Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “oxygen diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Ability of Particulate Matter Index to describe sooting tendency of various gasoline formulations in a stratified-charge spark-ignition engine

This study investigates the ability of Particulate Matter Index (PMI) to describe the sooting behavior of various gasoline formulations in a stratified-charge (SC) spark-ignition engine. Specifically, the engine was operated at 2000 rpm with an intake pressure of 130 kPa where soot formation is known to primarily occur in the bulk gases. Exhaust soot emissions were measured for nine test fuels at various exhaust gas recirculation levels. A comparison between measured soot levels and PMI shows that PMI is a relatively poor predictor of the sooting tendency of the tested fuels under lean SC combustion. Among the fuels, three fuels, namely the diisobutylene blend, High Olefin, and E30 fuels exhibit measured soot behavior opposite of that predicted by PMI. Optical diagnostics were utilized to further investigate the in-cylinder phenomena for these three fuels. Analysis of natural luminosity and diffused back-illumination extinction imaging suggests that fuel-induced differences in the amount of soot formed are responsible for a majority of the discrepancy in measured versus predicted sooting tendency. Fuel-induced differences in soot oxidation and spray development seem to play minor roles. Because the combustion and air-fuel mixing processes for lean SC combustion are different from conventional stoichiometric operation it is hypothesized that the PMI correlation needs to be modified to account for differences in stoichiometric air-fuel ratio and level of oxygenation between fuels. Furthermore, the role of fuel volatility in PMI possibly needs to be de-emphasized for SC operation with fuel injection into compression-heated gases.

42 ENGINEERING↗
DOE OSTI2021

Hyperstoichiometric Uranium Dioxides: Rapid Synthesis and Irradiation-Induced Structural Changes

Uranium dioxide (UO 2 ), the primary fuel for commercial nuclear reactors, incorporates excess oxygen forming a series of hyperstoichiometric oxides. Thin layers of these oxides, such as UO 2.12 , form readily on the fuel surface and influence its properties, performance, and potentially geologic disposal. This work reports a rapid and straightforward combustion process in uranyl nitrate–glycine–water solutions to prepare UO 2.12 nanomaterials and thin films. We also report on the investigation of the structural changes induced in the material by irradiation. Despite the simple processing aspects, the combustion synthesis of UO 2.12 has a sophisticated chemical mechanism involving several exothermic steps. Raman spectroscopy and single-crystal X-ray diffraction (XRD) measurements reveal the formation of a complex compound containing the uranyl moiety, glycine, H 2 O, and NO 3 – groups in reactive solutions and dried combustion precursors. Combustion diagnostic methods, gas-phase mass spectroscopy, differential scanning calorimetry (DSC), and extracted activation energies from DSC measurements show that the rate-limiting step of the process is the reaction of ammonia with nitrogen oxides formed from the decomposition of glycine and uranyl nitrate, respectively. However, the exothermic decomposition of the complex compound determines the maximum temperature of the process. In situ transmission electron microscopy (TEM) imaging and electron diffraction measurements show that the decomposition of the complex compound directly produces UO 2 . The incorporation of oxygen at the cooling stage of the combustion process is responsible for the formation of UO 2.12 . Spin coating of the solutions and brief annealing at 670 K allow the deposition of uniform films of UO 2.12 with thicknesses up to 300 nm on an aluminum substrate. Irradiation of films with Ar 2+ ions (1.7 MeV energy, a fluence of up to 1 × 10 17 ions/cm 2 ) shows unusual defect-simulated grain growth and enhanced chemical mixing of UO 2.12 with the substrate due to the high uranium ion diffusion in films. As a result, the method described in this work allows the preparation of actinide oxide targets for fundamental nuclear science research and studies associated with stockpile stewardship.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2020

Materials and technological processes for High-Gradient accelerating structures: new results from mechanical tests of an innovative braze-free cavity.

