Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Effect of time-dependent flight loads on turbofan engine performance deterioration

An analytic evaluation of the dynamic effects of two flight load conditions of the JT9D-7/747 propulsion system is conducted. Predicted performance changes associated with a once-per-flight vertical gust and a typical revenue service landing are calculated. The predicted dynamic load effects on thrust specific fuel consumption are found to be negligible. The results indicate that the quasi-steady state approach to flight loads modeling is adequate to investigate the factors important to the deterioration process.

Lewis, B. L.↗

A study of the viscous dissipation and surface loading on a vibrating surface

The energy dissipated by viscosity at the edge of a vibrating flat plate is calculated and compared to the radiated acoustic energy. A correction to the Kirchhoff integral estimate of the noise is derived. For Helmholtz number of order unity and smaller the dissipation can be comparable to or greater than the acoustic energy. A viscous compressible theory of the load distribution on a vibrating two dimensional body is developed. First it is shown that load calculations based on potential theory and the Newmann uniqueness condition (continuity of potential or pressure on the surface) are not in agreement with experiment or the more correct viscous theory. For a flat plate airfoil the eigensolution of potential theory is indeterminant while viscous theory yields a unique solution that has square root singularities at the edges. It is also shown that for compact surfaces the far field acoustics depend only on the magnitude of the eigensolutions of potential theoy and so will be uniquely determined by the viscous theory. It is suggested that the general viscous theory of vibrating surfaces with cross sectional geometry will lead to results in agreement with expermentally measured load distributions.

Yates, J. E.↗

NASA Dryden Flight Loads Research Facility

The Dryden Flight Loads Research Facility (NASA) and the associated equipment for simulating the loading and heating of aircraft or their components are described. Particular emphasis is placed on various fail-safe devices which are built into the equipment to minimize the possibility of damage to flight vehicles. The equipment described includes the ground vibration and moment of inertia equipment, the data acquisition system, and the instrumentation available in the facility for measuring load, position, strain, temperature, and acceleration.

Walter J Sefic↗

Experimental investigation of active loads control for aircraft landing gear

Aircraft dynamic loads and vibrations resulting from landing impact and from runway and taxiway unevenness are recognized as significant in causing fatigue damage, dynamic stress on the airframe, crew and passenger discomfort, and reduction of the pilot's ability to control the aircraft during ground operations. One potential method for improving operational characteistics of aircraft on the ground is the application of active control technology to the landing gears to reduce ground loads applied to the airframe. An experimental investigation was conducted which simulated the landing dynamics of a light airplane to determine the feasibility and potential of a series hydraulic active control main landing gear. The experiments involved a passive gear and an active control gear. Results of this investigation show that a series hydraulically controlled gear is feasible and that such a gear is very effective in reducing the loads transmitted by the gear to the airframe during ground operations.

Mcgehee, J. R.↗

Reduction of computer usage costs in predicting unsteady aerodynamic loadings caused by control surface motion. Addendum to computer program description

Changes to be made that provide increased accuracy and increased user flexibility in prediction of unsteady loadings caused by control surface motions are described. Analysis flexibility is increased by reducing the restrictions on the location of the downwash stations relative to the leading edge and the edges of the control surface boundaries. Analysis accuracy is increased in predicting unsteady loading for high Mach number analysis conditions through use of additional chordwise downwash stations. User guideline are presented to enlarge analysis capabilities of unusual wing control surface configurations. Comparative results indicate that the revised procedures provide accurate predictions of unsteady loadings as well as providing reductions of 40 to 75 percent in computer usage cost required by previous versions of this program.

Rowe, W. S.↗

Study of fatigue durability of advanced composite materials under conditions of accelerated loading

The effect of temperature on the tension-tension fatigue life of the T300/5208 graphite/epoxy angle-ply laminate system was investigated in an effort to develop an acceptable and reliable method of accelerated loading. Typical S log sub 10 N curves were determined experimentally at 25 C, 75 C, and 115 C. The time-temperature superposition principle was employed to find the shift factors of uniaxial fatigue strength, and a general linear equation of S log sub 10 N for shifting purpose was established. The combined techniques of cyclic creep measurements and optical microscopy upon fatigue failure allow some assessment of the possible physical basis of S log 10 N curve shifting. Before fatigue, the laminates at all test temperatures and stress levels undergo a unique damage mechanism during fatigue loading. It is concluded that an accelerated loading method is feasible.

