Results for “streaming data” — Page 61

NASA NTRSDate not supplied

Comparison of Surface Pressure Fluctuations from Flight and Wind Tunnel Tests on the Orion Multi-Purpose Crew Vehicle

Transonic and supersonic wind-tunnel test of scaled-models are used to predict the surface pressure fluctuations on aerospace vehicles. An outstanding question is how good are such tests? The present paper attempts to answer this question for the Multi-Purpose Crew Vehicle by comparing data from the Ascent Abort-2 (AA2) flight test with those measured in two different scaled-model wind tunnel tests (WTT) 51AS and 134AS. A sensor by sensor and a Mach by Mach comparisons of spectra of surface pressure fluctuations are presented for nominal ascent part of flight. Spectra measured over a large part of the vehicle surface were found to be dominated by the wake vortices shed from the four Abort Motor nozzles situated on the upper part of the Launch Abort System. It was found that the shapes of the scaled-up spectra from WTTs were very close to those measured in the flight, but the levels, for the most part, were found to be lower than the flight data. The highest differences were from the regions of complex flows where wakes from the adjacent nozzles interacted with the free-stream flow. There the WTT predicted levels were consistently 2dB to 6dB lower than the flight data, across all spectral bands. Another region of significant under-prediction was the local separated flow region at the Fillet-Ogive junction. The accuracy of the sharp spectral peaks from regions along a nozzle axis was found to be dependent on the fidelity of the model. The model in the 51AS WTT used a simplified contour, which resulted in a large under prediction of the spectral peak by 1dB to 10dB. A limited number of data from 134AS, where the model accurately captured all features of the nozzles of the flight vehicle, however; showed that the under prediction was lower: 1-2dB. The fluctuation spectra on the large protuberance of the Umbilical Cover was found to be reasonably well-predicted by 134AS WTT, which meticulously reproduced a scaled-down shape of this protuberance. Such information will help to determine the margins to be applied to wind-tunnel data to create flight environments.

MPCV↗

NASA NTRS1984

An experimental investigation of the effect of boundary layer refraction on the noise from a high-speed propeller

Models of supersonic propellers were previously tested for acoustics in the Lewis 8- by 6-Foot Wind Tunnel using pressure transducers mounted in the tunnel ceiling. The boundary layer on the tunnel ceiling is believed to refract some of the propeller noise away from the measurement transducers. Measurements were made on a plate installed in the wind tunnel which had a thinner boundary layer than the ceiling boundary layer. The plate was installed in two locations for comparison with tunnel ceiling noise data and with fuselage data taken on the NASA Dryden Jetstar airplane. Analysis of the data indicates that the refraction increases with: increasing boundary layer thickness; increasing free stream Mach number; increasing frequency; and decreasing sound radiation angle (toward the inlet axis). At aft radiation angles greater than about 100 deg there was little or no refraction. Comparisons with the airplane data indicated that not only is the boundary layer thickness important but also the shape of the velocity profile. Comparisons with an existing two-dimensional theory, using an idealized shear layer to approximate the boundary layer, showed that the theory and data had the same trends. Analysis of the data taken in the tunnel at two different distances from the propeller indicates a decay with distance in the wind tunnel at high Mach numbers but the decay at low Mach numbers is not as clear.

Dittmar, J. H.↗

NASA NTRS1999

Variability in Sea Surface Height: A Qualitative Measure for the Meridional Overturning in the North Atlantic

Sea surface height (SSH) from altimeter observations from 1992 on and from modeling results is investigated to determine the modes of variability and the linkages to the state of oceanic circulation in the North Atlantic. First the altimeter and model simulated SSH are analyzed using the empirical orthogonal function (EOF) analysis. They are found to share a similar leading mode where the center of action is along the Gulf Stream and North Atlantic Current with opposite sign anomalies in the subpolar gyre and in the slope waters along the Eastern Seaboard. The time series of the leading EOF mode from the altimeter data shows that between winters of 1995 and 1996, SSH over the Gulf Stream decreased by about 12cm which change is reproduced by the model simulation. Based on the relationship from the model simulations between the time series of the SSH EOF1 and meridional heat transport, it is suggested that associated with this SSH change in 1995-96, the overturning has slowed down from its heights in the early 90's. Furthermore, it is shown that decadal variability in the leading SSH mode originates from the thermal forcing component. This adds confidence to the qualitative relationship between the state of overturning/meridional heat transport and SSH in the limited area described by the EOF1. SSH variability in the eastern side of the North Atlantic basin, outside the western boundary current region, is determined by local and remote (Rossby waves) wind stress curl forcing.

