Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ENCAPSULATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Nanosized carriers for hydrophobic compounds based on mesoporous silica: synthesis and adsorption properties

MCM-41 type mesoporous silica particles were obtained using a template method in an alkaline medium and cetyltrimethylammonium bromide as a matrix. The structural and adsorption characteristics of the mesoporous material were studied by dynamic light scattering, scanning electron microscopy, low-temperature adsorption—desorption of nitrogen, IR spectroscopy, and simultaneous thermal analysis. It was shown that the obtained mesoporous material possesses high porosity with the specific pore volume in excess of 1 cm{sup 3} g{sup −1}. It was established that the size of silica particles does not exceed 200 nm, which is a value acceptable for the penetration of drugs through cell membranes. The optimal compositions of aqueous dispersions of MCM-41 with minimal sedimentation processes were determined. A drug (indomethacin) was encapsulated into the silica pores using the precipitation method at various temperatures (40 and 60 °C), the quantitative parameters of loading efficiency were calculated. The infl uence of temperature on the encapsulation ability was demonstrated.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2019

Al–CNT–Ni composite with significantly increased strength and hardness

Here, aluminium–carbon nanotube–nickel (Al–CNT–Ni) composite was prepared by powder metallurgy from pure Al powder and Ni-encapsulated CNT. Previously, carbon nanotubes were coated with nickel following ultraviolet-assisted electroless deposition method. Tensile strength and hardness of the composites were found to increase in proportion to the CNTs addition. For an addition of 7 wt.% Ni-coated CNTs containing 2.5 wt.% nanotubes of 8–15 nm diameter (Ni to CNT ratio was 1–0.357), resultant tensile and yield strength were increased by 129.26% and 157.48% respectively compared to pure aluminium. Hardness was also increased by 171.39%. These results were obtained while conventional sintering was followed by further consolidation by Hot Isostatic Pressing (HIP). Enhanced mechanical properties are attributed to the well dispersion of CNTs in aluminium matrix and strong interfacial bonding between CNT and aluminium. Lastly, well dispersion of CNTs and strong interfacial bonding was resulted from the uniform Ni-encapsulation as verified by red shift in Raman Spectroscopy.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Thermodynamics and kinetics of interconversion between platinum nanoparticles and cations in zeolites

In metal-containing zeolites, sintering and redispersion processes exercise control over the identity of metal site structures, but the thermodynamic and kinetic factors that influence these molecular-level processes are not completely understood. Furthermore, we assess the ability of first principles informed free energy models (for supported and unsupported nanoparticles) and kinetic models integrating Ostwald ripening with atom trapping to describe the interconversion between Pt cations and nanoparticles encapsulated in chabazite (CHA) zeolites. Density functional theory-derived thermodynamic phase diagrams show that the interconversion between cations, favored in oxidizing environments, and particles, favored in reducing environments, is fully reversible within a wide range of their respective conditions (temperatures and pressures) for CHA and several other zeolite topologies. Kinetic Monte Carlo simulations of Pt redispersion are consistent with experimentally observed redispersion kinetics of encapsulated Pt nanoparticles in CHA zeolites, and model results suggest the zeolite host imparts additional stability for Pt nanoparticles. We envision our thermodynamic and kinetic models for Pt-CHA are also capable of describing nanoparticle and cation interconversions for other zeolite frameworks under similar conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Expanded graphite for thermal conductivity and reliability enhancement and supercooling decrease of MgCl2⋅6H2O phase change material

