Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Catalytic and electrocatalytic performance of Sr(Ti 0.3 Fe 0.7 Ru 0.07 )O 3-δ for applications in solid oxide fuel cells supplied with ethanol steam reforming mixtures

We discuss how direct utilization of alcohols in Solid Oxide Fuel Cells (SOFCs) can improve the conversion efficiency by using excess heat for internal reforming and simplify the system balance of plant. Thanks to their scarce carbon- formation tendency, perovskite oxide anodes are promising alternatives to Ni-based cermets. Here we show that Sr(Ti 0.3 Fe 0.7 Ru 0.07 )O 3-δ (STF-Ru) exsolution anodes provide both catalytic reforming activity and electro- chemical activity with steam/ethanol (S/E) mixtures at 3:1 and 2:1 M ratio between 700 and 800 °C. Electrolyte- supported scandia stabilized zirconia SOFCs with STF-Ru anodes and Sr 0.95 Ti 0.3 Fe 0.7 O 3-δ (STF) cathodes are reasonably stable in the 3:1 S/E mixture over 20 h at 800 °C, with maximum power density of 195 mW/cm 2 and 140 mW/cm 2 at 0.7 V. Deactivation instead occurs with the 2:1 S/E mixture. Comparatively, cells with Ni-YSZ anodes rapidly coke and fail under the same conditions. Ethanol steam reforming experiments in a fixed bed powder reactor reveal that, above 650 °C, gas phase reactions convert ethanol to CO, hydrogen, acetaldehyde and ethylene, while STF-Ru catalyzes steam reforming. Thermogravimetric and Raman characterizations show that a moderate amount of carbon is deposited on the STF-Ru surface, which is more amorphous than the disruptive carbon which degrades Ni-YSZ.

09 BIOMASS FUELS↗
DOE OSTI2022

Optimization of metal-supported solid oxide fuel cells with a focus on mass transport

Performance of symmetric-architecture metal-supported solid oxide fuel cells was improved significantly by optimizing the catalyst infiltration process and metal support structure. Optimization of component structure and processing parameters was performed during tape-casting and fabrication of button cells. Mass transport of oxygen in the metal support was identified as a major limitation. To overcome this limitation, pore former loading and thickness of the metal support (130–250 μm) were optimized. The catalyst infiltration process was also improved by studying the impact of firing temperature (400 °C–900 °C) and infiltration cycle numbers (1–15). The maximum power density of the optimized cell was 0.9 W cm –2 at 700°C using hydrogen as a fuel, a three-fold increase over the baseline cell performance. The degradation rate of optimized cells at 550 °C, 600 °C, and 700 °C was 2%, 4.5%, and 5.5% per 100 h, respectively. Here, the phenomena of mass transport, catalyst coarsening, and chromium poisoning on the catalyst were analyzed by electrochemical impedance spectroscopy and scanning electron microscopy.

13 HYDRO ENERGY↗
DOE OSTI2024

The battery failure databank: Insights from an open-access database of thermal runaway behaviors of Li-ion cells and a resource for benchmarking risks

The thermal response of Li-ion cells can greatly vary for identical cell designs tested under identical conditions, the distribution of which is costly to fully characterize experimentally. The open-source Battery Failure Databank presented here contains robust, high-quality data from hundreds of abuse tests spanning numerous commercial cell designs and testing conditions. Data was gathered using a fractional thermal runaway calorimeter and contains the fractional breakdown of heat and mass that was ejected, as well as high-speed synchrotron radiography of the internal dynamic response of cells during thermal runaway. The distribution of thermal output, mass ejection, and internal response of commercial cells are compared for different abuse-test conditions, which when normalized on a per amp-hour basis show a strong positive correlation between heat output from cells, the fraction of mass ejected from the cells, their energy- and power-density. Ejected mass was shown to contain 10x more heat per gram than non-ejected mass. The causes of 'outlier' thermal and ejection responses i.e., extreme cases, are elucidated by high-speed radiography which showed how occurrences such as vent clogging can create more hazardous conditions. High-speed radiography also demonstrated how the time-resolved interplay of thermal runaway propagation and mass ejection influences the total heat generated.

