Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface wave”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Multi-user satellite communications system using an innovative compressive receiver

There is a need for an onboard simultaneous multi-channel demodulation system for a satellite communications system. Studies indicate that Convolve Multiply Convolve (CMC) filtering with surface acoustic wave (SAW) dispersive delay lines will eliminate the necessity of onboard satellite channelized filters of complex fourier transform processors. The reason for choosing the CMC technique is its ability to perform Fourier transformations in a shorter time with less space and power consumption than digital Fourier transform processors. Each ground terminal in this multi-users communications system is remotely located and operates independently; hence, a method of synchronizing the transmission of these users is presented which utilizes the existing Global Positioning System (GPS) system. Each ground user is equipped with a low cost ground terminal that has a synchronization subsystem attached to it. The system design of an onboard Multi-channel Receiver and Demodulator utilizes Quadrature Phase Shift Keying (QPSK) as the modulation technique. This technique provides the best figure of merit, i.e., the lowest transmitter power requirement per communication channel.

Staples, Edward J.↗
NASA NTRS1990

Enhanced spectral efficiency using bandwidth switchable SAW filtering for mobile satellite communications systems

Currently proposed mobile satellite communications systems require a high degree of flexibility in assignment of spectral capacity to different geographic locations. Conventionally this results in poor spectral efficiency which may be overcome by the use of bandwidth switchable filtering. Surface acoustic wave (SAW) technology makes it possible to provide banks of filters whose responses may be contiguously combined to form variable bandwidth filters with constant amplitude and phase responses across the entire band. The high selectivity possible with SAW filters, combined with the variable bandwidth capability, makes it possible to achieve spectral efficiencies over the allocated bandwidths of greater than 90 percent, while retaining full system flexibility. Bandwidth switchable SAW filtering (BSSF) achieves these gains with a negligible increase in hardware complexity.

Peach, Robert↗
NASA NTRS1992

A new Lagrangian method for real gases at supersonic speed

With the renewed interest in high speed flights, the real gas effect is of theoretical as well as practical importance. In the past decade, upwind splittings or Godunov-type Riemann solutions have received tremendous attention and as a result significant progress has been made both in the ideal and non-ideal gas. In this paper, we propose a new approach that is formulated using the Lagrangian description, for the calculation of supersonic/hypersonic real gas inviscid flows. This new formulation avoids the grid generation step which is automatically obtained as the solution procedure marches in the 'time-like' direction. As a result, no remapping is required and the accuracy is faithfully maintained in the Lagrangian level. In this paper, we give numerical results for a variety of real gas problems consisting of essential elements in high speed flows, such as shock waves, expansion waves, slip surfaces and their interactions. Finally, calculations for flows in a generic inlet and nozzle are presented.

Loh, C. Y.↗
NASA NTRS1991

Miniaturized fiber-optic Michelson-type interferometric sensors

A novel, miniaturized Michelson-type fiber-optic interferometric sensor that is relatively insensitive to temperature drifts is presented. A fused-biconical tapered coupler is cleaved immediately after the coupled length and polished down to the region of the fused cladding, but short of the interaction region. The end of one core is selectively coated with a reflective surface and is used as the reference arm; the other core serves as the sensing arm. The detection of surface acoustic waves, microdisplacements, and magnetic fields is reported. The sensor is shown to be highly stable in comparison to a classic homodyne, uncompensated Michelson interferometer, and signal-to-noise ratios of 65 dB have been obtained.

Murphy, Kent A.↗
NASA NTRS1991

The EOSDIS Version 0 Distributed Active Archive Center for physical oceanography and air-sea interaction

The Distributed Active Archive Center (DAAC) at the Jet Propulsion Laboratory will support scientists specializing in physical oceanography and air-sea interaction. As part of the NASA Earth Observing System Data and Information System Version 0 the DAAC will build on existing capabilities to provide services for data product generation, archiving, distribution and management of information about data. To meet scientist's immediate needs for data, existing data sets from missions such as Seasat, Geosat, the NOAA series of satellites and the Global Positioning Satellite system will be distributed to investigators upon request. In 1992, ocean topography, wave and surface roughness data from the Topex/Poseidon radar altimeter mission will be archived and distributed. New data products will be derived from Topex/Poseidon and other sensor systems based on recommendations of the science community. In 1995, ocean wind field measurements from the NASA Scatterometer will be supported by the DAAC.