Highlights: • MgCl{sub 2}·6H{sub 2}O/EG composite PCMs show the superior thermal transfer ability. • 83.33 wt.% of MgCl{sub 2}·6H{sub 2}O encapsulated in composite PCM was obtained. • EG and nucleating agents decreased the supercooling degree. - Abstract: Expanded graphite (EG) is considered as a promising supporter for phase change material (PCM) due to its unique porous structure and excellent heat transfer ability. In the study, EG with different mass fractions (9 wt.%, 13 wt.%, 16.67 wt.%, and 20 wt.%) was respectively blended with MgCl{sub 2}·6H{sub 2}O. The thermal conductivity data of composite PCMs with 9 wt.%, 13 wt.%, 16.67 wt.%, and 20 wt.% of EG was respectively measured to be 0.942 W/m K, 1.053 W/m K, 1.354 W/m K and 1.658 W/m K. DSC analysis showed that 16.67 wt.% of EG decreased the degree of supercooling by 29.4 °C and that the addition of 3.0 wt.% SrCO{sub 3} further decreased the degree of supercooling by 17.9 °C. The maximum encapsulation weight percentage of MgCl{sub 2}·6H{sub 2}O reached 83.33 wt.% after 30 phase change cycles without significantly reducing its latent heat value, exhibiting the relatively stable thermal reliability.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Controlled Enzyme Cargo Loading in Engineered Bacterial Microcompartment Shells

Bacterial microcompartments (BMCs) are nanometer-scale organelles with a protein-based shell that serve to colocalize and encapsulate metabolic enzymes. They may provide a range of benefits to improve pathway catalysis, including substrate channeling and selective permeability. Several groups are working toward using BMC shells as a platform for enhancing engineered metabolic pathways. The microcompartment shell of Haliangium ochraceum (HO) has emerged as a versatile and modular shell system that can be expressed and assembled outside its native host and with non-native cargo. Further, the HO shell has been modified to use the engineered protein conjugation system SpyCatcher–SpyTag for non-native cargo loading. Here, we used a model enzyme, triose phosphate isomerase (Tpi), to study non-native cargo loading into four HO shell variants and begin to understand maximal shell loading levels. We also measured activity of Tpi encapsulated in the HO shell variants and found that activity was determined by the amount of cargo loaded and was not strongly impacted by the predicted permeability of the shell variant to large molecules. All shell variants tested could be used to generate active, Tpi-loaded versions, but the simplest variants assembled most robustly. We propose that the simple variant is the most promising for continued development as a metabolic engineering platform.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Virus-Like Particles (VLPs) as a Platform for Hierarchical Compartmentalization

Hierarchically self-assembled structures are common in biology, but it is often challenging to design and fabricate synthetic analogs. The archetypal cell is defined by hierarchically organized multicompartmentalized structures with boundaries that delineate the interior from exterior environments and is an inspiration for complex functional materials. Here, we have demonstrated an approach to the design and construction of a nested protein cage system that can additionally incorporate the packing of other functional macromolecules and exhibit some of the features of a minimal synthetic cell-like material. We have demonstrated a strategy for controlled co-packaging of subcompartments, ferritin (Fn) cages, together with active cellobiose-hydrolyzing β-glycosidase enzyme macromolecules, CelB, inside the sequestered volume of the bacteriophage P22 capsid. Using controlled in vitro assembly, we were able to modulate the stoichiometry of Fn cages and CelB encapsulated inside the P22 to control the degree of compartmentalization. The co-encapsulated enzyme CelB showed catalytic activity even when packaged at high total macromolecular concentrations comparable to an intracellular environment. Here, this approach could be used as a model to create synthetic protein-based protocells that can confine smaller functionalized proto-organelles and additional macromolecules to support a range of biochemical reactions.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2017

