Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Airframes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,117 records · Page 62

Friction and wear behavior of aluminum and composite I-beam stiffened airplane skins

Friction and wear behavior was determined for I-beam stiffened skins constructed of aluminum, graphite-epoxy composite, and glass hybrid composite under abrasive loading conditions typical of those occurring on the underside of a transport airplane during an emergency belly landing. A test apparatus was developed to abrade the test specimens on actual runway surface under a range of pressures (2-5 psi) and velocities (16-50 mph). These parameters were chosen to fall within the range of conditions typical of an airframe sliding on a runway surface. The effects of the test variables on the wear rate and the coefficient of friction are discussed and comparisons are made between the composite materials and aluminum. In addition, the test apparatus was equipped to monitor the temperature variations on the backside of the skins during abrasion and these results are presented.

Jackson, K. E.↗

Active control landing gear for ground load alleviation

Results of analytical and experimental investigations of a series-hydraulic active control landing gear show that such a gear is feasible when using existing hardware and is very effective in reducing loads, relative to those generated by a conventional (passive year) gear, transmitted to the airframe during ground operations. Analytical results obtained from an active gear, flexible aircraft, take-off and landing analysis are in good agreement with experimental data and indicate that the analysis is a valid tool for study and initial design of series-hydraulic active control landing gears. An analytical study of a series-hydraulic active control main landing gear on an operational supersonic airplane shows that the active gear has the potential for improving the dynamic response of the aircraft and significantly reducing structural fatigue damage during ground operations.

Mcgehee, J. R.↗

Recent developments in the dynamics of advanced rotor systems

The problems that have been encountered in the dynamics of advanced rotor systems are described. The methods for analyzing these problems are discussed, as are past solutions of the problems. To begin, the basic dynamic problems of rotors are discussed: aeroelastic stability, rotor and airframe loads, and aircraft vibration. Next, advanced topics that are the subject of current research are described: vibration control, dynamic inflow, finite element analyses, and composite materials. Finally, the dynamics of various rotorcraft configurations are considered: hingeless rotors, bearingless rotors, rotors with circulation control, coupled rotor/engine dynamics, articulated rotors, and tilting proprotor aircraft.

Johnson, W.↗

Performance improvements of a highly integrated digital electronic control system for an F-15 airplane

The NASA highly integrated digital electronic control (HIDEC) program is structured to conduct flight research into the benefits of integrating an aircraft flight control system with the engine control system. A brief description of the HIDEC system installed on an F-15 aircraft is provided. The adaptive engine control system (ADECS) mode is described in detail, together with simulation results and analyses that show the significant excess thrust improvements achievable with the ADECS mode. It was found that this increased thrust capability is accompanied by reduced fan stall margin and can be realized during flight conditions where engine face distortion is low. The results of analyses and simulations also show that engine thrust response is improved and that fuel consumption can be reduced. Although the performance benefits that accrue because of airframe and engine control integration are being demonstrated on an F-15 aircraft, the principles are applicable to advanced aircraft such as the advanced tactical fighter and advanced tactical aircraft.

Putnam, T. W.↗

Joined-wing research airplane feasibility study

The joined wing is a new type of aircraft configuration which employs tandem wings arranged to form diamond shapes in plan view and front view. Wind-tunnel tests and finite-element structural analyses have shown that the joined wing provides the following advantages over a comparable wing-plus-tail system; lighter weight and higher stiffness, higher span-efficiency factor, higher trimmed maximum lift coefficient, lower wave drag, plus built-in direct lift and direct sideforce control capability. To verify these advantages at full scale a manned research airplane is required. A study has therefore been performed of the feasibility of constructing such an airplane, using the fuselage and engines of the existing NAA AD-1 oblique-wing airplane. Cost and schedule constraints favored converting the AD-1 rather than constructing a totally new airframe. By removing the outboard wing panels the configuration can simulate wings joined at 60, 80, or 100 percent of span. For maximum versatility the aircraft has alternative control surfaces (such as ailerons and elevators on the front and/or rear wings), and a removeable canard to explore canard/joined-wing interactions at high-lift conditions. Design, performance, and flying qualities are discussed.

Wolkovitch, J.↗

Higher harmonic control for rotary wing aircraft

Higher Harmonic Control reduces helicopter airframe vibration through the exercise of rotor blade pitch control at frequencies that are higher harmonics of rotor rotation. Analysis wind tunnel tests and flight tests of this technology with an OH-6A helicopter have led to vibration reduction levels of the order of more than 80 percent. Blade feathering capability at rotor speed harmonics other than the first also promises the improvement of such rotor characteristics as acoustics, aerodynamic efficiency and ground resonance.

