Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Aqueous solution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

NH 4 OH Looping with Membrane CO 2 Absorber and Distributed Stripper for Enhanced Algae Growth

The University of Kentucky Center for Applied Energy (UK CAER) has devised a unique, integrated CO2 capture and utilization technology. CO2 from coal-fired power generation flue gas is first captured at half the operating cost of a typical aqueous CO2 capture system (CCS), distributed in an aqueous stream and then fixed by algae in bioreactors where the algae production is increased by 50% over that with a typical intermittent nutrient feeding system. Lower CCS operating cost is achieved by eliminating the flue gas pretreatment step for cooling and SO2 removal, eliminating steam extraction from the power generation steam cycle for solvent regeneration, and eliminating CO2 compression. Higher algae production is achieved by continuous, just-in-time nutrient feed to the bioreactors directly from a distributed solvent regenerator, which maintains the bioreactor pH for optimum growth. The process starts with a uniquely configured membrane absorber, where the flue gas is indirectly contacted with an ammonium hydroxide (NH4OH) solvent. Dissolved NH3 is attractive for both CO2 capture and as an algae nutrient. For CO2 capture it is inexpensive, has a low regeneration energy, is thermally- and oxidatively-stable and has a viscosity near that of water, which makes is easy to transport. Numerous studies have shown that the scrubbing capacity of NH3 is approximately 0.9-1.2 kg of CO2/kg of NH3, with a CO2 removal efficiency of ~99% and half the solvent regeneration energy than that of 30 wt% MEA[1, 2, 3]. NH3 is attractive as an algae nutrient due to its low cost. The rich NH4OH solvent is pumped to a set of distributed regenerators which are co-located with the algae bioreactors. Solvent pumping, transport and distribution reduces the balance of plant (BOP) cost compared to a typical aqueous CCS related to the flue gas duct and boost fan required to transport the flue gas. The energy required for the distributed solvent regeneration is supplied by solar-thermal panels eliminating the need for steam extraction from the power generation steam cycle. After solvent regeneration, the product stream contains both the CO2 captured from the flue gas and volatized NH3 from the solvent. This product stream is fed directly to the bioreactors, eliminating the need for compression of the CO2 stream. The relative amounts of CO2 and NH3 in the product stream are adjusted and controlled by a controlling the regeneration conditions (pressure and temperature). The continuous feed of the right ratio of nutrients overcomes the typical inhibition of algae growth resulting from frequent pH swings in the bioreactor due to unbalanced (intermittent) feeding systems for CO2 and N. Also, because the regenerators will operate at pressure and be located in close proximity to the bioreactors, there is no worry about pressure drop when sparging the gas into the algae. Sparging produces small bubbles which is beneficial for mass transfer efficiency. One known challenge when using an NH4OH solvent is high NH3 emission. Hydrophobic membranes are used for CO2 capture using an aqueous NH3 solution[4, 5] without the direct contact between flue gas and aqueous solution. Additionally, UK CAER CO2 capture and utilization process manages NH3 slip in three extra measures. First, NH3 slip is minimized by working with minimal species partial pressure, which is proportional to the concentration in the liquid. Hence, lowering the capture solvent concentration will lower the NH3 partial pressure. Second, UK CAER’s previous work has demonstrated that the addition of Zn2+ into NH3 solutions to chelate the NH3 can reduce NH3 volatility. Third, the configuration of the membrane CO2 absorber utilizes condensed water from the flue gas to continually wash the gas-side of the membrane to reduce fouling and recapture NH3 slip. Additional details about the UK CAER unique, integrated CO2 capture and utilization technology will be presented along with technology development plans. Diao, N., Q. Li, and Z. Fang. 2004. Heat transfer in ground heat exchangers with groundwater advection. International Journal of Thermal Sciences. 43: 1203-1211, He, Q., M. Chen, L. Meng, K. Liu, and W. Pan. 2004. Study on Carbon Dioxide Removal from Flue Gas by Absorption of Aqueous Ammonia. Western Kentucky University. Yeh, A.C., and H. Bai. 1999. Comparison of ammonia and monoethanolamine solvents to reduce CO2 greenhouse gas emissions. The Science of the Total Environment. 228: 121-133, Villeneuve, K., D. Roizard, J.C. Remigy, M. Iacono, and S. Rode. 2018. CO2 capture by aqueous ammonia with hollow fiber membrane contactors: Gas phase reactions and performance stability. Separation and Purification Technology, 199: 189-197, Toro Molina, C., and C. Bouallou. 2016. Carbon dioxide absorption by ammonia intensified with membrane contactors. Clean Techn Environ Policy 18, 2133–2146 (2016)