Pure oxygen-free high-conductivity copper is a widely used material for manufacturing accelerating cavities working at room temperature. Several studies attempted to explain limitations associated with the maximum allowed field gradients and the behaviour of vacuum RF breakdown in copper accelerating structures through generation and movement of dislocations under stresses associated with RF electric and magnetic fields. Pure copper and also copper alloys undergo mechanical and thermal treatments to be hardened and strengthened during manufacturing, although their mechanical properties significantly change after heating above 590°C. High temperature brazing and diffusion bonding are assembly methods widely used to manufacture ultra-high vacuum accelerating devices. However, these processes, occurring at about 800–1000°C, significantly affect the mechanical properties of copper and copper alloys. We introduce here a novel Tungsten Inert Gas welding procedure, which is fast and keeps the high-gradient surfaces of the cavity and other components well below the copper annealing temperature. This process may be successfully used to manufacture copper-based accelerating components. This technology further preserves the hardness and cleanliness of copper in order to achieve the maximum accelerating gradient.

47 OTHER INSTRUMENTATION↗
NASA NTRS1981

Oxidation-induced contraction and strengthening of boron fibers

An investigation was conducted to measure and understand the physical and mechanical effects that occur in boron fibers during and after thermal treatment in a controlled oxygen argon gaseous mixture. Of principal concern was the optimization of this treatment as a secondary processing method for significantly improving fiber tensile strength. Strengthening was accomplished by an oxidation induced axial contraction of the fiber and a resulting axial compression of strength limiting flaws within the fiber's tungsten boride core. Various physical observations were used to develop mechanistic models for oxidation, contraction, and flow formation. Processing guidelines are discussed for possibly exceeding the 5.5 GN/sq m strength limit and also for achieving fiber strengthening during application of boron containing diffusion barrier coatings.

Dicarlo, J. A.↗
NASA NTRS1996

Surveying Dead Trees and CO2-Induced Stressed Trees Using AVIRIS in the Long Valley Caldera

Since 1980 the Long Valley Caldera in the eastern Sierra Nevada (California) has shown signs of renewed volcanic activity. Frequent earthquakes, a re-inflation of the caldera, hydrothermal activity and gas emissions are the outer symptoms of this renewed activity. In 1990 and 1991 several areas of dying trees were found around Mammoth Mountain. The cause of the die off of the trees was first sought in the persistent drought in the preceding years. However, the trees died regardless of age and species. Farrar et al. (1995) started a soil-gas survey in 1994 in the dead-tree areas and found carbon dioxide concentrations ranging from 30 to 96% at soil depths between 30 and 60 cm. CO2 concentrations in the atmosphere are usually around 0.03% and in the soil profile CO2 levels do commonly not exceed 4 to 5%. Although not much is known about the effect of high levels of carbon dioxide in the soil profile on roots, it is most likely that the trees are dying due to oxygen deprivation: the CO2 drives the oxygen out of the soil. So far, four sites of dead trees have been mapped around Mammoth Mountain. The two largest dying trees sites are located near Horseshoe Lake and near Mammoth Mountain Main Lodge covering approximately an area of 10 and 8 ha respectively. Analysis of the gas composition regarding the He-3/He-4 ratio and the percentage biogenic carbon reveals the source of the gas: the magma body beneath the Long Valley Caldera. Until recently it was not known that volcanoes release abundant carbon dioxide from their flanks as diffuse soil emanations. As a result of the magma gas emission around Mammoth Mountain there is an excellent sequence of dead trees, stressed trees, healthy trees and bare soil surfaces. This research site provides excellent opportunities to: (1) Study the capabilities of imaging spectrometry to map stressed (and dead) pine and fir species; (2) Study methods to separate the vivid vegetation, stressed vegetation and dead vegetation from the soil background of glacial deposits and crystalline rocks. The dead tree areas are located on the flanks of Mammoth Mountain (N:37 deg 37' 45" and W:119 deg 02' 05") at an elevation between 2600 and 3000 meters. The area is covered by an open type of Montane Forest. The dominant tree species are Lodgepole Pine (Pinus contorta), the Red Fir (Abies magnifica) and the Jeffrey Pine (Pinus jeffreyi). The soil surface near Horseshoe Lake is generally fairly bright. The surface is covered by glacial deposits (till) consisting mainly of weathered granitic rocks.

