Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Coupled Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Tardigrade, Version 1.1x

Tardigrade is a collection of functions, libraries, and stand-alone code which enables the simulation of materials using the higher-order micromorphic framework. The tools present are the interface to INL's MOOSE code which is used as the underlying FEA solver, several constitutive equations (linear elasticity, a pressure-sensitive elasto-plastic model, crystal plasticity, and additional models for geo-materials) useful for demonstration purposes and the simulation of some materials, the micromorphic filter which converts DNS information to micromorphic stress-deformation quantities, and the overlap coupling framework which enables multi-scale simulations of a coupled higher-order macroscale and a classically defined microscale.

Miller, Nathan↗
NASA NTRS2014

Evaluating the Dominant Components of Warming in Pliocene Climate Simulations

The Pliocene Model Intercomparison Project (PlioMIP) is the first coordinated climate model comparison for a warmer palaeoclimate with atmospheric CO2 significantly higher than pre-industrial concentrations. The simulations of the mid-Pliocene warm period show global warming of between 1.8 and 3.6 C above pre-industrial surface air temperatures, with significant polar amplification. Here we perform energy balance calculations on all eight of the coupled ocean-atmosphere simulations within PlioMIP Experiment 2 to evaluate the causes of the increased temperatures and differences between the models. In the tropics simulated warming is dominated by greenhouse gas increases, with the cloud component of planetary albedo enhancing the warming in most of the models, but by widely varying amounts. The responses to mid-Pliocene climate forcing in the Northern Hemisphere midlatitudes are substantially different between the climate models, with the only consistent response being a warming due to increased greenhouse gases. In the high latitudes all the energy balance components become important, but the dominant warming influence comes from the clear sky albedo, only partially offset by the increases in the cooling impact of cloud albedo. This demonstrates the importance of specified ice sheet and high latitude vegetation boundary conditions and simulated sea ice and snow albedo feedbacks. The largest components in the overall uncertainty are associated with clouds in the tropics and polar clear sky albedo, particularly in sea ice regions. These simulations show that albedo feedbacks, particularly those of sea ice and ice sheets, provide the most significant enhancements to high latitude warming in the Pliocene.

climate models↗
DOE OSTI2025

Development, validation, and verification of multi-pass thermo-mechanical welding simulations using the open-source MOOSE framework: NeT TG4 benchmark weldment

This study develops and validates a sequentially coupled thermo-mechanical welding simulation for the three-pass 316L stainless steel NeT TG4 benchmark weldment using the open-source Multiphysics Object-Oriented Simulation Environment (MOOSE) and the Nuclear Engineering Material model Library (NEML). A diffused ellipsoidal heat source was calibrated against thermocouple data and weld macrographs to accurately model the fusion zone geometry and transient thermal fields. Material hardening is represented using the Lemaitre-Chaboche mixed isotropic-kinematic hardening model, while four annealing models - no annealing, single-stage at 1050 °C and 1300 °C, and two-stage at 800 °C/1300 °C - were implemented to assess the impact of annealing models on the accuracy of the predicted welding-induced plasticity, distortions, and residual stresses. The predictions were validated against experimental measurements and benchmarked against results from commercial software, demonstrating that thermo-mechanical MOOSE welding simulations achieve comparable accuracy with enhanced computational efficiency. This work highlights the potential of using open-source finite element frameworks like MOOSE for advanced manufacturing simulations.

Ji, Wendy [Australian Nuclear Science and Technolo↗
DOE OSTI2024

Dynamic flux surrogate-based partitioned methods for interface problems

Loosely coupled partitioned methods for multiphysics problems treat each subproblem as a separate entity and advance them independently in time. In so doing these methods enable code reuse, increase concurrency and provide a convenient framework for plug-and-play multiphysics simulations. However, mathematically loosely coupled schemes are equivalent to a single step of an iterative solution method, which can compromise their accuracy and stability. We present a new data-driven partitioned method for coupled parametric PDEs that can improve upon the accuracy of traditional loosely coupled methods without incurring a performance penalty. To that end, we replace conventional field transfers across the interface by a surrogate for the dynamics of the interface flux exchanged between the subdomains. To develop this surrogate we apply dynamic mode decomposition to a non-standard staggered-in-time state, comprising the interface flux and small solution patches near the interface. The new approach shifts the main computational burden to an offline training phase, whereas application of the surrogate in the online phase amounts to a single matrix–vector multiplication. In conclusion, we provide stability analysis of the surrogate-based partitioned scheme and include numerical results that demonstrate its potential.