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2023

Aqueous buffer solution-induced crystallization competes with enzymatic depolymerization of pre-treated post-consumer poly (ethylene terephthalate) waste

In this paper, the complex relationship between kinetics and substrate morphology during enzymatic depolymerization of melt processed poly(ethylene terephthalate) (PET) is explored and the effects of competing transformations are analyzed. Extruded PET substrates from post-consumer recycled PET (RPET) bottles flakes subjected to enzymatic depolymerization are examined to reveal increases in crystallinity from ~10% post-extrusion to >30% after 3 days of depolymerization as well as increases in glass transition temperature (T g ) from ~66°C to > 80°C. Further investigation into this behavior shows that post-extrusion RPET substrates do not exhibit changes in crystallinity when subjected to dry annealing at 65°C in an oven over 7 days, but they do experience annealing in depolymerization buffer solution with no enzymes at 65°C within 3 days. This difference may be attributed to plasticization of PET in the presence of water, also known as solvent induced crystallization. The impact of this plasticized annealing behavior is demonstrated by subjecting RPET substrates to increasing enzyme-to-substrate loads. As enzyme load increases, overall conversion of substrates increases despite crystallinity also increasing to similar levels regardless of the initial enzyme loading. The competition between depolymerization and crystallization suggests that the rate at which PET substrates are depolymerized at the operational temperature is integral to achieving high conversion to monomeric product. This, in turn, also suggests that savings from lowered enzyme loadings may be more detrimental than helpful in pursuing the most cost-effective recycling systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Synthesis of Single Crystal Li 2 NpO 4 and Li 4 NpO 5 from Aqueous Lithium Hydroxide Solutions under Mild Hydrothermal Conditions

The ternary oxides, Li 2 NpO 4 and Li 4 NpO 5 , were synthesized under mild hydrothermal conditions using concentrated LiOH solutions containing NpO 2 (NO 3 )( 2 ). The reactions resulted in the formation of single crystals of both compounds, enabling the determination of their single crystal structures for the first time. Further, exploration of the synthetic phase space demonstrates that the resulting neptunate phases are dependent on the concentration of LiOH, transitioning from Li 2 NpO 4 , containing a typical octahedral neptunyl geometry with two shorter Np≡O bonds, at lower LiOH concentrations to Li 4 NpO 5 with two long and four short Np-O bonds under saturated solution conditions. Reactions exploring the same synthetic conditions are also reported for uranyl(VI) for comparison. Raman spectra of the compounds were collected and analyzed to evaluate the Np-O bonding in these compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1991

Experimental study of directional solidification of aqueous ammonium chloride solution

Directional solidification experiments have been carried out using the analog casting system of NH4Cl-H2O solution by cooling it from below with a constant-temperature surface ranging from -31.5 C to +11.9 C. The NH4Cl concentration was 26 percent in all solutions, with a liquidus temperature of 15 C. It was found that finger convection occurred in the fluid region just above the mushy layer in all experiments. Plume convection with associated chimneys in the mush occurred in experiments with bottom temperatures as high as +11.0 C. However, when the bottom temperature was raised to +11.9 C, no plume convection was observed, although finger convection continued as usual. A method has been devised to determine the porosity of the mush by computed tomography. Using the mean value of the porosity across the mush layer and the permeability calculated by the Kozeny-Carman relationship, the critical solute Rayleigh number across the mush layer for onset of plume convection was estimated to be between 200 and 250.

Chen, C. F.↗
NASA NTRS1945

Heat-transfer tests of aqueous ethylene glycol solutions in an electrically heated tube

As part of an investigation of the cooling characteristics of liquid-cooled engines, tests were conducted with an electrically heated single-tube heat exchanger to determine the heat-transfer characteristics of an-e-2 ethylene glycol and other ethylene glycol-water mixtures. Similar tests were conducted with water and commercial butanol (n-butyl alcohol) for check purposes. The results of tests conducted at an approximately constant liquid-flow rate of 0.67 pound per second (Reynolds number, 14,500 to 112,500) indicate that at an average liquid temperature 200 degrees f, the heat-transfer coefficients obtained using water, nominal (by volume) 30 percent-70 percent and 70 percent-30 percent glycol-water mixtures are approximately 3.8, 2.8, and 1.4 times higher, respectively, than the heat-transfer coefficients obtained using an-e-2 ethylene glycol.