Hilland, Jeffrey E.↗
NASA NTRS1992

Results of a zonally truncated three-dimensional model of the Venus middle atmosphere

Although the equatorial rotational speed of the solid surface of Venus is only 4 m s(exp-1), the atmospheric rotational speed reaches a maximum of approximately 100 m s(exp-1) near the equatorial cloud top level (65 to 70 km). This phenomenon, known as superrotation, is the central dynamical problem of the Venus atmosphere. We report here the results of numerical simulations aimed at clarifying the mechanism for maintaining the equatorial cloud top rotation. Maintenance of an equatorial rotational speed maximum above the surface requires waves or eddies that systematically transport angular momentum against its zonal mean gradient. The zonally symmetric Hadley circulation is driven thermally and acts to reduce the rotational speed at the equatorial cloud top level; thus wave or eddy transport must counter this tendency as well as friction. Planetary waves arising from horizontal shear instability of the zonal flow (barotropic instability) could maintain the equatorial rotation by transporting angular momentum horizontally from midlatitudes toward the equator. Alternatively, vertically propagating waves could provide the required momentum source. The relative motion between the rotating atmosphere and the pattern of solar heating, which as a maximum where solar radiation is absorbed near the cloud tops, drives diurnal and semidiurnal thermal tides that propagate vertically away from the cloud top level. The effect of this wave propagation is to transport momentum toward the cloud top level at low latitudes and accelerate the mean zonal flow there. We employ a semispectral primitive equation model with a zonal mean flow and zonal wavenumbers 1 and 2. These waves correspond to the diurnal and semidiurnal tides, but they can also be excited by barotropic or baroclinic instability. Waves of higher wavenumbers and interactions between the waves are neglected. Symmetry about the equator is assumed, so the model applies to one hemisphere and covers the altitude range 30 to 110 km. Horizontal resolution is 1.5 deg latitude, and vertical resolution is 1.5 km. Solar and thermal infrared heating, based on Venus observations and calculations drive the model flow. Dissipation is accomplished mainly by Rayleigh friction, chosen to produce strong dissipation above 85 km in order to absorb upward propagating waves and limit extreme flow velocities there, yet to give very weak Rayleigh friction below 70 km; results in the cloud layer do not appear to be sensitive to the Rayleigh friction. The model also has weak vertical diffusion, and very weak horizontal diffusion, which has a smoothing effect on the flow only at the two grid points nearest the pole.

Newman, M.↗
NASA NTRS1992

One GHz leaky SAW velocity of metal layers and bilayers evaporated onto fused quartz

An acoustic microscope operating at 1 GHz was used to determine the surface acoustic wave velocities v of thin film metal layers and metal bilayers deposited onto fused quartz. V(0)'s influence was reduced by gating. This produced a calibrated accuracy of 3 percent. A program was constructed from the explicitly solved 6 x 6 theoretical determinant. Single film thicknesses were decided upon by using this theory to produce a v equal to a standard. Since the single film v's were linear with respect to their thickness, half the single film thicknesses were used for the bilayered films. The velocities for these bilayered films agreed with theory. This experimentally confirms the theoretical technique used here to examine bilayered systems, or a prototype composite interphase. No discrepancy was seen for gold films as others have reported. V(z) seemed insensitive to the formation of intermetallics or CuO. Some annealed and unannealed platinum films did not change the v from that of fused quartz. Two platinum films whose v's were in agreement with theory peeled off with the tape test.

Walikainen, Dale↗
NASA NTRS1992

Sapphire fiber interferometer for microdisplacement measurements at high temperature

Attention is given to the use of a short-length multimode sapphire rod as an extension to a conventional Michelson interferometric configuration, but with operation of Fabry-Perot cavity-based sensor element type. The performance of such a device as an interferometric sensor is demonstrated for a case where the interference between the reflections from the sapphire-air interface and an air-metallic surface is inspected for microdisplacements of the metallic surface. A detailed account is given of the sensor's fabrication procedure; results are presented for the detection of surface-acoustic waves.

Murphy, Kent A.↗
NASA NTRS1991

Sapphire fiber interferometer for microdisplacement measurements at high temperatures

We report the use of a short-length, multimode sapphire rod as an extension to a Michelson configuration, but operated as a low-finesse Fabry-Perot cavity. We demonstrate the performance of such a device as an interferometric sensor, where the interference between the reflections from the sapphire-air interface and an air-metallic surface is observed for microdisplacement of the metallic surface which is placed close to the sapphire endface. We describe in detail the fabrication procedure and present results obtained from the detection of temperature changes, applied strain, and surface acoustic waves.

Murphy, Kent A.↗
NASA NTRS1993

SAW based systems for mobile communications satellites

Modern mobile communications satellites, such as INMARSAT 3, EMS, and ARTEMIS, use advanced onboard processing to make efficient use of the available L-band spectrum. In all of these cases, high performance surface acoustic wave (SAW) devices are used. SAW filters can provide high selectivity (100-200 kHz transition widths), combined with flat amplitude and linear phase characteristics; their simple construction and radiation hardness also makes them especially suitable for space applications. An overview of the architectures used in the above systems, describing the technologies employed, and the use of bandwidth switchable SAW filtering (BSSF) is given. The tradeoffs to be considered when specifying a SAW based system are analyzed, using both theoretical and experimental data. Empirical rules for estimating SAW filter performance are given. Achievable performance is illustrated using data from the INMARSAT 3 engineering model (EM) processors.