Dynamic mode decomposition (DMD)↗
DOE OSTI2022

Toward control co-design of utility-scale wind turbines: Collective vs. individual blade pitch control

A large-eddy simulation framework has been coupled with controller modules to systematically investigate the impacts of collective (CPC) and individual (IPC) pitch control strategies on utility-scale wind turbine energy production and fatigue loads. Wind turbine components were parameterized using an actuator surface model to simulate the rotor blades and the turbine nacelle. The baseline CPC and IPC algorithms, consisting of single-input single-output proportional–integral controllers and two integral controllers, respectively, were incorporated into the numerical framework. A series of simulations were carried out to investigate the relative performance of the two controllers under various turbulent inflow conditions, spanning hub-height velocities of 7 to 14 m/s. The numerical simulation results of this study showed that, in comparison to the CPC, the IPC controller could successfully reduce the damage equivalent loads of utility-scale turbines at regions 2 and 3 of turbine operation by about 3% and 40%, respectively, without any penalty on the power production of the turbine. It was also shown that, despite its minor impact on the turbulence kinetic energy of the wake, the IPC controller did not influence the recovery of the turbine wake.

17 WIND ENERGY↗
DOE OSTI2023

Analysis of ultrafast magnetization switching dynamics in exchange-coupled ferromagnet–ferrimagnet heterostructures

Magnetization switching in ferromagnets has so far been limited to the current-induced spin–orbit–torque effects. Recent observation of helicity-independent all-optical magnetization switching (HI-AOS) in an exchange-coupled ferromagnet–ferrimagnet (FM-FEM) heterostructures expanded the range and applicability of such ultrafast heat-driven magnetization switching. Here we report the element-resolved HI-AOS dynamics of such an exchange-coupled system, using a modified microscopic three-temperature model. We have studied the effect of (i) the Curie temperature of the FM, (ii) FEM composition, (iii) the long-range Ruderman–Kittel–Kasuya–Yosida (RKKY) exchange-coupling strength, and (iv) the absorbed optical energy on the element-specific time-resolved magnetization dynamics. The phase-space of magnetization illustrates how the RKKY coupling strength and the absorbed optical energy influence the switching time. Our analysis demonstrates that the threshold switching energy depends on the composition of the FEM and the switching time depends on the Curie temperature of the FM as well as RKKY coupling strength. Importantly, this simulation anticipates new insights into developing faster and more energy-efficient spintronics devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A comprehensive modeling method for proton exchange membrane electrolyzer development

Hydrogen attracts significant interests as an effective energy carrier that can be derived from renewable sources. Hydrogen production using a proton-exchange membrane (PEM) electrolyzer can efficiently convert renewable power via water splitting in wide scales—from large, centralized generation to on-site production. Mathematical models with multiple scales and fidelities facilitate the continuing improvements of PEM electrolyzer development to improve performance, cost, and reliability. The model scopes and methods are presented in this paper, which also introduces a comprehensive PEM electrolysis modeling tool based on computational fluid dynamics (CFD) software, ANSYS/Fluent. The modeling tool incorporates electrochemical model of a PEM electrolysis cell to simulate the performance of coupled thermal-fluid, species transport, and electrochemical processes in a product-scale cell or stack by leveraging the powerful meshing generation and CFD solver of ANSYS/Fluent. The thermal-fluid modeling includes liquid water/gas two-phase flow and simulates a PEM electrolysis cell by using Fluent user-defined functions as add-on modules accounting for PEM-specific species transport and electrochemical processes. The modeling outcomes expediate PEM electrolyzer scaling up from basic material development and laboratory testing.

08 HYDROGEN↗
DOE OSTI2025

Microreactor Automated Control System Test Bed Digital Architecture for Real-Time, Hardware-in-the-Loop Simulation

This work describes progress made towards the development of a real-time hardware-in-the-loop (HIL) test bed for non-nuclear testing of microreactor control schemes and failure modes. Non-nuclear testing is a crucial step in developing robust control algorithms for managing microreactor dynamics. The creation of an HIL simulation harnesses the realistic dynamics of physical analogue systems while additionally considering the challenges of variable communication delay. This collaborative effort between Oak Ridge National Laboratory and Idaho National Laboratory has resulted in a LabVIEW-based gRPC communication protocol which couples a TRANSFORM Modelica simulation of nuclear components to the ViBRANT physical hardware for realistic feedback and visual representation of control action in real time. A modular python client structure is developed to manage FMU-based Modelica simulation and real-time gRPC communication. HIL testing suggests that the modeled reactor with natural convection molten salt loop coolant configuration responds well to PID control of drum positioning for modulation of reactor core power, however, future efforts will be made to explore the added thermal inertial delay of system level control and downstream demand changes. Development of this platform with a generalized methodology provides a foundation for exploring a variety of reactor configurations and failure modes in rapid order to provide insight into the most effective avenues of study for further research and development.

