb brightening was noticed in the earth radiation budget data.

Suttles, J. T.↗

An experimental study of USB flap noise reduction through mean flow modification

The effect of mean flow modification on the noise production of upper surface blown flaps has been studied experimentally. Mean velocity profile at the nozzle exit was modified from the usual 'top-hat' shape to 'Gamma' and 'L'-shaped profiles. The 'L'-modification caused noise reduction around and above the peak frequency of the 'top-hat' spectrum when compared on an equal thrust per exit area basis. Modification to 'Gamma'-shaped profile resulted in a shift of the spectrum to lower frequencies and a lower overall noise reduction. These modifications alter the development of the large scale disturbances in the upper shear layer and trailing edge wake of the wall jet geometry.

Joshi, M. C.↗

Scattering of emitted radiation from inhomogeneous and nonisothermal layers

A parametric study is performed for the exiting monochromatic intensities scattered from finite plane-parallel inhomogeneous layers that are driven solely by a distribution of thermal sources. Intensities are obtained by invariantly imbedding the standard and thermal scattering functions. The single-scattering albedo and the Henyey-Greenstein phase-function parameter are varied independently, and both linear and exponential profiles are considered. Linear temperature profiles are used, including temperature inversions. The resulting intensities, as a function of the direction cosine of propagation, are discussed from a remote-sensing point of view. For an isothermal and homogeneous medium, the gross characteristics of the exiting intensity, represented by its overall slope, mean value (magnitude), and an interior maximum value, can be related to the total optical depth, single-scattering albedo, and phase function, respectively. For a homogeneous medium, linearly decreasing (in the line of sight) temperature profiles tend to obscure the phase-function information and decrease the apparent optical depth. On the other hand, linearly increasing temperature profiles tend to retain phase-function information and increase the apparent optical depth. Temperature inversion profiles give intensities very similar to those for purely linear profiles.

Bergstrom, R. W.↗

Similar explosive eruptions of lunar and terrestrial volcanoes

A mathematical model of one-dimensional, steady duct flow of a mixture of gas and small solid particles (rock), has been applied to the earth and the moon under geometrically and dynamically similar conditions to simulate explosive eruption conditions. Numerical results for equilibrium two-phase flows for lunar and terrestrial explosive eruptions under similar conditions indicate that: (1) a lunar explosive vent is much larger than the corresponding terrestrial vent, (2) the exit velocity from the lunar explosive flow may be higher than the lunar escape velocity, but the exit velocity of terrestrial explosive flow is much less than that of the lunar case (this result supports the hypothesis that Australian tektites came from the moon as a stream of a mixture of rock and gas of extremely high speed), and (3) the thermal effects on the lunar explosive flows are much larger than those of the terrestrial case.

Pai, S. I.↗

Exploratory studies of the cruise performance of upper surface blown configurations: Experimental program, high-speed pressure tests

Basic pressure data are presented which was obtained from an experimental study of upper-surface blown configurations at cruise. The high-speed (subsonic) experimental work, studying the aerodynamic effects of wing-nacelle geometric variations, was conducted around semi-span model configurations composed of diversified, interchangeable components. Power simulation was provided by high-pressure air ducted through closed forebody nacelles. Nozzle geometry was varied across size, exit aspect ratio, exit position and boattail angle. Both 3-D force and 2-D pressure measurements were obtained at cruise Mach numbers from 0.5 to 0.8 and at nozzle pressure ratios up to about 3.0. The experimental investigation was supported by an analytical synthesis of the system using a vortex lattice representation with first-order power effects. Results are also presented from a compatibility study in which a short-haul transport is designed on the basis of the aerodynamic findings in the experimental study as well as acoustical data obtained in a concurrent program. High-lift test data are used to substantiate the projected performance of the selected transport design.

Braden, J. A.↗

Computation of three-dimensional flow in turbofan mixers and comparison with experimental data

A three dimensional, viscous computer code was used to calculate the mixing downstream of a typical turbofan mixer geometry. Experimental data obtained using pressure and temperature rakes at the lobe and nozzle exit stations were used to validate the computer results. The relative importance of turbulence in the mixing phenomenon as compared with the streamwise vorticity set up by the secondary flows was determined. The observations suggest that the generation of streamwise vorticity plays a significant role in determining the temperature distribution at the nozzle exit plane.

Povinelli, L. A.↗

Investigation of ground effects on large and small scale models of a three fan V/STOL aircraft configuration

Induced lift of a subsonic, three fan, lift/cruise, V/STOL aircraft configuration was investigated using scale modes of a multimission aircraft whose design incorporates a nose mounted lift fan and two lift/cruise units located over the wing. Configuration effects were assessed for lift improvement devices, lift/cruise nozzle rails, nozzle perimeter plates, and alternate nose fan exit hubs. Tests were conducted at four model heights (H/D = 0.95, 1.53, 3.06 and 6.45, where D is the average nozzle exit diameter equal to 0.997 m.) Results are presented and discussed.

Schuster, E. P.↗

Viscosity measuring instrument

A method and apparatus are provided for enabling the measurement of the viscosity of substances, especially those containing volatiles at elevated temperatures, with greater accuracy and at less cost than before. The apparatus includes a cylinder with a narrow exit opening at one end and a piston which closely slides within the cylinder to apply force against a sample in the cylinder to force the sample through the exit opening. In order to more rapidly heat a sample the ends of the cylinder and piston are tapered and the sample is correspondingly tapered, to provide a large surface to volume ratio. A corresponding coal sample is formed by compressing particles of coal under high pressure in a mold of appropriate shape.