Bernardo, Everett↗
DOE OSTI2024

Effective direct steam regeneration of bis-iminoguanidine solid sorbent used for carbon dioxide capture

A cost-effective, energy-efficient sorbent regeneration process for phase-changing guanidines used for CO 2 capture was developed based on direct-steam stripping. This approach enhances the regeneration rate, simplifies the overall CO 2 capture process, and reduces the energy cost compared to conventional conductive thermal regeneration. A direct-steam sorbent regeneration reactor was developed, demonstrating that aqueous bis(iminoguanidines) (BIG) sorbents, e.g., methylglyoxal-bis(iminoguanidine) (MGBIG) and glyoxal-bis(iminoguanidine) (GBIG), could be efficiently regenerated with up to ~ 99 % CO 2 recovery through direct-steam stripping. Using low-temperature steam at 100 °C, a 4.5 times faster regeneration rate for GBIG carbonate sorbent (e.g., 30 min for 10 g) was demonstrated compared to conductive-heating (e.g., 135 min for 10 g) at 130 °C. Additionally, fully regenerated MGBIG converts into an aqueous MGBIG solution when the steam condenses onto the sorbent surface. Condensed steam with the guanidine can be easily recycled as an aqueous solution into the gas–liquid contactor to achieve a continuous-flow CO 2 -capture process. Molecular dynamics simulation was employed to provide a better understanding of the process. Higher heat transfer rates from steam to guanidine carbonate, compared to air heating, were attributed to the vibration resonance of water molecules within MGBIG with that of vapor molecules and the effective transfer of kinetic energy from vapor to solid. Technoeconomic analysis demonstrated that direct-steam stripping significantly decreases the CO 2 capture cost by 50 % compared to traditional conductive heating methods. Further, enhanced mass transfer facilitated by low-temperature steam and subsequent condensation effectively heats up the H 2 O-containing BIG-carbonate crystals, facilitating the desorption of CO 2 from the solid crystals, thereby leading to fast, effective, and energy-efficient sorbent regeneration.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A General Binary Isotherm Model for Amines Interacting with CO 2 and H 2 O

CO 2 capture by primary or secondary amines has been of great research interests for a century because of its industrial importance. Interest has grown even more, because of the need to eliminate the CO 2 emissions that drive global warming. Experimental evidence shows that CO 2 sorption in primary or secondary amines is accompanied by co-absorption of H 2 O. A quantitative analysis of such CO 2 -H 2 O co-absorption behavior is important for practical process design and theoretical understanding. Even though there is almost an experimental consensus that water enhances CO 2 uptake capacity, an analytic model to explain this phenomenon is not well established. Instead, some empirical models such as the Toth model are used to describe the isotherm without accounting for the presence of water. Recently, we have demonstrated that the isotherm equation of CO 2 sorption into strong-base anion exchange materials with quaternary ammonium can be derived from that of strong-base aqueous alkaline solutions by correcting for the drastic change in water activity and by including an appropriate parameterization of the water activity terms. In this paper, we generalize this model from quaternary ammonium to primary, secondary and tertiary amines either in solutions or as functional groups in polymer resins. For primary, secondary and tertiary amines, the isotherm equation can be derived by extending that of a weak-base aqueous alkaline solution such as aqueous ammonia. The model has been validated using experimental data of aqueous ammonia in literature. Furthermore, this general model even includes quaternary ammonium as a special limit. Hence, this general model offers a platform that can treat the isotherms of solid amines, aqueous amines and aqueous alkaline solutions in a unified way.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Solar-thermal membrane for dewatering aqueous organic-acid solutions

A thermally conductive porous membrane has been developed to directly absorb solar energy and conduct heat that can effectively evaporate liquid water at the interface between the membrane and the bulk feed solution. Here, black, porous, thermally conductive graphite foam support is employed as an effective photothermal-energy absorber and heat conductor that heats up an aqueous feed solution to produce vapor. Graphite nanoparticle-slurry coating is applied onto the foam surface to reduce the pore size and generate a microporous membrane. Then, application of a dense graphene oxide membrane coating as an active separation layer on the microporous nanoparticle surface of internal foam channels allows vapor permeation of volatile molecules. Acetic acid/water solution was studied as a model feed system to experimentally demonstrate effective separation. This model vapor permeation system demonstrates excellent acetic acid separation, with a separation factor of 8.3, under simulated 0.7 sun irradiation. The membrane hydrophobicity and nanostructure, including pore size and surface chemistry, played a significant role in enabling high permselectivity of water vapor over acetic acid molecules, as well as liquid solution. Pore size reduction from open pores to a nonporous dense layer in the membrane enables effective separation of water vapor from the organic vapor, while it reduces the permeation flux. Also, the hydrophilicity of the membrane surface shows ~3 times higher permeation flux with higher permselectivity, compared with the hydrophobic membrane surface. This work introduces a process of directly using renewable energy instead of conventional heating to drive selective separation of water from organic acids.