25 ENERGY STORAGE↗
DOE OSTI2025

Bipolar plate flow channel designs for vanadium redox flow battery: a review

Vanadium redox flow battery is one of the preferred systems for grid scale energy storage due to long service life (>20000 cycles), higher efficiency (>85 %), deep discharge capability (>95 % DoD), and inherent scalability and safety. Among system components, flow field is most critical as it governs electrolyte distribution, mass transport and hydraulic performance. Here, this review examines emerging flow channel geometries, highlighting the impact of channel width (0.66 to 1.5 mm), depth (1 to 1.5 mm) and land width (0.5 to 1.5 mm) can reduce pressure drop to <10 kPa while enabling power densities above 600 mW.cm -2 . A key finding is that low channel width to depth ratio (<1) enhances voltage and energy efficiencies by improving under rib convection. The review also provides an overview of progress and perspective in bipolar plate materials, manufacturability, and shunt current mitigation strategies for stack scaling up. Cost analysis emphasizes the influence of flow field designs on the levelized cost of storage and pathways towards the US DOE's $\$$0.05 per kWh energy generation cost target. In addition, opportunities for AI/ML/DT tools assisted design and data driven optimization strategies are also outlined to accelerate next generation flow field development.

Efficiency optimization↗
DOE OSTI2023

A reversible perovskite air electrode for active and durable oxygen reduction and evolution reactions via the A-site entropy engineering

The performance of reversible solid oxide electrochemical cells (R-SOECs) is largely hindered by the insufficient electroactivity and poor durability of the bifunctional air electrodes, where the oxygen reduction and evolution reactions (ORR and OER) occur. Here, we report our findings in boosting the electrochemical activity and durability of an air electrode with Pr 0.2 Ba 0.2 Sr 0.2 La 0.2 Ca 0.2 CoO 3-δ (PBSLCC) via an A-site entropy engineering. The PBSLCC electrode shows enhanced oxygen reaction activity and excellent durability compared to binary and ternary double perovskites (PrBaCo 2 O 5+δ and Pr 0.8 Ba 0.8 Ca 0.4 Co 2 O 5+δ , respectively). A low and nearly unchanged area-specific resistance of 0.042Ωcm 2 is achieved at 750 °C during the 225-h stability test. La 0.9 Sr 0.1 Ga 0.8 Mg 0.2 O 3-δ electrolyte-supported cells with the PBSLCC air electrode show remarkable performance at 800 °C, demonstrating a peak power density of 1.2Wcm -2 in the fuel cell mode, and a current density of -1.1 Acm -2 at 1.3 V in the electrolysis mode while maintaining the excellent cycling durability of 228 h at ±0.5 Acm -2 under humidified H 2 (10% H 2 O). A bulk oxygen p-band center model is applied to verify that tailoring of the A-site entropy strongly influences the surface exchange coefficients (k* chem ), leading to higher oxygen reaction activity of PBSLCC than the binary and ternary perovskites. Finally, this study opens a new class of high-entropy perovskites for the rational design of air electrodes for R-SOECs with high activity and durability.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

An efficient construction of nano-interfaces for excellent coking tolerance of cermet anodes

