Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “rig”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Influence of design parameters on occurence of oil whirl

Oil whirl instability is a serious problem in oil lubricated journal bearings. The phenomenon is characterized by a subsynchronous vibration of the journal within the bush and is particularly apparent in turbogenerators, aeroengines and electric motors. A review is presented of previous papers on the subject of oil whirl, and a simple theory is described which was used to aid the design of an oil whirl test rig. Predictions of the onset of oil whirl made by the theory presented were found to agree with those of previous researchers. They showed that increasing the shaft flexibility, or the lubricant viscosity, and decreasing the bearing radial clearance tended to reduce the oil whirl onset speed thus making the system more unstable.

Ogrodnik, P. J.↗
NASA NTRS1985

Whirl/whip demonstration

Fluid flow in bearings and seals, set in motion by shaft rotation, generates dynamic forces which may result in a well recognized instability known as whirl and whip. These are lateral, forward precessional, self excited, subsynchronous vibrations in which the amplitude may vary from very small to nearly the limit of the bearing or seal clearances. Oil whirl in lubricated bearings, in particular, typically occurs at somewhat less than half rotative speed. As the rotative speed increases, the frequency relationship remains constant until the whirl frequency approaches the first balance resonance. Now the whirl is smoothly replaced by whip at a nearly constant frequency asymptotically approaching first balance resonance, independent of increasing rotative speed. Changes in bearing/seal radial loading can permit, prevent, or eliminate this instability. The oil whirl/whip rig demonstrates the effects of fluid dynamic forces generated by the rotating shaft. At low rotative speeds, this produces changes of the journal static equilibrium position within the bearing. The demonstrator shows the relationship between any load direction and the average journal equilibrium position. At higher rotative speeds, the instability threshold is observed as a function of unidirectional radial load, unbalance, and rotor configuration.

Grissom, R.↗
NASA NTRS1985

Partial rotor-to-stator rub demonstration

A rotor radial rub typically occurs in seals or at a blade tip or shroud when there is insufficient clearance, high vibration, or the shaft equilibrium position has been displaced to effectively limit the clearance (eccentricity). There are two extreme cases of radial rubs: full annular rub, when the rotor maintains continuous contact with the seal, etc.; and a partial rub, when the contact occurs during a fraction of the precession period. They both involve similar physical phenomena such as friction and modification of stiffness. In partial rubs with consecutive impacts, a significant average value of radial force is generated. This results in shaft average displacement in the direction opposite the rub location. The rotor rig demonstrates the characteristics of a partial lateral rub of varying severity and location. These characteristics include: (1) subharmonic components as a function of rotative speed/first balance resonance ratio and radial force; (2) higher harmonic content as a function of severity; (3) increased average rotor stiffness resulting in increased first balance resonance speed; and (4) change in overall orbital pattern as a sum of the unbalance response (1x) and subharmonic response (1nx).

Grissom, R.↗
NASA NTRS1985

Shaft mode shape demonstration

The dynamic response of a rotating machine is directly influenced by its geometric configuration and all aspects of the rotor construction. These determine two significant parameters, mass distribution and stiffness, which yield a spectrum of natural frequencies and mode shapes. The mode shapes can be presented as snapshots of the characteristic amplitude/phase reponse patterns of the shaft, due to the major forcing function of unbalance, at different rotative speeds. To demonstrate the three shaft mode shapes of the rotor rig using the Shaft Mode Demonstrator and oscilloscopes. The synchronous (1X) amplitude and phase of the rotor vibration in the vertical direction from several points along the shaft is displayed on corresponding points of the demonstrator. Unfiltered vibration from vertical and horizontal probe pairs is displayed on the oscilloscopes in orbit format for a dynamic presentation of the mode shape.