Shih, H. M.↗

Methods and models for predicting fatigue crack growth under random loading

Papers are presented in the volume summarizing the baseline data, methodology, procedures, and results of a round-robin analysis which was conducted to predict the fatigue crack growth in 2219-T851 aluminum center-cracked specimens subjected to flight loading in random cycle-by-cycle format. The objective of the analysis was to assess whether data from constant-amplitude fatigue crack growth tests on center-cracked specimens can be used to predict fatigue crack growth lives under random loading. The following approaches are discussed in detail: a root-mean-square approach, a crack-closure model, a multi-parameter yield zone model, and a load-interaction model.

Chang, J. B.↗

Effects of blade loading and rotation on compressor rotor wake in end wall regions

This study was carried out to understand the effects of blade loading and rotation on the rotor end wall flow structure, including the wake. The measurements were taken with a stationary three sensor hot wire located at the exit of a compressor rotor. The signal was ensemble averaged to derive all the three components of velocity and six components of stresses at the exit. Measurements were made at two different rotational speeds (1753 and 1010 rpm) and at two differing blade loadings at several radii near the hub and the annulus wall. The wake decay in the annulus wall region is found to be much more rapid than the mid span regions. Furthermore, both the loading and rotation of the blade have appreciable influence on the end wall flow and wake structure. Interaction of the annulus and hub wall boundary layers (and secondary flow resulting from these) have appreciable influence on the wake structure in the endwall regions.

Lakshminarayana, B.↗

The simulation of time varying ascent loads on arrays of Shuttle tiles in a large transonic tunnel

A large variety of tests were made to determine the strength, fatigue and thermal characteristics of the thermal-protection system of the Shuttle orbiter. The present paper describes first-launch-critical tests which were conducted in the Langley 8-Foot Transonic Pressure Tunnel (8'TPT) which simulated the time histories of Shuttle ascent loads on tile arrays bonded to structures which accurately duplicated those of the Shuttle. The time varying free-stream conditions were provided by controlling the deflection angle history of diffuser spoiler flaps in an automated way. Time histories of the critical-load parameters imposed on the tile arrays in the tunnel are compared in the paper to those expected in flight. In addition, the effect of repeated load pulses on the smoothness of the surface and condition of the tiles is discussed briefly.

Bobbitt, P. J.↗

Static calibration for measurement of loads in wind tunnel tests on Shuttle surface tiles

A description is given of the procedures used for the static calibrations of the Coe (1981) sensor array to determine normal force, pitching moment, and rolling moment from the ensemble of sensor outputs. The use of independent data to confirm the validity of the calibration is also described. Two methods are used in calibrating the Coe sensors. In the first, calibration loads and readings are arranged in matrix form and are assumed to be related in a linear fashion. In the second, each Coe sensor reading is regarded as a sum of contributions from each of the calibration loads. It is shown that the Coe load sensors, in conjunction with either of two data analysis methods, can be used to determine the forces and moments experienced by a Shuttle TPS tile.

Rummler, D. R.↗

Power-Factor Controller With Fast Load Response

Sudden changes in induced emf sensed. In refinement of soft starting three phase power-factor controller, additional components enable circuit to respond quickly to sudden increase in motor load. Rapid-load-response addition senses induced motor emf to detect sudden load increase and generates command signal to increase applied power in response.

Nola, F. J.↗

Structural dynamics payload loads estimates

Methods for the prediction of loads on large space structures are discussed. Existing approaches to the problem of loads calculation are surveyed. A full scale version of an alternate numerical integration technique to solve the response part of a load cycle is presented, and a set of short cut versions of the algorithm developed. The implementation of these techniques using the software package developed is discussed.

Engels, R. C.↗

Performance and load data from Mod-0A and Mod-1 wind turbine generators

Experimental data, together with supporting analysis, are presented on the power conversion performance and blade loading of large, horizontal-axis wind turbines tested at electric utility sites in the U.S. Four turbine rotor configurations, from 28 to 61 meters in diameter, and data from five test sites are included. Performance data are presented in the form of graphs of power and system efficiency versus free-stream wind speed. Deviations from theoretical performance are analyzed statistically. Power conversion efficiency averaged 0.34 for all tests combined, compared with 0.31 predicted. Round blade tips appeared to improve performance significantly. Cyclic blade loads were normalized to develop load factors which can be used in the design of rotors with rigid hubs.