14 SOLAR ENERGY↗
NASA NTRS1976

Diffusion in mixed solvents. III - The heat of mixing parameter and the Soret coefficient

New evidence is presented that for aqueous glycerol solutions, the Soret coefficient of glycerol, sigma sub 1 = D sub 1 T/D sub 1 (where D sub 1 T and D sub 1 are the thermal and self-diffusion coefficients, respectively, of glycerol in aqueous solutions), is an integral part of the heat of mixing parameter. Expressions are presented indicating the importance of the Soret coefficients to correlations for diffusion processes in glycerol water solvents.

Carapellucci, P. A.↗
DOE OSTI2022

Tracking structural solvent reorganization and recombination dynamics following e – photoabstraction from aqueous I – with femtosecond x-ray spectroscopy and scattering

Here we present a sub-picosecond resolved investigation of the structural solvent reorganization and geminate recombination dynamics following 400 nm two-photon excitation and photodetachment of a valence p electron from the aqueous atomic solute, I–(aq). The measurements utilized time-resolved X-ray Absorption Near Edge Structure (TR-XANES) spectroscopy and X-ray Solution Scattering (TR-XSS) at the Linac Coherent Light Source x-ray free electron laser in a laser pump/x-ray probe experiment. The XANES measurements around the L 1 -edge of the generated nascent iodine atoms (I 0 ) yield an average electron ejection distance from the iodine parent of 7.4 ± 1.5 Å with an excitation yield of about 1/3 of the 0.1M NaI aqueous solution. The kinetic traces of the XANES measurement are in agreement with a purely diffusion-driven geminate iodine–electron recombination model without the need for a long-lived (I 0 :e–) contact pair. Nonequilibrium classical molecular dynamics simulations indicate a delayed response of the caging H 2 O solvent shell and this is supported by the structural analysis of the XSS data: We identify a two-step process exhibiting a 0.1 ps delayed solvent shell reorganization time within the tight H-bond network and a 0.3 ps time constant for the mean iodine–oxygen distance changes. The results indicate that most of the reorganization can be explained classically by a transition from a hydrophilic cavity with a well-ordered first solvation shell (hydrogens pointing toward I–) to an expanded cavity around I 0 with a more random orientation of the H 2 O molecules in a broadened first solvation shell.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Co-ion specific effect on sodium halides sorption and transport in a cross-linked poly(p-styrene sulfonate-co-divinylbenzene) for membrane applications

Here, sodium halide sorption and transport in a cation exchange membrane based on cross-linked poly(p-styrene sulfonate-co-divinylbenzene) (CR61) were investigated experimentally and theoretically. At fixed co-ion valence, sodium halide partitioning between aqueous electrolyte solutions and ion exchange polymers is only minimally sensitive to co-ion chemical identity. NaCl, NaF and NaI exhibit similar solubility coefficients in CR61, which agrees reasonably well with predictions of the Donnan-Manning model, especially at high external salt concentrations. Ion activity coefficients in the membrane were evaluated and ion sorption thermodynamics were investigated. Ion diffusion coefficients in CR61 were predicted using a recently developed framework based on the Manning diffusion model, which accounts for electrostatic effects on ion diffusion, and the Mackie-Meares model, which accounts for tortuosity/area effects on ion diffusion in swollen polymers. Model predictions agree reasonably well with the experimental data, especially at high external salt concentrations. The observed decrease in salt diffusion coefficients in CR61 relative to values in aqueous solutions is due primarily to tortuosity/area effects. Salt diffusion coefficients correlate with co-ion hydrated radius and membrane water content. Finally, salt permeability coefficients predicted using the solution-diffusion model exhibit good agreement with experimental data, especially at external salt concentration greater than 0.1 mol/L.