Modular Self-Assembly of Protein Cage Lattices for Multistep Catalysis

The assembly of individual molecules into hierarchical structures is a promising strategy for developing three-dimensional materials with properties arising from interaction between the individual building blocks. Virus capsids are elegant examples of biomolecular nanostructures, which are themselves hierarchically assembled from a limited number of protein subunits. Here, we demonstrate the bio-inspired modular construction of materials with two levels of hierarchy: the formation of catalytically active individual virus-like particles (VLPs) through directed self-assembly of capsid subunits with enzyme encapsulation, and the assembly of these VLP building blocks into three-dimensional arrays. The structure of the assembled arrays was successfully altered from an amorphous aggregate to an ordered structure, with a face-centered cubic lattice, by modifying the exterior surface of the VLP without changing its overall morphology, to modulate interparticle interactions. The assembly behavior and resultant lattice structure was a consequence of interparticle interaction between exterior surfaces of individual particles and thus independent of the enzyme cargos encapsulated within the VLPs. These superlattice materials, composed of two populations of enzyme-packaged VLP modules, retained the coupled catalytic activity in a two-step reaction for isobutanol synthesis. As a result, this study demonstrates a significant step toward the bottom-up fabrication of functional superlattice materials using a self-assembly process across multiple length scales and exhibits properties and function that arise from the interaction between individual building blocks.

36 MATERIALS SCIENCE↗
DOE OSTI2012

Photophysical Studies of Ru(II)tris(2,2`-bipyridine) Confined within a Zn(II)-Trimesic Acid Polyhedral Metal-Organic Framework

The ability to confine photoactive catalysts within metal-organic framework (MOF) materials affords the opportunity to expand the functional diversity of these materials into solar based applications. Here, the confinement of Ru(II)tris(2,2'-bipyridine) (RuBpy) by a MOF material derived from Zn(II) ions and trimesic acid (hereafter, USF2) is examined. Although the encapsulated RuBpy could not be crystallographically resolved within the MOF framework, the photophysical properties of the complex are characteristic of confinement including extended triplet metal-to-ligand ( 3 MLCT) lifetime (τ ethanol = 614 ns and {τ USF2 = 1.2 μs at 25 °C) and a slight hypsochromic shift in the steady-state emission spectrum relative to RuBpy in ethanol. The extended lifetime is attributed to a deactivation of a nonradiative 3 dd that is antibonding with respect to the Ru(II)-bipyridine due to a confined molecular environment. These results represent one of the first examples of RuBpy encapsulation and photophysical characterization within a polyhedral MOF material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

Interaction of epitaxial silicene with overlayers formed by exposure to Al atoms and O{sub 2} molecules

As silicene is not chemically inert, the study and exploitation of its electronic properties outside of ultrahigh vacuum environments require the use of insulating capping layers. In order to understand if aluminum oxide might be a suitable encapsulation material, we used high-resolution synchrotron photoelectron spectroscopy to study the interactions of Al atoms and O{sub 2} molecules, as well as the combination of both, with epitaxial silicene on thin ZrB{sub 2}(0001) films grown on Si(111). The deposition of Al atoms onto silicene, up to the coverage of about 0.4 Al per Si atoms, has little effect on the chemical state of the Si atoms. The silicene-terminated surface is also hardly affected by exposure to O{sub 2} gas, up to a dose of 4500 L. In contrast, when Al-covered silicene is exposed to the same dose, a large fraction of the Si atoms becomes oxidized. This is attributed to dissociative chemisorption of O{sub 2} molecules by Al atoms at the surface, producing reactive atomic oxygen species that cause the oxidation. It is concluded that aluminum oxide overlayers prepared in this fashion are not suitable for encapsulation since they do not prevent but actually enhance the degradation of silicene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2014

Top-gate zinc tin oxide thin-film transistors with high bias and environmental stress stability

Top gated metal-oxide thin-film transistors (TFTs) provide two benefits compared to their conventional bottom-gate counterparts: (i) The gate dielectric may concomitantly serve as encapsulation layer for the TFT channel. (ii) Damage of the dielectric due to high-energetic particles during channel deposition can be avoided. In our work, the top-gate dielectric is prepared by ozone based atomic layer deposition at low temperatures. For ultra-low gas permeation rates, we introduce nano-laminates of Al{sub 2}O{sub 3}/ZrO{sub 2} as dielectrics. The resulting TFTs show a superior environmental stability even at elevated temperatures. Their outstanding stability vs. bias stress is benchmarked against bottom-gate devices with encapsulation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2014