Spera, D. A.↗

Thermomechanical loading of multilayered cylindrical geometries in thermal cycling from 300 to 1300 K

The principal of multiple material layering is well known as an effective method of reducing heat transfer; however, thermal gradients can impose significant loads and lead to delamination and subsequent component failure. An analysis is developed and experimental data are discussed for the thermomechanical effects of multilayered materials on a heat sink substrate of cylindrical geometry subject to thermal cycling. The geometry is heated in cross-flow by a high-velocity flame and cooled in crossflow by ambient-temperature air from a critical flow orifice. Each layer of material possesses a threshold beyond which small changes in temperature or mechanical loading greatly influence the life in thermal cycling of the layered materials. Comparisons are made between the thermomechanical loads predicted by various numerical codes for the linear case and by a simplified analytic model.

Hendricks, R. C.↗

Analytical and experimental study of a standing torus with normal loads

Finite element analysis is applied to study the large deflection and stress of a thin-walled pressurized torus loaded by normal contact with a plane. Experimentally determined stresses are compared to those resulting from finite element analysis at various meridional and circumferential coordinates of the torus, including the footprint area. Circumferential strains compare favorably while meridional strains are higher in the finite element analysis, probably due to slippage of the boundary at the rim. The STAGS finite element computer program was used. The purpose of the study was to evaluate the various program options for structural loading, for material modeling, for stress analysis, and for grid refinement. The experimental model, a thin-walled rubber tube mounted on a steel cylindrical rim, provided measured results to compare with various analytical trade-offs. It was found that there was almost no difference in predicted deflections or stress distributions between linear and nonlinear material description. However, the difference between linear analysis and that of geometric nonlinearities utilizing incremental loading was marked.

Mack, M. J., Jr.↗

Evaluation of mounting bolt loads for Space Shuttle Get Away Special (GAS) adapter beam

During the prototype vibration tests of the GAS adapter beam, significant impacting of the beam at its support points was observed. The cause of the impacting was traced to gaps under the mounting bolt heads. Because of the nonlinear nature of the response, it was difficult to evaluate the effects which Shuttle launch dynamics might have on the mounting bolt loads. A series of tests were conducted on an electrodynamic exciter in which the transient acceleration time histories, which had been measured during the Space Transportation System-1 (STS-1; Space Shuttle mission 1) launch, were simulated. The actual flight data had to be filtered and compensated so that it could be reproduced on the shaker without exceeding displacement and velocity limitations. Mounting bolt loads were measured directly by strain gages applied to the bolts. Various gap thicknesses and bolt torques were investigated. Although increased gap thickness resulted in greater accelerations due to impacting, the bolt loads were not significantly affected. This is attributed to the fact that impacting excited mostly higher frequency modes which do not have significant modal mass.

Talapatra, D. C.↗

The relationship of compliance changes during fatigue loading to the fracture of composite materials

The study outlined here is based on measurements of the change in engineering stiffness values induced by the development of damage in composite laminates during quasi-static or cyclic (fatigue) loading. These changes are found to be related to the individual details of the damage events in the laminates, as well as to the residual strength and life of the laminates. It is believed that the stiffness changes can also be used to relate composite material behavior under cyclic loading to its behavior under quasi-static loading. Results are presented for both notched and unnotched laminates. Compliance changes are found to be caused by damage events that bring about both global and local redistributions of stress. It is also found that the redistributions of stress determine the residual strength of the laminate. The quantitative link between compliance changes and fracture strength is the mechanics of the internal stress redistributions.

Reifsnider, K. L.↗

Effects of random member length errors on the accuracy and internal loads of truss antennas

The effects of random member length errors on the surface accuracy, the defocus, and the residual, internal loads of tetrahedral truss antenna reflectors have been studied analytically. The analytical procedure involves performing multiple, deterministic finite element structural analyses for a particular truss. For each analysis, the normally distributed, random member length errors are selected by random number generator. A best fit paraboloid analysis is used to determine a root mean square error and defocus from each analysis. The statistical properties of these quantities as well as the internal loads are calculated from the results of many independent analyses. Results indicate that the number of members in a tetrahedral truss antenna of a given diameter has a significant effect on surface accuracy, defocus and internal loads. It was also found that the member axial stiffnesses and antenna focal length have a very small effect on reflector surface accuracy.

Greene, W. H.↗