Hakkinen, Sirpa↗

NASA NTRS1984

The 1984 NASA/ASEE summer faculty fellowship program

The assessment of forest productivity and associated nitrogen flux in a number of conifer ecosystems is described. As a base line study of acid precipitation in the Sierra Nevada, involved is the extraction and integration of a number of data planes describing the terrain, soils, lithology, vegetation cover and structure, and microclimate of the region. The development of automated techniques to extract topographic networks (stream canyons and ridge lines) for use as a landscrape skeleton to organize and integrate data sets into an efficient geographical information system is examined. The software is written in both FORTRAN and C, and is portable to a number of different computer environments with minimal modification.

Source record↗

NASA NTRS1974

Wind-tunnel investigation of an externally blown flap STOL transport model including and investigation of wall effects

A wind-tunnel investigation was conducted in the Langley V/STOL tunnel and in a scaled version of the Ames 40- by 80-foot tunnel test section installed as a liner in the Langley V/STOL tunnel to determine the effect of test-section size on aerodynamic characteristics of the model. The model investigated was a swept-wing, jet-powered, externally blown flap (EBF) STOL transport configuration with a leading-edge slat and triple-slotted flaps. The model was an 0.1645-scale model of a 11.58-meter (38.0-ft) span model designed for tests in a 40- by 80-foot tunnel. The data compare the aerodynamic characteristics of the model with and without the tunnel liner installed. Data are presented as a function of thrust coefficient over an angle-of-attack range of 0 deg to 25 deg. A thrust-coefficient range up to approximately 4.0 was simulated, most ot the tests being conducted at a free-stream dynamic pressure of 814 Newtons/sq m (17 lb sq ft). The data are presented with a minimum of analysis.

Gentry, G. L., Jr.↗

NASA NTRS1999

Assimilation of Satellite Altimeter Data With a Four Dimensional Model of the Japan Sea

A data assimilation is carried out to detect the variability of the Japan Sea circulation in the range from a few days to several years and from eddy to basin scale. The model applied in this study is the same 1/6 degree GFDL MOM1 as Kim and Yoon (1999) but is driven by ECMWF daily wind stress, heat and fresh water fluxes. The satellite altimeter data of TOPEX/POSEIDON, ERS-1 (phase C and G) and -2 are assimilated by an approximate Kalman filter (Fukumori and M.Rizzoli, 1995). The approximation is made by seeking an asymptotic steady error covariance matrix (Fukumori et al., 1993) and by introducing a coarser grid model for the innovation (data-model misfit). The coarse grid model is defined on 1/2 degree horizontal resolution and consists of the barotropic stream function, first baroclinic displacement and velocity amplitudes. The assimilated estimates explain about 6cm sea level variability of the data (approximately 12cm in the southern part), which is much larger than the previous reduced-gravity model and TOPEX/POSEIDON altimeter data assimilation (Hirose et al., 1999). The impacts of the T/P and ERS data on the filtered estimates are comparable. The result also shows high correlation to subsurface water temperatures measured by CTD. Many of the mesoscale eddies/disturbances travel east-northeastward with the advection speed of 1-3cm/s though most of them generated in the western region can not pass over the Oki Spur. The quasi-biennial variability found by Hirose and Ostrovskii (1999) did not show clear propagation pattern. The shallow Oki Spur may work as a "western boundary" to this signal. This is more plausible estimation than by the R-G model which has no bottom topography.

Hirose, Naoki↗

NASA NTRSDate not supplied

Validation of Cryogenic Propellant Tank Self-Pressurization

NASA’s near-future long-term space missions necessitate advancements in cryogenic fluid management (CFM), which includes safe and reliable long-term propellant storage. Consequently, NASA STMD (Space Technology Mission Directorate) has established the CFM Portfolio Project to improve CFM technologies for upcoming missions. As a part of CFM Modeling Portfolio, NASA Marshall Space Flight Center’s (MSFC) Fluid Dynamics branch within the Propulsion Systems Department is tasked with assessing and improving computational tools used to support flight projects such as Human Lander System and Commercial Lunar Payload Services. One of the challenging modeling problems is that of self-pressurization of propellant tank due to heat leakage over long time periods. Reduced order and nodal tools find it extremely difficult to accurately predict self-pressurization under transient conditions or where complex flow patterns or thermal gradients exist, and application of 3-D CFD (computational fluid dynamics) simulations is necessary to characterize these problems. Until recently, CFD simulations for these long-term processes (order of hours or days) have been too impractical to conduct due to prohibitive wall time and computational resource requirements. The requisite CFD tool need to be efficient, computationally scalable, modular with ability to incorporate various physics models, and robust enough to not accumulate conservation errors over several hours of simulated time. NASA MSFC’s Loci-Stream CFD tool along with the VOF module is a great candidate to fit this mold. In this paper, we validate Loci-Stream for predicting self-pressurization of a flight scale propellant tank so it can serve as a reliable design and analysis tool for NASA’s CFM application needs. Liquid hydrogen tank pressurization tests carried out at the K-site testing facility provide a reliable data set for this purpose. These tests were simulated using Loci-Stream solver with VOF module as well as a hybrid approach which uses a lumped model for the ullage gas domain and CFD simulation of the liquid propellant. Both are shown to have very good predictive capabilities over multiple K-site experiments.