McConnell, Jono [ORNL] (ORCID:0000000238984741)↗
NASA NTRS2000

Electro-Mechanical Simulation of a Large Aperture MOEMS Fabry-Perot Tunable Filter

We are developing a micro-machined electrostatically actuated Fabry-Perot tunable filter with a large clear aperture for application in high through-put wide-field imaging spectroscopy and lidar systems. In the first phase of this effort, we are developing key components based on coupled electro-mechanical simulations. In particular, the movable etalon plate design leverages high coating stresses to yield a flat surface in drum-head tension over a large diameter (12.5 mm). In this approach, the cylindrical silicon movable plate is back etched, resulting in an optically coated membrane that is suspended from a thick silicon support ring. Understanding the interaction between the support ring, suspended membrane, and coating is critical to developing surfaces that are flat to within stringent etalon requirements. In this work, we present the simulations used to develop the movable plate, spring suspension system, and electrostatic actuation mechanism. We also present results from tests of fabricated proof of concept components.

Kuhn, Jonathan L.↗
DOE OSTI2020

Origin and effect of film sub-stoichiometry on ultraviolet, ns-laser damage resistance of hafnia single layers

Understanding the origin of laser damage-prone precursors in high index materials such as hafnia holds the key to the development of laser damage-resistant multilayer dielectric coated optics for high power and energy laser systems. In this study, we investigate the source of sub-stoichiometry, a potent laser damage precursor, in hafnia films produced by an ion beam sputtering (IBS) deposition method and the effect of such defects on the film performance upon ns ultraviolet (UV) laser (8 ns, 355 nm) exposure. Chemical analysis of data obtained via Rutherford backscattering spectroscopy (RBS) suggests that hafnia films deposited at two different planetary locations from the same deposition run exhibit anisotropic and location-dependent stoichiometries. While the oxygen-to-hafnium ratio is at the stoichiometric value of 2 for the hafnia film at the edge location, the ratio is significantly deviated and is 1.7 for that deposited at the planetary center. The sub-stoichiometric hafnia films display a much lower 1-on-1 damage onset at 1.6 ± 0.2 J/cm 2 compared to 2.3 ± 0.2 J/cm 2 in a stoichiometric film. The low damage performance films also have an over three times higher damage density at fluences above initiation. Coupled with Monte Carlo simulations, we reveal that sub-stoichiometry is primarily attributed to preferential removal of oxygen during film deposition by the bombardment of energetic reflected argon neutrals. The resulting oxygen deficiencies create the sub-bandgap states which facilitate the strong laser energy coupling and reduce the resistance to laser-induced damage in the hafnia single layer films.

36 MATERIALS SCIENCE↗
NASA NTRS2014

Development of the GEOS-5 Atmospheric General Circulation Model: Evolution from MERRA to MERRA2.

The Modern-Era Retrospective Analysis for Research and Applications-2 (MERRA2) version of the GEOS-5 (Goddard Earth Observing System Model - 5) Atmospheric General Circulation Model (AGCM) is currently in use in the NASA Global Modeling and Assimilation Office (GMAO) at a wide range of resolutions for a variety of applications. Details of the changes in parameterizations subsequent to the version in the original MERRA reanalysis are presented here. Results of a series of atmosphere-only sensitivity studies are shown to demonstrate changes in simulated climate associated with specific changes in physical parameterizations, and the impact of the newly implemented resolution-aware behavior on simulations at different resolutions is demonstrated. The GEOS-5 AGCM presented here is the model used as part of the GMAO's MERRA2 reanalysis, the global mesoscale "nature run", the real-time numerical weather prediction system, and for atmosphere-only, coupled ocean-atmosphere and coupled atmosphere-chemistry simulations. The seasonal mean climate of the MERRA2 version of the GEOS-5 AGCM represents a substantial improvement over the simulated climate of the MERRA version at all resolutions and for all applications. Fundamental improvements in simulated climate are associated with the increased re-evaporation of frozen precipitation and cloud condensate, resulting in a wetter atmosphere. Improvements in simulated climate are also shown to be attributable to changes in the background gravity wave drag, and to upgrades in the relationship between the ocean surface stress and the ocean roughness. The series of "resolution aware" parameters related to the moist physics were shown to result in improvements at higher resolutions, and result in AGCM simulations that exhibit seamless behavior across different resolutions and applications.