Anisotropic charged impurity-limited carrier mobility in monolayer phosphorene

The room temperature carrier mobility in atomically thin 2D materials is usually far below the intrinsic limit imposed by phonon scattering as a result of scattering by remote charged impurities in its environment. We simulate the charged impurity-limited carrier mobility μ in bare and encapsulated monolayer phosphorene. We find a significant temperature dependence in the carrier mobilities (μ ∝ T{sup −γ}) that results from the temperature variability of the charge screening and varies with the crystal orientation. The anisotropy in the effective mass leads to an anisotropic carrier mobility, with the mobility in the armchair direction about one order of magnitude larger than in the zigzag direction. In particular, this mobility anisotropy is enhanced at low temperatures and high carrier densities. Under encapsulation with a high-κ overlayer, the mobility increases by up to an order of magnitude although its temperature dependence and its anisotropy are reduced.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

Seeded emulsion polymerization as a powerful tool for the biofunctionalization of quantum dots

With the polymer encapsulation of quantum dots via seeded emulsion polymerization we present a powerful tool for the preparation of fluorescent nanoparticles with an extraordinary stability in aqueous solution. The method of the seeded emulsion polymerization allows a straightforward and simple in situ functionalization of the polymer shell under preserving the optical properties of the quantum dots. These requirements are inevitable for the application of semiconductor nanoparticles as markers for biomedical applications. Polymer encapsulated quantum dots have shown only a marginal loss of quantum yields when they were exposed to copper(II)-ions. Under normal conditions the quantum dots were totally quenched in presence of copper(II)-ions. Furthermore, a broad range of in situ functionalized polymer-coated quantum dots were obtained by addition of functional monomers or surfactants like fluorescent dye molecules, antibodies or specific DNA aptamers. Furthermore the emulsion polymerization can be used to prepare multifunctional hybrid systems, combining different nanoparticles within one construct without any adverse effect of the properties of the starting materials.{sup 1,2}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

An isolated water droplet in the aqueous solution of a supramolecular tetrahedral cage

Water under nanoconfinement at ambient conditions has exhibited low-dimensional ice formation and liquid–solid phase transitions, but with structural and dynamical signatures that map onto known regions of water’s phase diagram. Using terahertz (THz) absorption spectroscopy and ab initio molecular dynamics, we have investigated the ambient water confined in a supramolecular tetrahedral assembly, and determined that a dynamically distinct network of 9 ± 1 water molecules is present within the nanocavity of the host. The low-frequency absorption spectrum and theoretical analysis of the water in the Ga 4 L 6 12– host demonstrate that the structure and dynamics of the encapsulated droplet is distinct from any known phase of water. A further inference is that the release of the highly unusual encapsulated water droplet creates a strong thermodynamic driver for the high-affinity binding of guests in aqueous solution for the Ga 4 L 6 12– supramolecular construct.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Rapid curing dynamics of PEG-thiol-ene resins allow facile 3D bioprinting and in-air cell-laden microgel fabrication

Thiol-norbornene photoclick hydrogels are highly efficient in tissue engineering applications due to their fast gelation, cytocompatibility, and tunability. In this work, we utilized the advantageous features of polyethylene glycol (PEG)-thiol-ene resins to enable fabrication of complex and heterogeneous tissue scaffolds using 3D bioprinting and in-air drop encapsulation techniques. We demonstrated that photoclickable PEG-thiol-ene resins could be tuned by varying the ratio of PEG-dithiol to PEG norbornene to generate a wide range of mechanical stiffness (0.5–12 kPa) and swelling ratios. Importantly, all formulations maintained a constant, rapid gelation time (<0.5 s). We used this resin in biological projection microstereolithography (BioPµSL) to print complex structures with geometric fidelity and demonstrated biocompatibility by printing cell-laden microgrids. Moreover, the rapid gelling kinetics of this resin permitted high-throughput fabrication of tunable, cell-laden microgels in air using a biological in-air drop encapsulation apparatus (BioIDEA). We demonstrated that these microgels could support cell viability and be assembled into a gradient structure. This PEG-thiol-ene resin, along with BioPµSL and BioIDEA technology, will allow rapid fabrication of complex and heterogeneous tissues that mimic native tissues with cellular and mechanical gradients. The engineered tissue scaffolds with a controlled microscale porosity could be utilized in applications including gradient tissue engineering, biosensing, and in vitro tissue models.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Development of Cu(In,Ga)Se2 Test Coupons for Potential Induced Degradation Studies