Solid oxide fuel cells (SOFCs) are promising energy conversion devices for the effective and convenient utilization of hydrocarbons (for example, methane) to electricity. However, the development of direct methane SOFCs is primarily hindered by the poor coking tolerance of the state-of-the-art Ni-based cermet anodes. Herein, we efficiently construct nano-interfaces in the anode by infiltrating a Ni 0.6 Y 0.064 Zr 0.336 O 2-δ (NYZ) catalyst onto the traditional Ni-based cermet anode to effectively enhance the coking tolerance. After being reduced in H 2 , Ni and Y 0.16 Zr 0.84 O 2-δ (YSZ) nanoparticles (NPs) are in situ formed on the surface of the Ni-YSZ substrate. The roughened anode demonstrates significantly improved fuel oxidation activity and coking tolerance, due likely to the formation of nano-interfaces. Specifically, when applied in the Ni-YSZ-based anode-supported SOFCs, a high peak power density of 1.785 W cm –2 and a stable operation of ~ 240 h with no observable degradation is achieved at 750 °C in nearly dry methane (3% H 2 O). Finally, a density functional theory study suggests that the excellent coking tolerance is attributed to the formation of OH species on Ni/YSZ nano-interfaces, which would further interact with intermediate carbon species to generate COH intermediates.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Improving the bulk gas transport of Fe-N-C platinum group metal-free nanofiber electrodes via electrospinning for fuel cell applications

To overcome transport limitations associated with thicker platinum group metal-free (PGM-free) electrodes, it's essential to investigate and tailor alternative electrode architectures to maximize the bulk electrode transport properties, whilst not significantly impeding electrocatalyst active site accessibility and electrode proton resistance. In this work, PGM-free nanofiber electrode mats, prepared by electrospinning a mixture of pyrolyzed Fe-N-C catalyst, Nafion ionomer and a carrier polymer Poly Acrylic acid (PAA), were compared to traditionally prepared electrodes. The morphological properties and elemental distribution of the fabricated nanofiber electrodes showed that the exterior surface of the PGM-free nanofibers was conformally covered with a thin ionomer film. Electrochemical diagnostics performed utilizing cyclic voltammetry, electrochemical impedance spectroscopy (EIS) and H 2 -limiting current measurements, revealed an increase in electric double layer capacitance, reduction in electrode proton transport and a significant improvement in bulk-electrode gas transport properties for the nanofiber electrodes, supporting the observed performance increase from electrochemical polarization data obtained in H 2 -O 2 /Air fuel cells. At 100% RH in H2/Air, the power density of the nanofiber electrodes increased ca. 50% vs. the traditionally prepared electrodes (ca. 260 vs 175 mW cm -2 ), which was attributed to a less tortuous molecular diffusion pathway and an associated reduction in the pressure dependent and independent gas transport resistances in the nanofiber electrodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Durable hybrid electrocatalysts for proton exchange membrane fuel cells

The low durability of carbon-based non-precious metal electrocatalysts hinders their practical applications in proton exchange membrane fuel cells (PEMFCs). In this study, we rationally design a hybrid Pt-Fe-N-C electrocatalyst with unprecedented durability. It consists of abundant Pt and Fe single atoms homogeneously dispersed on the nitrogen-doped carbon support and a small amount of Pt-Fe alloy nanoparticles. A PEMFC with Pt-Fe-N-C as the cathode shows a larger peak power density (0.75 W cm -2 ) than that with Fe-N-C as the cathode (0.50 W cm -2 ). The remarkable durability of Pt-Fe-N-C is reflected from no noticeable drop in the half-wave potential after 70000 potential cycles between 0.6 and 1.0 V in the liquid cell, and 80% current retention after 85 h of potential hold at 0.4 V in the fuel cell. This work demonstrates the feasibility of improving the durability of Fe-N-C material via ultra-low Pt doping and makes non-precious metal electrocatalysts be close to achieving commercial metrics.