Hong Q. Yang↗

NASA NTRSDate not supplied

Validation of Cryogenic Propellant Tank Self-Pressurization

NASA's near-future long-term space missions necessitate advancements in cryogenic fluid management (CFM), which includes safe and reliable long-term propellant storage. Consequently, NASA STMD (Space Technology Mission Directorate) has established the CFM Portfolio Project to improve CFM technologies for upcoming missions. As a part of CFM Modeling Portfolio, NASA Marshall Space Flight Center's (MSFC) Fluid Dynamics branch within the Propulsion Systems Department is tasked with assessing and improving computational tools used to support flight projects such as Human Lander System and Commercial Lunar Payload Services. One of the challenging modeling problems is that of self-pressurization of propellant tank due to heat leakage over long time periods. Reduced order and nodal tools find it extremely difficult to accurately predict self-pressurization under transient conditions or where complex flow patterns or thermal gradients exist, and application of 3-D CFD (computational fluid dynamics) simulations is necessary to characterize these problems. Until recently, CFD simulations for these long-term processes (order of hours or days) have been too impractical to conduct due to prohibitive wall time and computational resource requirements. The requisite CFD tool need to be efficient, computationally scalable, modular with ability to incorporate various physics models, and robust enough to not accumulate conservation errors over several hours of simulated time. NASA MSFC's Loci-Stream CFD tool along with the VOF module is a great candidate to fit this mold. In this paper, we validate Loci-Stream for predicting self-pressurization of a flight scale propellant tank so it can serve as a reliable design and analysis tool for NASA's CFM application needs. Liquid hydrogen tank pressurization tests carried out at the K-site testing facility provide a reliable data set for this purpose. These tests were simulated using Loci-Stream solver with VOF module as well as a hybrid approach which uses a lumped model for the ullage gas domain and CFD simulation of the liquid propellant. Both are shown to have very good predictive capabilities over multiple K-site experiments.

cryogenic fluid management↗

NASA NTRS2004

Effect of aerosols and clouds on the retrieval of infrared sea surface temperatures

Comparisons are performed between spatially averaged sea surface temperatures (ASST2) as derived from the second Along-Track Scanning Radiometer (ATSR-2) on board the second European Remote Sensing Satellite (ERS-2) and the NOAA–NASA Advanced Very High Resolution Radiometer (AVHRR) Oceans Pathfinder dataset (MPFSST). Difference maps, MPFSST 2 ASST2, along with the application of a simple statistical regression model to aerosol and cloud data from the Total Ozone Mapping Spectrometer (TOMS), are used to examine the impact of possible aerosol and cloud contamination. Differences varied regionally, but the largest biases were seen off western Africa. Nighttime and daytime differences off western Africa were reduced from 20.58 to 20.28C and from 20.18 to 08C, respectively. Significant cloud flagging, based on the model, occurred in the Indian Ocean, the equatorial Pacific, and in the vicinity of the Gulf Stream. Comparisons of the MPFSST and the ASST2 with in situ data from the 2002 version of the World Oceanic Database (WOD02) off western Africa show larger mean differences for the MPFSST. The smallest mean differences occurred for nighttime ASST2 2 WOD02 with a value of 0.08 6 0.48C.

Armstrong, Edward M.↗

NASA NTRS1975

Calculation of the flow on a blunted cone at high angle of attack

A new technique for calculating the entire flow-field on spherically blunted circular cones at high angles of attack and high Reynolds numbers is described. The calculations are based on a single-layer system of three-dimensional parabolic equations which are approximations to the full steady Navier-Stokes equations. Initial conditions at the sphere-cone tangency plane are provided by using an inviscid time-dependent solution added to a viscous nonsimilar boundary layer solution. Calculated results are compared with experimental heat transfer and pressure data for a 15 deg half-angle cone with a 1-in. spherical nose at 15 deg angle of attack. The free-stream Mach number is 10.6, and the free-stream Reynolds number is 1,200,000 per foot. Excellent agreement between the calculated and experimental data for both pressure and heat transfer is obtained.

