Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Large-scale advanced propeller blade pressure distributions: Prediction and data

Two Euler analyses techniques, finite difference and finite volume, were employed to predict the blade surface pressure distributions of a large scale advanced propeller. The predicted pressure distributions were compared with wind tunnel data. Both techniques produced blade pressure distributions that are in fairly good agreement with the data over the range of test Mach numbers of 0.2 to 0.78. However, the numerical simulations fail to predict correctly the measured pressure distributions for the low Mach number, high power case. The data indicate the presence of a leading edge vortex for this case. A discussion of the compressibility effects is also presented.

Nallasamy, M.↗

Unsteady blade surface pressures on a large-scale advanced propeller - Prediction and data

An unsteady three dimensional Euler analysis technique is employed to compute the flowfield of an advanced propeller operating at an angle of attack. The predicted blade pressure waveforms are compared with wind tunnel data at two Mach numbers, 0.5 and 0.2. The inflow angle is three degrees. For an inflow Mach number of 0.5, the predicted pressure response is in fair agreement with data: the predicted phases of the waveforms are in close agreement with data while the magnitudes are underpredicted. At the low Mach number of 0.2 (take-off) the numerical solution shows the formation of a leading edge vortex which is in qualitative agreement with measurements. However, the highly nonlinear pressure response measured on the blade suction surface is not captured in the present inviscid analysis.

Nallasamy, M.↗

Flow properties of the solar wind obtained from white light data, Ulysses observations and a two-fluid model

Using the empirical constraints provided by observations in the inner corona and in interplanetary space. we derive the flow properties of the solar wind using a two fluid model. Density and scale height temperatures are derived from White Light coronagraph observations on SPARTAN 201-1 and at Mauna Loa, from 1.16 to 5.5 R, in the two polar coronal holes on 11-12 Apr. 1993. Interplanetary measurements of the flow speed and proton mass flux are taken from the Ulysses south polar passage. By comparing the results of the model computations that fit the empirical constraints in the two coronal hole regions, we show how the effects of the line of sight influence the empirical inferences and subsequently the corresponding numerical results.

Habbal, Shadia Rifai↗

Space shuttle phase B wind tunnel model and test information. Volume 1: Booster configuration

Archived wind tunnel test data are available for flyback booster or other alternative recoverable configurations as well as reusable orbiters studied during initial development (Phase B) of the Space Shuttle. Considerable wind tunnel data was acquired by the competing contractors and the NASA Centers for an extensive variety of configurations with an array of wing and body planforms. All contractor and NASA wind tunnel test data acquired in the Phase B development have been compiled into a database and are available for application to current winged flyback or recoverable booster aerodynamic studies. The Space Shuttle Phase B Wind Tunnel Database is structured by vehicle component and configuration type. Basic components include the booster, the orbiter and the launch vehicle. Booster configuration types include straight and delta wings, canard, cylindrical, retroglide and twin body. Orbiter configuration types include straight and delta wings, lifting body, drop tanks, and double delta wings. Launch configurations include booster and orbiter components in various stacked and tandem combinations. This is Volume 1 (Part 1) of the report -- Booster Configuration.

Glynn, J. L.↗

Space shuttle phase B wind tunnel model and test information. Volume 1: Booster configuration

Archived wind tunnel test data are available for flyback booster or other alternative recoverable configurations as well as reusable orbiters studied during initial development (Phase B) of the Space Shuttle. Considerable wind tunnel data was acquired by the competing contractors and the NASA Centers for an extensive variety of configurations with an array of wing and body planforms. All contractor and NASA wind tunnel test data acquired in the Phase B development have been compiled into a database and are available for application to current winged flyback or recoverable booster aerodynamic studies. The Space Shuttle Phase B Wind Tunnel Database is structured by vehicle component and configuration type. Basic components include the booster, the orbiter, and the launch vehicle. Booster configuration types include straight and delta wings, canard, cylindrical, retroglide and twin body. Orbiter configuration types include straight and delta wings, lifting body, drop tanks and double delta wings. Launch configurations include booster and orbiter components in various stacked and tandem combinations. This is Volume 1 (Part 2) of the report -- Booster Configuration.

Glynn, J. L.↗

Spherical balloon wind sensor behavior.