Gupta, B. P.↗

Predicted performance benefits of an adaptive digital engine control system on an F-15 airplane

The highly integrated digital electronic control (HIDEC) program will demonstrate and evaluate the improvements in performance and mission effectiveness that result from integrating engine-airframe control systems. Currently this is accomplished on the NASA Ames Research Center's F-15 airplane. The two control modes used to implement the systems are an integrated flightpath management mode and an integrated adaptive engine control system (ADECS) mode. The ADECS mode is a highly integrated mode in which the airplane flight conditions, the resulting inlet distortion, and the available engine stall margin are continually computed. The excess stall margin is traded for thrust. The predicted increase in engine performance due to the ADECS mode is presented in this report.

Burcham, F. W., Jr.↗

Orbit on demand - Structural analysis finds vertical launchers weigh less

Structural considerations arising from favored design concepts for the next generation on-demand launch vehicles are explored. The two emerging concepts are a two stage fully reusable vertical take-off vehicle (V-2) and a horizontal take-off, two stage subsonic boost launch vehicle (H-2-Sub). Both designs have an 1100 n. mi. cross-range capability, with the V-2 orbiter having small wings with winglets for hypersonic trim and the H-2-Sub requiring larger, swept wings. The rockets would be cryogenic, while airbreathing initial boosters would be either turbofans, turbojets and/or ramjets. Dynamic loading is lower in the launch of a V-2. The TPS is a critical factor due to thinner leading edges than on the Shuttle and may require heat-pipe cooling. Airframe structures made of metal matrix composites have passed finite element simulations of projected loads and can now undergo proof-of-concept tests, although whisker-reinforced materials may be superior once long-whisker technology is developed.

Taylor, A. H.↗

Icing flight research - Aerodynamic effects of ice and ice shape documentation with stereo photography

Aircraft icing flight research was performed in natural icing conditions. A data base consisting of icing cloud measurements, ice shapes, and aerodynamic measurements is being developed. During research icing encounters the icing cloud was continuously measured. After the encounter, the ice accretion shapes on the wing were documented with a stereo camera system. The increase in wing section drag was measured with a wake survey probe. The overall aircraft performance loss in terms of lift and drag coefficient changes were obtained by steady level speed/power measurements. Selective deicing of the airframe components was performed to determine their contributions to the total drag increase. Engine out capability in terms of power available was analyzed for the iced aircraft. It was shown that the stereo photography system can be used to document ice shapes in flight and that the wake survey probe can measure increases in wing section drag caused by ice. On one flight, the wing section drag coefficient (c sub d) increased approximately 120 percent over the uniced baseline at an aircraft angle of attack of 6 deg. On another flight, the aircraft drag coefficient (c sub d) increased by 75 percent over the uniced baseline at an aircraft lift coefficient (c sub d) of 0.5.

Mikkelsen, K. L.↗

TF34 convertible engine control system design

The characteristics of the TF34 convertible engine, capable of producing shaft power, thrust, or a combination of both, is investigated with respect to the control system design, development, bench testing, and the anticipated transient response during engine testing at NASA. The modifications to the prototype standard TF34-GE-400 turbofan, made primarily in the fan section, consist of the variable inlet guide vanes and variable exit guide vanes. The control system was designed using classical frequency domain techniques and was based on the anticipated convertible/VTOL airframe requirements. The engine has been run in the fan mode and in the shaft mode, exhibiting a response of 0.14 second to a 5-percent thrust change.

Gilmore, D. R., Jr.↗

Nonlinear applications of slender-body theory to missile aerodynamics

An evaluation is made of six diverse examples of nonlinear treatments of slender body theory for the prediction of missile aerodynamic behavior. The cases in question are the application of area rule to store carriage design in the drag rise region, the estimation of destabilizing pitching moments associated with transonic projectiles, the pressure loadings on elliptical missile airframes, nonlinear control characteristics, roll control effectiveness in canard missile configurations, and novel approaches for vortex flow modeling.