AGCM↗
NASA NTRS2017

Approach to Modeling Boundary Layer Ingestion Using a Fully Coupled Propulsion-RANS Model

Airframe-propulsion integration concepts that use boundary layer ingestion have the potential to reduce aircraft fuel burn. One concept that has been recently explored is NASA's Starc-ABL aircraft configuration, which offers the potential for 12% mission fuel burn reduction by using a turbo-electric propulsion system with an aft-mounted electrically driven boundary layer ingestion propulsor. This large potential for improved performance motivates a more detailed study of the boundary layer ingestion propulsor design, but to date, analyses of boundary layer ingestion have used uncoupled methods. These methods account for only aerodynamic effects on the propulsion system or propulsion system effects on the aerodynamics, but not both simultaneously. This work presents a new approach for building fully coupled propulsive-aerodynamic models of boundary layer ingestion propulsion systems. A 1D thermodynamic cycle analysis is coupled to a RANS simulation to model the Starc-ABL aft propulsor at a cruise condition and the effects variation in propulsor design on performance are examined. The results indicates that both propulsion and aerodynamic effects contribute equally toward the overall performance and that the fully coupled model yields substantially different results compared to uncoupled. The most significant finding is that boundary layer ingestion, while offering substantial fuel burn savings, introduces throttle dependent aerodynamics effects that need to be accounted for. This work represents a first step toward the multidisciplinary design optimization of boundary layer ingestion propulsion systems.

Boundary Layer Ingestion↗
DOE OSTI2021

TOUGH-RFPA: Coupled thermal-hydraulic-mechanical Rock Failure Process Analysis with application to deep geothermal wells

This paper presents a coupled thermal-hydraulic-mechanical (THM) model for simulating failure processes in geological media. The coupling between stress/strain and heat transfer describing how thermal expansion affects stress is based on the theory of thermo-elasticity. Additionally, the coupling between stress/strain and fluid flow describing how pore-pressure affects stress is governed by Biot's consolidation theory. Stress/strain-dependent porosity/permeability/capillary-pressure defines the influence of stress on fluid flow and thermal fields. The THM model is implemented in the solver module that links the multiphase, multicomponent fluid flow simulator TOUGH2 with the geomechanical simulator RFPA (Rock Failure Process Analysis), which is based on the concept that heterogeneity leads to non-linearity and progressive failure behavior. Capability of TOUGH-RFPA simulator was verified by two benchmark problems related to hydraulic-mechanical and thermal-mechanical response in a hollow cylinder. Then the applicability of TOUGH-RFPA was demonstrated for modeling cooling-induced damage around a very deep geothermal well with mesoscopic heterogeneous properties, which showed complex damage evolution and fracturing during well cooling and fluid pressurization.

42 ENGINEERING↗
NASA NTRSDate not supplied

A Framework for Optimization-Based ISRU Tool Design Using Discrete Element Modeling

Novel robotic excavation technologies are needed to perform in-situ resource utilization (ISRU) tasks at levels required to sustain a long-term presence on the lunar surface. Developing and testing multiple iterations of functional hardware is time and cost prohibitive, thus slowing down the pace of progress and delaying humanity’s settlement of the Moon. High-fidelity, physics-based simulation can reduce the time and effort required to develop and deploy robotic systems [1]. We have adopted this approach to create high-fidelity models of robotic test hardware to enable rapid virtual design and optimization of excavation technologies [2]. Such models can leverage modern computational tools like Discrete Element Method (DEM) simulations that can be coupled with automated design approaches like topology optimization to reduce the amount of prototyping and physical testing needed to realize useful tools.