Lubard, S. C.↗

NASA NTRSDate not supplied

Validation of Loci-Stream for Autogenous Pressurization of Cryogenic Propellant Tank

Autogenous pressurization of cryogenic propellant tanks eliminates the need to have an additional pressurant tank on the space vehicle, which is highly advantageous due to reduced vehicle mass and design complexity. Autogenous pressurization therefore is one of the key technologies for deep space exploration and long-term space missions. The complex interaction of thermal gradients, turbulence and phase change near the interface make the problem a challenging one to model. Nodal analysis tools and reduced order models are unable to capture the necessary physics. 3-D CFD analyses are necessary to fully characterize autogenous pressurization. CFD analyses pose their own difficulties. The requisite CFD tool to tackle this problem need to be modular with the ability to incorporate various physics models, efficient, and computationally scalable for simulating flight size tanks. NASA MSFC's Loci-Stream CFD tool along with the VOF module is a great candidate to fit this mold. We demonstrate our modeling approach and validation of Loci-Stream for predicting autogenous pressurization of a flight scale propellant tank in order for the solver to serve as a reliable design and analysis tool for NASA's CFM application needs. Liquid hydrogen tank pressurization tests carried out at the MSFC test stand 300 facilities provide reliable validation data for this purpose. These tests were modeled using the Loci-Stream solver with a newly implemented two-phase sharp interface treatment. We show that our modeling approach and CFD solver predict the autogenous pressurization phenomena satisfactorily, and document challenging aspects of modeling this problem.

cryogenic fluid management↗

NASA NTRSDate not supplied

Validation of Loci-Stream for Autogenous Pressurization of Cryogenic Propellant Tank

Autogenous pressurization of cryogenic propellant tanks eliminates the need to have an additional pressurant tank on the space vehicle, which is highly advantageous due to reduced vehicle mass and design complexity. Autogenous pressurization therefore is one of the key technologies for deep space exploration and long-term space missions. The complex interaction of thermal gradients, turbulence and phase change near the interface make the problem a challenging one to model. Nodal analysis tools and reduced order models are unable to capture the necessary physics. 3-D CFD analyses are necessary to fully characterize autogenous pressurization. CFD analyses pose their own difficulties. The requisite CFD tool to tackle this problem need to be modular with the ability to incorporate various physics models, efficient, and computationally scalable for simulating flight size tanks. NASA MSFC's Loci-Stream CFD tool along with the VOF module is a great candidate to fit this mold. We demonstrate our modeling approach and validation of Loci-Stream for predicting autogenous pressurization of a flight scale propellant tank in order for the solver to serve as a reliable design and analysis tool for NASA's CFM application needs. Liquid hydrogen tank pressurization tests carried out at the MSFC test stand 300 facilities provide reliable validation data for this purpose. These tests were modeled using the Loci-Stream solver with a newly implemented two-phase sharp interface treatment. We show that our modeling approach and CFD solver predict the autogenous pressurization phenomena satisfactorily, and document challenging aspects of modeling this problem.

CFM↗

NASA NTRSDate not supplied

Validation of Two Phase Flow Modeling Techniques in Loci-Stream using Axial Jet Pressure Control and Autogenous Pressurization Experiment

Autogenous pressurization of cryogenic propellant tanks eliminates the need to have an additional pressurant tank on the space vehicle, which is highly advantageous due to reduced vehicle mass and design complexity. Autogenous pressurization therefore is one of the key technologies for deep space exploration and long-term space missions. The complex interaction of thermal gradients, turbulence and phase change near the interface make the problem a challenging one to model. Nodal analysis tools and reduced order models are unable to capture the necessary physics. 3-D CFD analyses are necessary to fully characterize autogenous pressurization. CFD analyses pose their own difficulties. The requisite CFD tool to tackle this problem need to be modular with the ability to incorporate various physics models, efficient, and computationally scalable for simulating flight size tanks. NASA MSFC's Loci-Stream CFD tool along with the VOF module is a great candidate to fit this mold. We demonstrate our modeling approach and validation of Loci-Stream for predicting autogenous pressurization of a flight scale propellant tank in order for the solver to serve as a reliable design and analysis tool for NASA's CFM application needs. Liquid hydrogen tank pressurization tests carried out at the MSFC test stand 300 facilities provide reliable validation data for this purpose. These tests were modeled using the Loci-Stream solver with a newly implemented two-phase sharp interface treatment. We show that our modeling approach and CFD solver predict the autogenous pressurization phenomena satisfactorily, and document challenging aspects of modeling this problem.