Feinstein, S. P.↗

Steady-state performance of J85-21 compressor at 100 percent of design speed with and without interstage rake blockage

Internal compressor instrumentation blockage effects on steady state J85-21 compressor performance at 100 percent of design speed are determined. The blockage was generated by instrumented vanes for the first three compressor stages and by removal rakes for stages 4 to 9. Individual flow passage blockages ranged up to 4.5 percent with the instrumented vanes and up to 22 percent with the removable interstage rakes. At a Reynolds number index of 1.0, pressure ratio and airflow remained unchanged with insertion of the interstage rakes, but efficiency dropped 0.3 percentage point. Compressor exit profiles, compressor stage static pressure rise coefficients, turbine exit temperature, and fuel flow are also presented.

Werner, R. A.↗

Exploratory studies of the cruise performance of upper surface blown configurations. Experimental program: Test facilities, model design instrumentation, and lowspeed, high-lift tests

The model hardware, test facilities and instrumentation utilized in an experimental study of upper surface blown configurations at cruise is described. The high speed (subsonic) experimental work, studying the aerodynamic effects of wing nacelle geometric variations, was conducted around semispan model configurations composed of diversified, interchangeable components. Power simulation was provided by high pressure air ducted through closed forebody nacelles. Nozzle geometry was varied across size, exit aspect ratio, exit position and boattail angle. Three dimensional force and two dimensional pressure measurements were obtained at cruise Mach numbers from 0.5 to 0.8 and at nozzle pressure ratios up to about 3.0. The experimental investigation was supported by an analytical synthesis of the system using a vortex lattice representation with first order power effects. Results are also presented from a compatibility study in which a short haul transport is designed on the basis of the aerodynamic findings in the experimental study as well as acoustical data obtained in a concurrent program. High lift test data are used to substantiate the projected performance of the selected transport design.

Braden, J. A.↗

Exploratory studies of the cruise performance of upper surface blown configurations

The data and major conclusions obtained from an experimental/analytical study of upper-surface blown (USB) configurations at cruise are summarized. The high-speed (subsonic) experimental work, studying the aerodynamic effects of wing-nacelle geometric variations, was conducted around semi-span model configurations composed of diversified, interchangeable components. Power simulation was provided by high pressure air ducted through closed forebody nacelles. Nozzle geometry was varied across size, exit aspect ratio, exit position and boattail angle. Both 3-D force and 2-D pressure measurements were obtained at cruise Mach numbers from 0.5 to 0.8 and at nozzle pressure ratios up to about 3.0. The experimental investigation was supported by an analytical synthesis of the system using a vortex lattice representation with first-order power effects. Results are also presented from a compatibility study in which a short-haul transport is designed on the basis of the aerodynamic findings in the experimental study as well as acoustical data obtained in a concurrent program. High-lift test data are used to substantiate the projected performance of the selected transport design.

Braden, J. A.↗

A nozzle boundary layer model including the subsonic sublayer usable for determining boundary layer effects on plume flowfields

A model for the boundary layer at the exit plane of a rocket nozzle was developed which, unlike most previous models, includes the subsonic sublayer. The equations for the flow near the nozzle exit plane are presented and the method by which the subsonic sublayer transitions to supersonic flow in the plume is described. The resulting model describes the entire boundary layer and can be used to provide a startline for method-of-characteristics calculations of plume flowfields. The model was incorporated into a method of characteristics computer program and comparisons of computed results to experimental data show good agreement. The data used in the comparisons were obtained in tests in which mass fluxes from a 22.2-N (5 lbf) thrust engine were measured at angles off the nozzle centerline of up to 150 deg. Additional comparisons were made with data obtained during tests of a 0.89-N (0.2 lbr) monopropellant thruster and from the OH-64 space shuttle heating tests. The agreement with the data indicates that the model can be used for calculating plume backflow properties.

Cooper, B. P., Jr.↗

Computation of three-dimensional flow in turbofan mixers and comparison with experimental data

A three-dimensional, viscous computer code was used to calculate the mixing downstream of a typical turbofan mixer geometry. Experimental data were obtained using pressure and temperature rakes at the lobe and nozzle exit stations. Secondary flow velocities were also obtained. These data were used to validate the computer results. An assessment was also made to determine the relative importance of turbulence in the mixing phenomenon as compared with the streamwise vorticity set up by the secondary flows. The observations suggest that the generation of streamwise vorticity appears to play a significant role in determining the temperature distribution at the nozzle exit plane.

Povinelli, L. A.↗

Flow measurements in a model swirl combustor

Flow measurements in a model combustor composed of two confined coaxial swirling jets under noncombusting conditions are presented. Mean flow results are obtained for five different flow conditions to determine the effect of outer swirl on the recirculation zone (which is used for flame stabilization under combustion conditions). As the outer swirl magnitude is first decreased from maximum counter-swirl to zero and then increased to give co-swirl conditions, the size and the reverse flow velocity in the recirculation zone diminish. Detailed time mean and fluctuating flow measurements are obtained for a co-swirl and a counter-swirl condition with a directional pitot probe and hot-wire anenometry. For these two cases, recirculation zone occurs only with counter-swirl, near the exit of the inner jet. The recirculation zone is in the form of a one celled toroidal vortex having very low swirl velocity. Axial development of fluctuation levels, energy dissipation rates and turbulence length scales are described for the two flow conditions. Spectral analysis reveals periodic oscillations in both flows. The oscillations originate from the inner jet and up to 4 harmonics are observed. The fundamental frequencies are comparable to the rotational frequencies of the inner jets at the exit which are approximately under solid body rotation. The significance of the present results for the combustion process is discussed.

Vu, B. T.↗