Grissom, R.↗
NASA NTRS1986

Influence of third-degree geometric nonlinearities on the vibration and stability of pretwisted, preconed, rotating blades

The governing coupled flapwise bending, edgewise bending, and torsional equations are derived including third-degree geometric nonlinear elastic terms by making use of the geometric nonlinear theory of elasticity in which the elongations and shears are negligible compared to unity. These equations are specialized for blades of doubly symmetric cross section with linear variation of pretwist over the blade length. The nonlinear steady state equations and the linearized perturbation equations are solved by using the Galerkin method, and by utilizing the nonrotating normal modes for the shape functions. Parametric results obtained for various cases of rotating blades from the present theoretical formulation are compared to those produced from the finite element code MSC/NASTRAN, and also to those produced from an in-house experimental test rig. It is shown that the spurious instabilities, observed for thin, rotating blades when second degree geometric nonlinearities are used, can be eliminated by including the third-degree elastic nonlinear terms. Furthermore, inclusion of third degree terms improves the correlation between the theory and experiment.

Subrahmanyam, K. B.↗
NASA NTRS1986

Structural dynamic measurement practices for turbomachinery at the NASA Lewis Research Center

Methods developed for measuring blade and rotor-shaft system response include optical systems, transient instruments, and special digital data processing equipment. Optical methods offer some distinct benefits for blade vibration measurement. Transient and steady state measurements of the response of rotor-shaft systems strongly affect analytical methods development. Digital computing systems allow processing of large volumes of high speed data from rotating blade sets. Also, digital systems develop useful vibration response signatures from randomly excited systems. Research facilities include the spin rig facility and the transient rotor response lab.

Kiraly, L. J.↗
NASA NTRS1985

Traction forces at solid-lubricated rolling/sliding contacts

A single-element traction rig was used to measure the traction forces at a solid-lubricated contact of a ball against a flat disk at room temperature under combine rolling and sliding. The load and speed conditions were selected to match those anticipated for bearing applications in adiabatic diesel engines. Traction vs slide/roll ratio curves were similar to those for liquid lubricants but the traction forces were an order of magnitude higher. The test data were used to derive equations to predict traction force as a function of contact stress and rolling speed. The data showed that the magnitude of traction forces were almost the same for all the lubricants tested. The lubricants, should, therefore, be selected on the basis of their ability to limit the wear of contact surfaces.

Aggarwal, B. B.↗
NASA NTRS1985

DEAN - A program for Dynamic Engine ANalysis

The Dynamic Engine Analysis Program, DEAN, is a FORTRAN code implemented on the IBM/370 mainframe at NASA Lewis Research Center for digital simulation of turbofan engine dynamics. DEAN is an interactive program which allows the user to simulate engine subsystems as well as full engine systems with relative ease. The nonlinear first order ordinary differential equations which define the engine model may be solved by one of four integration schemes, a second order Runge-Kutta, a fourth order Runge-Kutta, an Adams Predictor-Corrector, or Gear's method for still systems. The numerical data generated by the model equations are displayed a specified intervals between which the user may choose to modify various parameters affecting the model equations and transient execution. Following the transient run, versatile graphics capabilities allow close examination of the data. DEAN's modeling procedure and capabilities are demonstrated by generating a model of simple compressor rig.

Sadler, G. G.↗
NASA NTRS1986

Liquid droplet radiator program at the NASA Lewis Research Center

The NASA Lewis Research Center and the Air Force Rocket Propulsion Laboratory (AFRPL) are jointly engaged in a program for technical assessment of the Liquid Droplet Radiator (LDR) concept as an advanced high performance heat ejection component for future space missions. NASA Lewis has responsibility for the technology needed for the droplet generator, for working fluid qualification, and for investigating the physics of droplets in space; NASA Lewis is also conducting systems/mission analyses for potential LDR applications with candidate space power systems. For the droplet generator technology task, both micro-orifice fabrication techniques and droplet stream formation processes have been experimentally investigated. High quality micro-orifices (to 50 micron diameter) are routinely fabricated with automated equipment. Droplet formation studies have established operating boundaries for the generation of controlled and uniform droplet streams. A test rig is currently being installed for the experimental verification, under simulated space conditions, of droplet radiation heat transfer performance analyses and the determination of the effect radiative emissivity of multiple droplet streams. Initial testing has begun in the NASA Lewis Zero-Gravity Facility for investigating droplet stream behavior in microgravity conditions. This includes the effect of orifice wetting on jet dynamics and droplet formation. Results for both Brayton and Stirling power cycles have identified favorable mass and size comparisons of the LDR with conventional radiator concepts.