Hemsch, M. J.↗

Applications of numerical optimization methods to helicopter design problems - A survey

A survey of applications of mathematical programming methods is used to improve the design of helicopters and their components. Applications of multivariable search techniques in the finite dimensional space are considered. Five categories of helicopter design problems are considered: (1) conceptual and preliminary design, (2) rotor-system design, (3) airframe structures design, (4) control system design, and (5) flight trajectory planning. Key technical progress in numerical optimization methods relevant to rotorcraft applications are summarized.

Miura, H.↗

Aerodynamics and Acoustics of Propellers

A state of the art review of the aerodynamic design and testing of modern propellers, acoustic and vibration environmental problems and their solutions, and considerations in the integration of the propeller(s) and airframe is presented. Propellers have recently become a focus of attention after having been neglected for many years. The efficient use of propellers as a propulsion medium up to Mach 0.6 was realized at the expense of high noise and vibration. Since the mid-1970s there have been many developments, including the propfan, with an aerodynamic efficiency of 80% at Mach 0.8 now seriously challenges the fanjet. The advent of the supercritical airfoil is another significant development beginning to influence propeller design.

Design↗

Impact dynamics instrumentation

One of the tasks specified in the NASA Langley controlled impact demonstration (CID) work package was to furnish dynamic instrumentation sensors. The types of instrumentation sensors required were accelerometers for aircraft structural loads measurements, seat belt load cells to measure anthropomorphic dummy responses to the aircraft impact, and strain gage bending bridges to measure the aircraft fuselage and wing bending during impact. The objective in the selection of dynamic instrumentation for the CID was to provide 352 of the highest quality transducers and remain within budget allocation. The transducers that were selected for the CID evaluation process were each subjected to rigorous laboratory acceptance tests and to aircraft fuselage section drop tests at the LaRC Impact Dynamics Research Facility. Data compiled from this series of tests showed the selected transducers to be best suited for the CID mission requirement. The transducers installation technique on the airframe proved successful. The transducer quality assurance was guaranteed through rigorous acceptance testing. Data acquired was 97.0%.

Mccormck, R. F.↗

Test and evaluation of the HIDEC engine uptrim algorithm

The highly integrated digital electronic control (HIDEC) program will demonstrate and evaluate the improvements in performance and mission effectiveness that result from integrated engine-airframe control systems. Performance improvements will result from an adaptive engine stall margin mode, a highly integrated mode that uses the airplane flight conditions and the resulting inlet distortion to continuously compute engine stall margin. When there is excessive stall margin, the engine is uptrimmed for more thrust by increasing engine pressure ratio (EPR). The EPR uptrim logic has been evaluated and implemented into computer simulations. Thrust improvements over 10 percent are predicted for subsonic flight conditions. The EPR uptrim was successfully demonstrated during engine ground tests. Test results verify model predictions at the conditions tested.

Ray, R. J.↗

NASA and general aviation

General aviation remains the single most misunderstood sector of aeronautics in the United States. A detailed look at how general aviation functions and how NASA helps keep it on the cutting edge of technology in airfoils, airframes, commuter travel, environmental concerns, engines, propellers, air traffic control, agricultural development, electronics, and safety is given.

Ethell, J. L.↗

Modified US Army U-8F ground vibration test

The Dryden Flight Research Facility of NASA Ames Research Center conducted a ground vibration test on a modified U.S. Army U-8F airplane. Modifications included new engines, propellers, and engine-mounted truss assemblies. The ground vibration test was conducted using sine dwell, single-point random, and impact excitations. The test was performed to determine modal frequencies, mode shapes, and structural damping coefficients of the airframe and propeller with full and empty fuel tanks. The data presented include frequency response plots, rigid-body and structural modal frequencies, and mode shapes.

Kehoe, M. W.↗

Study of turbine bypass remote augmentor lift system for V/STOL aircraft

The airframe design and engine/aircraft integration were emphasized in a NASA comparative study of turbofan and turbine bypass engine (TBE) with remote augmentor lift systems (RALS) for supersonic V/STOL aircraft. Functional features of the TBE are reviewed, noting the enhanced cycle efficiency and reduced afterbody drag compared to the turbojets. The present studies examied performance levels for aircraft with fleet defense and secondary anti-surface warfare roles, carrying AMRAAM and AIM missiles. TBE engine cycles were configured for hover and up-and-away flight from deck launch, and all tests were done from a conceptual design viewpoint. The results indicate that the TBE-RALS is superior to turbofan-RALS aircraft in both gross take-off weight and life cycle cost.

Sheridan, A. E.↗