ISRU↗
DOE OSTI2021

Inference of Rock Flow and Mechanical Properties from Injection-Induced Microseismic Events During Geologic CO 2 Storage

Monitoring microseismic activities during CO 2 injection into geologic formations is important for ensuring the safety of the storage operations. The resulting data provide insight into the response of the storage formation to CO 2 injection and can be used to infer the underlying rock flow and mechanical properties. In this paper, assimilation of microseismic data is performed for dynamic characterization of the storage formation by using a stochastic simulation model to forecast the microseismic response of a geologic formation during CO 2 injection. Two modeling approaches are adopted to predict the space-time distribution of the injection-induced microseismicity. The first model is based on pore pressure relaxation assumption, while the second model uses coupled flow and geomechanics simulation to establish the complex physical relation between the storage formation properties and the corresponding microseismic responses during CO 2 injection. The stochastic predictive models in each case are used in ensemble data assimilation frameworks to estimate rock properties from the observed microseismic data. Two data assimilation methods are considered: (i) a new ensemble-based stochastic point process filter (EnPPF) that can directly integrate discrete microseismic events, and (ii) a variant of ensemble smoother, known as the ensemble smoother with multiple data assimilation (ES-MDA), which requires continuous representation of microseismic events for assimilation. The two methods are successfully applied to a geologically realistic model of the Farnsworth Field in Texas, with complex geologic flow units and interacting fault systems.

42 ENGINEERING↗
DOE OSTI2025

Aeroelastic Modelling of Large Wind Turbines: Towards a Unified OpenFAST-SEAHOWL Approach

In recent years, the scale of wind turbines has significantly increased to maximize energy capture for a given site (particularly offshore), presenting new challenges in terms of structural design and dynamics. As towers grow taller and blades grow longer, flexion and torsion of the latter have a non-negligible impact on the behavior and performance of the turbine in terms of overall loads, power production, and control. When representing large-scale wind turbines numerically to capture these important effects, particular attention must therefore be given to the level of fidelity for representing each structural component, as well as the coupling scheme used between them to keep simulations accurate, stable, and efficient. To address this issue, we combine here the two following tools: (1) OpenFAST, the reference whole-turbine simulation tool from NREL with standalone modules covering each physics and the choice between loose coupling and a new tight coupling scheme for structural dynamics, and (2) SEAHOWL, the whole-turbine simulation tool from TotalEnergies with monolithic coupling of structural dynamics through Project Chrono and partitioned coupling for multiphysics interactions.

17 WIND ENERGY↗
DOE OSTI2024

Nonlinear modeling of ELM mitigation with RMP on HL-2A

Abstract Nonlinear modeling of mitigation of the edge localized mode (ELM) with resonant magnetic perturbation (RMP) is performed for the HL-2A tokamak, utilizing the three-dimensional (3D) magnetohydrodynamic code JOREK. Based on the 3D equilibrium established after application of the n = 1 ( n is the toroidal mode number) RMP at 4.9 kAt coil current with odd parity, ELM mitigation is successfully simulated consistent with the experimental result. Nonlinear simulations show strong mode coupling among toroidal Fourier harmonics, allowing redistribution of the magnetic energy such that the most unstable toroidal mode saturates at a lower level. This magnetic energy cascade offers an explanation of the RMP-induced ELM mitigation achieved in HL-2A. Detailed examination of the simulation results shows persistent resonant field screening even during the ELM mitigation phase. Finite plasma resistivity however does enable partial penetration of the resonant field thus modifying the edge magnetic topology and characteristics of the edge transport. Plasma radial profiles undergo pronounced changes around the pedestal region, when the magnetic energy of the most unstable toroidal mode reaches the maximum value. Systematic scans of the applied RMP coil current with the JOREK simulations find a threshold value of around 4.5 kAt required for achieving the ELM mitigation on HL-2A.

Physics↗
DOE OSTI2020

Stability Analysis of Interface Conditions for Ocean-Atmosphere Coupling

In this paper, we analyze the stability of different coupling strategies for multidomain PDEs that arise in general circulation models used in climate simulations. We focus on fully coupled ocean–atmosphere models that are needed to represent and understand the complicated interactions of these two systems, becoming increasingly important in climate change assessment in recent years. Numerical stability issues typically arise because of different time-stepping strategies applied to the coupled PDE system. In particular, the contributing factors include using large time steps, lack of accurate interface flux, and single-iteration coupling. We investigate the stability of the coupled ocean–atmosphere models for various interface conditions such as the Dirichlet–Neumann condition and the bulk interface condition, which is unique to climate modeling. By analyzing a simplified model, we demonstrate here how the parameterization of the bulk condition and other numerical and physical parameters affect the coupling stability and establish stability conditions for different coupling strategies.

97 MATHEMATICS AND COMPUTING↗