Presler, A. F.↗
NASA NTRS1987

Wind-Tunnel Capability at Ames Research Center

Report describes $700 million wind-tunnel complex at Ames Research Center, including auxiliary support systems, test instrumentation, and special test rigs. Planned near-term facility improvement aimed at providing new test capabilities and increased productivity, as well as some potential longer-term improvements, also discussed. Aerodynamic test facilities range from subsonic wind tunnels to highenthalpy arc jets.

Snyder, C. T.↗
NASA NTRS1986

New short-time alignment technique for 70-meter antenna surface panels

With severely limited field modification time for upgrading the 64-m antenna to 70-m diameter, a new shorter time method for aligning the surface panels of the main reflector was needed. For each target on the surface panel, both distance (or range) and elevation angle measurements are made. A new technique for setting the surface panels at zenith look has been devised. This article describes the software required to convert the computed target distortions obtained from the JPL-IDEAS structural analysis computer program (defining the gravity load change from a 45-deg elevation angle to zenith look) into the theodolite reading at zenith look. The technique results in a perfectly shaped reflector at the 45-deg rigging elevation, with acceptable surface error tolerance.

Katow, M. S.↗
NASA NTRS1986

Advanced Gas Turbine (AGT) Technology Project

Engine testing, ceramic component fabrication and evaluation, component performance rig testing, and analytical studies comprised AGT 100 activities during the 1985 year. Ten experimental assemblies (builds) were evaluated using two engines. Accrued operating time was 120 hr of burning and 170 hr total, bringing cumulative total operating time to 395 hr, all devoid of major failures. Tests identified the generator seals as the primary working fluid leakage sources. Power transfer clutch operation was demonstrated. An alpha SiC gasifier rotor engine test resulted in blade tip failures. Recurring case vibration and shaft whip have limited gasifier shaft speeds to 84%. Ceramic components successfully engine tested now include the SiC scroll assembly, Si3N3 turbine rotor, combustor assembly, regenerator disk bulkhead, turbine vanes, piston rings, and couplings. A compressor shroud design change to reduce heat recirculation back to the inlet was executed. Ceramic components activity continues to focus on the development of state-of-the-art material strength characteristics in full-scale engine hardware. Fiber reinforced glass-ceramic composite turbine (inner) backplates were fabricated by Corning Glass Works. The BMAS/III material performed well in engine testing. Backplates of MAS material have not been engine tested.

Source record↗
NASA NTRS1986

A low-cost optical data acquisition system for vibration measurement

A low cost optical data acquisition system was designed to measure deflection of vibrating rotor blade tips. The basic principle of the new design is to record raw data, which is a set of blade arrival times, in memory and to perform all processing by software following a run. This approach yields a simple and inexpensive system with the least possible hardware. Functional elements of the system were breadboarded and operated satisfactorily during rotor simulations on the bench, and during a data collection run with a two-bladed rotor in the Lewis Research Center Spin Rig. Software was written to demonstrate the sorting and processing of data stored in the system control computer, after retrieval from the data acquisition system. The demonstration produced an accurate graphical display of deflection versus time.

Posta, S. J.↗
NASA NTRS1986

Mars surface science requirements and plan

The requirements for obtaining geological, geochemical, geophysical, and meteorological data on the surface of Mars associated with manned landings were analyzed. Specific instruments were identified and their mass and power requirements estimated. A total of 1 to 5 metric tons, not including masses of drill rigs and surface vehicles, will need to be landed. Power associated only with the scientific instruments is estimated to be 1 to 2 kWe. Requirements for surface rover vehicles were defined and typical exploration traverses during which instruments will be positioned and rock and subsurface core samples obtained were suggested.