25 ENERGY STORAGE↗
DOE OSTI2025

Direct writing of PVBVA/Ti 3 C 2 T x (MXene) triboelectric nanogenerators for energy harvesting and sensing applications

Triboelectric nanogenerators (TENGs) have gained recognition for their potential to convert mechanical energy into electrical energy, making them attractive for applications in healthcare, robotics, and human-device interfaces. However, many TENG devices rely on fluorinated polymers for high charge generation and involve complex fabrication processes, which limit their practicality and environmental sustainability. Here, we developed an eco-friendly composite of poly (vinyl butyral-co-vinyl alcohol-co-vinyl acetate) (PVBVA) and Ti 3 C 2 T x MXene for extrusion printing onto aluminum foil substrates, enabling the additive manufacturing of TENGs. Experimental results indicate that integrating 5.5 mg mL -1 of MXene (P-MX 5.5) into PVBVA resulted in a power density of 760 mW·m -2 , with simultaneous improvements in open-circuit voltage (129 %) and short-circuit current (250 %), demonstrating enhanced charge transfer efficiency. Beyond aluminum foil-based devices, we further explored the fully printed P-MX 5.5 TENG by utilizing silver ink electrodes, eliminating the need for aluminum foil. This fully printed, flexible TENG was successfully used for real-time human motion sensing, demonstrating its ability to detect activities such as walking, running, knee bending, and jumping. Collectively, our additively manufactured and sustainable PVBVA-MXene TENG composites, including both aluminum-based and fully printed versions, show promise for future energy harvesters, sensors, wearable electronics, healthcare, and robotic applications.

Additive manufacturing↗
DOE OSTI2020

Durability test of a flowing-water target for isotope harvesting

A high intensity proton irradiation was performed with the flowing-water isotope harvesting target at the University of Wisconsin-Madison Cyclotron Laboratory to measure the rate of degradation of the target shell during irradiation conditions. The beam reached an intensity of 34 µA by the end of the irradiation and covered an area of 0.7 cm 2 on the target. Radiolysis products, such as H 2 O 2 , H 2 , and O 2 , were measured in the bulk water of the system and found to be present at much lower levels than predicted by literature escape yields. Radionuclides formed in the target shell were measured in the system water as a radiotracer for target degradation. Using a simple, beam intensity dependent model, a corrosion rate of 1.5E-6 μm/(μA*s) was found to match the measured radiotracer activities at various points in the irradiation. Furthermore, this rate was used to extrapolate the lifetime of future isotope harvesting targets at the NSCL and FRIB, using the areal power density of different ion beams to scale the corrosion rate.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Single-phase, natural circulation annular flow measurements for cartridge loop irradiation experiments

The nuclear industry is increasingly considering cartridge-style experiments for irradiation testing of advanced reactor fuels and materials under flowing conditions. Cartridge loops do not require the extensive support infrastructure that are necessary for external flow loops and minimize the possibility of coolant solidification over the long distance from the reactor to the external facilities. However, there is a general lack of quality flow data for internally heated fluids in an annular configuration representative of a cartridge-type irradiation experiment, particularly one with natural circulation. To address this data need, a series of experiments was conducted to measure the natural circulation flow rates of pressurized water in a sealed, internally heated vessel with annular flow conditions that represent a molten salt or sodium cartridge loop. Temperatures and flow rates were measured under steady-state and transient conditions. Here, this paper describes the facility, methods, and results of the experiments, including the determination of nondimensional parameters. A simple 1D model of the natural convection flow rates agrees well with the experimental results. Applying this model to simulate a liquid salt cartridge experiment predicts that natural circulation flow might be able to provide liquid salt Reynolds numbers similar to those of some molten salt reactor concepts at relevant power densities.