We report on the design, fabrication and accelerated testing of fully encapsulated small area coupons (approximately 7.5cm x 7.5 cm) for the purpose of researching potential induced degradation in Cu(In, Ga)Se2 based PV modules. The fabrication of these coupons enables the study of the solar cells and the materials used in PV module manufacturing such as top and bottom glass covers of different composition (soda-lime glass, high temperature glass, alkaline-free glass, etc), plastic-based top covers, ethylene vinyl acetate and edge seal encapsulation materials. The coupons can also be used to emulate framed and frameless modules that utilize either monolithically interconnected modules or singular cell type of modules. The design of the coupons, their fabrication, the materials used and their testing for 1000 hours under 85 degrees C and 85% RH conditions are presented.

14 SOLAR ENERGY↗
DOE OSTI2020

Validation of Advanced Photovoltaic Module Materials and Processes by Combined-Accelerated Stress Testing (C-AST)

Tessolar module technology was developed to allow the incorporation of 5 incremental module material innovations. Combined, these innovations may improve the efficiency and durability of the standard silicon cell module. The innovations evaluated are: electrically conductive adhesive (ECA) replacing soldering of tabbing ribbons, light-capturing ribbon (LCR), silicone encapsulant, 2 mm front glass with backsheet, and a polymer-composite module frame. Tessolar-constructed individually encapsulated cells incorporating the material innovations are used to assemble 60-cell modules. 2 x 2 cell mini-modules of the same materials were produced for combined-accelerated stress testing (C-AST). C-AST results demonstrate that the 2 x 2 cell mini-module of Tessolar construction out-performed mini-modules using both ECA with EVA and standard solder with EVA constructions in power production over 108 cycles of testing.

14 SOLAR ENERGY↗
DOE OSTI2021

Interfacial Characterization of Positive Bias Voltage Degradation in PV Modules

Degradation from high system voltage is a prevailing failure mode in fielded photovoltaic modules, and the degradation mechanism is inherently dependent on the bias polarity. Here we report the effects of positive bias. Modules under positive bias demonstrated a significant photocurrent loss caused by two routes. First, delamination and discoloration of the silicon nitride layer, leading to optical loss determined by reflectance measurements. Second, chemical discoloration of the cell gridlines and encapsulant (EVA), which is linked to an electrochemical reaction at the silver electrodes. Chemical compositional analysis using X-ray photoemission spectroscopy demonstrated that the discoloration is attributed to Ag 2 S and/or Ag 2 O. Evidence of Ag ion migration from the cell grid into the encapsulant is observed after shallow depth profiling on the EVA surface. However, Ag was not detected at the EVA/glass interface, inferring limited Ag ion transport through the EVA. The source of sulfur is believed to be ambient air, which diffused into the module through the breathable backsheet.

characterization↗
DOE OSTI2012

Development and Demonstration of an Innovative Thermal Energy Storage System for Baseload Power Generation

The objective of this project is to research and develop a thermal energy storage system (operating range 300°C - 450°C) based on encapsulated phase change materials (PCM) that can meet the utility-scale base-load concentrated solar power plant requirements at much lower system costs compared to the existing thermal energy storage (TES) concepts. The major focus of this program is to develop suitable encapsulation methods for existing low-cost phase change materials that would provide a cost effective and reliable solution for thermal energy storage to be integrated in solar thermal power plants. This project proposes a TES system concept that will allow for an increase of the capacity factor of the present CSP technologies to 75% or greater and reduce the cost to less than $20/kWht.

14 SOLAR ENERGY↗