Blacic, J. D.↗
NASA NTRS1986

Oxide-dispersion-strengthened turbine blades, volume 1

The objective of Project 4 was to develop a high-temperature, uncooled gas turbine blade using MA6000 alloy. The program objectives were achieved. Production scale up of the MA6000 alloy was achieved with a fair degree of tolerance to nonoptimum processing. The blade manufacturing process was also optimized. The mechanical, environmental, and physical property evaluations of MA6000 were conducted. The ultimate tensile strength, to about 704 C (130 F), is higher than DS MAR-M 247 but with a corresponding lower tensile elongation. Also, above 982 C (180 F) MA6000 tensile strength does not decrease as rapidly as MAR-M 247 because the ODS mechanism still remains active. Based on oxidation resistance and diffusional stability considerations, NiCrAlY coatings are recommended. CoCrAly coating should be applied on top of a thin NiCrAlY coating. Vibration tests, whirlpit tests, and a high-rotor-rig test were conducted to ensure successful completion of the engine test of the MA6000 TFE731 high pressure turbine blades. The results of these tests were acceptable. In production quantities, the cost of the Project 4 MA6000 blade is estimated to be about twice that of a cast DS MAR-M 247 blade.

Millan, P. P., Jr.↗
NASA NTRS1987

Electron stimulated desorption of atomic oxygen from silver

The electron stimulated desorption (ESD) of neutral oxygen atoms from polycrystalline silver and of oxygen ions from Ag(110) has been studied. Polycrystalline Ag charged with (16)O2 and (18)O2 and bombarded by low-energy electrons (approx 100 eV) under ultrahigh vacuum (UHV) conditions emitted O atom flux levels of 1 x 10 to the 12th power/sq cm/s at a Ag temperature of 300 C. The flux was detected with a quadrupole mass spectrometer operating in the appearance potential mode. The neutral cross section at about 100 C was determined to be 7 x 10 to the -19 sq cm. Ancillary experiments conducted in a UHV chamber equipped with a cylindrical mirror analyzer and rigged for ion energy distribution and ion angular distribution were used to study O ions desorbed from Ag(110). Two primary O(+) energies of 2.4 and 5.4 eV were detected from the Ag(110) after having been dosed with 2500 L of (16)O2. It also appears that in both experiments there was strong evidence for directionality of the emitted flux. The results of this study serve as a proof of concept for the development of a laboratory atomic oxygen beam generator that simulates the gas flux environment experienced by orbiting vehicles.

Outlaw, R. A.↗
NASA NTRS1986

Cryogenic gear technology for an orbital transfer vehicle engine and tester design

Technology available for gears used in advanced Orbital Transfer Vehicle rocket engines and the design of a cryogenic adapted tester used for evaluating advanced gears are presented. The only high-speed, unlubricated gears currently in cryogenic service are used in the RL10 rocket engine turbomachinery. Advanced rocket engine gear systems experience operational load conditions and rotational speed that are beyond current experience levels. The work under this task consisted of a technology assessment and requirements definition followed by design of a self-contained portable cryogenic adapted gear test rig system.

Calandra, M.↗
NASA NTRS1987

Hot corrosion attack and strength degradation of SiC and Si(sub)3N(sub)4

Thin films of Na2SO4 and Na2CO3 molten salt deposits were used to corrode sintered SiC and Si3N4 at 1000 C. The resulting attack produced pitting and grain boundary etching resulting in strength decreases ranging from 15 to 50 percent. Corrosion pits were the predominant sources of fracture. The degree of strength decrease was found to be roughly correlated with the depth of the pit, as predicted from fracture toughness considerations. Gas evolution and bubble formation were key aspects of pit formation. Many of the observations of furnace exposures held true in a more realistic burner rig test.

Smialek, James L.↗