42 ENGINEERING↗
DOE OSTI2024

RELAP5-3D validation studies based on the High Temperature Test facility

In the spring and summer of 2019, experiments were conducted at the High Temperature Test Facility (HTTF) that form the basis of an upcoming high-temperature gas-cooled reactor (HTGR) thermal hydraulics (T/H) benchmark. HTTF is an integral effects test facility for HTGR T/H modeling validation. This paper presents RELAP5-3D models of two of those experiments: PG-27, a pressurized conduction cooldown (PCC); and PG-29, a depressurized conduction cooldown (DCC). These models used the RELAP5-3D model of HTTF originally developed by Paul Bayless as a starting point. The sensitivity analysis and uncertainty quantification code, RAVEN was used to perform calibration studies for the steady-state portion of PG-27. Here we developed four PG-27 calibrations based on steady-state conditions. These calibrations all used an effective thermal conductivity equal to 36 % of the measured thermal conductivity, but they differed with respect to the frictional pressure drops and radial conduction models. These models all captured the trends in steady-state temperature distributions and transient temperature behavior well. All four calibrations show room for improvement in predicting the transient temperature rise. The smallest error in temperature rise during the transient was a 21 % underprediction, and the largest was a 48 % underprediction. The errors in transient temperature rise are largely a result of a mismatch in power density between the RELAP5-3D model and the experiment due to the location of active heater rods along the boundary between heat structures in the model. The best of these calibrations was applied to PG-29 to model the DCC. Once again, temperatures during the transient were underpredicted but trends in temperature were captured. The RELAP5-3D model captured trends in the data but could not reproduce measured temperatures exactly. This result is not attributed to deficiencies in the experimental data or to RELAP5–3D itself. Rather, this result likely arises due to the some of the assumptions and decisions made when the RELAP5-3D model was first developed, prior to the execution of HTTF experiments. An agreement in prediction of temperature trends but challenges reproducing HTTF temperatures within measurement uncertainty is consistent with previous analyses of HTTF in the literature. Future RELAP5-3D validation activities centered around HTTF may be able to provide greater insight into the code’s capabilities for HTGR modeling with a more finely nodalized model.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

A methodology for decay heat characterization in molten salt reactors

Accurate decay heat prediction in molten salt reactors (MSRs) faces dual challenges: complex operational uncertainties and the need for interpretable models compatible with engineering workflows. This work presents a hybrid machine learning and segmented polynomial methodology that addresses both requirements through three key innovations. First, a modular data architecture encodes MSR-specific operational parameters (power density: 1-100 W cm -3 , humidity: 0-0.1 wt %, air ingress: 0-0.1 mol %) with uncertainty-aware temporal discretization spanning 15 orders of magnitude. Second, region-optimized machine learning models achieve 92.3 % root mean square error (RMSE) reduction over conventional polynomials while maintaining physical interpretability through automated piecewise equation generation. Third, dual front-end interfaces accelerate safety analyses — a Jupyter environment enables researchers to explore 10,000+ parameter combinations via interactive widgets, while a Streamlit web application reduces design iteration cycles through production-grade visualization tools. Operational deployment demonstrates prediction times of only a couple hundred milliseconds for 10 4 years decay profiles, enabling real-time optimization of spent fuel container designs.

42 - ENGINEERING↗
DOE OSTI2026

Computational modeling of graphite degradation in molten salt reactors: Role of infiltration

Molten salt reactors (MSRs) often employ graphite as a moderator and reflector. An important challenge for deploying graphite in these reactors is that, due to limited experimental data, our understanding of graphite’s structural integrity in molten salt environments remains incomplete. Here, this study addresses heat generation from fuel-bearing salt that has infiltrated open pores in the graphite, driven primarily by pressure differentials. This is one of multiple identified physical and chemical mechanisms through which molten salt could potentially degrade graphite. Thermally driven stresses are quantified using the Molten-Salt Reactor Experiment (MSRE) graphite moderator elements as a case study. Finite element simulations predict stress distributions at varying infiltration levels, indicating that thermal stresses increase with higher infiltration. Rare-event simulations using the parallel subset simulation framework identify the combinations and corresponding ranges of input parameters that lead to stresses above a specified threshold. In particular, combinations involving high infiltration amounts, high power density, and low thermal conductivity tend to induce the highest stresses. Under the inputs and assumptions considered in this work, the magnitudes of the thermally driven stresses are quite low, with a very low likelihood of causing failure due to exceeding the graphite’s tensile strength. Additionally, rare-event simulations were performed for two more scenarios: a scaled-up moderator geometry and a localized hotspot in the original geometry. Both cases resulted in increased susceptibility to failure, though not to a detrimental extent. Furthermore, the combined effects of irradiation and infiltration-induced thermal stresses were evaluated. The results showed that thermal stresses from infiltration were negligible compared to those caused by irradiation. The findings of such a study are inherently component-specific, but the methodology presented here could be used for similar assessments of salt-infiltration effects in other graphite components.