deJong, Steven M.↗
DOE OSTI2023

Phase-field modeling of dislocation–interstitial interactions

The mechanical behavior of body-centered cubic (BCC) materials can be dramatically affected by the presence of interstitial solute atoms. Here we present a new phase-field dislocation dynamics formulation to include the diffusion of interstitials. Short-range interactions are accounted for by a concentration-dependent lattice energy, and long-range interactions are accounted for by modifications to the elastic energy. The interstitial diffusion law introduces gradients that require methods for minimizing Gibbs oscillations, which is done via a modified Green’s function. The formulation is general to any solute-solvent system and is applied here to Nb-O as a model system, whose interstitial parameters are obtained from ab initio calculations. The effect of O on the core structures of Nb edge and screw dislocations is calculated. The diffusion of O to form interstitial atmospheres around dislocation cores is simulated, as well as the critical stresses required for dislocations to break away or cross slip from these atmospheres. Future applications of the method to simulate complex interstitial embrittlement mechanisms are discussed.

36 MATERIALS SCIENCE↗
NASA NTRS1977

The effect of carbon on phosphate reduction

Several experiments were performed in order to evaluate the effect of carbon on phosphate reduction in synthetic systems. It was attempted to simulate in the experiments conditions occurring during lunar impact processes, but without shock pressure. Temperature, oxygen fugacity, and bulk chemistry were evaluated separately in order to determine the conditions which are suitable for carbon reduction. It appears on the basis of the results of the reported investigation that carbon can be an effective reducing agent during reheating events such as those encountered by lunar soils and breccias. Phosphate reduction may be viewed as a two-step process in which carbon is mobilized as CO during heating and preferentially dissolved in the metal phase. It then acts as a reducing agent on cooling. Gas phase transport and diffusion of carbon in metal are sufficiently rapid to allow uniform carbon distribution both within and between metal grains. The availability of metal from meteorites and carbon from the solar wind is probably sufficient to make reduction by carbon a significant process on the lunar surface.

Friel, J. J.↗
DOE OSTI2022

Oxygen and Proton Transport in Flooded Graphene Pores with N-Dopants and Defects

Reactant transport is an important consideration in the design of ideal electrode structures. For the oxygen reduction reaction catalyzed by Pt/C in proton exchange membrane fuel cell cathodes, O 2 and H + delivery to Pt surfaces and H 2 O transport away are required. Some Pt nanoparticles may only be accessible via micropores that are too small for ionomer molecules to enter, possibly requiring flooding for H + transport. Here, to test if these “buried” Pt particles can play a role in activity through this proposed transport mechanism, we have performed atomic-scale simulations based on reactive force field molecular dynamics with an emphasis on confinement below 20 Å. Diffusion coefficients as a function of the molar concentration and local environment have been evaluated in water domains confined in two-dimensional graphene nanochannels of various channel heights representing a morphological model for micropores in proton exchange fuel cell cathodes. Our study shows that local atomic-scale structures can strongly modify H + , O 2 , and H 2 O transport rates in flooded micropores less than 20 Å in size. We find that there is a critical crossover in diffusion behavior around the 20 Å spacing with larger pores having bulk-like diffusion properties and confinement below 20 Å monotonically decreases diffusion rates. As pore size decreases, we observe locally dispersed water regions that ultimately strand reactants from long-distance transport. These findings suggest that flooded micropores may in fact be viable transport pathways for relevant reactants and products if the pore walls on opposite sides remain separated by ≥10 Å separation. Furthermore, the confinement effect is so strong that N-doping and C-vacancy defects in the C pore wall have only a minimal impact on diffusion rates and their effects are counterintuitively more apparent at larger spacings. These findings provide valuable insight regarding cathode performance and the role “stranded” catalyst particles may play in fuel cell cathodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Critical Practices in Rigorously Assessing the Inherent Activity of Nanoparticle Electrocatalysts