Freely rising superpressure spherical balloon response characteristics based on wind profile data, showing surface roughness effects on aerodynamic properties

BALLOON FLIGHT↗

Interdecadal Variations in the Alaska Gyre

Climatic dynamic topography variations in the Alaska gyre during the period 1968-1990 are described with an objective analysis of more than 12000 STD and XBT stations, and COADS wind stress data Interannual the dynamic height and SST variations were correlated and were consistent with recently described large-scale climatic shifts in the North Pacific. The gyre was centered more to the east, circulation appeared stronger, and SST was lower during the early to mid-1970s than during the 1980s. The Aleutian low (NP and PNA indices) intensified during the interim, but the response did not appear as a gyre spinup. Instead, the associated wind stress anomalies forced a slowly varying dynamic height anomaly across the eastern and northern part of the gyre through Ekman convergence, which had the effect of displacing the gyre's low somewhat to the WSW in the 1980s. The wind curl spectrum was white, and the slow oceanic response was modeled as stochastic-forced climate variability with a simple first-order Markov autoregression process. Forcing was assumed to be Ekman pumping of the pycnocline, and the damping coefficient was estimated from the data to be approx. 1 yr. A hindcast with observed winds gave estimated dynamic height patterns similar to those observed, with a canonical correlation of 0.79 at 99% confidence. This response was weak in the western half of the gyre, where slow baroclinic variability may have been influenced by long Rossby wave propagation. A simple autoregression simulation using artificial white noise forcing shows the evolution of decadal variations similar in nature to those observed. This result, along with the low frequency correlation between dynamic height and SST, suggests that the upper-ocean climatic variability in this region is primarily wind forced.

Lagerloef, Gary S.E.↗

Stability and control derivatives of the lifting body vehicles

Predictions of the flight characteristics of lifting bodies have been based almost exclusively on wind-tunnel data for small-scale models. A need thus exists to compare the results from small-scale and full-scale wind-tunnel tests with results from flight tests to establish some measure of the accuracy of the predictions and to assess the sensitivity of the vehicle's handling qualities to typical discrepancies between flight and wind-tunnel results. Comparisons of these types have been one of the primary objectives of the M2-F2, HL-10, and X-24A flight programs. In this paper the more important longitudinal and lateral-directional aerodynamic stability and control derivatives obtained from flight are compared with small- and full-scale wind-tunnel results where applicable. Significant trends and important differences are pointed out, and the implications discussed.

Robert W Kempel↗

A preliminary comparison between the SR-6 propeller noise in flight and in a wind tunnel

High speed turboprops offer an attractive candidate for aircraft because of their high propulsive efficiency. However, one of the possible problems associated with these propellers is their high noise level at cruise condition that may create a cabin environment problem. Models of these propellers were tested for acoustics in the 8 by 6-foot wind tunnel and on the Jet Star airplane. Comparisons between the airplane and wind tunnel data for the SR-6 propeller are shown. The comparison of maximum blade passing tone variation with helical tip Mach number between the tunnel and flight data was good when corrected to the same test conditions. Directivity comparisons also showed fairly good agreement. These good comparisons indicate that the wind tunnel is a viable location for measuring the blade passage tone noise of these propellers.

Dittmar, J. H.↗

Progress in Flaps Down Flight Reynolds Number Testing Techniques at the NTF

A series of NASA/Boeing cooperative low speed wind tunnel tests was conducted in the National Transonic Facility (NTF) between 2003 and 2004 using a semi-span high lift model representative of the 777-200 aircraft. The objective of this work was to develop the capability to acquire high quality, low speed (flaps down) wind tunnel data at up to flight Reynolds numbers in a facility originally optimized for high speed full span models. In the course of testing, a number of facility and procedural improvements were identified and implemented. The impact of these improvements on key testing metrics data quality, productivity, and so forth - was significant, and is discussed here, together with the relevance of these metrics as applied to cryogenic wind tunnel testing in general. Details of the improvements at the NTF are discussed in AIAA-2006-0508 (Recent Improvements in Semi-span Testing at the National Transonic Facility). The development work at the NTF culminated with validation testing of a 787-8 semi-span model at full flight Reynolds number in the first quarter of 2006.

Payne, Frank↗

Flight test data for light aircraft spoiler roll control systems

The results of flight tests to determine the characteristics of spoiler roll control systems on three different light aircraft are summarized. Comparisons are made with wind tunnel data where available. Flight tests indicate that excellent roll characteristics can be achieved with spoilers. Yaw coupling with roll control inputs is virtually eliminated. Roll rates remain high when flaps are deployed at low speed. Very mild nonlinearities in control effectiveness exist, and there was no deadband or lag detected.