36 - MATERIALS SCIENCE↗
DOE OSTI2026

Transient uncertainty quantification and Global Sensitivity Analysis of the open-source Molten Chloride Reactor Experiment (MCRE) using GP-PCA surrogate models

Uncertainties in the thermophysical properties of molten salts impact both the steady-state and transient behavior of Molten Salt Reactors (MSRs). In this work, we aim to quantify the influence of such uncertainties on the transient operation of the Molten Chloride Reactor Experiment (MCRE), utilizing the open-source specifications provided for this reactor. Seven representative transient scenarios are considered. For each scenario, we evaluate the impact of thermophysical property uncertainties on four key multiphysics model output variables of interest (VoIs): maximum power density, maximum fuel temperature, maximum reflector temperature, and average fuel velocity magnitude. In addition, we perform a Global Sensitivity Analysis (GSA) by computing Sobol’ indices for the uncertain input parameters to determine their contribution to the variability of each VoI. Conducting GSA is computationally intensive due to the large number of required evaluations of the high-fidelity multiphysics model. To mitigate this cost, we develop a surrogate modeling framework that combines Gaussian Process (GP) regression with Principal Component Analysis (PCA), enabling efficient sample generation for the GSA. Our results show that for energy-related VoIs, thermal conductivity is the dominant contributor to uncertainty. In contrast, for flow-related VoIs, density and dynamic viscosity are the primary sources of uncertainty. The specific heat of the fuel salt was found to play a secondary role in the transient analyses.

42 - ENGINEERING↗
DOE OSTI2021

Tidal Stream Energy Resource Characterization in the Salish Sea

Tidal stream energy holds great potential as a renewable energy source in regions of the world where tidal currents are strong and predictable. The tidal stream energy resource of a region is strongly controlled by its tidal wave characteristics, the local bathymetry, and coastal geometric features. The Salish Sea, a large estuary on the Pacific Northwest coast, represents a great tidal stream resource because of its strong tidal currents in many tidal channels. However, the tidal resource in the Salish Sea has not been systematically characterized, primarily because of its large area and complex bathymetry and coastlines. This paper presents a modeling study conducted to characterize the tidal energy resource of the Salish Sea based on a high-resolution three-dimensional tidal hydrodynamic model of the Salish Sea, which was extensively validated using data derived from 10 tidal gauge stations and 132 Acoustic Doppler Current Profiler stations. Model validation results indicated the Salish Sea hydrodynamic model is skillful in simulating tidal wave propagation and velocity distributions in the Salish Sea. Based on model results, a total of 16 tidal channels with strong tidal currents, 9 in the San Juan Islands and Rosario Strait regions and 7 in the Puget Sound, were identified as hotspots for potential tidal energy development. Velocity probability distributions and exceedance curves of cross-channel average velocity magnitudes were calculated at all 16 channels based on the recommendations of the International Electrotechnical Commission Technical Specifications for tidal energy resource characterization. The tidal energy resource at the 16 hotspots was also characterized using power density distributions and kinetic energy fluxes. The ranking of the kinetic energy fluxes suggested that Admiralty Inlet, Rosario Strait, and Middle Channel are the top three hotspot sites in the Salish Sea for tidal stream energy development. The study demonstrated the need for a high-resolution 3-D modeling framework for accurate simulation of tidal currents in large complex estuarine systems, in the context of tidal energy resource characterization.

tidal stream energy, resource characterization, Sa↗