Accurate activity measurements for electrocatalytic materials are the backbone of impactful electrocatalyst research. Inherent to accurate measurements is the correct accounting of the active catalyst sites and the design of experiments to ensure that these sites are participating in the measured reaction. Improvements in electrocatalyst activity for fuel cell reactions (hydrogen oxidation and oxygen reduction) are essential for the widespread adoption of this carbon-neutral energy source. Activities for these half-reactions can be reported in a variety of ways including specific activities, mass activities, volumetric activities, and half-wave potentials. These values are traditionally measured with a rotating disk electrode (RDE) in which the electrocatalyst is supported on a porous active layer film attached to the RDE. To accurately measure electrocatalyst activity with an RDE, two major sources of errors must be addressed: (i) accurate electrochemical surface area (ECSA) quantification and (ii) fast diffusion of reactants through the active layer film. In this contribution, we first aim to detail through RDE experiments and mass transport modeling the potential errors that can be observed when these factors are not properly addressed. We then present recommendations and discuss techniques for properly constructing electrocatalyst thin films and characterizing the ECSA on monometallic and novel alloy electrocatalysts. These practices, when adopted, ensure greater confidence and reliability in reports of electrocatalyst activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1990

On determining ice accumulation rates in the past 40,000 years using in situ cosmogenic C-14

Radiocarbon is produced in situ in ice by nuclear spallations of oxygen by cosmic ray neutrons. As the firn accumulates, it acquires a predictable concentration of in situ C-14, inversely proportional to the rate of accumulation. Most of this production occurs when the amount of overlying ice is less than (2-3) Lambda, where lambda is the absorption mean free path for cosmic radiation in ice, about 150 g/sq cm, i.e. within the top 10 m. In most accumulation areas, this is firn. In situ produced C-14 is added to the firn as it accumulates, and is not expected to be lost by diffusion. During the firn-ice transition, atmospheric CO2 is trapped, adding (C-14)02 to the ice. The signature of in situ C-14 is however not obliterated since about 60 percent of in situ C-14 is instantly oxidized to (C-14)O in the ice. The results available to date are discussed, and it is proposed that this in situ (C-14)O can be used to determine ice accumulation rates back to 40,000 yrs in the past.

Lal, D.↗
NASA NTRS1981

On the distribution of noble gases in Allende - A differential oxidation study

The investigation makes use of an oxidizing technique which is based on methods widely employed in light stable isotope analysis. The utilization of closed-system differential combustion in molecular oxygen in an ultra-high vacuum system on-line with a spectrometer makes it possible to conduct precise abundance and isotopic measurements of all gases released in progressive oxidation and/or thermal outgassing of the host phases. Attention is given to the noble gases mobilized in progressive oxidation of a carbon-rich acid residue and a fine-grained matrix separate. The progressive oxidation of the Allende matrix is discussed. Release occurred over three distinct intervals, characterized by oxidation below 600 C, gas mobilization between 630 and 750 C, and high-temperature diffusive release.

Frick, U.↗
NASA NTRS1991

Chemical spray pyrolysis of Tl-Ba-Ca-Cu-O high-T(sub c) superconductors for high-field bitter magnets

The deposition of Tl-Ba-Ca-Cu-O thick films by spray pyrolyzing a Ba-Ca-Cu-O precursor film and diffusing thallium into the film to form the superconducting phase is examined. This approach was taken to reduce exposure to thallium and its health and safety hazards. The Tl-Ba-Ca-Cu-O system was selected because it has very attractive features which make it appealing to device and manufacturing engineering. Tl-Ba-Ca-Cu-O will accommodate a number of superconducting phases. This attribute makes it very forgiving to stoichiometric fluctuations in the bulk and film. It has excellent thermal and chemical stability, and appears to be relatively insensitive to chemical impurities. Oxygen is tightly bound into the systems, consequently there is no orthorhombic (conductor) to tetragonal (insulator) transition which would affect a component's lifetime. More significantly, the thallium based superconductors appear to have harder magnetic properties than the other high-Tc oxide ceramics. Estimates using magnetoresistance measurements indicate that at 77 K Tl2Ba2CaCu2O10 will have an upper critical field, H(sub c2) fo 26 Tesla for applied fields parallel to the c-axis and approximately 1000 Tesla for fields oriented in the a-b plane. Results to date have shown that superconducting films can be reproducibly deposited on 100 oriented MgO substrates. One film had a zero resistance temperature of 111.5 K. Furthermore, x ray diffraction analysis of the films showed preferential c-axis orientation parallel to the plane of the substrate. These results have now made it possible to consider the manufacture of a superconducting tape wire which can be configured into a topology useful for high-field magnet designs. The research which leads to the preparation of these films and plans for further development are reviewed.