Peach, R. C.↗
NASA NTRS1992

Advanced satellite communication system

The objective of this research program was to develop an innovative advanced satellite receiver/demodulator utilizing surface acoustic wave (SAW) chirp transform processor and coherent BPSK demodulation. The algorithm of this SAW chirp Fourier transformer is of the Convolve - Multiply - Convolve (CMC) type, utilizing off-the-shelf reflective array compressor (RAC) chirp filters. This satellite receiver, if fully developed, was intended to be used as an on-board multichannel communications repeater. The Advanced Communications Receiver consists of four units: (1) CMC processor, (2) single sideband modulator, (3) demodulator, and (4) chirp waveform generator and individual channel processors. The input signal is composed of multiple user transmission frequencies operating independently from remotely located ground terminals. This signal is Fourier transformed by the CMC Processor into a unique time slot for each user frequency. The CMC processor is driven by a waveform generator through a single sideband (SSB) modulator. The output of the coherent demodulator is composed of positive and negative pulses, which are the envelopes of the chirp transform processor output. These pulses correspond to the data symbols. Following the demodulator, a logic circuit reconstructs the pulses into data, which are subsequently differentially decoded to form the transmitted data. The coherent demodulation and detection of BPSK signals derived from a CMC chirp transform processor were experimentally demonstrated and bit error rate (BER) testing was performed. To assess the feasibility of such advanced receiver, the results were compared with the theoretical analysis and plotted for an average BER as a function of signal-to-noise ratio. Another goal of this SBIR program was the development of a commercial product. The commercial product developed was an arbitrary waveform generator. The successful sales have begun with the delivery of the first arbitrary waveform generator.

Staples, Edward J.↗
NASA NTRS1994

Using a temperature-controlled quartz crystal microbalance in a space equipment cleanroom to monitor molecular contamination

There is a need for continuous monitoring for molecular contamination in clean rooms where spaceflight equipment is assembled, integrated, and tested to insure that contamination budgets are met. The TQCM (temperature-controlled quartz crystal microbalance) can be used to provide both a real time warning and a cumulative measurement of molecular contamination. It has advantages over the other measurement methods such as witness mirrors, NVR (non-volatile residue) plates, and gas analyzers. A comparison of the TQCM sensitivity and ease of operations is made with the other methods. The surface acoustic wave microbalance (SAW), a newly developed instrument similar to TQCM, is considered in the comparison. An example is provided of TQCM use at Goddard Space Flight Center when the Wide Field Planetary Camera 2(WFPC-2) and the Corrective Optics Space Telescope Axial Replacement (COSTAR) were undergoing integrated testing prior to their installation in the Hubble Space Telescope on its first servicing mission. Areas for further investigation are presented.

Mitchell, William J.↗
NASA NTRS1994

Effect of nonlinear interactions on p-mode frequencies and line widths

We calculate the effect of nonlinear interactions among solar acoustic modes upon the modal frequencies and energy loss rates (or line widths). The frequency shift for a radial p-mode of frequency 3 mHz is found to be about -0.5 microHz. The magnitude of nonlinear frequency shift increases more rapidly with frequency than the inverse mode mass (mode mass is defined as the ratio of energy in the mode to its surface velocity amplitude squared). This frequency shift is primarily due to nonresonant three-mode interactions and is dominated by high l surface gravity waves (f-modes) and p-modes. The line width of a radial p-mode of frequency 3 mHz, due to resonant nonlinear interactions, is about 0.3 microHz. This result is consistent with that of Kumar and Goldreich (1989). We also find, in agreement with these authors, that the most important nonlinear interactions of trapped p-modes involve f-modes and high-frequency p-modes (frequency greater than about 5 mHz) which propagate in the solar photosphere. Thus, using the arguments advanced by Kumar & Goldreich (1989), we conclude that nonlinear couplings cannot saturate the overstable solar p-modes at their small observed amplitudes. Both the nonlinear frequency shifts and line widths, at a fixed frequency, are proportional to the inverse of mode mass which for modes of degree greater than about 100 is approximately l(exp 0.8). Therefore, the frequency of an f-mode of l = 1000, due to nonlinear interactions, is decreased by approximately 0.4%.