cryogenic fluid management↗

NASA NTRS2004

The Effect of Aerosols and Clouds on the Retrieval of Infrared Sea Surface Temperatures

Comparisons are performed between spatially averaged sea surface temperatures (ASST2) as derived from the second Along-Track Scanning Radiometer (ATSR-2) on board the second European Remote Sensing Satellite (ERS-2) and the NOAA-NASA Advanced Very High Resolution Radiometer (AVHRR) Oceans Pathfinder dataset (MPFSST). Difference maps, MPFSST 2 ASST2, along with the application of a simple statistical regression model to aerosol and cloud data from the Total Ozone Mapping Spectrometer ( TOMS), are used to examine the impact of possible aerosol and cloud contamination. Differences varied regionally, but the largest biases were seen off western Africa. Nighttime and daytime differences off western Africa were reduced from -0.5degrees to -0.2degreesC and from -0.1degrees to 0degreesC, respectively. Significant cloud flagging, based on the model, occurred in the Indian Ocean, the equatorial Pacific, and in the vicinity of the Gulf Stream. Comparisons of the MPFSST and the ASST2 with in situ data from the 2002 version of the World Oceanic Database (WOD02) off western Africa show larger mean differences for the MPFSST. The smallest mean differences occurred for nighttime ASST2 - WOD02 with a value of 0.0degrees +/- 0.4degreesC.

clouds↗

NASA NTRS1974

Development of a remote sensing technique to study the hydrology of earth stock tanks on a semiarid watershed

The stock tanks considered are relatively small earthen reservoirs, built in tributary stream channels and drainageways. A remote sensing technique is developed for obtaining quantitative data on water levels and water losses from stock tanks. Details of the used approaches are discussed along with some difficulties which would have to be overcome in order to determine the effects of the stock tanks on stream flow.

Cluff, C. B.↗

NASA NTRS1991

The meandering Gulf Stream as seen by the Geosat altimeter - Surface transport, position, and velocity variance from 73 deg to 46 deg W

Results are presented of an analysis of the surface geostrophic velocity field for the Gulf Stream region for the position, structure, and surface transport of the Gulf Stream for 2.5 yr of the Geosat altimeter Exact Repeat Mission. Synthetic data using a Gaussian velocity profile were generated and fit to the sea surface residual heights to create a synthetic mean sea surface height field and profiles of absolute geostrophic currents. An analysis of the model parameters and the actual geostrophic velocity profiles revealed two different flow regimes for the Gulf Stream connected by a narrow transition region coincident with the New England Seamount Chain. The upstream region was found to exhibit relatively straight Gulf Stream paths, long Eulerian time scales, and eastward propagating meanders. The downstream region had more large meanders, no consistent propagation direction, and shorter Eulerian time scales. A 25-percent reduction in surface transport occurred in the transition region, with a corresponding reduction in current speed and no change in Gulf Stream width.

Kelly, Kathryn A.↗

NASA NTRS1972

Recirculation patterns in the initial region of coaxial jets.

This experimental study is concerned with the mixing in the initial region of turbulent coaxial streams. The investigation is limited to the low-speed incompressible case with the inner stream of lower velocity than the outer stream. Velocity ratios ranged from infinity to one. The inner to outer stream density ratio was either 4 or 1. Experimental measurements were made with a hot-wire anemometer system, static pressure probes, and shadowgraphy. The data show that a backflow region is formed in this particular apparatus at outer to inner stream velocity ratio of 13 for the homogeneous case and at outer to inner stream velocity ratio of 26 for the heterogeneous case. For higher velocity ratio, a circulating toroidal vortex is established which enhances mixing between the inner and outer streams. This vortex pattern exhibits similarity of velocity with velocity ratio variations.

Rozenman, T.↗

NASA NTRS1993

Comparison of reacting and non-reacting shear layers at a high subsonic Mach number

The flow field in a hydrogen-fueled planar reacting shear layer was measured with an LDV system and is compared with a similar air to air case without combustion. Measurements were made with a speed ratio of 0.34 with the highspeed stream at Mach 0.71. They show that the shear layer with reaction grows faster than one without, and both cases are within the range of data scatter presented by the established database. The coupling between the streamwise and the cross-stream turbulence components inside the shear layer is slow, and reaction only increased it slightly. However, a more organized pattern of the Reynolds stress is present in the reacting shear layer, possibly as a result of larger scale structure formation in the layer associated with heat release.

Chang, C. T.↗