Derochemont, L. Pierre↗
DOE OSTI2023

Rational Design of Fluorinated Electrolytes for Low Temperature Lithium‐Ion Batteries

Abstract Nonaqueous carbonate electrolytes are commonly used in commercial lithium‐ion battery (LIB). However, the sluggish Li + diffusivity and high interfacial charge transfer resistance at low temperature (LT) limit their wide adoption among geographical areas with high latitudes and altitudes. Herein, a rational design of new electrolytes is demonstrated, which can significantly improve the low temperature performance below −20 °C. This electrolyte is achieved by tailoring the chemical structure, i.e., altering the fluorination position and the degree of fluorination, of ethyl acetate solvent. It is found that fluorination adjacent to the carbonyl group or high degree of fluorination leads to a stronger electron‐withdrawing effect, resulting in low atomic charge on the carbonyl oxygen solvating sites, and thus low binding energies with Li + ions at LT. The optimal electrolyte 2,2,2‐trifluoroethyl acetate (EA‐f) shows significantly improved cycle life and C‐rate of a NMC622/graphite cell when cycled at −20 °C and −40 °C, respectively. In addition to superior LT performance, the electrolyte is nonflammable and tolerant for high voltage charging all owing to its fluorine content. This work provides guidance in designing next‐generation electrolytes to address the critical challenge at subzero temperatures.

25 ENERGY STORAGE↗
DOE OSTI2020

Deconvolution of Water-Splitting on the Triple-Conducting Ruddlesden–Popper-Phase Anode for Protonic Ceramic Electrolysis Cells

Triple-conducting materials have been proved to improve the performance of popular protonic ceramic electrolysis cells. However, partially because of the complexity of the water splitting reaction involving three charge carriers, that is, oxygen (O 2– ), proton (H + ), and electron (e – ), the triple-conducting reaction mechanism was not clear, and the reaction conducting pathways have seldom been addressed. In this study, the triple conducting Ruddlesden–Popper phase Pr 1.75 Ba 0.25 NiO 4+δ as an anode on the BaCe 0.7 Zr 0.1 Y 0.1 Yb 0.1 O 3–δ electrolyte was fabricated and its electroresponses were characterized by electrochemical impedance spectroscopy with various atmospheres and temperatures. The impedance spectra are deconvoluted by means of the distribution of the relaxation time method. The surface exchange rate and chemical diffusivity of H + and O 2– are characterized by electrical conductivity relaxation. The physical locations of electrochemical processes are also identified by atomic layer deposition with a surface inhibitor. A microkinetics model is proposed toward conductivities, triple-conducting pathways, reactant dependency, surface exchange and bulk diffusion capabilities, and other relevant properties. Lastly, the rate-limiting steps and suggestions for further improvement of electrode performance are presented.

25 ENERGY STORAGE↗
DOE OSTI2021

Stabilized Lithium, Manganese-Rich Layered Cathode Materials Enabled by Integrating Co-Doping and Nanocoating

While lithium, manganese-rich (LMR) layered oxide cathode materials offer high energy density (>900 Wh kg –1 ) and low cost, LMR is susceptible to continuous capacity and voltage decay from the oxygen migration and side reaction with aqueous electrolyte at high voltage. Herein, the integration of Na/F co-doping (CD) and AlF 3 coating on LMR is achieved without the need of complex atomic layer deposition. Akin to pristine and CD samples, CD with 1 wt % AlF 3 (CD-1.0 wt %) shows excellent electrochemical performance with the capacity and voltage retentions of 93 and 91% after 150 cycles at 0.5C, respectively, and increased ionic conductivity. Spectroscopic analysis indicates that the coating mainly influences the Co distribution, where Co is enriched on the surface, and partial diffusion of Al 3+ ions toward the bulk, leading to a slight change of transition-metal (TM) valence states at the nanometer scale and the formation of a stable Li x (CoAl)O y phase. Post-cycling analysis reveals that CD-1.0 wt % can alleviate the formation of rock-salt structure and Mn dissolution. Besides, little to no metal segregation is detected for the cycled CD-1.0 wt % sample. This finding presents the first instance to apply co-doping and AlF 3 coating as a new strategy to enhance the structural homogeneity and takes another step toward their commercial viability.