Kohlman, D. L.↗

Flight test data for light aircraft spoiler roll control systems

The results of flight tests to determine the characteristics of spoiler roll control systems on three different light aircraft are summarized. Comparisons are made with wind tunnel data where available. Flight tests indicate that excellent roll characteristics can be achieved with spoilers. Yaw coupling with roll control inputs is virtually eliminated. Roll rates remain high when flaps are deployed at low speed. Very mild nonlinearities in control effectiveness exist and there was no deadband or lag detected.

Kohlman, D. L.↗

Unsteady blade-surface pressures on a large-scale advanced propeller: Prediction and data

An unsteady 3-D Euler analysis technique is employed to compute the flow field of an advanced propeller operating at an angle of attack. The predicted blade pressure waveforms are compared with wind tunnel data at two Mach numbers, 0.5 and 0.2. The inflow angle is three degrees. For an inflow Mach number of 0.5, the predicted pressure response is in fair agreement with data: the predicted phases of the waveforms are in close agreement with data while the magnitudes are underpredicted. At the low Mach number of 0.2 (takeoff), the numerical solution shows the formation of a leading edge vortex which is in qualitative agreement with measurements. However, the highly nonlinear pressure response measured on the blade suction surface is not captured in the present inviscid analysis.

Nallasamy, M.↗

Detection and Use of Load and Gage Output Repeats of Wind Tunnel Strain-Gage Balance Data

Criteria are discussed that may be used for the detection of load and gage output repeats of wind tunnel strain-gage balance data. First, empirical thresholds are introduced that help determine if the loads or electrical outputs of a pair of balance calibration or check load data points match. A threshold of 0.01 percent of the load capacity is suggested for the identification of matching loads. Similarly, a threshold of 0.1 microV/V is recommended for the identification of matching electrical outputs. Two examples for the use of load and output repeats are discussed to illustrate benefits of the implementation of a repeat point detection algorithm in a balance data analysis software package. The first example uses the suggested load threshold to identify repeat data points that may be used to compute pure errors of the balance loads. This type of analysis may reveal hidden data quality issues that could potentially be avoided by making calibration process improvements. The second example uses the electrical output threshold for the identification of balance fouling. Data from the calibration of a six-component force balance is used to illustrate the calculation of the pure error of the balance loads.

strain-gage balance↗

Synthesis of rotor test data for real-time simulation

A mathematical model of a hingeless tilting rotor is presented. The model was obtained by a systematic curve fit procedure applied to an extensive set of model scale wind tunnel data. The math model equations were used in a real time flight simulation model of a hingeless tilt rotor XV-15 to assess changes in flying qualities compared to those obtained using a previous rotor model. Extensive plots of the rotor derivatives are given. Discussions of attempts to apply multivariable linear regression technqiues to the data and the use of an analytical rotor representation are included.

Mcveigh, M. A.↗

Flight-Measured Aerodynamic Loads on a 0.92 Aspect Ratio Lifting Surface

Ventral fin loads, expressed as normal force coefficients, bending moment coefficients, and torque coefficients, were measured during flight tests of a YF-12A airplane. Because of the proximity of the ventral fin to the ailerons, the aerodynamic loads presented were the result of both sideslip loads and aileron crossflow loads. Aerodynamic data obtained from strain gage loads instrumentation and some flight pressure measurements are presented for several Mach numbers ranging from 0.70 to 2.00. Selected wind tunnel data and results of linear theoretical aerodynamic calculations are presented for comparison.

Meyer, R. R., Jr.↗

Wind Field and Trajectory Models for Tornado-Propelled Objects

A mathematical model to predict the trajectory of tornado born objects postulated to be in the vicinity of nuclear power plants is developed. An improved tornado wind field model satisfied the no slip ground boundary condition of fluid mechanics and includes the functional dependence of eddy viscosity with altitude. Subscale wind tunnel data are obtained for all of the missiles currently specified for nuclear plant design. Confirmatory full-scale data are obtained for a 12 inch pipe and automobile. The original six degree of freedom trajectory model is modified to include the improved wind field and increased capability as to body shapes and inertial characteristics that can be handled. The improved trajectory model is used to calculate maximum credible speeds, which for all of the heavy missiles are considerably less than those currently specified for design. Equivalent coefficients for use in three degree of freedom models are developed and the sensitivity of range and speed to various trajectory parameters for the 12 inch diameter pipe are examined.

Redmann, G. H.↗