Kumar, Pawan↗
NASA NTRS1995

An X-ray and optical study of the interaction of the Cygnus Loop supernova remnant with an interstellar cloud

We have used the ROSAT high-resolution imager and optical emission line data to study the structure of a bright optical knot on the southeastern rim of the Cygnus Loop supernova remnant. This knot has been identified as an encounter between the blast wave and a small isolated cloud. The knot appears in projection just behind the blast wave, which is traced by Balmer line filaments which bound the X-ray emission. The knot is a prominent X-ray feature, consisting of a numerb of filaments which are correlated with the optical line emission. These data permit a detailed view of the blast wave interaction. By combining the optical and X-ray data it is possible to trace the blast wave as a continuous surface from its southern edge around the western side of the cloud that then continues on to the north. The southeastern knot is an indentation on the surface of the blast wave. Thus the southeastern knot is not a small cloud that has been overrun by the blast wave, but the tip of a larger cloud. Bright X-ray emission is associated with bright radiative filaments. The location of this emission, upstream of the radiative shocks, implies that the enhanced X-rays come from a reverse shock. The presence of a reverse shock is further evidence that the southeastern knot represents an early stage of a blast wave encountering a large cloud. A consistent picture of the Cygnus Loop as an explosion within a preexisting cavity is emerging. These observations agree with that picture.

Graham, James, R.↗
NASA NTRS1994

Reflection Properties of Metallic Gratings on ZnO Films over GaAs Substrates

A potential application for piezoelectric film deposited on GaAs substrates is the monolithic integration of surface acoustic wave (SAW) devices with GaAs electronics. Metallic gratings are basic elements required for the construction of such devices, and analyzing the reflectivity and the velocity change due to metallic gratings is often a critical design parameter. In this article, Datta and Hunsinger technique is extended to the case of a multilayered structure, and the developed technique is applied to analyze shorted and open gratings on ZnO films sputtered over (001)-cut (110)-propagating GaAs substrates. The analysis shows that zero reflectivity of shorted gratings can be obtained by a combination of the ZnO film and the metal thickness and the metalization ratio of the grating. Experiments are performed on shorted and an open gratings (with the center frequency of about 180 MHz) for three different metal thicknesses over ZnO films which are 0.8 and 2.6 micrometers thick. From the experiments, zero reflectivity at the resonant frequency of the grating is observed for a reasonable thickness (h/Alpha = 0.5%) of aluminum metalization. The velocity shift between the shorted and the open grating is also measured to be 0.18 MHz and 0.25 MHz for 0.8 and 1.6 micrometers respectively. The measured data show relatively good agreement with theoretical predictions.

Hickernell, Fred S.↗
NASA NTRS1997

Calibration of the QCM/SAW Cascade Impactor for Measurement of Ozone in the Stratosphere

The Quartz Crystal Microbalance Surface Acoustic Wave (QCM/SAW) cascade impactor collects size-fractionated distributions of aerosols on a series of 10 MHz quartz crystals and employs SAW devices coated with chemical sensors for gas detection. Presently, we are calibrating the ER-2 certified QCM/SAW cascade impactor in the laboratory for the detection of ozone. Experiments have been performed to characterize the QCM and SAW mass loading, saturation limits, mass frequency relationships, and sensitivity. We are also characterizing sampling efficiency by measuring the loss of ozone on different materials. There are parallel experiments underway to measure the variations in the sensitivity and response of the QCM/SAW crystals as a function of temperature and pressure. Results of the work to date will be shown.

Wright, Cassandra K.↗
NASA NTRS1997

New Polymer Coatings for Chemically Selective Mass Sensors

There is a current need to develop sensitive and chemically specific sensors for the detection of nitric acid for in-situ measurements in the atmosphere. Polymer coatings have been synthesized and tested for their sensitivity and selectivity to nitric acid. A primary requirement for these polymers is detectability down to the parts per trillion range. The results of studies using these polymers as coatings for quartz crystal microbalances (QCM) and surface acoustic wave (SAW) devices will be presented.

Sims, S. C.↗
NASA NTRS1997

FTIR Spectroscopy of HNO3 and NO2 Relevant to Stratospheric Wake Analysis

The Fourier Transform Infrared (FTIR) technique has been employed to measure absolute concentrations of nitric acid (HNO3) and nitrogen dioxide (NO2) with 1/cm resolution and an absorption pathlength of 4 m under quasi-static and flow conditions at atmospheric pressure and room temperature. Water features seen under quasi-static conditions diminished in intensity under flowing conditions. Nitric acid was observed in the 1660-1760/cm range, while nitrogen dioxide was detected both in the 1536-1660 and 1213-1400/cm ranges. Concentrations of nitrogen dioxide and nitric acid were determined to be 11.9 and 4.35 parts per million (ppm), respectively, with an uncertainty of 0.2 ppm. Experiments are underway with a 10 m cell to measure the absorption of nitric acid, water, sulfur dioxide, hydrochloric acid and ammonia on various materials such as glass, teflon, stainless steel and aluminum used for implementation of the flow system. Such materials will be used for the measurements of stratospheric trace gases by the Quartz Crystal Microbalance (QCM) and Surface Acoustic Wave (SAW) devices.

Abina, Rafiu A.↗