25 ENERGY STORAGE↗
NASA NTRS1986

N(+)-N and O(+)-O interaction energies, dipole transition moments, and transport cross sections

Complete sets of ion-atom interaction energies have been computed for nitrogen and oxygen with accurate large scale structure calculations. The computed energies agree well with the accurate potential curves available from spectroscopic measurement. The state functions from the nitrogen calculations have been applied to determine the transition moment for all allowed dipole transitions. These results can be combined to compute a detailed radiation spectrum such as that required to define the highly nonequilibrium environment of aeroassisted orbital transfer vehicle (AOTV). The long-range interaction energies have been used to determine the ion-atom resonance charge exchange cross sections that are important for transport processes such as diffusion. A calculation to determine reliable transport properties for energies that include the AOTV temperature range from these computed properties is described.

Partridge, H.↗
DOE OSTI2022

Numerical and Experimental Investigations on the Ignition Behavior of OME

On the path towards climate-neutral future mobility, the usage of synthetic fuels derived from renewable power sources, so-called e-fuels, will be necessary. Oxygenated e-fuels, which contain oxygen in their chemical structure, not only have the potential to realize a climate-neutral powertrain, but also to burn more cleanly in terms of soot formation. Polyoxymethylene dimethyl ethers (PODE or OMEs) are a frequently discussed representative of such combustibles. However, to operate compression ignition engines with these fuels achieving maximum efficiency and minimum emissions, the physical-chemical behavior of OMEs needs to be understood and quantified. Especially the detailed characterization of physical and chemical properties of the spray is of utmost importance for the optimization of the injection and the mixture formation process. The presented work aimed to develop a comprehensive CFD model to specify the differences between OMEs and dodecane, which served as a reference diesel-like fuel, with regards to spray atomization, mixing and auto-ignition for single- and multi-injection patterns. The simulation results were validated against experimental data from a high-temperature and high-pressure combustion vessel. The sprays’ liquid and vapor phase penetration were measured with Mie-scattering and schlieren-imaging as well as diffuse back illumination and Rayleigh-scattering for both fuels. To characterize the ignition process and the flame propagation, measurements of the OH* chemiluminescence of the flame were carried out. Significant differences in the ignition behavior between OMEs and dodecane could be identified in both experiments and CFD simulations. Liquid penetration as well as flame lift-off length are shown to be consistently longer for OMEs. Zones of high reaction activity differ substantially for the two fuels: Along the spray center axis for OMEs and at the shear boundary layers of fuel and ambient air for dodecane. Additionally, the transient behavior of high temperature reactions for OME is predicted to be much faster.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2026

Graphene oxide precursor effects on 3D-printed carbon scaffolds

Manganese oxide (MnO 2 ), an earth-abundant material, is a promising component for energy storage devices, with uses in both pseudocapacitors and batteries. However, high MnO 2 loading often leads to reduced performance due to poor ion diffusion. 3D printing, particularly using the direct ink writing (DIW) technique, offers a solution by enabling the fabrication of electrodes with hierarchical porous structures and open channels that enhance mass transport and ion diffusion. Previous work demonstrated that 3D-printed graphene aerogels with MnO 2 coatings exhibited excellent electrochemical performance, even with thick electrodes, due to their optimized structure. Building on this work, the current study investigates the performance differences between aerogels developed using graphene oxide (GO) and reduced graphene oxide (rGO) as carbon precursors. Both materials were incorporated into thixotropic inks, 3D-printed into lattice structures, and carbonized. Despite expected similarities between the final graphene aerogel, rGO-based aerogels exhibited superior areal capacitance, compared to GO-based aerogels. These differences are attributed to the lower oxygen content and defect density of rGO, which influence its interaction with cellulose viscosifiers in the ink formulation. Brunauer–Emmett–Teller (BET) surface area analysis revealed that rGO aerogels exhibit a larger surface area and mesoporous structure, further enhancing their performance. When coated with MnO 2 , rGO-based aerogels maintained their superior capacitive behavior over GO-based aerogels. This study highlights the effect of carbon precursor on the end performance of graphene aerogels.

Materials science↗