42 ENGINEERING↗
DOE OSTI2023

Observationally Constrained Modeling of the Reactive Uptake of Isoprene-Derived Epoxydiols under Elevated Relative Humidity and Varying Acidity of Seed Aerosol Conditions

Isoprene is the non-methane volatile organic compound (VOC) emitted in largest amounts to the atmosphere, and it is a significant source of secondary organic aerosol (SOA) mass. The uptake of isoprene oxidation products followed by multiphase chemistry in fine particles is the key pathway to form isoprene epoxydiol-derived SOA (IEPOX-SOA). However, many parameters that relate to diffusion and reaction of IEPOX in the particle phase remain uncertain, since reaction kinetics previously measured in bulk aqueous phase solutions might be different from atmospheric aerosols. Here, we use simultaneous environmental chamber measurements of multiple parameters governing IEPOX-SOA formation at timescales of ~hours: particle size distribution, composition, and volatility of IEPOX-SOA to constrain the key parameters governing IE-POX-SOA formation under humid (i.e., 50% relative humidity, RH) and varying seed aerosol acidity conditions. Reducing the 2-methyltetrol (tetrol) reaction rate constants by a factor of 4 brings the model predictions in agreement with the IEPOX-SOA measurements with acidified ammonium bisulfate seed aerosols. For less acidic ammonium sulfate aerosols both the organo-sulfate (OS) and tetrol reaction rate constants need to be reduced to bring model predictions closer to chamber observations. Using the measured non-volatile content of IEPOX-SOA we constrain the oligomerization timescale of 2-methyltetrols. We find that the oligomerization timescale is 4 hours with acidified seed aerosols, but a much longer time scale of 24 hours is needed for non-acidified seed aerosols, indicating that the aerosol acidity greatly affects the oligomerization rate of tetrols. Here we show that the actual kinetics of IEPOX-SOA formation rate on aerosol seeds consisting of both ammonium bisulfate and ammonium sulfate are a factor of 4~5 slower under 50-60% RH conditions compared to their application in previous models, which were based on bulk aqueous solution measurements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Direct Air Capture of CO 2 Using Solvents

Large-scale deployment of negative emissions technologies (NETs) that permanently remove CO 2 from the atmosphere is now considered essential for limiting the global temperature increase to less than 2°C by the end of this century. One promising NET is direct air capture (DAC), a technology that employs engineered chemical processes to remove atmospheric carbon dioxide, potentially at the scale of billions of metric tons per year. This review highlights one of the two main approaches to DAC based on aqueous solvents. The discussion focuses on different aspects of DAC with solvents, starting with the fundamental chemistry that includes the chemical species and reactions involved and the thermodynamics and kinetics of CO 2 binding and release. Chemical engineering aspects are also discussed, including air–liquid contactor design, process development, and technoeconomic assessments to estimate the cost of the DAC technologies. Various solvents employed in DAC are reviewed, from aqueous alkaline solutions (NaOH, KOH) to aqueous amines, amino acids, and peptides, along with different solvent regeneration methods, from the traditional thermal swinging to the more exploratory carbonate crystallization with guanidines or electrochemical methods.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1970

Oxygen-hydrogen fuel cell with an iodine-iodide cathode - A concept

Fuel cell uses a porous cathode through which is fed a solution of iodine in aqueous iodide solution, the anode is a hydrogen electrode. No activation polarization appears on the cathode because of the high exchange-current density of the iodine-iodide electrode.

Javet, P.↗
DOE OSTI2020

All-vanadium sulfate acid redox flow battery system

All-vanadium sulfate redox flow battery systems have a catholyte and an anolyte comprising an aqueous supporting solution including chloride ions and phosphate ions. The aqueous supporting solution stabilizes and increases the solubility of vanadium species in the electrolyte, allowing an increased vanadium concentration over a desired operating temperature range. According to one example, the chloride ions are provided by MgCl2, and the phosphate ions are provided by (NH4)2HPO4.

25 ENERGY STORAGE↗
DOE OSTI2022

All-vanadium sulfate acid redox flow battery system

All-vanadium sulfate redox flow battery systems have a catholyte and an anolyte comprising an aqueous supporting solution including chloride ions and phosphate ions. The aqueous supporting solution stabilizes and increases the solubility of vanadium species in the electrolyte, allowing an increased vanadium concentration over a desired operating temperature range. According to one example, the chloride ions are provided by MgCl 2 , and the phosphate ions are provided by (NH 4 ) 2 HPO 4 .

Nie, Zimin↗